Search Documents

By Xun Zhang, Hang Qiu, Andrea R. Gerson4, Shaomin Lei, Yubiao Li, Yu Meng, Zhenyu Pei, Min Lin

Efficient separation of trace muscovite from the surface/interface of quartz grains was accomplished during oxidizing calcination and catalytic pressure leaching of the hydrothermal quartz. Experimental results suggest that 98.97% or more of the muscovite was separated when quartz sand was calcined at 900 °C for 5 h and then leached by hydrochloric acid and ammonium chloride solutions as substitutes for leaching agents containing fluorides. The chemical processing techniques show high selectivity in purifying quartz sand by transforming mineral muscovite into active structures during oxidizing calcination, and then dissolving the active substances during catalytic pressure leaching

By Mala R. Ciancia

Planned tunnel projects with advanced geotechnical investigations are more frequently being suspended because of changes in funding, politics, or local priorities. Some of these projects are ultimately canceled, some decelerate and stall, some resume after a short pause, and some restart after being mothballed for several years. The restarted project often differs at least slightly from the predecessor project in terms of alignment and design concept. This paper describes approaches to evaluating the quality and completeness of previous geotechnical investigations for a re-activated project, considering technological advances as well as changes in regulatory requirements, contracting approach, and site conditions which may have taken place in the time since the project was suspended.

Jun 13, 2021

By Ricky Chipka, Roshan Thapa, Richard Yovichin, Greg Rogoff, Patrick Niemuth

A 4.5-mile-long, 96-inch-diameter outfall pipeline was constructed between North Texas Municipal Water District’s proposed Sister Grove Regional Water Resource Recovery Facility and the Stiff Creek Discharge Structure. Two TBM-mined tunnel segments were excavated for the outfall pipeline through rock and mixed-face conditions within the Austin Chalk Formation. The TBM mining performance was tracked in detail and evaluated during mining. This paper discusses the TBM configuration, TBM utilization, advance rates, and challenges of both tunnel segments.

Jun 13, 2023

By K. K. Bhattacharyya

Vast deposits of lignite occur in the Gulf Coast states and northern plain states. Lignite resources are cited to be over 43 billion tons in the Gulf Coast states. An additional resource of 16 billion tons are reported in North Dakota (Jackson, Smith, 1981). All lignite in the U.S. is mined at present by the open pit method. Draglines and scrapers are primarily used to remove the overburden. Bucket-wheel excavators are also being considered for new mines in the planning stages. Lignite seams are mined using front-end loaders, shovels and trucks, or Easi-miners. The depositional environment of lignite is weak sedimentary soils and rock. Ground water is often encountered within the mining depth. Surface water resulting from heavy rainfall or snow melt contributes to the problems of mining. Mining depths of up to 60 m (200 ft) are under consideration. Draglines exert additional loads on the highwalls and spoil piles. The combination of any number of these factors may cause instability of the slopes. Bearing pressure, trafficability, and settlement can also be a problem for excavation and loading equipment.

Jan 1, 1982

By HONGWEI YANG, Lili Zhang

The oxidation behavior of copper smelting slag under non-isothermal conditions was studied by thermal analysis. The results indicate that the copper slag is mainly composed of fayalite ( Fe2SiO4) and magnetite ( Fe3O4). The oxidation behavior can be divided into two reaction stages with the increase in temperature; the first stage is the oxidation of fayalite to magnetite, and the second stage is the oxidation of magnetite to hematite. The two reaction stages cannot be strictly separated; that is, the reaction of fayalite is not complete, and magnetite has begun to transform into hematite. Based on the TG (thermogravimetric) curves, the ABS (Achar–Brindley–Sharp–Wendworth) differential and the Coats–Redfern integral methods were employed to investigate the oxidation kinetics of copper slag during the continuous heating process. The oxidation of fayalite into magnetite and amorphous silica phases occurs mainly in the temperature range of 673 to 1083 K. The activation energies calculated by the two methods are 193.69 and 195.52 kJ mol− 1, respectively. The reaction is consistent with Avrami–Erofeev equation, and the mechanism of oxidation is random nucleation and growth. The oxidation of magnetite to hematite occurs at 1083–1303 K. The activation energies are 308.79 and 328.77 kJ mol− 1, respectively. The mechanism conforms to the Jander equation and is controlled by the two-dimensional diffusion.

May 16, 2022

By D. K. DeForest

The olfactory system (sense of smell) is crucial to the ability of fish to avoid predators, recognize kin, and synchronize reproduction (Baldwin et al. 2003). Copper (Cu) has been shown to impair olfaction in juvenile freshwater life stages of salmonids (including Pacific salmon and trout) in some laboratory experiments; and in the United States, public concerns have been expressed that current regulatory criteria for Cu in fresh water are not adequately protective of olfactory function in salmonids (e.g., OSU 2007; Pearson 2007). These concerns have largely been raised because some Cu concentrations that have caused olfactory impairment in salmonids in the laboratory are less than Cu concentrations that have been shown to reduce salmonid survival, growth, or reproduction (the effects endpoints that are typically considered in deriving ambient water quality criteria). However, two important and interrelated points that must be considered: (1) freshwater Cu criteria are "driven" by the sensitivities of several invertebrate species that are more sensitive than the olfactory impairment threshold in salmonids when (2) the influence of water chemistry on Cu bioavailability is properly considered in deriving Cu criteria. Bioavailability refers to the ability of various chemical forms of Cu to interact with receptors on the surface(s) of organisms and thus directly cause toxicity or uptake by the organisms. The toxicity of Cu and other metals to aquatic organisms is a function of water chemistry. For example, acute Cu toxicity in fresh water generally decreases as pH, water hardness (Ca2+ and Mg2+), alkalinity, and dissolved organic carbon (DOC) concentrations increase (Meyer et al. 2007). The U.S. Environmental Protection Agency (USEPA) has recommended hardness-based freshwater aquatic life criteria for Cu and other metals since the 1980s (e.g., USEPA 1985); and hardness-based metals criteria decrease (i.e., become more restrictive) as water hardness decreases. More recently, the USEPA has recommended freshwater aquatic life criteria for Cu based on the biotic ligand model (BLM; USEPA 2007), which accounts for the influence of multiple water chemistry parameters, including DOC, pH, alkalinity, Ca2+, Mg2+, and several other cations and anions. The BLM-based Cu criteria generally decrease as DOC concentration, pH, alkalinity, and water hardness decrease. Because DOC has a stronger influence on Cu bioavailability than water hardness, hardness-based and BLM-based Cu criteria can differ considerably. For example, in water that has low DOC and high hardness, the hardness-based Cu criterion would be relatively high (because it is driven by the high hardness) but the BLM-based Cu criterion would be relatively low (because it is driven by the low DOC). Thus, any evaluation of the protectiveness of Cu criteria against a given effect, such as olfactory impairment, must properly account for the chemistry of the exposure water. Meyer et al. (2013) compiled data on Cu-induced olfactory impairment and olfactory-induced behavioral effects from tests in which BLM parameters were measured. They demonstrated that the USEPA's BLM-based freshwater life criteria for Cu are protective against olfactory impairment, because it adequately accounts for water chemistry (whereas the USEPA's hardness-based Cu criteria are not consistently protective). Olfactory impairment by Cu is now receiving increased attention in Canada and Europe (e.g., Wall 2013; Stang 2013). Accordingly, in this paper we have expanded the analysis of Meyer et al. (2013) to consider copper guidelines from various other countries and whether these guidelines are protective against olfactory impairment.

Feb 23, 2014

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By Harrison R. Cooper

Approximately 40 concentrators throughout the world have successfully adopted computer control for flotation circuit operation since 1969. Successful use of flotation control, gaining up to 2% efficiencies, has largely derived from effective employment of on-stream slurry analyzers and integration of key measurement data through digital processors. Requirements for reliable measurement have also led to improved functional reliability in magnetic flow meters, pH, reagent feed, and other key elements. Methods used in computer control of flotation will be reviewed and variations in operating philosophies will be described with reference to the approaches taken to flotation automation.

Jan 1, 1979

By D. K. Mynear, J. S. Gardner, S. Mittle, A. A. Campoli

West Virginia, although having adequate solar insolation, has witnessed very little actual solar development to date. The reasons for this lack of development are varied, but the primary obstacles to future development appear to be the absence of state-level policies and regulations promoting growth in the solar industry. West Virginia possesses large tracts of under-utilized land throughout the state created by previous mountaintop mining operations that could theoretically be re-purposed for solar farm development. Accomplishing this task will require not only revisions to the current legislation, but also acceptance by utility companies, landowners, and mining companies. Solar developers will need confidence that they can secure revenue from the electricity and Renewable Energy Certificates (RECs) generated by solar projects. Additionally, solar companies will need assurance they will be protected from any non-related environmental liabilities that could arise in the future. The primary avenue in bringing significant solar development to West Virginia will come through large corporate clients demanding or partnering with utility companies for incorporation of solar options into their energy portfolio to help meet established sustainability goals. This scenario has been witnessed in other states where a large client demands renewable options. Solar development could also represent a means through which mine operators might alleviate some of their reclamation and bonding obligations; where the landowner could supplement income from their underutilized land holdings; and where displaced miners could be repurposed in solar installation/maintenance jobs. Utilizing data from the West Virginia Permit Database, this report identifies several mine sites that hold potential for solar development in the future. INTRODUCTION The diversification of energy sources in the United States (US) has seen major shifts during the past decade resulting from: • A sudden abundance of low-cost natural gas becoming available through advanced horizontal drilling and hydraulic fracturing techniques. • Incentive-driven policies leading to new development in alternative energy. • The emergence of renewable energy sources, proliferated by state and federal level incentives and falling capital costs. Coal was once the primary low-cost fuel source for the generation of electricity in the US for most of the last century, providing approximately 50 percent of the total production capacity. However, within the past decade lower-cost natural gas has overtaken coal as the primary source of fuel used in electricity generation, and renewable sources have steadily grown to account for approximately 10 percent of the overall mix.

Jan 1, 2019

By Bruce L. Bryson

In the past decade a principal growth area in refractory technology has been the development and use of extra high alumina refractories. The refractories user is asking for, and is prepared to pay for, higher purity, more dense materials with longer life, less maintenance, and better dimensional tolerance to meet the exacting demand of high output processes. High alumina and bauxite refractories are being used more and more to keep pace with the demand for guaranteed performance. The steel industry, for example, is starting to place great reliance on these products. A unique material now available with all the requirements for extreme purity and density is tabular alumina, already proving itself in many refractory applications.

Jan 1, 1973

By J. E. Gray

Before specifications are discussed it may be well to define the term "Mineral Aggregates." Professor K. B. Woods (1) defined "Mineral Aggregate--An aggregation of sand, gravel, crushed stone, slag, or other material of mineral composition used in combination with a binding medium to form bituminous and portland cement concrete, macadam, mastic, mortar, plaster, etc., or alone as in railroad ballast, filter beds, and various manufacturing processes, such as fluxing, etc. " This definition is too all inclusive for the purposes of this paper; therefore, this discussion will be confined to specifications for natural aggregates which means sand and gravel and crushed stone, and limited primarily to coarse aggregate which is aggregate larger than one-quarter inch in size. To the uninitiated, this may seem to be a very limited subject on an unimportant material. However, aggregates are essential in all types of construction. The tonnage and value of these two aggregates produced in the United States during 1959 as reported by the Bureau of Mines were as follows: Sand and Gravel 729,895,000 tons valued at $728,527,000 Crushed stone 581,721,000 tons valued at $824,411,000

Jan 1, 1961

By S. C. Tadolini, P. Mills

"INTRODUCTION This research produced a shotcrete formulation that extends beyond stabilization and can be used to restore the structural integrity of damaged infrastructure. The primary challenge was to develop a shotcrete or gunite with structural strength within a few minutes to prevent parasitic loading and allow ingress into damaged structures within a few minutes of the mix formulation being applied. This also applies to mining conditions where rapid support of progressive failures can minimize failure. An additional benefit was the discovery that the product had extremely high adhesion properties in addition to high flexural strengths. The approach to product design was the development of “single bag” dry mixes that are entirely self-contained, can be rapidly transported anywhere in the field or underground, and be deployed using simple equipment. Dry mix eliminates issues relevant to high shear water mixing, as water is added in the form of a mist at the point of delivery; thus low W/C can be achieved. However, as there is no onsite powder mixing, the product must have a high degree of inherent homogeneity. A commercial version of this material is currently offered as Minova’s Tekcrete Fast® product which has been successfully deployed in the mining industry and is currently being used in civil, construction and tunneling operations. The material can rapidly stabilize unstable ground in metal/nonmetal and coal mines. This paper described the technology development, product testing results and applications in mining and civil applications. BACKGROUND The original development of this product was to complete rapid stabilization of shock damaged structures, which falls outside the purview of normal construction and mining practices, due to the critical time issue and the nature of the damaged structure. The stabilization of damaged structures requires materials and equipment that can be rapidly deployed to place materials that have very rapid strength development. These materials need to be placeable at a distance to provide some degree of safety to the responders. In addition, the materials must be able to adhere to structural surfaces that have not been specially prepared and conditioned, and may also be highly fractured, dusty, wet, and quite possibly hot or extremely cold. The technology for the rapid delivery of large volumes of cementitious materials to vertical or even overhead surfaces currently exists. Pneumatic delivery (shotcreting) has been used in construction for over 100 years (American Shotcrete Association, 2014). Shotcreting has played a major role in structures like the Washington D.C. Metro subway system and been used in underground mining applications routinely to serve as part of the primary and secondary support system when used in conjunction with traditional roof bolts. Numerous rapid setting cements are commercially available. They are used for rapid repair of surfaces such as bridge decks, pavements, and commercial floors, as well as structural repairs of vertical and overhead surfaces. Few of these products are specifically marketed for use in shotcrete applications. The majority of rapid setting cements are based on, or at least contain, Portland cement as a principle component. Other components are added that help provide early strength, such as high alumina cement (HAC), organic polymers, chemical accelerators (which can also be added during concrete batching), and calcium sulfate hemihydrate (e.g. gypsum plaster) (Lea, 1971). Cementitious mortars prepared with some of these cements can achieve compressive strengths of 6.8 – 13.8 MPa (1,000-2,000 psi) within 1 hour. However, Portland cement mortar and concrete typically require many weeks of proper curing to reach significant levels of their ultimate strengths, even when used with set accelerators. Also, high early strengths require the use of large proportions of Portland cement in the concrete mix, which can lead to high heat evolutio"

Jan 1, 2017

By P. Rosario

During the last few years high-tonnage plants have been designed with comminution circuits using semiautogenous grinding (SAG) mills, high pressure grinding rolls (HPGR), or both, followed by ball mills in different configurations. A strong interest in improved energy efficiency and reduction of carbon footprint, along with the recent launch of new high-capacity crushers and stirred grinding mills, has driven the industry to investigate the development of novel flowsheets. This paper presents work based on recent projects that include modeling and simulation of two innovative circuits recently considered for current projects. One circuit uses autogenous (AG) mills and parallel trains of crusher-HPGR and the other is a modified three-stage crushing circuit with the use of HPGRs and pebble mills. The paper indicates the potential savings in operating costs provided by the HPGR-pebble mill circuit when compared to a more conventional SAG-mill-based circuit.

Jan 1, 2010

By Martin H. Stanczyk

The Organic Act of 1910 established the Bureau of Mines and gave it authority and responsibility for conducting research on separation, recovery, and recycling of waste products and scrap generated by the mineral and metals industries and the consuming public.(1)1 It was apparent to our Nation's leaders even then that mineral resources, once mined, are irreplaceable and that the development of methods for recycling the values contained in wastes would be required to solve the problem of even¬tual scarcity, Estimates of the increase in per capita consumption of mineral resources in this country indicate that the consumption of metals, minerals, and fossil fuels by 1980 will be double that consumed in 1970 (2). The United States can expect to meet its future mineral needs in three basic ways: the first is through increased production of primary raw minerals; second by increasing imports from foreign sources; and third by recycling secondary materials and metals that were formerly discarded as waste. Rather than consider these

Jan 1, 1972

By Robert L. Zook

Coal refuse slurry impoundments are dams constructed of coarse coal refuse to impound fine refuse (slurry) and water (25-30% solids). Both products are waste from coal preparation plants. A number of these structures in West Virginia, Pennsylvania and Kentucky were investigated to determine embankment stability. During the investigation a variety of embankment designs were encountered. The investigation determined the soil and geological characteristics of the embankments and the sites. This was accomplished by a test drilling and monitor installation (observation wells and piezometers) program, geologic study, and large scale mapping which allowed sub-surface profiles of the embankments to be constructed. The laboratory testing program concentrated on textural classification of the coal refuse, permeability and determining strength parameters to be utilized in the stability analyses. For the stability analyses, the Modified Fellinius Slip Circle, Simplified Bishop Slip Circle and Analysis for Translational Failure -were utilized. In all stability analyses hydrostatic pressure and earthquake were considered. This investigation indicated that 62% of the embankments analyzed are in a stable condition. The coal seam mined, the type of roof rock, and the gradation of the refuse influence the degree of compaction obtainable and the permeability of refuse. The shear strength of coal refuse appears to be controlled by its composition, moisture content, degree of compaction, amount and grain size of fines present. This investigation demonstrated these em¬bankments should not be treated as pure state-of-the-art dams; consideration must be given to the particular properties of coal refuse and the total refuse disposal system. Refuse dim slurry impoundments generally lack the site se- lection phase that is standard practice with siting most other types of dams.

Jan 1, 1974

By Atta Ur Rehman, Kwame Awuah-Offei

This paper examines the effect of bucket geometry (cutting-blade profile, floor profile and blade thickness), speed, motor power output and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scale model of a load-haul-dump (LHD) in full-factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated with penetration and draft, and muckpile particle size is positively correlated with penetration and negatively correlated with draft (p < 0.0014).

By Dean Treweek, Anthony Harding

"Creating stable, safe, constructible and cost effective support to openings in segmental linings is often an important component of successful delivery of a tunnel project. The many constraints on successful implementation include operational, spatial, geotechnical, structural, and constructability. Failure to address these adequately can lead to significant impacts on cost, schedule, and safety. With reference to past project experiences, this paper provides a guide to the most commonly deployed solutions and their pros and cons to help designers quickly identify the most appropriate solutions for a particular project, or act as a starting point for developing new and/or project specific solutions. It highlights the challenges that designers and contractors must address together for successful support of tunnel openings, and the constraints that arise. It then describes the common structural forms of support, and how each form can mitigate the constraints, allowing an effective opening support system to be implemented. INTRODUCTION While only a small portion of the total excavated volume of a typical tunnel, cross passages are often one of the most complex elements of a bored tunnel to construct. Cross passages in soft ground typically involve ground improvement, groundwater control, and multiple temporary support measures to ensure safe construction in ground that has been overstressed due to the construction of the running tunnels. Permanent lining construction requires careful detailing of waterproofing and reinforcement to support both long term ground and water loads and support the broken out rings of the main lining. While there is not a great deal of literature specific to cross passage construction, the main issues are discussed in some detail by Lawrence and Taylor (2011). However, the temporary support of the running tunnel segmental linings during cross passage construction is not always given the attention it deserves. The authors have been unable to find much literature on the design of such systems, much less the considerations that have led to a particular solution. Lawrence and Taylor only mention two potential methods of support. It may be easy to dismiss the opening support as an inconsequential item, but selection of the wrong support type can have significant impacts on both cost and schedule."

Jan 1, 2016

By W. K. Utt

This report discusses U.S. Bureau of Mines&apos; research involving modem vehicle position determination techniques in surface mining. The applications would include haul trucks, power shovels, and drilling rigs. Accurate position determination of these vehicles in near real-time is expected to result in safer and more efficient mining operations. The requirements for a vehicle position monitoring and warning system were determined. After screening several concepts, the global positioning system (GPS) and a radar positioning system were selected for further evaluation. A state-of-the-art GPS receiver was taken to a surface mine to assess the feasibility of receiving the satellite signals. A state-of-the-art radar positioning system was evaluated with regard to accuracy.

Jan 1, 1995

By Hans E. Tausig

The economics of transporting minerals by sea in less than full cargo lots encompasses an analysis of production costs, sale and inventory calculations and a careful comparison of ocean freight costs all of which when pieced together will usually definitively indicate which of the ocean freight alternatives is the correct one for the economic factors involved. To illustrate: Let us assume that a production to be marketed yields 60,000 metric tons of copper concentrates over a twelve month period. Shipment is geographically viable through Vancouver, B.C. The production has been sold to a Japanese Smelter and the mine produces at a rate of 5,000 metric tons of concentrates per month. The copper has been sold CIF FO. The Seller has carefully investigated ocean freight rates Vancouver, B.C./Hibi, Japan and finds that he could obtain a twelve month freight contract at $15.00 per metric ton FIGS based on a loading/discharging speed of 4000/ 2000 metric tons per WWDSHEX (weather working day, Sundays and Holidays excluded) this freight rate being predicated on shipping in lots of minimum. 15,000 tons. A further freight investigation reveals that to ship at the same terms and conditions but in lots of 5,000 tons, and shipping each month (in accordance with the mine&apos;s actual production) would cost $20.00 per metric ton FIOS. The calculation that is now made is whether it is more desireable to pay a higher ocean freight by shipping in 5,000 ton lots or to pay the lower freight where here the ocean freight involves a difference of some $300,000.00.

Jan 1, 1979

By A. Vilinska

The adhesion of Leptospirillum ferrooxidans bacterial cells onto the sulfide minerals pyrite and chalcopyrite was evaluated using two different physical-chemical approaches; thermodynamic and extended DLVO theory. For the parameters incorporated into calculations, the zeta potentials and contact angles of powdered solids and bacterial cells were acquired experimentally. The Hamaker constants essential for Lifshitz-van der Waals inter-action calculations were calculated following two different methods: macroscopic and microscopic. Adsorption tests were carried out at physiologic conditions to estimate the amount of cells adsorbed onto a mineral surface and the extent of alteration of that mineral surface in biobeneficiation. The free energy of adhesion was found to be negative for both minerals, indicating that the adhesion is energetically favored and preferred. The interaction energy diagrams of the total interacting force was also negative for the cases where the particles were charged oppositely; in the remaining cases, the total force was attractive after overcoming an energetic barrier caused by the repulsive electrostatic forces. Under the conditions of the adsorption test, the experimental results are in agreement with the theoretical; this suggests that the physical-chemical forces are crucial for bacterial adhesion.

Jan 1, 2011