Search Documents

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the disasters occurring in underground coal mines. As a typical case, the spontaneous combustion of broken coal left in the longwall gobs often happen which could greatly interrupt the normal mining production. Such concealed thermal event is featured as rapid development and difficulty in locating “hot” spots. If such spontaneous combustion fails to be timely prevented and controlled, a large amount of toxic gases (mainly CO) and smoke could flow and diffuse in the underground working sections, which could present safety hazards for coal miners. In this paper, based on an coal spontaneous combustion event happened in a Chinese gassy mine, the fire ratios derived from the gas composition data obtained through the tube bundle mine atmospheric monitoring system are used in determining the fire status. A comprehensive and collaborative fire extinguishing effort including inert gas injection, underground pressure balance, and sealing enhancement are made to control the fire progress. Simultaneously, the effects of such works to control the spontaneous combustion event have also been quantified using the fire ratios to justify again. Finally, the danger of coal spontaneous combustion in gob is eliminated, and the longwall panel is successfully re-opened for normal production.

May 6, 2021

By Snehamoy Chatterjee, Sanjay Kumar Palei, Smarak Das

Machine manufacturers’ recommendations on maintenance strategies of capital-intensive draglines are not always based on real data and therefore lead to losses from downtime. This paper proposes a preventive maintenance strategy for a dragline deployed in an opencast coal mine based on reliability-centered maintenance and failure-mode-effects analysis using real operational data. Reliability-centered maintenance replaced a cluster of critical failure components of the dragline while satisfying two specific conditions: (i) the components should be replaced at the earliest mean time to failure (MTTF) within the group and (ii) the time taken to replace all the parts should be equivalent to the maximum downtime within the group. Estimated threshold weightage factor identified twenty-six critical failure components for the preventive maintenance strategy, and clustering of components divided them into nine groups. In a group, the loss that is expected to occur by replacing some of the components before their failure, and the gain by reducing the overall maintenance downtime, has been explained through a cost-benefit analysis. The total net profit generated is calculated as US$200,178. This clustering activity also led to a reduction of annual downtime by 231 h, whose approximate market price as equivalent coal production costs $295,365.

May 28, 2020

By S. A. Smith-Hamm, E. A. Sarver, A. S. Cox

Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and inductively coupled plasma-mass spectroscopy (ICP-MS) was used to determine how leaching conditions affected the release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that for certain spoil materials, the SC in the leach column effluent was effectively reduced when the spoil was first leached with acidic rainwater followed by ambient rainwater, as opposed to leaching with ambient rainwater alone. This suggests that accelerated leaching might aid in the long-term stabilization of some materials.

Jan 1, 2015

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

By John Keefner, Charles Kocsis, Kyle A. Scalise

Geotechnical modeling of mines is crucial for understanding the many factors that can pose potential hazards or limit production opportunities. The process of back analyses for modeling is often used, but in many instances, the back analyses can be cumbersome and time inefficient.While thesemodels and back analyses may be accurate, these types of back analyses may not be ideal to be used at mines and by engineers because the process is so time-consuming. This paper introduces event-based back analyses that utilize prior events to create more accurate models while eliminating large modeling time because the models are back analyzed from previous events. The completed analyses supply a more detailed insight into the potential hazards at Round Mountain, an open pit operation, as well as provide a better understanding of how improper risk analysis results in missed opportunities. The more we understand about mining activities and processes through modeling, the safer and more productive mines will be.

May 24, 2021

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for the expensive large-scale tests that are currently being used. A radiant-panel apparatus was used to determine the materials’ relevant thermal characteristics: time to ignition, critical heat flux for ignition, heat of gasification, and mass-loss rate. Three thermal parameters, TRP, TP1 and TP4, were derived from the data, then developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with the thermal and ignition hazards of similar materials reported in the literature and support this approach as a simpler one for quantifying these combustible hazards. Resumen ¦ El objetivo de este estudio fue el desarrollo de un método a escala de laboratorio con el fin de clasificar los peligros de ignición y fuego de materiales comúnmente usados en minería subterránea y la eliminación las pruebas costosas y a gran escala que se realizan actualmente. Se usó un aparato de panel radiante con el fin de determinar las características térmicas relevantes de los materiales: tiempo de ignición, flujo de calor crítico para ignición, calor de gasificación y tasa de pérdida de masa. Se derivaron tres parámetros térmicos de los datos: TRP, TP1 y TP4, luego fueron desarrollados y subsecuentemente usados para clasificar los peligros combinados de ignición y fuego de materiales combustibles, de bajo riesgo a alto riesgo. Los resultados tuvieron una comparación favorable con los riesgo/peligro térmicos y de ignición de materiales similares reportados en la literatura y apoyan este enfoque como uno más simple para la cuantificación de estos riesgos combustibles"

Jan 1, 2015

By Han Zhao, FENGLIANG WU, Tong Wang

Calibrating an entire mine ventilation network model from survey data has long been considered a challenging and sometimes impractical task. This paper proposes a solution to this issue with the development of a quadratic programming optimization model. The optimization model takes the minimum modification of input resistances as the objective function, uses the mesh pressure equations as equality constraints, and incorporates the lower limits of airway resistances as inequality constraints. A two-step method is developed to solve the model, which includes finding an initial feasible solution and iteratively solving the final solution using the active set method. A computer program has been developed to implement the optimization model. To demonstrate its practicality, a study case using a 35-branch ventilation network is presented, which indicates that the solution process converges after only 57 iterations, a significant improvement over the times of trial and error, which could reach 3.4 × 1010 for the worst-case scenario. Additionally, it is shown that considering only the equality constraints results in negative resistances, while incorporating the lower limits of resistance ensures that the corrected resistances are within a reasonable range. Using the resistance corrected by the optimal model to simulate the ventilation system via traditional methods generates quantities and fan pressures that perfectly match the measured values, eliminating the tedious process of manually adjusting airway resistances repeatedly.

Jan 13, 2024

By Staff

"In 2018, the total estimated value of nonfuel mineral production in the United States increased by 3 percent from 2017 to $82.2 billion. The estimated value of metals produced domestically decreased by 4 percent, and the estimated value of indusrial minerals produced domestically increased by 7 percent (Table 1).Some idle U.S. metal mines and processing facilities restarted in 2018, including two primary aluminum smelters in Indiana and Missouri, a rare-earths mine in California and a zinc mine in New York. In contrast, four iron ore mines in Minnesota and a pelletizing plant in Indiana were shut down. Increased oil and natural gas drilling activity in 2018 led to increased production of some industrial mineral commodities that are used for oil and gas drilling, including barite and industrial sand and gravel. Production of industrial minerals primarily used in infrastructure and residential construction — including, cement, construction sand and gravel, crushed stone and gypsum — increased in 2018. Overall, mining activity trended upward for the second consecutive year because of increases in oil and gas extraction and industrial mineral mining (Table 2).Mineral industry performanceDiscussion of mine production is commonly segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as natural aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, such as crushed stone or construction sand and gravel, which have higher production quantities but are lower-valued materials. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of natural aggregates are orders of magnitude larger than those for most other mineral commodities, thus making direct comparisons based on weight meaningless (Fig. 1)."

May 1, 2019

By Jerry Dolph

In September 1855, 55-year-old Noah Spencer Kellogg and his $3 jackass named Bill discovered what was known at the time as a “blow out” of high-grade lead and silver ore. The deposit was located on the side of a North Idaho mountain high above the South Fork of the Coeur d’Alene River. The ore was later assayed at 41,141 g/t (1,200 oz/st) silver. Kellogg named his discovery the Bunker Hill Lode, after the June 17, 1775 Revolutionary War battle of Bunker Hill. A thriving pioneer settlement sprang into existence around the resulting mine’s workings and was eventually— and appropriately — named Kellogg. The peak rising hundreds of feet above the mine’s adit was named “Jack-ass Peak” after Noah Kellogg’s hairy companion.

Jan 1, 1996

By C. L. Peng, F. F. Min, S. X. Song

"Using a parameter representing the degree of hydration of particles in a liquid called hydration index I, which we derived based on Einstein’s viscosity equation, we evaluated the degree of hydration of fine montmorillonite particles in different aqueous solutions by measuring the viscosities of the montmorillonite dispersions and plotting relative viscosity against volume fraction of dry montmorillonite particles in the dispersions. We investigated the effects on the hydration of montmorillonite in aqueous solutions of (1) the type and (2) the concentration of electrolytes in the solutions and (3) pH. For the same concentration of electrolytes, the hydration index I of montmorillonite was found to increase in the order of Na+ > K+ for monovalent cations and Mg2+ > Ca2+ for divalent cations, and to decrease with increasing valence of cations in the order of Na+ > Ca2+ > Al3+. For both Na+ and Ca2+, the hydration index I first increased with increasing concentration of electrolytes and then decreased after a certain concentration. The hydration index I increased with increasing pH. IntroductionClay minerals have the distinctive ability to adsorb water molecules and hydrated cations in aqueous solutions, resulting in hydration on their outer surfaces and in their interlayer spaces. Many investigators (Jurinak, 1963; Anderson and Tice, 1971; Costanzo et al., 1982; Israelachvili, 1992) had found evidence of ice-like structures of water on clay minerals.This phenomenon of hydration plays an important role in the dispersion and sedimentation of clay minerals in aqueous solutions. To understand clay hydration, numerous experimental and simulation studies have been carried out since 1933, including the recent ones of Hawkins and Egelstaff (1980), Skipper et al. (1995), Karaborni et al. (1996), Salles et al. (2013) and Morrow et al. (2013). Among the factors that can influence a clay mineral’s hydration characteristics are chemical composition, type and degree of isomorphous replacement in its structure, and number and nature of associated exchangeable cations."

Jan 1, 2015

By J. H. Kim

Since the Hardy Cross numerical algorithm was applied to the solution of mine ventilation networks, there have been numerous developments in ventilation network analysis procedures. The Newton-Raphson method, the linear theory method, and the second-order approximation method are three of the additional approaches that have been applied. The efficiency of a ventilation network analysis procedure depends not only on the method of solving the system of equations derived from ventilation networks, but also on the method of deriving the equations through selection of the meshes. This paper investigates the impacts of three mesh selection methods on the efficiencies of four ventilation network procedures. The minimum-resistance spanning tree method is the most popular procedure for selecting meshes. The shortest-path method was suggested by Epp and Fowler (1970) for improvement of the Newton-Raphson method. The minimum-resistance-path method is suggested here as the third method of selecting meshes. The effects of these three methods on the Hardy Cross method, the Newton-Raphson method, the linear theory method, and the second-order approximation method are analyzed in this paper. These network analysis methods have been summarized in the paper by Kim and Mutmansky (1991).

Jan 1, 1992

By R. Lai

This paper describes the application of a cyclonic flotation column (CFC) for coal cleaning. A CFC makes use of centrifugal force to create a density gradient in a column to augment the froth flotation process. In a CFC, a series of angular helical inserts is attached to the wall of a conventional column and coal slurry is mixed with a series of impellers attached to a central shaft. The hydrophobic froth concentrates near the center shaft and moves upward, while the relatively heavy hydrophilic particles concentrate near the wall and are guided downward by the helical inserts. Results of pyritic sulfur removal from an Upper Freeport coal during CFC flotation are discussed in this paper.

Jan 1, 2000

By J. Best, K. Gallant

This paper explores the age-old concept of mine-mill reconciliation from a new perspective. Advances in reconciliation processes have been slow to materialize because in the quest for “rightness”, engineers, geologists and metallurgists have become entrenched in their viewpoints, dutifully performing to the metrics and expectations imposed upon them by the siloed organization. Moreover, reconciliation has not been viewed as a primary value creator, but an accounting non-value added task. In reality, the knowledge from reconciliation can significantly enhance yields. Critical review of the direct variables (tons, grade, etc.) and other less-obvious variables (incentives, communication, etc.) reveal a complex web of barriers to be cleared by management in order to realize benefits. Also, mineralogical reconciliation methods may offer renewed faith in the process.

Jan 1, 2004

By L. Thompsen

High-pressure grinding rolls (HPGR) offer capacity increases, savings in operating costs and metallurgical advantages. The first installation of the Polycom HPGR in a copper ore treatment plant occurred in July 1995 at Cyprus Sierrita’s mining complex near Green Valley, AZ (Fig. 1). Until that time, the benefits this technology offers for copper and gold ore were only demonstrated on testwork. In other industries, such as diamonds, HPGR have proven to be reliable in industrial-scale plants and have set a new standard for this kind of ore treatment plant. HPGR are also successfully used for the comminution of coal, blast furnace slag and in cement and pelletizing plants. The installation at the Cyprus Sierrita Mine should prove the economical benefits in commerical-scale copper mining, confirming the results of comprehensive testwork(Fig. 2).

Jan 1, 1996

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented. Applications in the industrial plant and in the research field are discussed.

Jan 1, 1990

By J. Drelich

The wetting behavior of liquid polymers at solid surfaces and the adhesion forces involved at polymer-filler interfaces should always be considered in the fabrication of high quality polymer composites, including those made with mineral fillers. Spontaneous polymer spreading over the filler surface is a basic condition in the fabrication of the polymer-mineral composites. In this regard, the wetting and adhesion characteristics of polymer-mineral systems are reviewed in this contribution. It appears that several aspects of wetting phenomena at mineral filler surfaces are not well described in the literature and require further systematic study. Specifically, it is clear from this review that efforts should be made to determine the effects of mineral surface contamination (including surface hydration) on wetting and adhesion phenomena, and to determine the wetting characteristics of molten polymers at mineral filler surfaces. It is expected that any improved fundamental understanding of wetting and adhesion phenomena for the polymer-mineral composites will provide the basis for further technological development.

Jan 1, 1995

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

The Jiboia heavy mineral sands deposit is a new discovery associated with the São Francisco River delta on the northern coast of Sergipe state. The identified resources are part of the much larger mineralized trend. Mineralization is hosted in paleodunes deposited on Holocene marine terraces (Fig. 1). The dunes are up to 30 m above sea level, and mineralization occur from 6 m above sea level upward. The main ore minerals constitute pseudorutile, ilmenite, zircon, rutile and monazite. This work presents a thorough characterization of the mineralogy and granulometric distribution of the Jiboia orebody.

Apr 1, 2024

By Ebrahim Ghasemi, Mohammad Hossein Kadkhodaei, Mosareza Jalilian

Entry-type mining methods, such as cut and fill method, play a significant role in underground mining, and they are still suitable methods for extracting deposits with irregular shapes and with weak host rocks. In these mining methods, the stability of the open spans is important for improving worker safety and increasing ore recovery. This study focuses on the application of six data mining classification methods, namely multinomial logistic regression (MLR), classification and regression trees (CART), logistic model tree (LMT), decision tree (J48), multivariate adaptive regression spline (MARS), and gene expression programming (GEP), in order to develop predictive models for stability assessment of underground entry-type excavations. For this purpose, a database containing 399 case histories of entry-type excavations from seven Canada underground mines was used. These models predict the stability status of entry-type excavations based on two input parameters, dimensions of the span and rock mass rating (RMR). The performance of developed models was evaluated using six performance metrics namely accuracy (ACC), sensitivity (SE), precision (PR), Matthew’s correlation coefficient (MCC), area under the receiver operating characteristic (ROC) curve (AUC), and performance index (PI). The results showed that all developed models can be used to predict the excavation stability, but the comparison of models indicated that the J48 model provides the highest performance with ACC = 0.900, SE = 0.869, PR = 0.922, MCC = 0.835, AUC = 0.891, and PI = 4.417. Thus, the proposed J48 model can be applied to identify the susceptibility of span instability in the entry-type mining, and if instability has been predicted, the necessary measures, including the use of suitable support systems, can be considered to reduce the casualties resulting from span instability.

Feb 26, 2024

By Lyman File

This paper discusses the overall challenges to construct a two-lane highway tunnel located in southwestern Colorado on U.S. Highway 160 for the Colorado Department of Transportation by the Kiewit Western Company. The purpose of this project is to provide the excavation and temporary support for a highway tunnel 280 m (916 feet) long. The tunnel cross section is 14.3 m (47 feet) wide by 8.5 m (28 feet) high, 105 m2 (1,130 SF).Construction methods include conventional drill and blast excavation with rockbolt and shotcrete ground support. This unique tunnel is being constructed under alpine tunnelling conditions and in the immediate vicinity of active highway traffic.

Jan 1, 2003

By Yuemin Zhao, Wenxuan Liu, Maoming Fan, Zhanyuan Long

"Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium and phosphorus. These coalassociated elements are significantly enriched in coal combustion byproduct fly ash because the majority of the main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main element oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides and unburned carbon.Chinese coal fly ash usually contains about 5 to 15 percent of unburned carbon, which are generally chars with irregular shapes and wide particle size distribution. In addition to unburned carbon, XRD analysis of four Chinese fly ash samples from Liaoning, Shanxi, Guizhou and Shandong provinces indicates that the fly ash samples are composed of minerals such as quartz (SiO2), mullite (3Al2O3.2SiO2 or 2Al2O3.SiO2), hematite (Fe2O3), maghemite (gamma form of hematite, ?-Fe2O3) and magnetite (Fe3O4). The mullite and quartz particles are usually present as spherical particles because they are formed by melting clays, feldspars, quartz, calcite and other common minerals in coal during coal combustion. The silicate particles have usually entrapped gas to yield hollow spherical particles because their lower melting point facilitates gas entrapment.The iron oxides are usually spherical also. The magnetite (Fe3O4) is derived from pyrite (FeS2), hematite (Fe2O3), siderite (FeCO3) and limonite (2Fe2O3.3H2O) in the coal. Maghemite (?-Fe2O3) is formed by dehydration of the mineral hydrohematite (?-FeO(OH)) and/or oxidation of magnetite (Fe3O4) during coal combustion. Maghemite (?-Fe2O3) and magnetite (Fe3O4) are strongly magnetic, so they are recovered from Chinese coal fly ash and widely used for coal processing in China (Fan et al., 2005, 2000)."

Jan 3, 2018