Search Documents

By J. Burlin Johnson

In small-scale blasting experiments conducted in the Bureau of Mines laboratory, small charges were used to produce craters in blocks of concrete mortar. The results are compared with larger scale experiments of other research workers, and the comparison demonstrates the similarity of the results obtained and indicates that small-scale blasting should be a useful tool for predicting large-scale blasting effects. INTRODUCTION The purpose at this investigation was to conduct blasting experiments in mortar in the laboratory and then, by comparing the results with those from larger scale field blasts in rock to determine to what extent, if any, the laboratory results resemble those in the field. The work described herein was the initial phase of a project aimed at evaluating small-scale blasting as a tool for use in improving blasting techniques. It is evident from the stand-point of control and cost that small-scale blasting would be valuable in the study of rock fragmentation by blasting in mines and quarries, if the extrapolation is valid.

Jan 1, 1962

By James R. McVey

A new method for measuring deformations of rock surfaces in underground excavations has been suggested by Dr. James Powell of Brookhaven National Laboratories (BNL) and subsequently developed and successfully demonstrated in a mining environment by the Federal Bureau of Mines, Spokane Mining Research Center (SMRC) and Brookhaven National Laboratories. The system uses 35-mm photography of targets strategically located on surfaces of interest, such as across the roof and on the sides of a mine drift or tunnel. The optimum tar-get, as determined in this investigation, consists of a white ?X? made with 1/8-inch-wide reflective tape on a black 6-inch square. Photographs, taken in pairs from two separated camera positions and at regular time intervals, were analyzed at the Bureau by hand and at Brookhaven National Laboratories using techniques and equipment similar to those used in cloud chamber film analysis. Test results show that deformation-measurement accuracies of better than ±0.020 inch in a drift that is 20 feet wide can be expected. This degree of accuracy, plus providing displacement data in the X, Y, and Z directions (rather than the one direction formerly possible), makes this a noteworthy and useful tool for industry as well as for mining research.

Jan 1, 1974

By J. H. Soulé

The Copper King copper-gold-silver deposit was discovered about 1880. Various individuals and companies have been interested in the deposit and considerable work has been done, although production, if any, has been small. The deposit is located in the western part of Laramie County, Wyo., and is favorably situated with respect to rail and truck transportation and high-tension power facilities. Mild summers and cold winters characterize the climate. Precipitation averages between 16 and 17 inches annually, with considerable snowfall in the winter. Permanent streams are small and most available water in being stored for use by Cheyenne, Wyo. Range grasses comprise the bulk of the vegetation, with small trees and shrubs common in the most rugged areas.

Jan 1, 1955

By David C. Byrne

PURPOSE: Evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. RESEARCH SUMMARY: The results of previous NIOSH research show that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and gender. Using hearing thresholds at 4,000 Hz as an indicator, coal miners experience hearing loss 2.5 to 3 times greater than would be expected for persons not exposed to occupational noise. At age 50, 90% of coal miners and 49% of metal/nonmetal miners were found to have a hearing impairment. In comparison, only 9% of a nonoccupationally exposed control group had a hearing impairment at age 50. There are numerous barriers to the prevention of hearing loss among miners. In an effort to overcome some of these obstacles, this work was initiated to evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. Experiments will involve analysis of this new technology under both laboratory and field conditions. Laboratory components will consist of controlled studies using an anthropometrically correct test fixture as well as human subjects to evaluate the adequacy/effectiveness of various hearing protective devices. Electroacoustical performance testing of new noise monitors will also be conducted in a laboratory setting. Subsequent field studies will determine the actual usefulness and practicality of the personal protective/monitoring equipment as used in different mining situations. It is anticipated that increased on-the-spot awareness of hazardous noise levels and the availability of better-suited hearing protectors will provide a degree of protection beyond what is currently attained in different mining environments. Therefore, the intent of this project is to identify and adapt new acoustical technologies and products that have a direct application to individual mine workers. With increased knowledge of these technological advances, a greater demand for similar devices will likely occur, which, in turn, will lead to a better understanding and awareness of hearing loss prevention methods throughout the mining community. The ultimate goal is for widespread integration of useful hearing loss prevention products and devices into the daily routines of miners

Jan 2, 2000

By Robert C. Steckley

The Bureau of Mines performed a fragmentation experiment in cooperation with Duval Corporation in a porphyry copper-molybdenum deposit near the Sierrita pit south of Tucson, Ariz. This experiment evaluated the fragmentation created in a 10-hole test blast having blasthole spacings of 25, 20, and 15 feet. The 10 blastholes were 9 inches in diameter and contained a total of 17,400 pounds of aluminized slurry blasting agent in 50-foot columns with 60 feet of stemming. Diamond drill core examination was the primary method used to determine the condition of the rock before and after blasting. These core examinations included study of length recovery, rock quality designation (RQD), weight recovery, and size distribution. Topographic surveys were used to measure the rock swell produced by the blast and a fragment size distribution was obtained for the broken material on the surface. Fragmentation to depths of 110 feet was excellent from the 15-to 20-foot blasthole spacing patterns. Good breakage was also produced by the 25-foot pattern although the effects of the blast were not so obvious. In situ leaching tests were not conducted. However, based only on size consideration, all three blasting patterns produced adequate breakage for successful leaching.

Jan 1, 1975

Table 1.-Salient aluminum statistics (Thousand short tons and thousand dollars) [ ]

Jan 1, 1967

By Ivan F. Avery

OUTPUT of carbon black in 1959 increased in all producing States except New Mexico. The national increase was 20 percent. Domestic sales and exports increased 22 percent and 16 percent, respectively, resulting in a 21 percent gain in sales. Sales to the rubber industry, which purchased 95 percent of the domestic output of carbon black, increased 23 percent. Sales to all other major consumers also increased. Stocks decreased 82 million pounds during the year. [ ]

Jan 1, 1960

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in the country and regional reports that comprise the five other sections of 1991 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, appreciation is expressed to the multitude of persons employed by these agencies.

Jan 1, 1993

By George S. Rice, Li C. Ilsley.

A remarkable explosion of fire-damp caused by a discharge of lightning at the new shaft at the Sitalpur coal mine, has been reported by the Chief Inspector of Mines of India, who gave the following details: "The explosion occurred during a thunderstorm, and the evidence showed that a flash of lightning had, to all .appaarances, passed down the shaft causing disruptive disohalges at certain points between the guides and the winding rope, Tending the latter at two places situated respectively 228 feet and 278 feet frem the surface, The distance between the winding rope and the side of the shaft was 6 feet 4 inohes, indicating a spark gap;of this width, and an intensity of discharge which could not fail to ignite the explosive mixture of gas and air known to be present in the shaft."

Feb 1, 1920

By Guy E. Dent, Robert S. Sandford, W. T. Millar, Hugo E. Kuehn

"INTRODUCTION AND SUMMARYDuring the latter part of 1943 a magnetometric survey was conducted by the Geophysical Division of the Bureau of Mines at the mine, Putnam County, N. Y., in an endeavor to locate a segment of the body that reports state was cut off by a fault. The Mahepac mine was abandoned about 1895 after producing nearly 1,000,000 tons of high-grade magetite iron ore. The results of the investigation indicate the termination of the ore body by ""pinching"" or a displacement of such magnitude as to place any extension at a considerable distance the original ore body. This report describes the work done on the project and presents the data obtained. ACKNOWLEDGMENTSThe Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. The Mahopac mine was visited by W.T. Millar, an engineer of the Bureau of Mines, on June 5, 1943, accompanied by Dr. William Agar of the Federal Survey, and again on July 29, 1943, accompanied by Dr. A. F. Buddington and H.F. Hawkes, both of the Geological Survey.The mineral investigation was under the general supervision of Paul M. Tyler, formerly regional engineer, Eastern Region; J. D. Bardill, formerly district engineer; and Dr. F.W. Lee, formerly chief. Division, Geophysical Exploration. The work was done under the immediate supervision of W. T. Millar, project engineer. The Geophysical Survey was made by Hugo Kuehn and Guy E. Dent."

Sep 1, 1948

By D. S. Kimmel

The Bureau of Mines sponsored development of a system to remotely energize and de-energize the trolley wire in a section in response to demands from vehicles as they enter and leave the controlled section. The system developed utilizes a detector/actuator that controls a dc contactor at the outby end, and a 3 kHz oscillator at the inby end. A prototype system has been built and installed at the Bureau's trolley test site at Bruceton, Pennsylvania which has demonstrated the ability to also provide load discrimination for faults of 300 amperes or more. The system could readily be modified by locating the oscillator on the vehicle to provide automatic de-energizing of the trolley wire when the vehicle's pole is removed or the vehicle leaves the section.

Jan 1, 1978

By R. Craig Smith

The Bureau of Mines conducted a study of production costs for the secondary lead industry and determined costs for present, pending, and proposed environmental legislation. Operating costs for smelters by capacity groups range from 16.8 to 19.6 ¢!lb of refined lead. Present regulatory compliance costs for these groups range from 2.2 to 2.4 ¢!lb. Pending compliance costs could add 3.5 ¢!lb of refined lead, and proposed regulations could add another 1.3 ¢!lb. The individual capital costs necessary to comply with pending environmental regulations are estimated to be $1.8 million for small smelters and $10.4 million for large smelters. Proposed regulations could require additional expenditures from $1.9 million for small smelters to $4.9 million for large smelters. These cost estimates, based on average 1985 dollars, indicate that pending and proposed legislation could add significantly to capital and operating costs of the secondary lead industry. These regulatory compliance costs may result in a loss of up to 40 pet of secondary lead production capacity.

Jan 1, 1987

By Carl Rampacek

Recent research by the Bureau of Mines has demonstrated that the segregation process has merit for treating oxidized and mixed oxide-sulfide copper ores. The process comprises heating the crushed ore with salt and coke or other carbonaceous materials at about 700° C. to produce fine flake copper, which then is recovered by conventional copper-flotation methods. Bench-scale laboratory tests of a number of oxidized and mixed copper ores assaying 0.78 to 5 percent Cu gave copper recoveries of 73 to 96 percent. The flotation concentrates assayed 21 to 76 percent Cu, depending on the ore being treated.

Jan 1, 1959

By Larry G. Stolarczyk

This report deals with information regarding a new Medium Frequency (MF) Wireless Communication System for underground mines. This new telecommunication system works on low loss electromagnetic wave propagation modes which allow it to provide quality radio communications almost anywhere in a mine. Tests show the MF system can provide improved safety and managerial control, increased productivity, better organizational team-work and reduced maintenance cost; furthermore, MF's unique design allows for easy installation at a minimum cost. This paper covers the following: 1) MF design plan, 2) Overview of mine radio communications systems, 3) Preparations needed for designing an MF system, 4) MF equipment, 5) MF installation, 6) MF design considerations, 7) MF design specifica¬tions, and 8) Recommendations dealing with MF system. Experiments in four mines are illustrated to demonstrate the success and via¬bility of the MF system. The mines range from small (500 tons/day) to large (67,000 tons/day) capacity and represent several different mining methods. The MF Wireless Communication System represents an advancement in mining communication and the groundwork for other advanced mine systems.

Jan 9, 1984

By Ivan F. Avery

DOMEST1C production of carbon black in 1963, remained at about the same level as in 1962. Carbon black produced by the furnace process increased 2 percent to 1,880 million pounds in 1963 and accounted for 91 percent of the total output. Channel black production continued to decline and was 14 percent less than a year ago. Shipments during 1963 totaled 2,098 million pounds, a 1 percent increase for the year. An increase of 88 million pounds in domestic sales was partially offset by a decrease of 72 million pounds in carbon black exports. Total value of carbon black production in 1963 was $148 million. The average value per pound was 7.18 cents or 0.12 cent per pound more than in 1962.

Jan 1, 1964

By John H. Hild

The topography of the Jamestown fluorspar area is rough and ranges from 6,400 to 8,000 feet in altitude. Some fluorspar was mined as early as 1870, but mining really did not begin in earnest until 1940, and up to July 1947 it is estimated that 272,500 tons of fluorite was mined and milled. In 1947 the General Chemical Co. was mining fluorite and milling it in a 200-ton-a-day mill at Valmont, 7 miles east of Boulder, and the Ozark-Mahoning Co. was milling ore in a 100-ton-a-day mill at Jamestown, using ore mined, by H. M. Williamson & Son. These fluorite deposits comprise veins in a granite country rock. The Bureau of Mines drilled eight holes, aggregating 2,579.1 feet, on the Blue Jay vein; four holes, aggregating 1,434 feet, on the Chancellor; and one 350-foot hole on the Nations Treasure. Fluorite of a minable grade and width was found in 10 of the holes drilled. In this report the location and accessibility, physical, features and climate are described and a brief history of the district is given. The deposits and character of the ore and sampling and analyses are described, mine workings are outlined, and work performed by the Bureau of Mines is summarized. Diamond drill logs are shown in appendix I, and 'Sample analyses are tabulated in appendix II.

Jan 1, 1949

By T. T. Campbell

A survey of the literature eras made covering the use of aqueous non-aqueous, and fused-welt systems for the electrowinning or electroplating of molybdenum metal. The survey was prepared in order to provide background for further investigations directed toward the electrodeposition of pure molybdenum metal from either aqueous or nonaqueous mediums. While a thorough effort was made to cover all available references, a critical review was not attempted nor does this survey pretend to be exhaustive in nature.

Jan 1, 1955

Mainland China To Pay Japanese Company On Contract Claim. - Mitsubishi will receive $39 million from Red China, half of what was asked, for China's having, curtailed work on a 5369 million steel rolling mill at Baoshan near Shanghai. Copper Found in Chile. - Utah International Inc., in conjunction with Getty Oil Co., has discovered a cooper deposit in northern Chile. Early drilling reveals an enriched zone grading 1.2% to 2 3% copper. Chile already has tie world's largest Cu reserve base. Soviets To Aid Laotian Tin Industry. - The U.S.S.R. has agreed to help strengthen the tin industry in Laos, a client state. In the past, Laos has only produced small amounts of tin concentrate, 500 tons to 1,000 tons per year presumably shipped to smelters in Singapore or Penang, Malaysia. Under the agreement made in June, the Soviets are to supply equipment to increase the out put of tin from the Phontieu, Neng, and Nongsen mines and help Laos with the construction of a tin smelter. The U.S.S.R. itself is a net importer of tin, although a substantial producer of the metal.

Jan 1, 1981

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Ti and Zn-1.0 wt pct Cu-Ti alloys containing up to 0.36 wt pct Ti. Finish rolling was at varied temperatures to total reductions as high as 92 pct. Alloy properties are very sensitive to various combinations of composition, rolling temperature, and reduction. Properly rolled Zn-1.0 Cu-Ti alloys are superior in strength to Zn-Ti alloys. Conditions are described that lead to best tensile properties. Creep resistance for Zn-Ti alloys decreases with increased rolling temperature when finish rolled to 92-pct total reduction: but not when finish rolled to 33- or 67-pct reduction. Creep resistance for 7n-1.0 Cu-Ti alloys improves with increased rolling temperature to about 480° F. Heavily cold-rolled Zn-1.0 Cu-Ti alloys have fine grain sizes and poor hardness, tensile, and creep properties, but high ductility. Thermal expansivity is markedly affected by the copper addition. Data show the anisotropy of tensile, creep, and thermal expansivity properties. Large idiomorphic crystallites of TiZn15 appear in both Zn-Ti and Zn-Cu-Ti alloys when more than about 0.2 pct Ti is present. A new Zn-Cu-Ti intermediate phase was also identified. Empirical equations are presented relating creep rates with major process variables.

Jan 1, 1971

By William J. Campbell

The Federal Bureau of Mines provided five test materials--amosite, short-and long-fiber chrysotile, crocidolite, and nonfibrous tremolite--to the National Institute of Environmental Health Sciences (NIEHS) for studies on the biological effects of orally ingested asbestos-related materials. An inter-agency agreement between the Bureau and NIEHS made possible this program to characterize these test materials. The Bureau in turn received support through contracts with the Ontario Research Foundation for the milling of amosite and crocidolite, and with the University of Maryland for microscopic measurements. The five test materials, which were supplied in quantities of 960 to 1,200 pounds each, were characterized by chemical-instrumental analysis for elemental composition, surface area, density, X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, mineralogy, and particle size analyses. Particle size distributions were emphasized because of the current theories relating adverse biological effects to length-width characteristics of durable elongated particles.

Jan 1, 1980