Search Documents

By MUSTAFA ERKAYAOGLU, ENVER YILMAZ

Coal mining is likely to sustain its critical role as energy requirements are increasing. While surface mining exploits coal seams near the surface, underground mining techniques are crucial for extracting deep coal reserves. Longwall mining is one of the most common methods used in underground coal mining operations. This paper introduces a data-based framework — including data collection, data analysis and the interpretation of operational data — for understanding the system efficiency of a longwall shearer. Operational performance is evaluated by the time between arrivals (TBA) and duration of the shearer stoppages, shearer drums’ reversal time, cutting speed and flit speed on daily production in a longwall top coal caving (LTCC) mine. A discrete event simulation model is developed to represent the bidirectional cutting sequence of a longwall shearer.

By D. S. Robertson

More than 700,000 feet of diamond drilling was completed in the Blind River area between 1953 and 1958. Much of this drilling was at depths which are still not usual in North America. However, as the tendency is to deeper holes, factual data from the Blind River operation may well provide information of value in future programs. Rates of drilling decreased with in-creasing depth, but uncommonly good rates (an average of over 50 feet per day over more than 4,000 feet of hole) were achieved with proper engineering and care. Costs varied as contractors and geologists became familiar with the area Hole deviation in the Blind River area was locally severe and control of the hole trace became a major problem. Careful surveying was necessary and found to be highly re-liable. It was found that control of the hole trace above 1,500 feet was much more difficult than at depths below 1,500 feet. This is explained by the mechanics of the drilling operation. Various methods of controlling hole deviation were attempted and,

Jan 1, 1962

By Dimitrios Polantzas P. E., Collin E. Sweeney E. I. T., Franklin M. Grynkiewicz P. E., Leili Javidanian P. E.

In the latest AASHTO design specifications, the Load and Resistance Factor Design (LRFD) method is prescribed for the design of retaining walls. However, inconsistencies arise when LRFD is used for retaining wall design versus the traditional Allowable Stress Design (ASD). Required toe embedment and wall loading demand vary greatly when the two design approaches are compared, all else being equal. This is due to application of linear load factors to properties that vary non-linearly in the design. These inherent inconsistencies are further intensified when introducing factors such as layered soil profiles, different wall types, groundwater elevation, and surcharge requirements. When applied correctly, these two design approaches, in theory, should lead the designer to the same result with little discrepancy, as they do with steel structure design. However, the use of the current AASHTO LRFD method for various geostructural retaining wall designs yields contradictory results that suggest existing retaining walls that have been successfully designed and constructed are unstable. Fundamentally, LRFD should be built on reliability-based calibrations; the successful past performance of existing retaining structures designed using ASD suggests that the LRFD approach requires considerable modification. The authors of this paper recommend that the current LRFD load factors be reviewed and revised based on more comprehensive wall performance data and wall type such that the difference between retaining structures designed using LRFD and those designed using ASD is eliminated.

Oct 1, 2022

By William J. Almas

Operating uranium mill tailings containment and mill decommissioning activities are regulated by the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA) through numerous regulatory mechanisms. Reduction of radon emissions from tailings disposal areas, remedial actions to return groundwater to baseline constituent concentrations, and 200-to 1,000-year stabilization of tailings are major focus areas of regulation. The cumulative economic impact and uncertainty associated with regulation are very significant and will hinder future development of uranium milling facilities.

Jan 1, 1991

By James F. Howe

Modern civilization is centered around a small group of essential occupations, the three principal ones which are agriculture, mining and manufacturing. Agriculture might be called the most important of the three, as it has to do directly with the supply of food for the human race. Mining, however, is certainly next in importance, as it furnishes the supply of fuel and many of the raw materials used in manufacturing. Without mining, modern machinery and many industrial operations would be impossible. Mining takes advantage of the, natural resources in fuel and minerals that lie underneath the surface of mother earth, and while at times some of these metals are hard to find and mines come and go, mining must continue to increase. Mining is no longer a haphazard proposition but one calling for careful study and complete plans of operation for years to come. The shafts, power houses, rock dump crusher, concentrator, and other machinery must be located advantageously in order to enable owners to make a profit. Many tons of rock or mineral must be mined frequently to get one ton of concentrated metallic ore or metal itself. Economy in mining is just as essential as it is in manufacturing. The mining engineer of today is called upon to utilize every branch of engineering, and not only, is a wide: range of knowledge required, but ingenuity to meet the unusual conditions which are constantly arising from week to week. On account of the wide variety of information required by the mining engineer, some things with which he is in almost daily contact may be passed over with only a small amount of attention, provided everything is going well, in order that time and attention may be focused on what might be termed the more important features of mining operations. Because competition has become keener than ever, owing to overproduction at times of certain minerals, it becomes a matter of first, importance to understand as far as possible the factors which enter into the cost of production of any mineral which may be mined. In such times of overproduction, the high cost mine is forced to close down while the low cost mine may, if desired, be kept running constantly. In keeping a cost record, wire rope on account of its high first cost 19 coming into the lime light, and a comparison of records of one mine with another is now frequently made in order to see whether the rope service is satisfactory or not. Every rope maker, on the other hand, is interested in seeing that the rope which he produces gives the maximum possible return for the money invested. Modern mining owes much of its success to the use of wire rope for hoisting materials from beneath the surface of the ground. Deep mining would be impossible without the use of wire rope as a means of hoisting. A study, therefore, of rope problems in mining work and a discussion of the points which are beneficial to maximum life will enable the mining engineer, manager, or superintendent to keep his costs down to the minimum while at the same time he provides a suitable and sufficient safety factor for operations at all times. Mining might be defined as the extraction of coal, metallic ores, or minerals from below the surface of the ground. This definition does not cover what is known as, open pit operations or quarrying but covers the

Jan 1, 1922

By Russell Frith

The entire subject area of micro-seismic events due to stored strain energy, as distinct from gas-driven coal outbursts, can be readily sub-divided into firstly events with their energy source from within the coal seam (termed “bursts”) and secondly, event with their energy source outside of the coal seam in either the overburden and/or floor strata. The reason for sub-dividing micro-seismic events in this manner is that if the causation mechanisms and associated geotechnical conditions are materially different, then effective pre-mining predictions and subsequent operational controls may also differ. Attempting to explain a multitude of micro-seismic event types without consideration of varying source mechanisms will inevitably lead to inadequate causal explanations and effective controls.

By E. Farrokh

CSM and NTNU models are among the most commonly used models in TBM performance evaluation. Due to increasing application of TBM in different tunneling conditions, modification became necessary for these models. Sensitivity analyses on these two models indicate that both models are very sensitive to machine characteristics. Analyses performed on CSM database for cutter load and penetration rate prediction indicate while the r-square of the CSM model is reasonably high for the predicted cutterload, the r-square value for the penetration is low. In order to increase prediction capability of CSM model for penetration rate the model was reevaluated using non-dimensional analysis and the original database of Colorado school of mines. NTNU model is evaluated using Monte Carlo simulation and regression analysis. The results of analyses indicate that the majority of the variation of the penetration in NTNU model can be explained by only three parameters. This might indicate that the effects of other factors are overshadowed and it is worthy to reevaluate NTNU model using original database and more updated statistical methods to avoid overlapping of different parameters correlations.

Feb 23, 2014

By Lei Fu

In the wake of the collapse of the ceiling panels in the I-90 section of the Central Artery/Tunnel (CA/T) Project in 2006, the long term performance of tunnels became the focus of the tunneling industry. At the time of the accident, the tunnel had been open to traffic for about 10 years. This paper will discuss design methods and considerations to improve the long term performance and durability of a tunnel. The major problems found during the inspection of several tunnels will also be presented and the causes for these problems will be discussed.

Jan 1, 2008

By Suresh Sundarraj

A diffusion mass transport model for predicting the microsegregation in a solidifying and coarsening dendritic mushy region of a binary alloy is presented. Two versions of this model are tested; one based on expressing the solute concentration in terms of mole fraction and the other on expressing the solute concentration in terms of mass fraction. On comparing previous model data sets and conditions, used in the analysis of Aluminum-Copper systems, a number of inconsistencies emerge. These inconsistencies are resolved on identifying a single set of data and conditions which take account of compositional density changes, "non-linear" thermodynamics and dynamic coarsening. An additional investigation is carried out to study the effect of assumed cooling mechanisms.

Jan 1, 1992

By E. Farrokh

Estimation of the cutter life and cost is a part of evaluating performance for a hard rock TBM in any project. Various approaches has been proposed for calculation of disc cutter life in various rock types based on machine specifications and rock strength and abrasivity. Cutter change time is a parameter that is used in some of the estimates and is defined as the average time required for changing a cutter on the cutter head and cutter life is the number of cubic meters of excavated rock per each disc cutter. Analysis of cutter life information of several tunnel projects from around the world has revealed that the published models for estimation of cutter consumption require some revisions to offer a more accurate prediction. The preliminary analysis of data shows that the average cutter change time is approximately 66 minutes for different cutter sizes and there is a minimal difference between corresponding cutter change times of the large (e.g. 19 or 20 in) versus smaller cutters (e.g. 15.5 to 17 in). This paper reviews the available and published cutter life data from various projects. It also introduces new models for estimation of cutter life and cutter change time as part of TBM down time and utilization analysis.

Feb 27, 2013

By Giuseppe Pintaude

The use of two-dimensional shape parameters to characterize abrasive particles is a possible approach to express their angularity. Nonetheless, in sliding abrasion, especially in pin abrasion testing, coated papers structure plays an important role and even its damage during the wear process should not be neglected. This manuscript discuss the limitations of two-dimensional shape descriptors in distinguishing wear caused by relatively hard particles, indicating that the wear data obtained in sliding abrasion tests are unable to distinguish different types of coated papers used when only the two-dimensional particle projection is considered for shape characterization.

Jul 31, 2018

By Kenneth N. Han, Peter Nam-soo Kim

A kinetic model for leaching of particulate metals in a batch system has been developed. The leaching mechanism has been analyzed by solving a series of ordinary differential equations relating heterogeneous reaction kinetics at the solid/liquid interface to mass transfer of reactant and products. Special emphasis has been given to the effect of changing of the surface area of the leaching substrate and initial particle distribution on the overall leaching rate. The dissolution of gold powders in acidic solution with bromine as an oxidant has been used as a model system. The effect of particle size, chemical reaction order, rate constant and mass transfer coefficient on the overall rate of dissolution of metal powder has been analyzed and discussed.

Jan 1, 2005

By K Schonert, K Eichas

Electrostatic separation of non-conductive materials can be accomplished by triboelectric charging. The efficiency of convential separators becomes worse in the size range below about 100 ¦m. These problems are solved by developing a new double-drum-separator. The investigations have shown the possibility of separating very fine mineral mixtures (eg quartz/calcite) in a strong electric field after tribo-charging in a special dust-feeder. The paper reports about the influence of particle size and field intensity on the separation and deals furthermore with the problem of desagglomeration.

Jan 1, 1993

By M. R. Anderton

"A hierarchical four-character code designed for geological and allied data may be used to log exploration drill-holes and store the information on magnetic media. The code is intended for use in semi-free format and permits the collection of as much, or as little, data as the geologist may require for the purpose in hand. A method of data storage by variable length records is discussed.Information may be retrieved by means of a simple enquiry language. Optional output facilities could allow the retrieval of data in a form suitable for direct input to a contouring package. The enquiry parameters and interrogation program can thus provide the interface between the data bank and associated application systems."

Jan 1, 2014

By Jacque Turgeon, Gontran Foy

"The Mineral Research Centre of the Quebec Department of Energy and Resources has worked extensively on the development of a dry process to extract pure mica flakes from a phlogopite ore. The liberation of mica from the gangue is effected basically by impact crushing, and the ground ore is screened into several fractions, each having a fairly narrow range of grain size. Each sized fraction is then fed to an air separator where heavy grains are separated from light flaky grains. Heavy fractions are returned to hammer mills where gangue minerals are ground finer and blocky mica particles are exfoliated. A second stage of screening is performed and each fraction is sent to an air separator. This sequence is repeated until mica products are virtually free of gangue. These different fractions are then treated in a cage mill in which mica flakes undergo a more orderly exfoliation along cleavage planes. The ground mica is again submitted to a final screening stage, after which each fraction constitutes a final commercial product.This process permits the recovery of about 70% of the mica contained in the ore. The over-all process will be described along with technical details of each unit operation. Recent work on a wet grinding method to produce very fine mica will also be discussed.IntroductionRecords of production of mica in Quebec date back to 1886. Production has been more or less continuous since that time, with peak activity during the war years. Production was interrupted in 1966, but started again in 1972 when Marietta Resources and Laviolette Mining and Metallurgical Corporation started their joint operation in Canton Suzor, northwestern Quebec. Mica deposits of more or less importance exist in different parts of Quebec, of which three have attracted attention in recent years: the Canton Suzor deposit, the Canton Lamy deposit and the Canton Chasseur deposit. The Suzor orebody was first identified by Carl Faesler in 1936, who described the rock as ""brown biotite in flakes half an inch in diameter, with interstitial augite, apatite and feldspar""."

Jan 1, 1982

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By Pete G. Kovalchik, Lynn A. Alcorn, Rudy J. Matetic, Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industries despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2002 show that 65% of the equipment whose operators exceeded 100% noise dosage is comprised of seven different types of machines. The continuous mining machine is first among all the equipment with 35% of the noise overexposures. The ational Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce excessive exposure for operators of continuous mining machines and preventing additional cases of oise Induced Hearing Loss (NIHL) by developing low-cost retrofit noise controls for mining equipment. This paper describes a noise control for reducing the noise overexposures of continuous mining machine operators. Underground results show a 26.4% and 27.4% noise exposure reduction for the continuous mining machine operator. This research is providing the mining community with an additional noise control to be utilized on continuous mining machines, therefore reducing operator noise overexposure. Utilizing this newly developed noise control, along with previously proven controls for the continuous mining machine chain conveyor, will provide operators of these machines an opportunity to be within the MS HA-Permissible Exposure Limit (MSHA-PEL).

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

The modern resource extraction enterprise is a complex capital intensive business operating in a world of constantly evolving social, environmental and economic scrutiny. Investors, government, media and special interest groups expect to see business environmental and social performance respond and deliver increasing corporate responsibility and sustainability.   Thorough interrogation of business performance using a multi-disciplinary due diligence approach presents a more sophisticated review and benefits beyond the traditional compliance/conformance 'audit' style assessment.   Using a due diligence approach allows assessment through a comprehensive lens which examines potential short- and long-term risks including sometimes less tangible environmental and social liabilities, and informs management, investors and regulators of broader business performance. This approach provides information in a form that business can measure performance in a repeatable and enterprise wide sense.   This paper provides an outline of the due diligence process applied in this way, drawing from lessons learnt and industry based experiences in the due diligence process and the benefits and tools that can  be applied in an environmental and social due diligence business performance assessment

Jun 1, 2010

By T. E. Warner

In order to detect arsenic and antimony in zinc, various electrochemcial experiments were performed involving the electrochemical introduction of sodium atoms into molten zinc using a solid electrolyte. Under high rates, the formation of the intermetallic phase NaZn13 was assumed to form. Under more moderate injection rates of sodium, employing a symmetric "zinc/zinc cell", a qualitative relationship between the current generated during cyclic voltammeuy and the arsenic and antimony concentrations in molten zinc was observed.

Jan 1, 1999