Search Documents

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By M. A. Trevits, A. Ozmet, A. C. Smith, J. B. Walsh, T. P. Mucho

Improvements in remote fire fighting technology are needed to reduce miner exposure to the dangers of fires and possibly save the lives of those who may become trapped. The National Institute for Occupational Safety and Health, in cooperation with U.S. Foam Technologies, Inc1., conducted a series of experiments at the NIOSH Lake Lynn Experimental Mine to study the stability, transport, control and fire extinguishing effectiveness of nitrogen-enhanced foam technology. This paper presents a description of the mine test configurations and experimental results

By C. R. Carpenter

A dynamic gas-mixing system assembled by the Bureau of Mines for the generation of precise gas mixtures from sources of concentrated or pure gases and diluent gases is described. A set of electronic mass flow controllers with maximum flows ranging from 10 to 5,000 ml/min, a so-called Pure Air Generator, and gases in cylinders are used to generate differing gas concentrations. The repeatability of the delivery rate of a flow controller, measured on different days, has a precision of 0.3 pct of the setting. This dynamic gas-mixing system reduces the cylinder inventory and the demurrage charges for special gas mixtures. Gas mixtures that cannot be shipped commercially, such as flammable mixtures of methane in air, can be conveniently prepared by this system. The maximum dilution ratio is 2.5 x 104. Thus, gas mixtures can be made over a wide range of concentrations, from the percent region (by dilution of a pure single-component gas) to fractional parts per million (by dilution of a premixed standard, e.g., a 1,000-ppm mixture). This system is especially useful in determining the response of gas detection devices over the entire range of their measurement. Because the controllers are voltage controlled they lend themselves easily to automated control using computer-based systems.

Jan 1, 1983

By W. T. Benson

Peacetime production of mercury in the United States is controlled by world mercury prices, with significant lags to be expected between price increases or decreases and resultant increased or decreased production. Twenty-four mercury-bearing mines and prospects in widely separated districts in western and central Nevada and one property on the Nevada-Oregon border were examined and sampled. The purpose of the project was to determine if some of the properties warranted more extensive exploration work to obtain information on possible reserves of commercial-and sub-commercial-grade ores. The investigation of mercury deposits in Nevada was sufficiently widespread and indicated several areas of interest in the State that merit further exploration work.

Jan 1, 1956

By Ann G. Kim

The U.S. Bureau of Mines mine fIre diagnostic methodology to locate and monitor fIres in abandoned mines and waste banks is based on the controlled sampling of the mine atmosphere to determine changes in the concentration of hydrocarbons desorbed from heated coal. To provide background data for this methodology, a laboratory study was conducted in which samples of coal and coal waste were heated under controlled conditions. Gas samples from the combustion furnace were analyzed for standard gases CO2 and CO and for the C1 to Cs hydrocarbons. In all tests, the concentration of desorbed hydrocarbons increased during heating and decreased during cooling. A dimensionless hydrocarbon ratio, Rl, was developed as the signature for heated coal. For bituminous coals, the value of Rl increases during heating of coal samples and decreases during cooling of the same samples. Generally, Rl values of 100 or more indicate coal sample temperatures of at least 100° C. The emission of higher molecular weight hydrocarbons from anthracite samples was very low, resulting in relatively low Rl values at all temperatures. Data from fIeld projects confIrmed these results.

Jan 1, 1991

By Oliver C. Ralston, Dorsey A. Lyon

Volatilization in retorts has been, until recently, the only commercial process of producing spelter, hence the zinc mine operators have had to meet the terms of the zinc smelters in regard to the following requirements: (1) Minimum percentage of zinc the ore must contain; (2) the chemical combination of the zinc in the ore; (3) the proportion present of those elements that interfere with the suceessful recovery of the zinc when the ore is retorted. In consequence of these requirements, only a comparatively small proportion of the zinc ores mined can be shipped directly to the smelters.

Jan 1, 1919

By Charles L. Kimbell

The year 1980 on the whole was not a good year for the world's mineral industry. The general upturn of activities in 1979 after a rather poor 1978 showing was not maintained with a number of key measurement standards showing downturns. Most notably, the world's steel and petroleum industries recorded significant reductions in output, the former in response to markedly lower demand levels and the latter partly in response to lower industrial consumption owing to general economic conditions and partly owing to successes in campaigns for the reduction of energy use in general and petroleum product use in particular among major importing nations that were feeling the trade balance pinch of ever-higher oil prices. During 1980, a number of political events-some international in scope, some confined to single nations-had significant influence upon world mineral industry activities and mineral commodity supplies, and other political happenings had the potential to significantly affect the industry in future times.

Jan 1, 1982

Combine the MSHA and OSHA versions of the HazCom Helper into one easy-to-use software tool.

Jan 6, 2007

By Robert W. Waytulonis

This publication contains 1,000 citations of technical and semi-technical literature treating diesel-powered equipment usage underground both generally and specifically. These citations were gathered by U.S. Bureau of Mines personnel over the period of 1978-1983. The citations concern diesel engines as powerplants for underground mining use; their design, emission characteristics and control, maintenance, usage; and health and safety aspects. All citations have been abstracted and arranged 1n a subject classification system with extensive cross-referencing.

Jan 1, 1983

The accompanying supply/demand flow diagrams and 10-year tables for mineral and fuel commodities present essential data required by government, industry, and others to formulate policies and programs that can help assure an adequate and continuing supply of mineral raw materials. The 10-year data base terminates with 1973 figures because adequate world information was not available beyond that date. Moreover, 1974 was an anomalous year with respect to prices, supply, and demand for many commodities. The selected mineral supply/demand tables and flow diagrams comprise but one "output" from the massive body of "information and data collected and com-piled by the Bureau of Mines on a continuing basis covering mineral production consumption, prices, shipments, imports, exports, and stocks, as well as industry activities in all States and abroad.

Jan 1, 1975

By N. T. Lowe

This Bureau of Mines publication presents salient deposit information in abstract form on 119 principal mineral deposits in the State of Nevada. Commodity coverage addresses 17 critical and strategic commodities that appear to have commercial production potential in the State. The core of the deposits described is taken from those properties evaluated d under the Bureau of Mines Minerals Availability Program (MAP); additional deposits are included to provide a more complete coverage. Institutional and infrastructural factors affecting mineral development are also discussed.

Jan 1, 1985

By D. R. Tesarik

As part of its research program to investigate ways of improving resource recovery and reducing subsidence, researchers from the U.S. Bureau of Mines placed instruments in the B-North ore body of the Cannon Mine, Wenatchee, WA, to monitor cemented backfill and rock deformation during mining. The vibrating-wire gauges proved to be reliable and versatile, and approximately half of the instruments are providing data after 2 years of use. A two-dimensional, finite-element model was used to analyze the Cannon Mine's multilevel bench cut-and-fill mining method and predict rock and backfill displacements. The model accurately predicted rock displacements, but the predicted and measured displacements in cemented backfill had a correlation coefficient near zero, indicating that the model should only be used to predict rock displacements and not backfill displacements. A finite-difference model was also used to evaluate the stability of a cemented backfill pillar. Results can be used to conservatively predict backfill stresses, but on-site observation of pillar failures coupled with in situ measurements are needed to make more accurate predictions. An ongoing evaluation of the mining system has indicated that filling the primary stopes tight to the back with cemented backfill allowed these pillars to carry overburden loads soon after the cemented backfill was placed.

Jan 1, 2010

By G. W. Josephson

WHILE methods of utilizing blast-furnace slag have been developing, a great deal of literature on the subject has accumulated, but no comprehensive summary of information that would be helpful to engineers, contractors, architects, chemists, and others in under-standing and more successfully using this byproduct of the iron and steel industry has been published in the English language. The National Slag Association recognized the need for such a publication, and the Problems Committee of the Association under-took in 1943 to accumulate the necessary material. Over a period of several years this committee compiled pertinent information in manuscript form, and in 1948 the Bureau of Mines and the National Slag Association made an agreement whereby the Bureau was to prepare the data for publication as a cooperative bulletin of the Bureau of Mines and the National Slag Association.

Jan 1, 1949

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

To develop a conceptual design for an automated longwall mining system, one should know what has been done, what is being done today and what is being planned for tomorrow. The bibliography referenced and discussed in this report provides a good source for that knowledge. To scientifically determine where attention should be focused to up-grade a system, the system must be quantized as far as possible. The Mechanization Profile of Appendix A-I is discussed in this report and has been used to analyze and determine the degree of mechanization currently in use and/or described in the literature for all three major elements of the long-wall system, namely, Winning, Roof Support and Haulage. The charted profiles make it self-evident where attention and design effort is needed to remove human operators from the face of the mine.

Jan 1, 1975

By H. C. Miller

Several agencies of the Federal Government are engaged in research and fact finding relative to petroleum and natural gas, and others are concerned with carrying out the provisions of specific laws that affect these natural resources in their broad aspects. The Bureau of Mines, however, is the only Federal agency designated by law to engage in research in oil and natures gas production, chemistry, refining, and

Jan 1, 1941

By Charles V. Jude

This U.S. Bureau of Mines report presents a review and evaluation of existing and new backfilling materials and methods for their applicability to the problem of gate road stress reduction in deep retreat longwall coal mines. Candidate backfill materials include pulverized coal combustion fly ash, flue gas desulfurization, and fluidized bed combustion by-products from coal-fired electric power generation plants. Properties of both backfill and its component materials are presented, with particular emphasis on the unconfined compressive strength and elastic modulus of backfill mixtures. Hydraulic mix designs discussed in this report include high-water content slurry and low-water content paste fills. Three gate road stress-transfer-modification concepts are proposed to reduce abutment stresses in gate road systems. The first concept, packwalling, involves packwall construction behind the headgate shield inby the face and adjacent to the headgate pillars. The second concept, gob-filling, involves infilling a strip of gob inset from and parallel to the headgate using paste injection methods patterned after a technology recently developed in Europe. In the third concept, entry-filling, slurry fill methods are used to fill abandoned gate roads and crosscut entries inby the face.

Jan 1, 1995

By John R. Bartels

Jan 1, 2009

By Wilbert J. Huff

The work of the Explosives Division, Bureau of Mines, United States Department of the Interior, for the fiscal year ended June 30, 1939, is described in the following pages. This paper is the fourth of a series of annual reports covering the activities of the division since July 1, 1936. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders to whom specific credit is indicated.

Jan 1, 1940

"These tentative coal mine inspection standards have been prepared as a guide for the Federal inspection of coal mines of the United States. Much time and thought have been spent by various members of the Safety Division in the preparation of thses standards, and it is believed that compliance with them eventually will be possible in most mines. In many instances objections will be raised to them owing to long-established mining customs and practices that are inherently of dubious safety and to a natural inclination to oppose change. In other instances there will be valid objections due to conditions not foreseen at the time these standards were prepared. Or there may be substandard conditions and practices due to original mine layouts that it is not practicable to change during the lifetime of the mine; in such instances it is likely that some effective measures are or can be taken toward lessening hazards.With the rapid change in mining methods some of the standards may become inapplicable and it may be advisable to revise them to meet the new conditions. Therefore, questions regarding these standards and suggestions regarding new standards should be brought to the attention of the supervising engineer of the Coal Mine Inspection Division so that modifications of and additions to these standards may be made from time to time.In many respects these standards exceed the provisions of the various State mining laws, and some may conflict with the laws of some States. In cases of conflict, the intent is not to advocate noncompliance with State laws but to suggest that it may be desirable for the State to reconsider such laws or safety orders.Although an effort has been made to word these standards so that they may be readily understood, nevertheless, a reasonable interpretation should be placed upon them. In fact, in numerous instances the words reasonable"", ""suitable"", and ""properly"" are used in recognition of the fact that reason- and sound judgment enter into the carrying out of the safety endeavor.The policy of the Bureau on some vitally important safety matters in mines is set forth in its published Safety Decisions. These decisions have been consulted and used in the preparation of these standards. These decisions also are now being reexamined by its Mine Safety Board."

Feb 1, 1942