Search Documents

By M. Fig, J. Brune, C. Strebinger, G. Bogin

"A fundamental understanding of flame propagation characteristics through and around obstacles is needed to accurately model methane driven longwall coal mine explosions originating or propagating in the gob. Experimental investigations of methane flames in horizontal cylindrical reactors with simulated gob (i.e. rock piles) were carried out alongside coupled Computational Fluid Dynamics (CFD) and combustion simulations. Stoichiometric methane-air mixtures were ignited in semi-open reactor vessels of 5cm, 9.5cm and 71cm diameter, all with a fixed length to diameter (L/D) ratio of 8.6. This was done both with empty reactors and also with a rock pile placed at the open end of the reactor. The rock pile length to reactor length ratio was fixed at 0.3, and the rock pile height to reactor diameter ratio was fixed at 0.33 for all reactors. The smaller two reactor experiments were modeled with ANSYS Fluent in 2D. Experimental results indicate that for this geometry a similar acceleration mode occurs across scales: that the flame speeds up an average of 40% as it passes over a rock pile with this profile. The model is able to capture several important features of the experimental results, including the significant increase in velocity, the speedup ahead of the rock pile, and the leveling off of the empty tube flame front propagation velocity. INTRODUCTION Explosions in underground coal mines are among the largest industrial explosions, known to result in the rapid combustion of 20m3 of fuel gas or more [1,2] Coal beds hold methane gas under pressure, and when the pressure is relieved through mining activity some of this methane is released. The methane then mixes with ventilation air and, if not sufficiently diluted, may form a combustible mixture, which may result in an explosion. Several large coal mine explosions have occurred around the world recently. These include the 2014 Soma Mine disaster in Turkey that killed 301 people [3], and the 2009 Heilongjiang Mine explosion in China that killed 108 [4]. Other recent mine explosions, including the 2010 disaster at the Upper Big Branch mine that caused 29 fatalities [5], have demonstrated that explosive gases can accumulate and ignite within and around the gob area of a longwall coal mine and then expand into the active mining face and nearby areas, endangering workers and equipment. If enough combustible gas is involved, the initial flame can accelerate, eventually transitioning from deflagration to detonation [6]. Researchers are developing a fundamental understanding of the evolution of the explosion process from the laminar kernel to the fully turbulent regime, and its propagation through obstacles such as those found in the gob. Researchers also studied the initial development of methane flames and the potential for the development of a detonation."

Jan 1, 2018

By D. Newman

Ground control is critical to the success of a safe and productive underground stone mining operation. The primary focus of the ground control engineer is the stability of the roof or back; development and benched pillar stability; stability of the sill pillar between vertically adjacent mining levels; and floor stability. Roof stability begins with the selection of a stable back horizon based on the presence of a thin shale parting, stylolite or other discontinuity from which the production shot can easily peel away, leaving a stable back stratum. Bed thickness, fracture spacing, jointing and the material properties of the roof strata control the room width; the decision whether to bolt the roof; the bolt length, type and diameter; and the spacing of the roof support. Horizontal stress controls the header and crosscut azimuth. The mine operator should avoid driving perpendicular to the maximum horizontal stress direction. Where this is unavoidable, narrowing the opening width, narrowing pillar centers, increasing the support density and using three-way intersections are alternatives to remediate shearing along the roof-rib interface. Stable pillar dimensions depend upon the interaction of the vertical stress resulting from overburden thickness and multiple-level interaction of overlying level or levels; the mining height during development and the final mining height after floor shots are taken during benching; the presence of faults, folds or joints passing through the pillar; and limestone lithology, recognizing that the presence of oolitic bands, shale partings, joints and bentonite beds creates zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone typically exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture-sensitive strata, weak stone bands or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. To illustrate these ground control issues, this paper presents four case histories that are a mix of ground failures and successful mining. The focus is on the geotechnical data required for roof, pillar and floor design and stability analysis.

Jan 8, 2017

By Steve Kral

"The Rapid Excavation & Tunneling Conference (RETC) is a world-renowned event that attracts some of the best minds in the global underground construction and tunneling industry. The experts gather at this conference to impart new technologies, discuss challenges to their projects and learn about new technologies that have become available to them.The 2015 RETC will be held June 7-10 at the Sheraton New Orleans, in New Orleans, LA. This biennial conference, of which SME is a sponsor, is expected to attract about 1,400 attendees from around the world. These professionals represent all parts of the global tunneling and underground construction industries - contractors, engineers, owners, consultants and equipment suppliers.More than 110 technical papers in 21 sessions will be presented over two-and-a-half days. Paid attendees will receive a proceedings volume of the conference. The proceedings will also be available from SME. In addition to the technical programming, the accompanying exhibit will include 155 exhibitors occupying 175 booths, providing RETC attendees the opportunity to get a look at the latest in equipment and service technology. Three short courses will be held on the Sunday preceding the start of the show. And there will be plenty of opportunities for attendees to meet and chat during several social activities that are scheduled throughout the conference."

Jan 1, 2014

By Qingwen Shi, Brijes Mishra

Laminated rock can delaminate and fail under certain stress states. Delamination-caused roof fall and cutter roof failure is a common failure mechanism in roadways in Pittsburgh coal seam due to the existence of laminated shale roof. Two-dimensional numerical models were developed at laboratory scale based on the bonded particle method in order to simulate the delamination with particle flow code. In these models, an assembly of bonded particles and parallel weak planes represents the laminated rock. This model calibrated the micro-parameters of the bonded particlematerial and weak planes with laboratory data. The mechanism of fracturing and delamination in a laminated specimen was investigated using unconfined and confined compression test and unsupported roof compression test. The numerical results show that, under a constant horizontal stress, delamination occurswhen the stress is much lower than its compressive strength. The confined compressive test indicates that delamination is restrained by applying confining stress since delamination-caused failure does not occur during any stage of the confined compressive test. Unsupported roof compression tests showed propagation of cutter roof failure with initiation of cracks and delamination at the intersections of the roof and ribs. An outer failed zone and inner failed zone form separately. The separated zones connect and form an opening in the roof. The presented numerical results provide additional insight into process of delamination.

Sep 14, 2020

By Ronald T. Cosburn

The Province of Ontario covers an area of some 400 thousand square miles, however the subject I will be talking about today, the licencing of pits and quarries in southern Ontario, refers to about one quarter of this total area but contains better than 93% of the total population of the province or about 8 million people. Southern Ontario had and still has many inviting features to industry. The Great Lakes almost surround us, hydro power has been relatively inexpensive and abundant, but more in line with our topic today are the ample deposits of sand, gravel and limestone, all of which are used directly or indirectly throughout and are the mainstay of our construction industry. I say we are fortunate to have these non-renewable resources in abundance in close proximity to our industrial and metropolitan areas, but like so many of our resources we have taken them for granted for too long. What has happened in our case, as I am sure is common in many of your own similar situations, because of the recent, current popular trend by naturalists and environ- mentalists to preserve our natural heritage at the expense of all else, through parklands and indiscriminate zoning policies, these once abundant reserves have been tremendously eroded.

Jan 1, 1982

By S. M. Alvarez

The Moon Creek Reclamation Project provides a case study in the development of creative cleanup solutions for an abandoned lead and zinc mine and mill site located in northern Idaho. Innovative design features include construction of a 88,000 cubic yard combined waste containment facility on soft in-situ tailings, water-balance cap, limestone gravel drains, a geocell mattress for stability, and a below-grade scour protection berm. The stream, including a wetlands buffer, will be relocated within an existing road alignment and rehabilitated to provide trout habitat. These elements allow for the integration of reclamation and stabilization measures into an effective site design.

Jan 1, 1999

By Tyler A. Dawson, Ryan P. Butler, Timothy Gualandri, Jason R. Edberg

"In the early 1920’s, the City of Tulsa, Oklahoma constructed an approximately 8,238-foot long tunnel, the Tiawah Tunnel, through bedrock. Voids behind the concrete tunnel liner were detected via probe drilling in early 2000 as part of an interior visual condition assessment. In 2012 and 2015, conditions along the entire tunnel were efficiently assessed through geophysical investigation using ground penetrating radar (GPR) along the inner tunnel crown and at various select locations within the tunnel. Fifty-seven (57) potential voids, extending up to 19 inches in depth and 12 feet in width, were detected with 1,000 MHz GPR and confirmed through probe drilling with approximately 80% accuracy. GPR proved to be an efficient and reliable technology for void detection behind concrete tunnel lining. This paper highlights the geophysical investigation and how geophysical efforts were combined with other investigation efforts to definitively determine the presence of voids outside of the tunnel lining.INTRODUCTION The city of Tulsa, Oklahoma has a population of about 400,000 people. The original source of water for the city was the Arkansas River. The first pumping operation provided untreated water to homes and businesses in 1904. The residents of Tulsa found this water to be unacceptable due to the high levels of salt and gypsum present. As the city grew, land and storage/treatment facilities were acquired in order to obtain and distribute a more suitable raw water. The raw water needs for the city are currently satisfied by transport and treatment of about 100 million gallons per day (MGD) of water from surface water sources. Water is transported many miles from Spavinaw/Eucha and Oologah lakes to Yahola Lake and the Lynn Lane Reservoir (totaling over 3-billion gallon capacity). From here, the raw water is treated and transported to the various customers (City of Tulsa 2015). The Tulsa Metropolitan Utility Authority (TMUA) is responsible for the operation and maintenance of the raw water transport system."

Jan 1, 2016

By Marcus M. Key

Silicosis among metal miners is an ancient disease, probably as old as mining itself.' However, the primitive forms of mining were not productive of much silica dust, and the short life span of slaves used in mining probably precluded the development of more than a few sporadic cases of silicosis. Early diagnostic terms of miners' asthma and miners' phthisis suggested an occupational relationship and a tubercular component, but little attention was given to silicbsis until the turn of this century when epidemics of silico-tuberculosis arose due to the great expansion of the mining industry in the United States, especially silver and gold mining. The expansion was accompanied by mechanization and the introduction of pneumatic tools, which generated increasing amounts of fine silica dust. Mining communities were crowded and hygiene was poor.' The tubercle bacillus would probably have flourished even without the predisposition of silicosis.' As is so often the case in occupational health, biostatistical analyses first called attention to the problem, and environmental-medical studies later confirmed its existence. The bio-statistical analyses were occupational mortality statistics compiled by the Prudential Life Insurance Company in 1907, showing evidence of excessive mortality from tuberculosis and relationship to dust exposure. I The

Jan 1, 1971

By Jalal Vakili

In designing very large excavated slopes which are becoming increasingly common in both mining and civil engineering projects, the most important decision of the engineer is the selection of a slope angle. The purpose of the geotechnical study of the slope is to ensure reasonable stability of the slope in the most economical way. Because the rock mass composing each slope is unique, there are no standard solutions for slope stability analysis. A practical solution is formulated from the basic geologic data, engineering properties of the rock, geometry of the slope, and ground water observations. Stability analysis consists of analyzing the forces causing and resisting slope failure. There are several methods of slope stability analysis. The limit equilibrium method evaluates the overall stability of the sliding mass just on the verge of slip, using some or all of the three equations of static equilibrium of a plane problem. The stress-strain relationships of the rock mass are not considered. Method of analysis include the assumption of the shape of the slip surface. Peterson (10) introduced the Swedish method of analysis in 1916, which is based on cylindrical sliding surfaces. Fellenius (4) in 1926 extended this method and introduced the method of slices. This method was refined by Bishop (I) in 1955 and later used by Morgenstern and Price (8) in 1965. In many cases layers of extremely soft strata or strata weakened by neutral stress cause failure to take place by translation along plane of weakness instead of by rotation on a circular surface. In this paper, a slope with a horizontal layer of weak meterial is selected for analysis. This is a usual case for open pit lignite mines where lignite seam may be non-cohesive and 'weaker than the overburden rock or a soft clay layer underlies the seam. It is also a common case of rock fill dams supported on a foundation stratum of clay where the strength of the clay layer is less than that of the rock fill. It is shown that utilizing this method, the location of potential failure surface and the value of the minimum factor of safety can be calculated directly and the trial computations of factors of safety for a number of assumed failure surfaces are not necessary.

Jan 1, 1982

By A. Bascetin

Materials produced in quarries have been used for different intentions such as concrete and cement raw material, asphalt and embankment aggregates, railway ballast. Especially in cement manufacturing, the chemical composition and the uniformity of the raw materials play a strategic role in the economy and quality of the cement process. Therefore, it is necessary to achieve uniformity and desired chemical composition and maintain these at all production stages according to the type of cement produced. To achieve this goal the production planning and pit design play an essential role. This paper briefly outlines the production optimization of cement raw materials in a quarry in Istanbul western part of Turkey. For the purpose it was used the 3D ore body modeling and the geostatistical techniques. The variation of chemical components (%CaO, %Al2O3, %Fe2O3 etc.) and quality control parametres (LSF, SR, AR and etc.) obtained from the quarry were determined. Then the values of unknown chemical components and quality control parameters in the ore body were estimated using Kriging which is one of the geostatistical interpolation methods. The open pit design was also created by specifying wall slopes and taking into consideration of the grade distributions of the benches. The most important revolution in the paper is investigating the effects of the block dimensions in block modelling which is important for reserve estimation. The other important point in the study is using the different range values in variogram analysis for determination optimal reserve estimation. n this study, the effects of two parametres on reserve and waste amount estimation were determined according to CaO% distribution. The study was pointed out that the changing of the two parameters are very important for the optimal mine planning and environmental considerations.

Jan 1, 2010

By J. K. Ahlness

The Bureau of Mines investigated technologies for determining the integrity of in situ leach mining wells. A self-contained trailer-mounted well integrity testing system (WITS) was designed and built to enable rapid testing of well casings for leaks as required by environmental regulations. The WITS utilizes two inflatable packers to seal off the entire casing length or any portion thereof. Water pressure is built between the packers to the desired test pressure, and the presence or absence of casing leaks is determined by monitoring the pressure drop between the packers. A winch and steel cable are used to run the packers in and out of the well. The WITS underwent an industry field test at the Irigaray in situ uranium leaching mine near Buffalo, WY. A total of 37 wells with an average depth of 225 ft (69 m) were tested at an average rate of four wells per 8-h shift with a two-person operating crew. This represents a 75-pct time savings and an 83-pct labor savings compared to the rigid-pipe method previously used at the mine, with which a three-person crew tested an average of one well per shift.

Jan 1, 1986

By Xiaozhen Song, Ashish Ranjan Kumar, Shimin Liu

Diesel particulate matter (DPM) presents considerable occupational health hazards in large-opening underground mines (LOUM). Previous studies have primarily focused on single-factor ventilation optimization, while this study innovatively integrates booster fan configurations and loading truck placements utilizing a coupled CFD turbulence– particle tracing model. Three distinct ventilation scenarios were simulated to evaluate their effects on DPM dispersion and dilution efficiency. Results indicate that dual booster fans substantially enhance airflow distribution, increasing air exchange efficiency; The migration pathways of DPM closely align with airflow trajectories, and air turbulence is the predominant factor influencing particle behavior within LOUM; Loading truck placement critically influences local DPM accumulation; Airflow effectiveness diminishes markedly with distance from booster fans, causing stagnation at distant working faces. The coupled CFD approach accurately captured airflow–particle interactions, offering valuable insights for optimizing mine ventilation strategies and effectively mitigating miners’ exposure to DPM.

Feb 22, 2026

By Frederick B. Brien

For many years tin mining in Bolivia has been very important to the economy of the country. In recent years the tin content of the ore reserves has been steadily declining. An improvement in concentration efficiency is highly desirable in order to increase productivity from the present-low-grade mine ores and to allow retreatment of the many millions of tons of tailings from past operations, some of which equal the present ores in tin content. A number of investigators have been or at present are working on various phases or approaches to the problem. Gravity concentration is used in Bolivia today as it has been in the past to recover tin minerals from the mine ores. An objective of the work reported in this paper was to examine the possibility of treating present low-grade ores and sink-float tailings products, at a relatively coarse grind, in order to produce a higher grade feed material to the present gravity concentration plants. The possibility of using heavy liquids in cyclones to treat large tonnages with a minimum of outlay presented itself and is of particular interest since appropriate heavy liquids are available and with physical properties which lend themselves to simple recovery methods. Tests were carried out using a closed circuit laboratory cyclone assembly. It was desirable to determine the value of using the SG50 concept and Tromp curves for analyzing the cyclone concentration test results. The effects of entrained water on the behavior of ore particles in the cyclone were examined.

Jan 1, 1964

By Andrew W. Jenike

The first significant studies of problems related to the handling and storage of bulk solids were reported at the end of the nineteenth century. Early work originated from the necessity to store large quantities of grain and was concerned mainly with pressures affecting the structural design of silos and bins. The Janssen formula (about 1898) and the work of Ketchum [1] form the highlights of that period. In more recent years, progress in mechanization, increasing plant capacities, and rising costs of labor have focused the attention of engineers on the problem of gravity flow of bulk solids. A great deal of work has been done with models, and flow patterns obtained in small scale bins have been described in several publications, for example [2, 3]. An attempt to develop a theory of flow of bulk solids was reported in 1954 [4, 5, 61 and presented to the in a paper [7] in the same year. AIME recommended the continuation of this work and, as a result, Engineering Foundation granted a sum of money to set up a Bulk Solids Flow Laboratory. Two and a half years ago the project gained the support of the University of Utah and a laboratory was set up on the campus of the University. This project is now in progress, it has received the support of the American Iron and Steel Institute and of Kaiser Engineers, Division of Henry J. Kaiser Company. The results obtained to date are summarized in this report.

Jan 1, 1959

By I. Mazalov, G. Ospanova

Introduction Today, uranium is of great interest because of its application to nuclear power and nuclear weapons. Kazakhstan has been an important source of uranium for more than fifty years. All uranium products are exported. Results In Kazakhstan uranium exploration started in 1948 and developed in several parts of the country thru mining of hard rock deposits. There are known around 50 uranium deposits in six provinces: Shu-Sarysuyskaya (57%), North Kazakhstan (18%), Syrdaryinskaya (15%), Ilyiskaya (7%), Caspian (2%), Balkhash (1%). In the Northern Kazakhstan province, KazSabton took over Tselinny Mining & Chemical Co in 1999. In this province the stockwork is of Paleozoic and Paleozoic folded complexes origin. In the Balkash province some mining of volcanogenic deposits occurred during the Soviet era. This province’s stockwork is of Endogenous origin.In the Ili province uraniumis mainly found in uranium-coal deposits formed by oxidation of the lignite beds roofs. In the Caspian province the Prikaspisky Combine operated since the 1960s a major mining and processing complex on the Mangyshalk Peninsula. This led to the founding of Aktau. It was privatised as Kaskor in 1992 and operations ceased in 1994. The uranium occurrence is associated with the phosphorous from fossil fish bone detritus conglomeration. In the Chu-Sarysu province, which has more than half the country's known resources, both Stepnoye and Tsentralnoye have been operating since 1978 and 1982 respectively. Uranium mineralization occurred in the regional stratum oxidation zones. In the Syrdarya province slightly to the west of the province’s center the No.6 Mining group has been operating since 1985. Uranium mineralization occurred in the regional stratum oxidation zones.

Jan 1, 2007

By Norman R. Paterson

In November 1980 a combined airborne electro-magnetic (INPUT.) and magnetometer survey was conducted by Questor Surveys Limited in the State Line Area, Colorado-Wyoming. The survey was the result of discussions over a prolonged period between the authors and various investigators of the State kimberlite occurrences. As a result of these discussions and literature studies, it was decided that airborne geophysical methods would be potentially useful in the exploration for new kimberlite occurrences. The survey was designed by Paterson, Grant and Watson Limited and conducted by Questor Surveys Limited over an area in which more than 15 kimberlite bodies were known and on some of which ground geophysical surveys had been conducted. The survey was designed primarily to determine the airborne electromagnetic and magnetic responses of the known occurrences and to deter- mine whether these responses would be detectable under similar conditions in other parts of the State Line District and elsewhere.

Jan 1, 1984

By S. Todd Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty in factor of safety predictions for soil slopes where there is incomplete knowledge of the spatial distribution of soil properties. A case study considers a natural clay slope in Canada. The sequential indicator simulation technique is used as a means for generating a series of spatial maps of soil properties for this site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. Factor of safety determinations are then made for each simulated map using the simplified-Janbu approach, where the computations are performed with a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the distribution of factor of safety conditional to the type, position, and value of existing site characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1993

By Andre Vien, SANDRO DAVID DI, Frank Laroche

In 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution–size distribution relationship. This allows grade and recovery predictions from a varying mine plan through product size distribution predictions. 

By Fahimeh Dehghani, Louis Ackah, Tathagata Ghosh, Justin Godbold, Jia Liu, Meisam Peiravi, Manoj Mohanty, Azam Baharlouei

Primary economical deposits of rare-earth elements (REEs) are exhausting all over the world, and it has become necessary to find new sources and methods for their extraction. In addition, increasing the application of REEs in modern technological society has increased its demand globally. One of the important movements to compensate for the future shortages of critical metals is the recovery of REEs from recyclable materials. This paper presents a review of the classification and extraction methods, as well as general applications of REEs with emphasis on secondary sources such as coal and coal byproducts, iron ore tailings, apatite, and phosphate byproducts. An overview of the current state of knowledge on the various methods of REE beneficiation and extraction is covered. These methods include physical separation, as well as hydrometallurgical and bio-hydrometallurgical techniques. The application of these REE extraction techniques for enhanced recovery has been driven primarily by the unique industrial application of these important elements. This paper further explores the existing and potential environmental challenges associated with REE extraction. The authors have presented a wide array of literature, in-depth discussion of the subject, and a succinct summary of processes and relevant case studies.

Sep 23, 2020

By Sergio Estebanez, Martha Gross, Ruben Rubal, Yvonnick Rescamps, Alexandre Cochennec

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in coastal Virginia, USA will add two 1.5-mile (2.4 km) TBM bored tunnels alongside two existing immersed-tube tunnels between artificial islands. The site’s unusual constraints and the requirements of a large-diameter variable-density TBM shaped the design-builder’s decisions for handling TBM inputs and outputs, siting the TBM plant and supporting equipment, and sequencing tunnel-construction operations. This paper addresses the logistics necessary to enable key functions of the 46-ft (14-m) TBM and its ancillary equipment, including transport of most materials by barge, U-turn of the TBM on an artificial island, and delivery of materials for the second tunnel through the first one while interior structures are under construction.

Jun 13, 2021