Search Documents

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

By L. J. Cunningham

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By C. H. van Eendenburg

"Installation of a 3.6 km long raw coal conveyor in the Balmer open pit was undertaken to improve over-all haulage efficiency. This paper covers the rationale behind this project, system design and construction aspects and initial operating experiences. The majority of the construction work was performed by our own personnel. Where feasible, used equipment was installed to reduce capital cost and facilitate a tight construction schedule.BackgroundWestar Mining Ltd's Balmer Mine is located in the British Columbia Rockies, just outside of the town of Sparwood in the southeastern corner of British Columbia. The open pit mine, which has been in operation since 1969, currently produces about 6 million clean tonnes of coal per year, mostly for the metallurgical coal export market. Run-of-mine coal tonnages total between 9 and 9.5 million annually and waste removal volumes exceed 30 million bank cubic metres.The mine is a truck/shovel operation; loading equipment includes nine electric shovels, five front-end loaders and a hydraulic backhoe. The truck fleet consists of 40 units of 154-tonne, 181-tonne and 315-tonne capacity. The newer 154-tonne trucks are used for coal haulage for which they have been equipped , with tailgates to maximize their coal carrying capacity."

Jan 1, 1990

A consideration of mining ventures and the changes of an environmental nature that occur. The paper is introduced with a general statement claiming recognition that mining ventures are important to human well-being but that these need to be justified against the environmental changes that they bring about. The various factors that need to be considered are cited followed by an historical review of mining activities. The various environmental issues are discussed under three headings; socio-economic, physical and biological, prior to reviewing the world's demand for minerals including fossil fuels. In conclusion guidelines for appraising mining ventures relative to environmental changes that may occur, are given.

Jan 1, 1981

The stability of parallel underground coal mine galleries and pillars have been investigated using two- and three-dimensional (3D) numerical stress analysis. Anisotropic horizontal in situ stresses and the direction of the excavations have been considered in the numerical analysis. The stability of the tunnels driven in a coal seam at various working depths has been investigated taking into account different strata conditions and then results from two- and three-dimensional numerical modelling studies were compared. Maximum principal stress components have been chosen in three various directions: vertical, parallel and perpendicular to the tunnel axis. Analysis have shown that in the anisotropic in situ stress field, the favourable direction of underground mine openings which have different strata conditions depend not only on the horizontal in situ stresses but also on the vertical in situ stresses. Furthermore, 3D numerical modelling studies have been carried out to investigate stability of multiple entry longwall panel gate roads and pillars with various width-to-length ratios (W/L). Results of the modelling studies have shown that the critical dimension of coal pillars depends on their width and the direction of maximum horizontal stresses.

Dec 6, 2010

Grade control is a real challenge, and better sampling and modelling practices are among the tools that have proven efficient in improving it. Although based on rather trivial examples, this paper addresses the following important issues: How much of a challenge is it? How and to which degree can it be improved? And what kind of economic benefits should be expected in return for the corresponding efforts?

Jan 1, 1999

By Dean Bray

During the past three years, a new rear-dumping dragline bucket technology has been patented, developed and tested at North Dakota coal mines. Field testing has shown that this new concept in dragline bucket technology can improve strip-mining efficiencies by reducing cycletimes and increasing dumping radius. This article details the process, participants and the results for the development of a rear-dumping dragline bucket. Participants in the process In November 1995, the board of directors of Dakota Coal authorized the execution of a field test and option agreement and a license agreement with the partnership of D.F. Schmidt, electrical/maintenance supervisor, and Bill Lengenfelder, president of Modern Industrial. The board also authorized entering into a dragline bucket field-testing agreement with the Falkirk Mining Co.

Jan 1, 1999

By Holmes R. J, Miles J. G

An on-stream shale detector has been developed that is suitable for use on conveyor belts carrying iron ore of up to 200 mm particle size. The shale is distinguished from high-grade iron ore by means of the substantially greater total natural gamma-ray activity (400-3000 keV) of the shale, which is due to the presence of uranium (214Bi), thorium (208TI) and potassium (40K). Other gangue materials, sueh as highly siliceous cherts and jaspilites, escape detection because of their low activity. A dynamic trial of the shale detector at Mt Whaleback, using a large-volume (100 × 100 400 mm long) "Polyscin" Nal(TI) gamma-ray detector, demonstrated that as little as 20 tonne of ore on a conveyor belt (equivalent to partial truckloads of ore) can readily be monitored for shale content.

Jan 1, 1981

By Wilbert J. Huff

The work of the Explosives Division, Bureau of Mines, United States Department of the Interior, for the fiscal year ended June 30, 1939, is described in the following pages. This paper is the fourth of a series of annual reports covering the activities of the division since July 1, 1936. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders to whom specific credit is indicated.

Jan 1, 1940

By T. R. Marshall

SAMREC (The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves) Clause 7 notes that ‘Documentation detailing Exploration Results, Mineral Resources and Mineral Reserves from which a Public Report is prepared must be prepared by, or under the direction of, and signed by a Competent Person.’ Similar statements with respect to Competent Valuators (CVs) and Qualified Reserves Evaluators (QREs) are contained in the SAMVAL (South African Code for the Reporting of Mineral Asset Valuations) and SAMOG (South African Code for the Reporting of Oil & Gas Resources) codes respectively. What does it mean to be a Competent Person (CP) in the context of compiling/signing-off on SAMCODE (South African Mineral Code) compliant documents? What do the registration and experience requirements mean? Who is ultimately responsible for the report and what does such responsibility prescribe?

Sep 1, 2021

It is difficult to evaluate exploration properties in a manner that is transparent, repeatable and easily re-calculated to cater for different geological interpretations, but the risk-based assessment methodology, the Geological Risk Method, developed and described by Lord et al (2001) attempts to satisfy all these criteria. This paper examines a case study example based on valuations of exploration projects conducted by SRK Consulting using this methodology, and describes some of the advantages and limitations of the method.

Jan 1, 2007

By Donald B. Gillies

THE great source of iron ore for the furnaces of this country has been the Lake Superior district. Ore was first discovered there in 1844, and the first shipments made via the Great Lakes in 1852 to a furnace at New Castle, Pa. The stream of ore from that region increased slowly to exceed a million tons in 1873, and did not reach 10 million tons until 1895. By 1901 it exceeded 20 million tons, and in 1907 over 40 million tons. Total Lake Superior output through 1948 was about 2500 million long tons. Outside the Lake Superior district are the Southern district, including mainly Alabama, Georgia, Missouri, and Texas; the Eastern district of New York, New Jersey, and Pennsylvania; the Western district embracing Wyoming, Utah, and California.

Jan 1, 1949

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) is a new method to apply bi-directional loads to a deep foundation element with the loading source located above the foundation head. In the TLBT reusable load assembly, loads are applied to the foundation using the R-System which consists of two stacked steel plates located at the geotechnical resistance balance point or at the foundation base connected to the load assembly via vertical elements. The top plate or the Shaft Bearing Plate (“SBP”) will transfer loads to the foundation upper portion, and the bottom plate or the Base Bearing Plate (“BBP”) will transfer loads to the foundation lower portion as well as the foundation base. At the surface, above the foundation head, a hydraulic jack is located between a Top Load Assembly (“TLA”), and the Bottom Load Assembly (“BLA”). The TLA and BLA are connected to vertical elements which are consequently connected to the R-system. As the jack is pressurized and expanded at the surface, the R-System plates are separated, and the foundation is bidirectionally loaded. This paper presents a brief description of the conventional Bi-Directional Load Test (“BDLT”) including benefits and limitations followed by the TLBT method introduction including its benefits and advantages over other testing methods.

Sep 8, 2021

By Lytman Jordán

En la actualidad, el proceso de Ore Control de Tintaya se convierte en un reto porque la naturaleza del yacimiento Metasomático de Contacto Tipo Skarn presenta una mineralización compleja a manera de pasas en una torta. En ese sentido, la cultura Sigma -que presenta poderosas herramientas estadísticas y de gestión de procesos-, logró conceptualizar el proceso de ore control e identificar y optimizar tres sub-procesos críticos: el muestreo de Blasthole, preparación y análisis de Muestras de Blasthole y el Ore Control Operativo. Por ello, el presente texto señala la optimización del oro control de Tintaya a través de la metodología Six Sigma, donde se logra mejorar el proceso desde el muestreo de blasthole hasta el envío de mineral a las plantas, se minimiza los eventos de fuga de mineral a los botaderos y con la data confiable de los blasthole, se elaboran modelos de corto plazo que permiten generar planes predecibles de minado.

Sep 9, 2007

By Gabriel Gonçalves Pessoa de Castro

O trabalho teve por objetivo produzir uma liga Al AA1070 com granulometria fina a partir de um material com granulometria grosseira, por meio de deformação plástica severa (DPS) aplicada por prensagem por canais equiangulares (ECAP) via rota C, bem como esclarecer e avaliar os mecanismos responsáveis pela evolução microestrutural durante este processo de prensagem. O processo empregou a rota C com 5 passes consecutivos a frio e acumulou uma deformação ?5 = 5,95. O material de partida é proveniente de um processo de laminação a quente, com uma microestrutura de grãos grosseiros com tamanho de grão de 16 ± 18 µm. Foi realizada a caracterização microestrutural com o auxílio das técnicas de microscopia eletrônica de varredura (MEV) e de difração de elétrons retroespalhados. O refinamento microestrutural foi realizado eficientemente alcançando uma microestrutura fina, observou-se uma redução de 80% alcançando um tamanho de grão de 3,38 µm, e um aumento da fração de contornos de alto ângulo passando de 23% a 46%. A partir dos resultados obtidos nas análises conclui-se que os mecanismos responsáveis pela evolução microestrutural foram os processos de subdivisão por meio de fragmentação e rotação de grãos, recuperação e recristalização dinâmica.

Aug 16, 2017

"These tentative coal mine inspection standards have been prepared as a guide for the Federal inspection of coal mines of the United States. Much time and thought have been spent by various members of the Safety Division in the preparation of thses standards, and it is believed that compliance with them eventually will be possible in most mines. In many instances objections will be raised to them owing to long-established mining customs and practices that are inherently of dubious safety and to a natural inclination to oppose change. In other instances there will be valid objections due to conditions not foreseen at the time these standards were prepared. Or there may be substandard conditions and practices due to original mine layouts that it is not practicable to change during the lifetime of the mine; in such instances it is likely that some effective measures are or can be taken toward lessening hazards.With the rapid change in mining methods some of the standards may become inapplicable and it may be advisable to revise them to meet the new conditions. Therefore, questions regarding these standards and suggestions regarding new standards should be brought to the attention of the supervising engineer of the Coal Mine Inspection Division so that modifications of and additions to these standards may be made from time to time.In many respects these standards exceed the provisions of the various State mining laws, and some may conflict with the laws of some States. In cases of conflict, the intent is not to advocate noncompliance with State laws but to suggest that it may be desirable for the State to reconsider such laws or safety orders.Although an effort has been made to word these standards so that they may be readily understood, nevertheless, a reasonable interpretation should be placed upon them. In fact, in numerous instances the words reasonable"", ""suitable"", and ""properly"" are used in recognition of the fact that reason- and sound judgment enter into the carrying out of the safety endeavor.The policy of the Bureau on some vitally important safety matters in mines is set forth in its published Safety Decisions. These decisions have been consulted and used in the preparation of these standards. These decisions also are now being reexamined by its Mine Safety Board."

Feb 1, 1942

By F. Hashiuchi

In 1996, the Saganoseki custom smelter & refinery successfully shifted to a single flash smelting furnace operation and increased the copper production capacity to 450,000mtpy in 1998. As the next step, Saganoseki planned to further increase the productivity, especially in the area of P.S. converters and acid plant. As the results of modifications and operational improvements, the gas washing & cooling sections of the Saganoseki acid plant were consolidated from 3 to 2 lines, and increased the gas treatment capacity. The S02 converters in the acid plant were also modified to increase the acid production. By increasing the matte grade from 65 to 68%, six PS converters have been successfully integrated into four, while maintaining the production capacity and reducing the environmental burden in 2005. This paper discusses recent operational conditions and the results of implementation of technological improvements.

Jan 1, 2007

By W. E. Roscoe, H. Agnerian

The contour method can be used to estimate the mineral resources of a mineralized body. It relies on geological interpretation and allows the geologist to determine the plunge of a mineralized ore shoot along the dipping plane of the mineralized body. The technique is best applied to estimate tonnage and average grade of relatively planar bodies, i.e., where the two dimensions of the mineralized body are much greater than the third dimension, such as Archean lode gold vein deposits or mantos of massive sulphide mineralization, based on exploration drilling. For these types of deposits, the contour method can provide a clear view of the “mineralization landscape” with “peaks” and “valleys” along the plane of the mineralized vein. The technique also reduces the “nugget effect” of local high values commonly present in gold deposits. With sufficient drill hole information, the contour method may be used to estimate the tonnage and average grade of individual blocks within a mineral deposit. General procedures for the contour method are described in this paper, along with examples and explanatory notes.

Jan 1, 2002

By H. F. Yancey

The investigations described in this bulletin are confined to a study of the washing characteristics of bituminous coals. The major part of the work was conducted by the Bureau of Mines in cooperation with the Engineering Experiment Station of the University of Illinois and the State of Illinois Geological Survey Division between 1918 and 1924, in accordance with the provisions of an agreement between these agencies. The washing characteristics of coals from many of the important coal-producing fields of the Eastern and Central States were examined. The coals of the Pacific Northwest States and Alaska have been studied separately by McMillan and Bird of the Northwest Experiment Station of the Bureau of Mines at Seattle in cooperation with the College of Mines of the University of Washington.2 OBJECT OF INVESTIGATION The object of the investigation of coal preparation by the Bureau of Mines has been to promote the production of better prepared coal and to facilitate the correct selection and design of coal-preparation plants by obtaining as complete information as possible regarding the washability of the various types of American coals and the treatment best suited to each. In addition, some attention has been given to the development of new methods of washing coal. The work naturally divides itself into three rather distinct steps: (1) Development of a systematic method of examining and testing a coal; (2) classification of the American coals on a basis of the occurrence of the impurities associated with the coal in the beds; (3) examination of one or more representative coals of each type.

Jan 1, 1929

By Bruno KERL

THE list of deaths reported during the year 1905 comprises the following names (the figures in parentheses indicating the year in which the persons named were elected to membership:- Honorary Member.-Dr. Bruno Kerl. Members and Associates.-Charles Christy Adams (1903), John Wesley Anderson (1898), William Burton Barber (1901), Thomas A. Bennett (1900), Luke W. Bryan (1901), Edwin S. Daugherty (1905), William Scott de Camp (1875), George H. Eldridge (1889), B. W. Frazier (1871), John Broome Guinn, Jr. (1897), Dana C. Irish (1900), Harry Hugh Lee (1899), William Alfred Lindsay (1902), Roland C. Luther (1884), James MacNaughton (1890), Gordon McLean (1899), Herbert Holmes McNamara (1902), August R. Meyer (1886), William Orr (1897), William J. Parker, Jr. (1898), Joseph Phillips, Jr. (1895), Charles O. Ripley (1902), Emmerich J. Schmitz (1883), Ludwig Philip Seeger (1900), Jacob Johnston Sperry (1900), Gustavus H. Stoiber (1902), William L. Study (1905), Robert Macnair Wilson Swan (1900), Richard Henry Terhune (1886), Joseph Thiry (1892), John N. Tisdale (1903), Alfred Isham Totten (1897), Walter H. Virgoe (1902), Charles H. Wellman (1890), Harvey L. Williams (1903). Of these, Dr. Bruno Kerl and Prof. B. W. Frazier have been made the subjects of special Biographical Notices in the Bi-Monthly Bulletin 1 the former in No. 4, July, 1905, p. 743, and the latter in No. 5, September, 1905, p. 1097. Concerning the remainder of the list, the following paragraphs comprise such information as could be obtained by the Secretary. Charles Christy Adams, who had been a member of the Institute since 1903, died in Johannesburg, South Africa, August 31. 1905. He was born in New York City, July 13, 1849, and received his technical training at the Colorado State School of

May 1, 1906