Search Documents

By Richard Weinstein, Richard Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Because of the environmentally friendly nature of dry jig plants, installation permits are often measured in days, not months. There has also been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But air jigging is not right for every application. There are limitations due to particle size, particle shape, moisture and near gravity content. This article explores the evolution of dry jigging. It reviews parameters important for determining the suitability of dry jigging. It also compares historical performance data as measured by imperfection, against results from modern dry jigging technology. The article also presents data from modern dry jig installations.

Jan 1, 2007

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents preliminary test results obtained with a 0.38 kg/s (3000 lb-hr) beta prototype MagMill™. In processing Upper Freeport coal the beta prototype recovered 82% of the weight of the feed and 91% of the heat content while reducing the potential emissions of sulfur, kgSO2/GJ(lbSO2/MBtu), by 61%. Pyritic sulfur in the MagMill™ product was reduced by 78% compared to that in the feed. For all runs, the mill product was controlled between 70 to 80% finer than 74 µ particle size. Recoveries of mercury, arsenic, and selenium ranged from 35 to 45% of that in the feed. Power draw was reduced by 26% and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2000

By B. Oraee

Accurate estimation of equipment costs is a key factor in feasibility study and evaluation of design alternatives of mining projects. In this paper, capital and operation costs of backhoe loaders are estimated using multiple linear regression (MLR), based on principle component analysis (PCA). These cost functions are consisted of five independent variables; bucket size, digging depth, dump height, weight and horse power. The MLR is conducted in two steps. At the first correlation between independent variables is omitted using PCA technique. Thereafter, MLR functions are established using selected significant PCs and total cost functions are constituted as functions of initial variables. At the end, accuracy of functions are evaluated using mean absolute error rate method.

Jan 1, 2011

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

All aspects of precious metals processing were featured at a symposium held Oct. 3-6, 2007, at Loews Ventana Canyon Resort in Tucson, AZ. Although billed as "Precious Metals Processing: Advances in Primary and Secondary Operations," the symposium also looked at economic, regulatory and environmental issues affecting the precious metals industry. The symposium was sponsored by SME; The Minerals, Metals & Materials Society (TMS); and the International Precious Metals Institute (IPMI). It included workshops, technical presentations, guest speakers and social activities. Mining industry management, process engineers, equipment manufacturers, consultants, metals marketers, academics and others involved in the precious metals industry attended the conference. Needless to say, with gold nearing $25.721g ($800/oz) and platinum pushing $41.801g ($1,300/oz) at the time of the meeting, the mood among the attendees could not have been more positive. The symposium was privileged to have Father Ernest S. Sweeney, professor of Latin American History at Loyola Marymount University, as a guest speaker. Sweeney, a Jesuit priest, provided a colorful account of the history of mining in Arizona and the surrounding region of North America (Fig. 1). He described the importance of the mining industry and said, "To go down into the bowels of the earth to extract its riches for the benefit of all of us is an awesome task deserving our sincere respect and gratitude." However, he warned the industry that: "The ever increasing de¬mands on the mining community for the protection of the environment calls for endless efforts to maintain ethical standards in a business filled with risk, uncertainty and frustrations." Sweeney noted that the Spanish conquest of the Americas was driven by the three fundamental motives of "God, glory and gold." He noted that gold was the basic, most powerful driving force of the conquest and occupation of the Spanish empire. The first European to explore Arizona was the Franciscan missionary Marcos de Niza. He came to Arizona in 1539 in search of the fabled Seven Golden Cities of Cíbola. Sweeny noted that Spanish explorers were consumed, as Cortes himself described it, "with a burning fever that only gold could cure." Sweeney told the story of some of these early explorers, including Francisco Vázquez de Coronado who "mounted an expedition in pursuit of gold and rich empires to conquer." Coronado passed through Arizona and discovered the Grand Canyon. "Coronado returned to Mexico exhausted, bankrupt and disillusioned, but with a wealth of new knowledge of the borderlands of the Spanish empire," said Sweeney. He then described the colorful history of early gold, silver and copper exploration and mining in Arizona, including the famous tale of the Lost Dutchman's Mine. In a luncheon address, David Kanagy, SME's executive director, introduced the attendees to the upcoming OneMine. org Web site. Kanagy told the audience" One-Mine.org will be a collaborative digital library that will

Jan 1, 2008

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002, after the development of models for magnetic separators, hydroseparators and fine screens. A project funded the US Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Mittal plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2008

By J. Torma-Krajewski, C. Hipes

Many mining companies apply ergonomic principles, but it is done either informally and/or reactively. Examples of an informal approach include replacing worn equipment, such as seats, with models that have ergonomic features, or modifying tasks to eliminate safety hazards that will also reduce risk factor exposures that may result in musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/equipment after an MSD occurs. Neither one of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper will discuss how Vulcan Materials Company applied ergonomic principles and the interventions implemented to reduce risk factor exposures.

Jan 1, 2007

By David Caiden, Geoffrey Fosbrook, Jaidev Sankar, Donald Phillips, Jon Hurt, Anil Parikh

This paper will cover the progress being made on Phase 1 of New York’s Second Avenue Subway line. It will include a description of construction progress on the first contract to be let, which consists of a 248 m (815 ft) long launch box, 3.9 km(2.4 miles) of TBM tunnels and a tunnel sump; the packaging strategy for the remaining work; and the progress through Final Design of the remaining packages, including the two large span rock cavern stations.

Jan 1, 2007

By Richard Hanke

Tunnel construction on the Brightwater Conveyance System?s East and Central contracts required ground modifications of the existing site soils, comprised of sandy alluvium to very dense glacial till, to assist with both hand-mined and TBM tunneling operations at vertical access shafts. The ground modification program was completed with a modified double fluid jet grouting system to construct continuous overlapping soilcrete columns to depths up to 94-ft below existing grade. This paper presents the sequence and methodology for the ground modification work and capabilities of jet grouting for structural support and groundwater control in the challenging soil profile present at the Brightwater Conveyance System Project.

Jan 1, 2008

By Paul Bartos

Operations at the Sweet Home Mine transformed the mineral specimen industry, not only in the development of new innovative extraction techniques, but also in the fields of sample preparation and marketing. Principally as a result of the activities at the Sweet Home Mine, there is now a better appreciation of minerals and the market they encompass. Individual Sweet Home rhodochrosite specimens have been sold for more than $1 million, with many more in the five- and six-figure dollar range. This article is a review of the Sweet Home operation, with emphasis on its extraction techniques. District history The Sweet Home Mine is located within the Alma mining district in the Mosquito Range of central Colorado, approximately 6 km (3.7 mile) northwest of the town of Alma at the base of the Red Amphitheatre in Buckskin Gulch at an elevation of 3,440 m (11,286 ft). Other nearby mining districts include Climax, Leadville, Breckenridge and London. All are considered part of central portion of the Colorado Mineral Belt (Fig. 1).

Jan 1, 2007

The Functional Performance Equation for ball milling circuits allows us to isolate the circuit classification system efficiency (CSE) from the mill?s grinding performance. The factors which affect circuit CSE are reviewed, with emphasis on water usage at the classifiers. It is shown that manipulation of such water usage can be carried out to improve plant grinding circuit efficiency, at times by more than 30 percent.

Jan 1, 2009

By K. Hanumantha Rao, A. Nayak, K. S. Narasimhan, S. N. Mahapatra

B.A. Hancock It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rupture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding-classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective flocculation separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 9, 1986

By J. D. Morgan

In the first half of the year, lessening of cold war tensions was welcome. But Iraq's invasion of Kuwait in the second half led to the Persian Gulf War in January and February 1991. This caused an oil shock that dampened the economy. So the US gross national product rose only 0.9% to $5,463 billion (US billion = 109). The buildup of military forces in the Persian Gulf area focused greater attention not only on petroleum but also on other strategic materials. The Department of Defense continued to review stockpile goals and to upgrade several mineral materials. In addition, the Bureau of Mines continued to maintain the standby Emergency Minerals Administration. The Defense Production Act, which authorizes priorities, alloca¬tions and supply expansion, lapsed on Oct. 20. So the Selective Service Act of 1967 became the authority for assuring that orders of the armed forces and defense atomic-energy programs were given priority treatment. Consumer demand strongly affects mining worldwide. US citizens carry significant debt, and large stocks of housing and consumer goods are already in place. Some 250 million persons have 188 million licensed motor vehicles and 100 million dwelling units. Consequently, new car production fell 11 %, to 6.1 million units. Truck and bus production fell 8%, to 3.7 million units and new private housing starts fell 13% to 1.2 million units.

Jan 1, 1991

By Brendan Reilly, Jon Isaacson, Paul McDermott

Kenny/Shea JV is constructing the water intake tunnel for the new Elm Road Generating Station, a supercritical coal-fired power plant in Oak Creek, Wisconsin, being built by Bechtel Power Corporation. The intake tunnel system consists of a temporary mining shaft, pump house and intake channel riser shafts, and four lakebed intake shafts. An 8.33 m diameter, 2,800 m long TBM mined rock tunnel is being constructed to connect the shafts. The intakes are located 2.4 kilometers offshore in Lake Michigan. The shafts and tunnel are being constructed in glacial tills and Silurian Dolomite. The estimated tunnel completion is December 2007.

Jan 1, 2007

By Michael Harris, David Mosch

The numerous small high grade gold and silver deposits of the Front Range Mineral Belt have been uneconomical because of the high costs of mill construction, transportation, and smeltering. Processing of these ores must be simple, cheap, with satisfactory recoveries, and be environmentally acceptable. Vat leach with direct electrolytic recovery satisfies these parameters. A battery of testing was conducted utilizing bottle and bucket tests. A five ton vat leach with direct electrolytic recovery gave excellent results while a five ton heap leach proved impractical due to channeling.

Jan 1, 1987

By V. Bush, T. G. Killingsworth, E. P. Ruffel

Effective and sustained corporate energy management programs are becoming a necessity for energy users as electricity deregulation laws are enacted on a state-by-state basis across the country and environmental regulations pertaining to emissions become more prevalent. The “Total Energy Asset Management” (TEAM) approach has been developed to assist energy end users with the development and implementation of corporate energy management programs designed to reduce energy risks and increase energy cost savings. This paper highlights the ways in which this approach can be applied to the mining industry while minimizing initial program implementation costs and increasing potential program benefits. Nearly the entire mining industry has become very focused on identifying opportunities to reduce costs per unit of yield. The industry as a whole has increasingly faced pricing pressures in large part due to the effects of global competition. The result of international marketplace participation and the emergence of higher efficiency recovery techniques have resulted in flat or even decreased prices for mining products. Thus, opportunities to reduce costs are actually opportunities to gain a competitive edge over similar mining operations. Due to the energy-intensive nature of many mining operations, the costs associated with energy are often a substantial percentage of operating costs. Therefore, it becomes very important to develop the corporate mentality that energy is an asset whose use should be optimized globally. In addition to the cost benefits of the TEAM approach, other benefits may occur such as reductions in facility greenhouse gas emissions.

Jan 1, 2002

By Bradford F. Townsend

A study was made on six collapses that occurred during large-diameter tunnelling through weak sedimentary rocks and soil using SES methods in three stages?top heading, bench and invert. The collapsed lengths are between 20 m and 277 m. The collapses were re-mined using essentially the same tunnel-ling method with larger excavation profiles to accommodate the designed remedial measures consisting of ground treatment, pre-support and stronger initial support/outer lining required to carry higher ground loads acting in the collapsed lengths. The paper presents information on the collapses and the design and execution of the remedial measures.

Jan 1, 2008

By D. Brün, T. W. Nattkemper, T. Kuhn, T. Schoening

Underwater exploration for marine resources using camera-equipped devices (OFOS, ROV, AUV) is receiving growing attention. This development is creating a continuously growing pile of digital underwater images leading to a serious bottleneck in the analysis. However, any harvesting strategy must be coupled to an efficient and effective assessment of the biodiversity in the area of interest and in nearby control areas. To integrate manual image and computational image interpretation on different levels (i.e. regarding geology and environmental sciences and taxonomy), sophisticated software support is required, which is not yet offered explicitly, neither by commercial software companies nor by academic or other publicly founded institutions. Here, we present the first version of a new digital asset management system that offers functionalities for easy data management, sharing, manual annotation and integration of computational modules for image enhancement/pre-processing and interpretation. The functionality is demonstrated with data from the CCZ provided by the BGR Hannover.

Sep 1, 2014

The National Mining Hall of Fame will induct five mining greats on Saturday, Sept. 17, 2005 at the Museum Convention Center in Leadville, CO. The 18thAnnual National Mining Museum and Hall of Fame Induction Banquet will begin with an open house and reception at 5:30 p.m., followed by the dinner and program at 7 p.m. The five inductees are Nathaniel Peter Hill, John Munro Longyear, John McDonald, Julius Eckhardt Raht and John Dennis Ryan. Nathaniel Peter Hill (1832-1900) built the first successful smelting operation in the Rocky Mountains in1867 at Black Hawk, CO. From 1879 to 1885, he was a U.S. senator. He also taught courses at the Colorado School of Mines.

Jan 1, 2005

By Adeyemi Adesina, Subhabrata Mishra, Syed Mohammed Mustakim, Malaya Kumar Jena, Shaswat Kumar Das

Utilization of low-grade manganese ore adopting the carbothermic reduction roasting process is a proven method to produce high-grade manganese ore. To minimize industrial waste and protect the environment, gas cleaning plant sludge (GCPS), which is a solid waste from steel industries, was employed as a reductant to perform the reduction roasting process. The optimum conditions to carry out reduction roasting of the low-grade manganese ore were found to be: a roasting temperature of 950 °C, a residence time of 2 h, 40% GCPS as reductant, and magnetic separation at 5000 G for a manganese ore size of –10 mm. A lowgrade manganese ore comprising Mn grade 31.27% and Fe grade 19.78% having a Mn/Fe ratio of 1.58 containing a high silica content of 26.48% was used for the carbothermic reduction roasting having mineral phases of pyrolusite (MnO2) and hematite (Fe2O3) as found from XRD. The gangue minerals were separated during the magnetic separation, and the upgraded product was obtained, which reached a maximum value of TMn 49.5% with RMn 76.55% and TFe 62.19% with RFe 42.51%. In the study, activated charcoal (AC) was also taken as a reductant for comparative analysis; the experimental results revealed that GPCS performed better than that of the AC, showing potential to be used as a reductant in metallurgical industries. However, the resultedMn/Fe ratio was very low for the reduced sample; therefore, it can be used for smelting along with high-grade manganese ores as a feed.

Mar 5, 2021