Search Documents

By Marcella Gautê Cavalcante Xavier

A presente proposta tem por objetivo desenvolver uma análise experimental da liga hipereutética Sn-0,5%Ni solidificada unidirecionalmente em regime transitório de fluxo de calor contra chapa molde de cobre. A liga foi avaliada quanto a sua microestrutura bruta de fusão e suas respectivas correlações com os parâmetros térmicos (velocidade da frente eutética -VE e taxa de resfriamento eutética -?E) e propriedades mecânicas. Os resultados mostram que a morfologia microestrutural predominante é composta por células ricas em estanho (β-Sn) circundadas por mistura eutética Sn+intermetálico tipo NiSn. Uma transição microestrutural foi observada entre as posições 15mm (?E=1,7°C/s) e 30mm (?E=1,1°C/s), de célula regular (CR)?célula tipo placa (CTP). Notou-se ainda a presença de intermetálicos primários NiSn distribuídos ao longo da matriz nas posições iniciais do lingote. Valores superiores de limite de resistência à tração (σu=26 MPa) e limite de escoamento (σy=21 MPa) foram encontrados para a posição 6mm a partir da base refrigerada do lingote, podendo estar relacionados com a estrutura celular mais refinada e também com a presença dos intermetálicos primários NiSn. O alongamento específico (?) comportou-se de maneira inversa, visto que as estruturas mais grosseiras (CTP) e a ausência de intermetálicos primários são responsáveis por facilitar a deformação plástica na estrutura da liga Sn-0,5%Ni, aumentando seu nível de ductilidade.

Oct 30, 2017

By J. A. Haskin

The Engineering Department at Flin Flon has the following responsibilities: 1. Underground Surveying. 2. Open-Pit Surveying and Supervision of Blasting. 3. Mine Geology and Examination of Prospects. 4. Design of Plant Additions and Improvements. 5. Miscellaneous Field W ork, Reports, etc. The entire surface plant, as well as the underground workings, are located by co-ordinates based on a triangulation system covering an area approximately one mile long by one-half mile wide. The origin of this system and one end of the base-line is the southwest corner of Township 67, Range 29, west of the Principal Meridian. The bearing of the base-line was determined from the township boundary, which runs true north, so that all other bearings are almost astronomical. This is a great convenience when our surveys must be tied to mineral claims, rights-of-way, and land subdivisions. As the base-line extends across Flin Flon lake, its measurement across smooth ice was simple and accurate. The length, slightly over 1,600 feet, has been adjusted for the temperature and tension of the standard tapes used and checked sufficiently to ensure a maximum error of 1 : 15,000. Each angle was repeated ten times, but as no special refinements were used, errors of as much as four or five seconds are possible. The elevation of the origin of the triangulation system was approximately 1,050 feet above sea level. The use of this true elevation in our surveys would have resulted in negative elevations underground as soon as the mine reached a depth greater than 1,050 feet. To avoid this complication we therefore added 4,000 feet to this elevation. The collar of the Main shaft, for example, which is actually 1,072 feet above sea level, appears in our records as at elevation 5,072. Underground surveying, which follows standard practice, is done by two mine surveyors who share three helpers. The meridian is taken underground from two wires hung in either of the two vertical shafts.

Jan 1, 1935

By E. Hinton, L. Bloomquist

"This paper describes a guidance system for autonomous underground mining vehicles, which does not require any infrastructure or inertial positioning systems to aid the guidance process.BackgroundINCO Limited mines approximately ten million tons per annum through 12 operating mines in the Sudbury, Ontario, area (Fig. 1). With challenges from operating in a cyclical marketplace as well as new technologies making alternative nickel ores more competitive to refine, the Mines Research department embarked on a strategy that pointed toward automation as a tool to help the company become even more economical in mining.The mining industry has been looking for ways and means to mine orebodies more and more inexpensively. Automation and the lessons learned from manufacturing had a great influence in the direction of research at INCO Limited over the past ten years. Guidance systems have evolved over the years but the majority of commercially available systems rely on some form of infrastructure. This, in part, has caused some resistance from operators to install and maintain automated or semi-automated systems for guidance of underground machinery.Internal industrial studies cited travel time to and from the workplace as one of the major time sinks in the shift of underground miners. Depending on the mine, it may be as much as two hours moving in and out of an area. Some work areas have accommodated this by having “hot changes” at the work place. However, at some point in time, there are two people tasked with the same job and on site at the same time to make this overlap occur.Tele-operation of underground hard rock equipment eliminated this overlap and also provided a comfortable environment in which to work. By taking advantage of the communications network installed, the miners proved that they could operate three machines with relative ease. This was accomplished by a vision-based, “painted line,” autonomous guidance system termed the light rope system.With a few years’ experience with the system, some issues have arisen, including the cost of the rope itself (Fig. 2).The vehicle’s route is limited to the paths defined by the light rope, and a system of switching power to the light rope to select different routes is required. The rope itself is subject to damage from nearby blasts. Also, the system offers no obstacle detection; the vehicle may be switched off as a means of shutting the machine down thus protecting personnel in the area."

Jan 1, 2001

By Mika Muinonen

"Dewatering of nickel concentrate at the INCO Thompson integrated mine-metallurgical site takes place within the smelter plant. The eight original 60 foot diameter cable torque thickeners of which four were operational and eight Dorrco internal drum filters have been replaced with a single Outokumpu high rate thickener and a single Lasta pressure filter. The modernization has resulted in a filter cake which has a more stable and lower moisture content. Control of the entire dewatering process has been improved and costs have been reduced.Typical filter cake produced from the Dorrco filters during processing of high tonnages of Birchtree mine ore was ~20% moisture vs. ~13% moisture for concentrate produced from the Thompson mine ore. The high moistures were correlated with the amount of fine magnesium silicate gangue in the concentrate. As Birchtree ore processing rates have increased, this filter cake moisture became unacceptable because of material handling problems and the impact on furnace metallurgy. The Dorrco filters were replaced with the Lasta filter in 2003 that has consistently produced filter cake at ~11% moisture.This paper summarizes the piloting, design, installation and commissioning of the modernized dewatering circuit.INTRODUCTIONThe Thompson integrated nickel processing facility was built in 1958 and originally consisted of a mine-mill-smelter and, soon after, a refinery.Nickel concentrate is pumped from the mill as a dilute slurry directly to the smelter facility ~200 meters along an unheated pipe trestle. Originally, nickel concentrate was de-watered using up to 8 conventional 60-foot diameter thickeners and 8 internal vacuum drum filters."

Jan 1, 2006

By Edward J. Cording, William H. Hansmire

INTRODUCTION The Washington Metro, a rapid transit system that will serve the District of Columbia, Virginia, and Maryland, has been under construction for about two years. Construction of the Metro by the Washington Metropolitan Area Transit Authority involves a large amount of cut and cover, soil tunnel, and rock tunnel construction. To aid initial construction and improve future designs, performance observations were undertaken on tunnels in the initial construction phase. The University of Illinois Department of Civil Engineering was engaged to carry out a comprehensive program of field observations and measurements for this purpose. One part of the program was on the first soft ground tunnel constructed in the system. The tunnel is a 2200-ft (670 m) twin-bore section, designated Contract A-2, in downtown Washington. Two objectives of this program were to determine the relationship of construction procedure to settlements and to observe the pattern of soil movement around the tunnel as an aid in evaluating underpinning criteria for nearby structures. A test section, consisting t three instrument lines located across the tunnel path, was established prior to mining in Lafayette Park to measure in detail both vertical and lateral soil displacements as the tunnel was mined through the section. The site was selected because it is free from surface structures and access for installation and reading of the instruments was convenient. Load and distortion measurements on the lining were also made within the test section; observations of construction procedure were maintained throughout construction.

Jan 1, 1997

By K. C. Mills, E. T. Turkdogan

A number of investigators1 6 have noted the presence of a liquid miscibility gap in the Fe-Sn binary system. However, the first attempt to measure the

Jan 1, 1964

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

For the past four years, the Department of Mining Engineering at the University of Kentucky has conducted a validation study of the CFD Fluent code, by comparing its results against mining-related benchmark experimental data provided by NIOSH?s Pittsburgh Research Laboratory. This particular study is dedicated to the effect of machine-mounted dust scrubbers on the performance of face ventilation systems using extended-cut mining with a blowing curtain.

Jan 1, 2009

By Curtis Wilson

FROM the results of his investigation of the hardenable copper-nickel-silicon and copper-cobalt-silicon alloys, M. G. Corson1 explained the dispersion-hardening effect by assuming the precipitation of the inter-metallic compounds nickel silicide and cobalt silicide, and on this basis he constructed diagrams for the pseudobinary systems copper-nickel silicide and copper-cobalt silicide. A consideration of these diagrams and of the factors that exert such an important influence upon the rate of precipitation, such as degree of supersaturation, nucleus number and rate of diffusion, leads to the expectation that the rate of precipitation of the silicides on reheating the quenched solid solutions at temperatures below the alpha-phase boundary should increase continuously as the reheating temperature is raised. The present investigation shows that while this rate does increase with the reheating temperature in a general way, it does not do so continuously. Supplements to Corson's diagrams are offered, showing the discontinuities, and slight modifications in the solubility curves are suggested.

Jan 1, 1933

By K. Richardson

Although the De Beers group has a long history of placer mining on land, the group only became actively involved in deep water marine diamond exploration and mining in 1983 with the formation of DeBeers Marine. Full-scale commercial mining commenced around1991. Since then, the group marine mining capability has grown into a formidable fleet of 8 large deep water (>70 m) mining vessels, as well as other special purpose geosurvey platforms. Marine diamond production by the group is expected to be just short of 1 million carats in 2006. De Beers operates across the entire value-chain spectrum from geology and geosurvey, through sampling to mining, and finally ore processing into high value concentrate. Supporting these operations involves significant service activities such as maintenance, security, logistics and environmental management. Specific challenges exist in terms of developing or acquiring appropriate technology for marine mining. These challenges have resulted in De Beers operating extensive in-house R&D and projects departments, as well as drawing extensively from technology partners. An array of computational and test facilities is also available to support R&D and projects activities. Hydrotransport in various guises is key to the current approaches to marine mining and ore processing. Use is made of airlift and centrifugal pumping for hydraulic hoisting of very coarse gravel, while splitters, launders, dewatering, elutriators, jet pumps, centrifugal pumps, dense medium circuits, pipeline systems, and instrumentation for coarse abrasive particles are used extensively in the ore processing plant.

Jan 1, 2007

By Robert Rother

El presente texto señala el proceso de exploración y preparación que anteceden la etapa de la producción de mina. Para ello, es necesario ubicar un depósito mineral donde se clasifican en vetas, zonas de cizallamiento, contactos, substituciones y diseminaciones, que se distinguen por la forma de la zona débil en la costra terrestre. Asimismo, es necesario anotar datos como: ubicación, acceso, altura sobre el mar, características de la región, labores, posición del cuerpo mineralizado, sobrecarga, caja y ganga, tectónica y todo lo que se puede ver efectivamente. Posteriormente se evalúa el título de las propiedades, mapeo topográrico y geológico del yacimiento, sistema y costo del muestreo planeado, estudio de las vías de acceso y transportes, reservas de mineral, así como considerar el programa de producción (abastecimiento de agua, mano de obra, escala de operación, tratamiento metalúrgico, valor de la producción, costos de operación, utilidad de operación).

Jan 1, 1964

By Don Phelps, Dean Brox, Peter Procter, Andy Saltis, Tom Morrison, Jeff Pringle

The Greater Vancouver Water District is currently constructing the Seymour-Capilano Water Filtration Project to enhance the quality of drinking water in the Vancouver metropolitan area. The Seymour-Capilano Water Filtration Project comprises the 1,800 million litres per day Seymour-Capilano Filtration Plant, the 1,080million litres per day Capilano Pumping Station, twin tunnels with associated shafts, and the Capilano Energy Recovery Facility. The twin tunnels will convey raw water under pressure from the Capilano Reservoir to the Seymour Filtration Plant and return treated (filtered) water for distribution. The Twin Tunnels component of the project comprises twin, 3.7 m diameter, 7.2 km TBM bored tunnels, the 180 m deep Seymour Shaft as the main launch shaft, and two 4 m diameter, 268 m deep raise bore exit shafts at Capilano. The Twin Tunnels have been planned as predominantly unlined tunnels sited at depth entirely within granitic bedrock and cross under two major buried glacial valleys of breadths in excess of 1500 metres that are filled with glacial sediments to depths up to 200 metres. The maximum overburden along the tunnel alignment is approximately 400 metres. Comprehensive site investigations and studies were completed during the detailed design stage of the project. The construction of the twin tunnels started in the fall of 2004 and is planned to be completed by mid-2008.

Jan 1, 2005

By David C. Lager

While not a new construction technique "top/down" construction is seeing increased use in high rise building construction. Using diaphragm wall, drilled shaft and mining construction techniques, top/down construction enables construction of both the below grade basements and high rise structure simultaneously. To date the top/down method has been used on at least four major building projects in the United States. This paper will review the economic, engineering, construction and schedule issues associated with top/down technology on two projects -Olympia Centre, Chicago, and One Westwood, Los Angeles. Top/Down construction is currently under consideration on several additional projects in the United States.

Jan 1, 1987

In 1961, West Australian Petroleum's Eneabba No. 1 bore encountered 22 seams of coal totalling 40 ft in thickness between the depths of 6373 ft and 6441 ft. On analysis, this coal had a similar calorific value (8000-HOOO B.T.U./lb, assuming 20 per cent water) to the coal from the Collie Coalfield, Western Australia's only known area of commercially exploitable coal. Being buried to depths in excess of 6000 ft, the coal at Eneabba had developed weakly-coking properties, and thus, although much younger than the Permian coals of Collie, gave promise of being a major potential source of power for Western Australia.West Australian Petroleum undertook a programme of stratigraphic drilling and shallow test drilling to determine whether this coalhorizon persisted into the outcrop of the Lower Jurassic sediments in the Hill River district, 140 miles NNW. of Perth, and, if it was present, if the quality and quantity of the coal would warrant development of the deposits by open cutting. The coal horizon was identified in the near surface, but the poor quality of the coal and the complexity of the structure made development (in the area examined) uneconomic at the time.A strong seismic reflection in the Eneabba area occurs at the same depth as the Jurassic coals. This event originates within the upper beds of the Lower Jurassic and it is probable that the velocity contrast between the higher velocity siltstones and the very low velocity coals enhances this very strong, distinctive seismic reflection.This event can be followed on continuous seismic data over a large area of the northern Perth Basin, from 13 miles SE. of Dongara to 20 miles SW. of Coorow. It can be followed from a depth of 4000 ftnear Dongara to over 17,000 ft to the SE., so development of thisvast potential source of power will depend on the economics ofprocesses being developed for the production of power from theburning of coal seams in situ.INTRODUCTIONThe discovery of 22 seams of economically useable coaltotalling 40 ft in thickness in the Lower J urassic sedimentsof the Eneabba No. 1 bore (Fig. 1) led to the search forthese seams at economically workable depths. The Ministerfor Mines in Western Australia granted to West Australian1. Supervising Geologist, West Australian Petroleum Pty. Ltd.Manuscript received at The Institute, 25th May, 1964. and presented to the 1964Annual Conference.

Jan 1, 1964

By M. Rufli

Until not so long ago most ring geared mills were operated with fix speed motors only. By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The sophisticated operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore utmost availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives. Now this paper is focusing on the experiences gained with this kind of sophisticated ring geared mill drive system rather than only show and explains the operational benefit of the different functions. Several measurements of different operating conditions, starting, frozen charge remover, controlled roll back, backlash, etc., made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. The accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.

Jan 1, 2011

Simulation and Analysis of Media Behaviour in the Tower Mill by Discrete Element Method for Estimating the Power Draw and Spatial Distribution of Grinding Process The trends to the Tower Mill (TM) for grinding the materials are increased recently due to its unique merits. Among the various considerations of this machine, the main important items are increasing the efficiency of grinding as more as possible while keep the power consumption, manufacturing and maintenance costs as less as possible. Because this grinding process includes a huge numbers of media particles (ball or other shapes) that are interacted with each other and body of the machine, the DEM (Discrete Element Method) way is a very useful and essential step to getting confident evaluations. Because the DEM simulation is a very young scientific field and proper commercial software are very rare and still under modification, at first step, a FORTRAN code is developed for DEM simulation of two laboratory Tower Mill models (KM5 and KD5). The simulation and experimental results matched each other properly. Then one another DEM software was implemented to perform simulation of bigger models (huge numbers of balls), meanwhile could handle the complex 3D geometry data. The simulation and experimental results were compared and analysed in detail for not only laboratory but also for industrial models (KW5, KWD5, KWD50, KW300F, KW700F and KW1500) without any manipulation or compromising of the parameters of simulation. Some numeric data of industrial models are hidden here due to confidential reasons. The relative velocity of balls (ball-ball and ball-TM body), dissipate energy, interacted forces and stresses during the process are the key outputs of DEM simulation for design this machine. Therefore the main important processes in a Tower Mill machine are recognised and consequently some horizons of development of this machine are distinguished.

Sep 13, 2010

[ ]

Jan 1, 2008

By J. Searra, M. Aboagye

"For new mining projects or for medium- to long-term areas of existing mines, drilling data is invariably on a relatively large grid. Direct estimates for selective mining units (SMUs), and also for much larger block units, will then be smoothed due to the information effects and the high error variance.The difficulty is that ultimately, during mining, selection will be done on the basis of SMUs on the final close-spaced data grid (grade control), which will then be available, i.e. the actual selection will be more efficient, with fewer misclassifications. However, this ultimate mining position is unknown at the project feasibility stage and therefore has to be estimated. This estimation is required because any cash flow calculations made on the basis of the smoothed estimates will obviously misrepresent the overall economic value of the project, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the average grade of the orebody. Similarly, unsmoothed estimates will be conditionally biased and will give even worse results, particularly in local areas of short- and medium-term planning or mining.This paper presents a case study of indirect post-processing and proportional modelling of recoverable resources designed for mediumand long-term mine planning at the Gold Fields’ Tarkwa Mine in Ghana. The case study compares long-term indirect recoverable mineral resource estimates based on typical widely spaced feasibility data to the corresponding production grade control model as well as the mine production. The paper also proposes certain critical regression slope and kriging efficiency control limits to avoid inefficient medium- to longterm recoverable estimates, and highlights the danger of accepting block estimates that have a slope of regression less than 0.5."

Jan 1, 2015

By Matthew I. G

A new process for leaching zinc sulphide concentrates with gaseous mixtures of SO2 and O2 in aqueous solution is described.The reaction of SO2/O2 with Rosebery, Mt. Isa, Broken Hill and Elura zinc concentrates yields zinc and iron sulphates, elemental sulphur and some sulphuric acid. Rates of zinc extraction are controlled by a surface chemical reaction without apparent interference from the elemental sulphur layer for SO2 concentrations up to 9 per cent in the gas phase. Pyrite in concentrate exerts an activating effect, possibly through galvanic interaction with the sphalerite. Metal extractions are dependent on SO2 and O2 tenors of the gas, particle size, and the acidity and zinc content of the solution, but are independent of the ferric ion level. Extractions also reach maxima at about 85°C.Generation of acid may be prevented by conducting the reaction in the presence of ferrous iron and at acidities of 40 g/l or greater. Zinc and iron levels in Elura lead concentrate may be reduced by leaching with SO2/O2.

Jan 1, 1981

By Garry Johansen, Andrew McCallum, Sandy Gray, Gary Patrick, Jennifer Abols

"The authors challenge the traditional thinking that whole ore cyanidation followed by Carbon in Pulp (CIP) or Carbon in Leach (CIL) should be applied as a standard process in the majority of gold processing flowsheets. The concept of whole ore leaching by using cyanide can result in unnecessary environmental and capital risk. Alternative, currently available technologies can be used to provide the desired level of gold recovery at a much lower installed cost and less impact on the environment. Gravity concentration, alone or in conjunction with flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit.The InLine Leach Reactor (ILR) is an intensive cyanidation unit developed by Gekko Systems of Australia. Advantages of this technology include significantly reduced capital outlays for greenfield plants or plant upgrades and increased investor returns. Reduction of onsite cyanide and carbon inventories improves plant safety, materials handling and site security. By using direct electrowinning to treat the gold bearing solutions produced by the ILR, the need for a conventional carbon stripping circuit is removed. Potential also exists to increase grind size – saving energy, further reducing capital and operating costs and decreasing the environmental impact of a mill. Detoxification of cyanide before the release of solution to the tailings dam can minimise tailings disposal and containment requirements.When used in the right application the proposed process will have little or no impact on gold recovery and may actually increase recovery for complex ores. Areas applicable to this type of treatment include: plants in environmentally sensitive regions, lower tonnage higher grade deposits, coarse gold deposits, and preg robbing ores - some of which may not currently be economically feasible using standard processes and flowsheets. We have provided three examples of such projects, where an alternative to whole ore leach and CIP or CIL has delivered these benefits."

Jan 1, 2003