Search Documents

By Z. L. Xue, J. L. Li, X. Y. Wang

"In low-carbon energy-efficient basic oxygen furnace (BOF) steelmaking processes, limestone partly or completely replaces the active lime. The effects of limestone calcination temperature (1200–1500°C) and time (5–15 minutes) on lime reactivity and CaO grain size were investigated. The reactivity was evaluated by titration with hydrochloric acid, and the CaO grain size was analysed using scanning electron microscopy. The results revealed that for calcination temperatures higher than 1300°C, the reactivity reached a maximum and then decreased . The higher the temperature, the earlier the peak of reactivity appears. The CaO grains grow with increasing temperature and time, which leads to the decrease of reactivity. Notably, the effects of temperature on CaO grain size and reactivity are more marked than that of time. To obtain active lime calcined at ultra-high temperature by flash heating, the calcination conditions should be 1300–1400°C for 10–15 minutes, or 1400–1500°C for 8–10 minutes. IntroductionLime is one of the most important slag-making materials for dephosphorization and desulphurization in the basic oxygen furnace (BOF) steelmaking process. The reactivity of lime is a measure of its capability to take part in slag-making. Lime having a reactivity of more than 300.0 mL (4 N HCl), determined by hydrochloric acid titration is generally referred to as active lime (Rusjan et al., 2007; Zeman, 2008). At present, the active lime used for BOF processes comes primarily from a kiln or shaft kiln, where limestone is preheated at 700– 900°C, and then calcined at 1050–1200°C (Drenhaus et al., 2010; Oates, 2007)."

Jan 1, 2016

By K. Esmeli, A. Ozkan

The enhancement of shear flocculation of a galena suspension by ultrasound in the presence of sodium isopropyl xanthate and potassium ethyl xanthate was investigated by studying the effects of surfactant concentration on flocculation efficiency, contact angle, and zeta potential. Strong flocculation was obtained under alkaline conditions (pH > 9) and a high ultrasound power level (150 W). Although the ultrasonic treatment increased the negativity of the zeta potential of the galena particles, this did not decrease the flocculation efficiency, thereby showing that the hydrophobic interactions between the particle were stronger than the electrical double-layer repulsion resulting from xanthate adsorption. The findings indicate that the ultrasonic treatment promoted the adsorption of surfactants onto the mineral surfaces.

Jul 5, 2023

By G. M. Evans, S. Mitra, A. V. Nguyen

As an alternative to the conventional flotation method, there has been continual research in an effort to enhance base metal ores and combustibles recovery using ultrasonics. These studies however were largely limited to the pre-treatment of ores for the removal of surface contaminants while the effect of ultrasonics on the bubble and pulp-phase interactions remained somewhat unexplored. Noting this deficiency, this study aimed to investigate the mechanistic effect of an ultrasonic field in an impeller less flotation cell specifically focusing on the bubble-particle interaction dynamics. A lab-scale flotation cell (capacity 1 litre) was designed, involving a vertically oriented ultrasonic probe (20 kHz, rated at 1.2 kW) and operated in the output power range from 1 to 20% with continuous liquid recirculation. Particle suspension was achieved by the combined action of recirculation and ultrasonic pulses. Interactions of coarse size glass ballotini particles (D32 = 314 μm) with bubbles (< 1 mm diameter) in the presence of a surfactant were studied, using high-speed imaging. Application of an ultrasonic pulse in the aqueous medium resulted in the generation of numerous microbubbles which increased with increasing input power and duration of the ultrasonic pulse time. Such periodic pulses introduced at a high level of turbulence in the pulp phase facilitated adequate bubble-particle contacts. Microbubbles played a key role in forming particle clusters which were observed to be floatable even in the absence of any carrier bubbles. When carrier bubbles were introduced, some of these particle clusters attached to the bubble surface and conveniently floated. It was noted that a favourable state of bubble-particle interaction was achievable to produce stable bubble-particles aggregates by suitably controlling the input power and period of the applied ultrasonic pulse. Keywords: Flotation, bubble-particle interactions, collision, attachment, detachment, ultrasonic pulse

Jan 1, 2020

By M. Kumral, S. Li, M. Balci, Z. Shao

Main haulage roads play an important role in the performance of underground mines because of the cost of transportation of the extracted ore, equipment, and workers. During mine development, these roads are designed through manual tools or CAD-based software. However, the optimisation of these roads is still a complex problem due to some constraints such as minimum turning radius and maximum gradient. By utilising Dubins path theory, three elevation cases; namely low, medium and high are defined, considering gradient constraint as well as the minimum turning radius in a three-dimensional space. The shortest path between two points can then be found by the three-dimensional Dubins path algorithm with elevation constraint. As a further step, a three-dimensional Dubins path algorithm with elevation constraint for multiple points is also developed for multi-point cases. The effectiveness of these algorithms is tested through case studies in order to determine the optimal path between different points.

Sep 1, 2021

By J. Engelbrecht

Understanding the deportment of minerals in size fractions has already led to improvements in the flow sheets for platinum minerals beneficiation. There are, however, more potential changes in the flow sheets that may improve the recovery of platinum group metals or reduce the costs of beneficiation before refining. Based on known technology of pre-concentration, milling, gravity concentration, flotation, and magnetic separation a number of potential alterations or additions can be considered and motivated based on the mineral deportment in size fractions.

Jan 1, 2012

By T. M. Louw, L. Auret, S. M. Bradshaw, F. F. Noelle

Modern industrial processes undergo frequent process state shifts due to changes in demand, feedstock or maintenance operations. Multimodal continuous process monitoring is therefore required for effective plant operation. Steady state analysis is a key component in effective multimodal monitoring. Various issues still remain in determining the starting and ending times of transition states. High dimensionality of process data is a characteristic that makes it difficult to select variables to consider when conducting steady state analysis. In order to address these problems, steady state detection on the principal component space is proposed. First, data undergoes principle component analysis to reduce dimensionality, then existing multivariate steady state detection algorithms are applied on the principle component scores. A novel algorithm, threshold PCA-SSD, is proposed and compared to an existing technique for steady state detection. The algorithms are investigated on high dimensional synthetic data Keywords: Multimode process, steady state detection, principle component analysis

Jan 1, 2020

By G. Mucsi, F. Kristály, R. Szabó

Kaolin is one of the most important ingredients in porcelain manufacturing. Its main phase is clay mineral containing aluminum hydrosilicate, namely kaolinite. Beside kaolinite it also contains quartz, illite and feldspars, which impair its applicability. Kaolin is a non-reactive material, but metakaolin can be produced by heat treatment (calcination) of kaolin, which is also used by the cement and concrete industry due to its latent hydraulic (pozzolanic) properties. Beside thermal activation, reactive materials can also be produced by mechanochemical activation in general. This paper deals with the mechanochemical activation of kaolin. The raw material was classified into various size fractions, then ground in a batch stirred media mill under varying circumstances (residence time, circumferential velocity). After grinding, the structural changes of the products were investigated by X-ray diffractometry (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). In addition, the particle size distribution of the ground material was determined by laser scattering. As a result of the grinding experiments and analytical measurements of the products, it can be clearly seen that reactivity of kaolin can be improved significantly by mechanical activation in a stirred media mill, but due to its high energy density the circumstances were optimised carefully to avoid aggregation. Keywords: Kaolin, grinding, stirred media mill, mechanical activation, material structure

Jan 1, 2020

By S. Liaghat, J. Rosenkranz, P. Semsari Parapari, S. Chehreh Chelgani, A. Tohry

It is commonly accepted that the energy consumption for comminution within mineral processing is responsible for around 3% of the global electrical energy usage. However, it was clearly noted that inside mills, less than 1% of this energy efficiency is actually consumed for particle size reduction. Therefore, monitoring of grinding parameters and modelling of product particle size distribution (e.g. characterised by the 80% passing size P80) play an essential role in operating costs of a mineral processing plant. Several empirical models have been introduced for the prediction of the P80. Since in the industrial scale usually a few numbers of grinding variables are monitored, these models cannot identically be used in plants. In addition, these empirical models do not always indicate the magnitude of correlations between milling variables. This study proposes to introduce the Hilbert-Schmidt independence criterion (HSIC) as an intelligent model for exploring linear and nonlinear relationships between grinding variables and P80 for an industrial scale data assessment. HSIC can rank variables based on their importance and help to select the most effective one for the generation of predictive models. HSIC modelling through various monitored grinding variables (ball charge, feed input rate, F80, power draw and work index) of an industrial plant indicated that F80 as a feed property has the highest effect on P80 of the ball mill products. Modelling results highlighted that the P80 can be accurately predicted, based on effective variables by using a HSIC model. These outcomes showed that HSIC as a powerful modelling tool can assess the relationships between monitored grinding parameters, select the most effective grinding parameters and satisfactorily predict the P80. Keywords: Product particle size, variable importance measurement, Hilbert-Schmidt independence criterion, mill charge

Jan 1, 2020

By M. Rudolph, A. D. Renno, H. Wu

In this study, synthetic pure cassiterite and cassiterite doped with Fe were successfully produced by sintering. Their crystal structure and chemical compositions are characterised by optical microscopy, X-ray powder diffraction (XRD) as well as scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) based chemical composition analysis. The electrostatic behaviour of synthetic and natural cassiterite was studied by electrophoretic measurements. Their floatability was studied by microflotation with two types of anionic collectors. Results show that the cassiterite floatability with these collectors behaves differently and lead to two opposite results: Natural cassiterite (enriched with Fe) > undoped pure SnO2 by using sulfosuccinamate (Aerosol® 22) Undoped pure SnO2 > Fe3+ doped > natural cassiterite (enriched with Fe) by using styrene phosphonic acid (SPA). Keywords: Synthetic cassiterite, lattice impurities, flotation, zeta potential, Aerosol® 22, styrene phosphonic acid

Jan 1, 2020

By J. O. Mogalanyane, N. Naudé, A. M. Garbers-Craig

The fines produced is not suitable as feed material for the subsequent rotary kiln and the electrical arc furnace. The need for briquetting the ferronickel ore is premised on the minimisation of fine particles in the rotary kiln as well as improving charge permeability in the furnace, and improving overall process safety. Briquetting may be defined as an agglomeration method in which fine particles are compressed under pressure. It consists of three different technologies: vibropressing, roller pressing and stiff extrusion. The current study focuses on evaluating the performance of ferronickel briquettes generated, using roller-pressing technology. Physical properties, chemical properties and metallurgical properties of the briquettes were used to evaluate their performance and quality. Standard ISO tests for iron ore pellets were used. Size degradation as a result of reduction was measured using the ISO 4696-1 test. The decrepitation of the briquettes at the point of entry into the rotary kiln was evaluated using the ISO 8371 test method at a temperature of 700oC. The degree of reduction was evaluated using the ISO 4695 test procedure. Average green briquette compressive strength of 559 N was reported at a moisture content of 16% with an average drop number of 19.1. Increasing the moisture content has a detrimental effect on both the compressive strength and the green briquette yield. The drop number is expressed as the number of drops until breakage, when a briquette is dropped from a 1 m height, decreased with an increase in moisture content. At a moisture content of 16% an average green briquette yield of 85.1% was reported. Keywords: Ferronickel briquettes, moisture content, curing conditions, physical properties, chemical properties

Jan 1, 2020

By D. Saramak, T. Gawenda, A. Stempkowska, Z. Naziemiec

The aim of the paper is to discuss the possibility of producing aggregates with an increased content of regular particles, as well as to present a method of aggregate production which has not previously been used in the industry. Traditional aggregate production circuits require the application of three or four grinding stages (depending on the particle size of the feed), but for fine particle fractions of aggregates, irregular grains occur on average with a content of 10%. The innovative technological circuit can produce the aggregates with the content below 3%, even in a single- or two-stage crushing circuit. Downstream jig beneficiation of such prepared material results in higher separation sharpness, lower probable error index (Ep) and imperfection (I). Keywords: Aggregate production, jig beneficiation, mineral processing, raw materials

Jan 1, 2020

By D. Minson, G. Lindner, S. Miskovic

Thickening is an essential process in the mining industry and currently one of the most costeffective technologies for recovering water from tailings streams. Improved performance of thickeners can lead to significant energy savings, and increased recovery of water close to the mill. Its performance is directly affected by the rheological properties of slurry at the raking zone. To further understand the dynamics of slurry inside thickeners, a multiphase particle-in-cell method (MP-PIC), is used to investigate its behaviour on a sliding channel. Parameters like particle-size distribution (PSD), rheological properties, and domain discretisation were benchmarked to study its influence on highly dense flows. The slurry concentration by weight of the samples ranged between 60 to 70% of solids by mass, under which conditions it is known to behave like a non-newtonian fluid. An experimental flume, 0.2 m wide and 2 m long, was used for validation under different angles and slurry composition. Visual analysis of the slurry height and shape, as well as velocity measurements, were compared with numerical data. The preliminary results show the ability of MP-PIC method to represent different types of highly dense flows, while still being computationally affordable and practical for industrial use. Keywords: High density thickener, CFD, MP-PIC, multiphase-flow

Jan 1, 2020

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By O. T. Konina, V. A. Masloboev, A. V. Svetlov, E. A. Krasavtseva, D. V. Makarov, A. A. Goryachev

Dusting phenomena have been examined at the tailings storage facility of Apatit JSC Kirovsk, a mining operation located in the far north of the Russian Federation. The material composition of the tailings was identified. Existing dust suppression methods were examined. Field observations were undertaken and official data was obtained from the Murmansk Administration for Hydrometeorology and Environmental Monitoring, and analysed. A database was built for forecasting dusting according to critical scenarios in order to estimate the peak MPCs of suspended solids in the atmospheric air. Mitigation measures were formulated and recommended to the mining operation. Keywords: Mineral dust particles, apatite-nepheline ore concentration tailings, suspended solids MPC, climate change

Jan 1, 2020

By D. Hu, J. Xu, N. Liao, C. Wu, J. Ye

The vertical stirring mill’s fine grinding equipment is affected by the operating conditions during the grinding process. The grinding media has a great influence on the energy consumption and particle size distribution. This paper investigates the fine grinding performance of nano-ceramic balls and steel balls of the same weight for magnetite by a wet grinding process in a vertical stirring mill, where 15 mm nano-ceramic balls and 12 mm steel balls are used as grinding media to carry out batch grinding tests. We have observed that the newly qualified particle content of the nano-ceramic balls is higher than steel balls of the same weight at the same specific energy. The reason may be the advantage of a greater surface area and volume filling rate with the nano-ceramic balls. Moreover, the specific energy of nanoceramic balls is less than steel balls of the same weight under the same grinding fineness. In addition, energy efficiency indicates that the nano-ceramic ball has a higher energy efficiency than a steel ball of the same weight. This is due to the light bulk density of nano-ceramic balls. The application of a nanoceramic ball in a vertical stirring mill will improve iron ore grinding performance. Keywords: Steel balls, nano-ceramic balls, vertical stirring mills, fine grinding, particle size distribution, energy consumption

Jan 1, 2020

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By M. Seerane, R. Machaka, P. Ndlangamandla

"Metal injection moulding (MIM) is a near-net-shaping powder metallurgy technique suitable for the cost-effective mass production of small and complex components. In this paper, the effects of the metal powder particle size on the final properties of 17-4 PH stainless steel are reported. Three different particle sizes (d50 33.0, 7.91 and 4.04 µm) were used to prepare the injectable MIM feedstocks using a CSIR-developed wax-based binder system at a fixed solids loading of 60 vol.%. The distribution slope parameter and the rheological flow index behaviour were used to predict the flowability of the feedstocks. The effects of the particle size on MIM products were established. The results are discussed in terms of the subsequent microstructural and mechanical properties of MIM 17-4 PH stainless steel against the established MPIF Standard 35. IntroductionMetal injection moulding (MIM) is a near-netshape manufacturing process established as an alternative to produce complex small-tomedium shaped components that were previously fabricated by conventional methods at higher costs (Attia and Alcock, 2011; Todd and Sidambe, 2013).Although recent advances in micromanufacturing (mainly machining and electrodeposition-based) have enabled the fabrication of complex micro-size geometries directly into miniaturized parts, these processes are generally neither routine nor easily accessible at present (Attia and Alcock, 2011).Typically, the MIM process consists of four steps: mixing, injection moulding, debinding and sintering. Mixing involves blending of the desired metal powder composition with carefully selected multicomponent organic binders at the right proportion. This mixture, which is called feedstock, is then injected into a mould of a required shape to form a ‘green part’. Debinding is the removal of the binders by chemical, thermal, or catalytic means while maintaining the shape of the part. Finally, the debound part is sintered to a full or near-full density part (Sotomayor, Varez and Levenfeld, 2010). The MIM process is essentially a combination of plastic injection moulding with conventional powder metallurgy technologies."

Jan 1, 2016

By J. Bal, V. D. Dao, W. Li

"SynopsisThis study proposes a methodology for evaluating the risk of coal bumps in multiple-seam longwall mining. Both the stress field and the total energy release (TER) during retreat were evaluated in the specified case involving multiple-seam mining using the LaModel program. The results of numerical simulations indicated that both the peak vertical stresses on the panel edges and the peak TERs in the outby longwalls increased significantly as the horizontal offsets were reduced from 60 m to zero. With the comprehensive consideration of the stress field and TERs, a conservative offset of 60 m was ultimately adopted when developing the gateroads of the lower panel in the field. The field measurements indicated that coal bumps were avoided completely by employing the proposed design, and the maximum roof-to-floor and rib-to-rib convergences of the tailgate during retreat were only 360 mm and 576 mm, respectively.IntroductionCoal bumps – sudden, violent bursts of coal – pose a serious threat to the safe excavation of coal. Their occurrence depends on the properties of the surrounding rocks, stress field, and dynamic disturbance. The complexity of the mechanism of coal bumps is further enhanced in multiple-seam mining due to seam interaction. Multiple-seam mining is most frequently found in the coalfields in eastern China, such as Xuzhou, Xinwen, Zaozhuang, and Huainan. In the past, due to issues of availability, economics, and ignorance of the potential risk in multipleseam mining, coal seams in such conditions were mined without proper planning to account for seam interaction. Fortunately, studies published over the past three decades have raised awareness of the problems associated with multiple-seam mining, and indicated that the ground control issues induced by multiple-seam mining can be avoided and/or minimized with proper planning.A number of technical studies pertaining to the design of multiple-seam mines have been published. These studies can be divided into two groups based on their methodologies of design: empirical (Chekan and Listak, 1993; Haycocks and Zhou, 1990, Matetic et al.; 1987a, 1987b) and numerical approaches (Li et al., 2000; Maleki, 2007; Mark, 2007; Peng, 2007; Zipf, 2005). The majority of the extant studies on the interaction mechanisms in multiple-seam mining have focused on the load transfer during operation, resulting in the proposal of the pressure bulb theory (Forrest et al., 1987; Haycocks and Karmis, 1983; Peng, 2008; Peng and Chandra, 1980) and pressure arch theory (Holland, 1973; Oram and Ponder, 1997) to guide multiple-seam mine design. However, neither, of these theories can be used to evaluate the potential for coal bumps."

Jan 1, 2015

By G. Sánchez, S. Seiler, B. Klein, T. Cebeci, P. Bradshaw

The Decar Nickel District is a greenfield discovery by FPX Nickel Corp., of nickel mineralisation located in central British Columbia (BC), Canada. The Baptiste deposit is part of the Decar Nickel District and is a unique deposit containing a nickel-iron alloy mineral called awaruite, with over 2-billion tonnes of inferred resource grading 0.12% Davis Tube Recoverable (DTR) nickel. This deposit represents a significant nickel resource. Awaruite is a high density and ferromagnetic mineral, which could be recovered, along with magnetite that is also present in the samples, using magnetic separation. However, there is still a lack of understanding of the properties of the awaruite and its metallurgical response. This information is imperative for the set-up of the variables involved in its concentration. The aim of this paper is to show and discuss the effect of magnetic field strength for the recovery of nickel from Baptiste deposit samples. Magnetic separation at bench and pilot scale with different magnetic field strengths is evaluated as a concentration method for awaruite. Mineralogical information is provided to support the results and also to briefly assess the variability of DTR nickel within the deposit. The Baptiste deposit is unique and will benefit from a sound scientific understanding of the process solution as well as other ongoing work. If successful, the outcome will lead to the development of a mine. With greater than 2-billion tonnes of inferred resource, the mine would represent a significant new source of nickel globally. Keywords: Nickel ore processing, magnetic separation , awaruite, magnetite

Jan 1, 2020

By A. Melkumyan, M. Balamurali, J. Zigman

Understanding the contribution of geophysical variables is vital for identifying ore indicator regions. Both magnetometry and gamma-rays are used to identify the geophysical signatures of the rocks. Density is another key variable for tonnage estimation in mining, and needs to be re-estimated in areas of change when a boundary update has been conducted. Modelling these geophysical variables in 3D will enable investigation of the properties of the rocks and improve our understanding of the ore. The Gaussian Process (GP) was previously used to generate 3D spatial models for grade estimation using geochemical assays. This study investigates the influence of the following two factors on the GP-based autonomously generated 3D geophysical models: the resolution of the input data, and the number of nearest samples used in the training process. A case study conducted on a typical Hammersley Ranges iron ore deposit using geophysical logs, including density, collected from the exploration holes, is examined in this paper.

Sep 1, 2021