Search Documents

By G. Esterhuizen, C. Karacan

Methane can be a significant hazard in coal mine longwalling operations and extensive methane mitigation techniques are employed by coal mine operators. Reservoir modeling techniques are used to better understand the liberation and migration of methane from the surrounding rocks towards the mine ventilation system. The caved rock behind the advancing longwall face, known as the gob, can contain high void ratios, providing high permeability flow paths to the methane. The gob is progressively compacted by the weight of the overburden, resulting in a reduction in the void ratio and associated permeability. Estimating the permeability distribution within the gob poses challenges due to its complexity. The authors have developed a new methodology to determine both horizontal and vertical variations in the permeability of the gob. Variations of the permeability in the vertical direction are based on a model of caving and block rotation, which considers the effect of block dimensions and fall height on the void ratio. Gob compaction by the overburden and associated permeability changes are determined from a three-dimensional geo-mechanical model which simulates the gob as a strain hardening granular material. The resulting three-dimensional permeability distribution in the gob is then transferred to a reservoir model. The paper demonstrates the application of the method and shows that reasonable results are obtained when compared to empirical experience and measurements.

By David C. Oyler

The U.S. Bureau of Mines and the United States Steel Corporation evaluated the progress of methane drainage at the Oak Grove, AL, degasification pattern. Coalbed pressures were monitored between December 1981 and November 1985. Formation pressures, in the lower bench of the Mary Lee Coalbed, were reduced from 400 lbf/in2(ga) in 1977 to 50 lbf/in2(ga) in November 1985. Gas contents of coal cores obtained from monitor wells were compared with coalbed gas contents measured in 1976. Data indicated a 48- to 56-pct reduction within the pattern and a 29-pct reduction at a point 500 ft outside the pattern. The effect of the advance of a section of the Oak Grove Mine on changes in gas and water production rates in the pattern was evaluated. Gas production increases were noted in 12 wells; water production decreases were noted in 6. The times of initial influence indicate the presence of a zone of high permeability within the pattern. This zone correlates well in orientation and location with a fracture zone mined through at the mine. The existence of such fracture zones could have a significant effect on productivity of individual coalbed methane wells.

Jan 1, 1989

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 29,020 acres of the 43,165-acre Terry Badlands Wilderness Study Area (MT-024-684) in order to evaluate its mineral resources. Within this report, these 29,020 acres are referred to as the study area. Located in Custer and Prairie Counties, MT, the study area is about 2 miles northwest of Terry. The study area is underlain by essentially flat-lying units of the Fort Union Formation of Paleocene age with some Quaternary alluvial deposits in stream valleys. No mines or prospects were found in the study area. Bentonitic clays and lignite coal units were examined and sampled; however, no clay resources or coal reserves were identified. Estimates of coal resources will be reported by the U.S. Geological Survey in a joint U.S. Geological Survey-U.S. Bureau of Mines publication. Gravel along the Yellowstone River, a source of agate for private collectors, could also be used as sand and gravel aggregate although material on the south bank of the river is closer to population centers and road systems. Clinker found in the study area could be a source of road metal, but is not well situated in relationship to areas of use. No geothermal resources have been identified although water suitable for direct heat applications may underlie the study area. All the area is leased for oil and gas exploration.

Jan 1, 1985

By Robert Blickensderfer

Equipment and procedure for the continuous roll bonding of metal strips are described. The reels, mill rolls, and furnace were located within a vacuum chamber capable of operation at a residual gas pressure of 1 x 10-4 to 1 x 10-5 torr. Several metals were successfully clad at rolling temperatures of 930° to 1,050° C in lengths up to 120 ft. The bimetals that were clad included stainless steel to carbon steel, molybdenum and nickel to stainless steel and carbon steel, and titanium to carbon steel. Bend tests of bond integrity are described, and microstructures of the interfaces are presented. The amounts of brittle intermetallic phases formed at the interface are minimized by this cladding method.

Jan 1, 1980

By John L. Ellenberger

The Bureau of Mines investigated the occurrence of slickensides in mine roof in the Pittsburgh coalbed in a portion of the Valley Camp No.3 mine in southwestern Pennsylvania to improve the potential for prediction of slicken-sided zones and determine the orientations of the most prominent slickensided planes. Two distinct types of slickensides were identified; those which were associated with clay veins observed in the coalbed (genetic), and those which were unrelated to any visible structure (nongenetic). The study draws three conclusions: (1) Nongenetic slickensides are not the result of tectonic forces, (2) both genetic and nongenetic slickensides tend to dip at an angle of 30°, and (3) genetic slickensides tend to be alined parallel to the trend of the clay vein and usually dip toward the center of the clay vein. A schematic roof bolting plan is presented that may provide improved roof support where slickensides are present. Roof stability could be improved by supplemental bolting in the direction normal to the plane of slickensides.

Jan 1, 1979

By E. J. Matson

"SUMMARYThe Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Projects were set up on only the most promising properties. A preliminary examination of the Rio Grande property was made by Bureau of Mines engineers in July 1942 and the property was examined again in July 1943.The Geophysical Branch of the Bureau undertook a Geophysical survey of the area in November 1943 and was intermittently active in the district until June 1946. The major portion of their work was done from June 191 to November 1945. Favorable areas for exploration were recommended by the Geophysical Branch of the Geological Survey, 3/ and all holes were drilled in them.Two projects were set up by the mining branch in an endeavor to find ore bodies on the strength of the geophysical information."

Sep 1, 1947

A significant amount of information regarding the crushed stone and sand and gravel industries in each State is available from State agencies and State trade associations. These organizations continuously monitor the State mineral industries and are therefore an important source of detailed information at the local level. This third edition of the directory was prepared to provide a listing of government agencies and trade associations that can assist the users interested in obtaining detailed listings of crushed stone and sand and gravel producers, in addition to the information published by the U.S. Bureau of Mines.

Jan 1, 1994

By C. L. Brown

Coal has been transported by belt conveyors in mines for many years; however, only since the beginning of the general mechanization period have complete transportation system of this type been employed. Aside from my complete belt-conveyor transportation systems, belt conveyors are frequently used in conjunction with other transportation. Many early installations, for the most part, were made without standards as a guide. As a result, some States have outlined certain requirements based more or less on experience following mine fires. Correlation of these regulations should result in more uniformity in connection with standardization of regulations. The National Electrical manufacturers Association has published standards for mining-belt-conveyor installations2/ that should be helpful to the coal-mining industry generally. Bureau of Mines Schedule 2F3/ requires certain controls for permissible-belt- conveyor drives, and similar requirements are listed in Bureau of Mines bulletin 514.4/ Committees of the American Mining Congress have prepared much valuable information concerning operation of belt conveyors, and a subcommittee on fire-resistant belting has been active. 5/

Jan 1, 1956

By Daryl E. Radcliffe

The Bureau of Mines studied the displacement of the roof in a portion of the Bear coal mine near Somerset, Colo, Horizontal-and vertical-displacement gages were installed in a five-entry section during normal room-and-pillar mining procedures. Monitoring of the roof continued until this section was mined out. Displacement measurements in combination with known time lapses between mining and bolting operations indicate that once support is achieved, the length of unsupported time does not appear to affect long-term roof stability in the mine under investigation.

Jan 1, 1978

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Guatemala has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State.

Oct 1, 1929

By Jürgen F. Brune, R. Karl Zipf, Michael J. Sapko

Seals are barriers constructed in underground coal mines throughout the United States to isolate abandoned mining panels or groups of panels from the active workings. Historically, mining regulations required seals to withstand a 140-kPa (20-psig) explosion pressure. However, the Mine Improvement and New Emergency Response Act (“MINER Act”) requires the Mine Safety and Health Administration (MSHA) to increase this design standard by the end of 2007. This report provides a sound scientific and engineering justification to recommend a three-tiered explosion pressure design criterion for new seals in coal mines in response to the MINER Act. Much of the information contained in this report also applies to existing seals. Engineers from the National Institute for Occupational Safety and Health (NIOSH) examined seal design criteria and practices used in the United States, Europe, and Australia and then classified seals into their various applications. Next, the engineers considered various kinds of explosive atmospheres that can accumulate within sealed areas and used thermodynamic calculations and simple gas explosion models to estimate worst-case explosion pressures that could impact seals. Three design pressure-time curves were developed for the dynamic structural analysis of new seals under the conditions in which those seals may be used: unmonitored seals where there is a possibility of methane-air detonation or high-pressure nonreactive shock waves and their reflections behind the seal; unmonitored seals with little likelihood of detonation or high-pressure nonreactive shock waves and their reflections; and monitored seals where the amount of potentially explosive methane-air is strictly limited and controlled. Figure 1 is a simple flowchart that illustrates the key decisions in choosing between the monitored or unmonitored seal design approaches and the three design pressure-time curves. For the first condition, an unmonitored seal with an explosion run-up length of more than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections exists. The recommended design pressure-time curve rises to 4.4 MPa (640 psig) and then falls to the 800-kPa (120-psig) constant volume (CV) explosion overpressure. For unmonitored seals with an explosion run-up length of less than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections is less likely. A less severe design pressure-time curve that simply rises to the 800-kPa (120-psig) CV explosion overpressure may be employed. For monitored seals, engineers can use a 345-kPa (50-psig) design pressure-time curve if monitoring can ensure that (1) the maximum length of explosive mix behind a seal does not exceed 5 m (16 ft) and (2) the volume of explosive mix does not exceed 40% of the total sealed volume. Use of this 345-kPa (50-psig) design pressure-time curve requires monitoring and active management of the sealed area atmosphere. These design pressure-time curves apply to new seal design and construction.

Jan 7, 2007

By C. B. Manula, R. L. Sanford, R. A. Rivell

PART I. FLOW CHARTS

Jan 1, 1974

By Takashi Ohya, George V. Keller, Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications system which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a rela- tively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurements of ambient surface electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal-to-noise ratio at the surface. Numerous C.W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surface magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null in the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

By D. A. Reynolds, A. C. Fieldner, S. H. Katz

"03-01-192403-31-2019RI 2591 - Reports of Investigations - Department of the Interior - Bureau of MinesBureau of MinesPittsburgh Experiment Station American Society of Heating and Ventilating EngineersU.S. Public Health ServicesTucson Experiment Station Introduction.""Carbon monoxide self-rescuers,"" or simply ""self-rescuers,"" are pocketsize gas respirators which protect the wearer from air contaminated with poisonous carbon monoxide gas. On March 6, 1924, the Bureau of Mines approved the ""M.S.A. self-rescuer’ manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa., after the M.S.A- self-rescuer bad passed all the tests and requirements of the Bureau's Schedule 14A4.The purpose of the self-rescuer is to help miners to escape from mines in which fires are burning or explosions have occurred, by providing protection from carbon monoxide for at least one half-hour. The self-rescuer can be used similarly by workers above ground who may through accident become surrounded or entrapped by atmospheres containing carbon monoxide.no hazards threaten the miner, who escapes serious injury by fire or violence in a large mine fire namely, ( 1) asphyxiation by poisonous carbon monoxide gas; and (2) suffocation by insufficient oxygen to support life. In order to save himself, the miner must either erect a barrica4e5 against afterdamp and wait restoration of ventilation and rescue or take a long chance at getting out of the mine through entries not permeated by afterdamp.. The self-rescuer removes the hazard of carbon monoxide poisoning for one half-hour or more, and accordingly greatly increases the miner's chance of saving his life.This paper describes the construction and details of the M.S.A. self-rescuer as approved by the Bureau of Mines, and discusses its performance under test condition"

Mar 1, 1924

By A. C. Fieldner

"Purpose and Nature of Tests:The rapidly increasing use of motor vehicles and trucks in the United States is creating an entirely new problem in the proper ventilation of tunnels, subways and other confined spaces through which such machines must pass. This problem has become of immediate importance because a tunnel 3,000 ft. long is being designed to pass under the Hudson River between New York City and New Jersey. Another tunnel at Pittsburgh 5,700 ft. long through the South Hills, is already under construction, and a third tunnel, 6,000 ft. between Boston and Past Boston is proposed. It is probably that other tunnels will be started in various parts of the United States in the near future.The ventilation of such tunnels is a serious matter, on account of the poisonous nature of automobile exhaust gases. It not uncommon to read about finding a man dead in his garage. Generally this happens on a cold, winter morning, after he has been running the engine with the doors and windows closed."

Mar 1, 1920

By S. J. Page, W. E. Wallace, P. Bolsaitis, D. Eppelsheimer, M. J. Keane, J. Poston, J. Harrison

"Respirable-sized dust particles from a clay mine and mill were examined for aluminium and silicon content by scanning electron microscopy-energy dispersive X-ray analysis at incident electron energies of 5--20 keV. Most of the high silica content particles, those which had a silicon to silicon plus aluminium signal fraction, measured at 20 ke V, of0.9 or greater, showed a decrease in the silicon fraction of signal with decreasing incident electron energy, down to values of between 0.6 and 0,8 at 5 keV: this decrease was a function of particle size and composition. Simple models for silicon fractiol) of signal vs incident electron voltage suggest this behavour is due to a heterogeneous particle structure in which an aluminosilicate coating occludes the surface of a silica particle core. The coating survives incubation in a major component of pulmonary surfactant.INTRODUCTIONMINING and some other dusty workplace atmospheres are monitored for respirable dust and quartz dust for purposes of occupational health protection, respirable quartz dust being a known cause of pulmonary disease. Respirable quartz exposure data are acquired also for epidemiological research on the correlation of pulmonary disease prevalence with respirable dust composition and concentration. For these purposes quartz content often is measured on collected dust samples by X-ray diffraction or in spectroscopy. Scanning electron microscopy-energy dispersive X-ray analysis spectrometry (SEM-EDX) is also used. The first two methods measure the bulk composition of a multi-particle dust sample; SEM-EDX measures the elemental composition of single ·particles. These methods as typically applied, including SEM-EDX with a 20-30 kilo-electron volt (keV) electron beam accelerating potential, do not distinguish homogeneous distribution of impurities in a particle from possible heterogeneous surface distribution. These measurements of quartz content are not always accurate predictors of the prevalence of dust-induced disease (ROBOCK and BAUER, 1990), which implies that the biologically available quartz surface may not be equivalent to conventionally measured quartz content of respirable dust in some exposure settings. Using a minor modification of conventional scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) protocols on samples of settled and airborne dust from a clay mine and mill we have detected heterogeneity with depth for aluminium impurity in high silica content particles, indicating that some of the quartz or 'free silica' respirable particles of the dust are aluminosilicate occluded. Coatings were not removed by incubation of the dust in a surrogate pulmonary hypophase surfactant fluid."

Jan 1, 1990

By G. K. Derby

The Bureau of Mines studied the problems caused by airborne contaminants from welding exhaust in surface mining operations and investigated equipment designed to reduce existing hazards. Four commercially available welding-fume exhaust units were tested to determine their effectiveness. Results indicated that the four units had the capability of controlling airborne particulate concentrations and bringing them to within allowable exposure limits.

Jan 1, 1981

By Je M. Oh

The Bureau of Mines is conducting research to determine the high temperature oxidation resistance of substitute stainless steels (SS) containing two less strategic elements, Al and Si, instead of Cr. Chromium is considered to be a critical and strategic metal. Although the Cr content was reduced to 8 wt pct, the alloys showed better oxidation resistance than did 304 SS containing 18 wt pct Cr. Specifically, the alloys that contained Fe-8Cr-16Ni with combinations of Al and Si showed excellent oxidation resistance even at temperatures up to 1,000° C. In this study, the effects of the alloying elements on oxidation kinetics and morphology of oxides were investigated using a Cahn Rg electrobalance, scanning electron microscopy, an energy-dispersive X-ray analyzer, X-ray diffraction, and an electron microprobe. Aluminum and silicon additions in combinatin were more effective in providing oxidation resistance than either element was alone.

Jan 1, 1986

By J. L. Ambs

The U.S. Bureau of Mines (USBM) Diesel Research Program emphasizes the development and evaluation of emission control devices to reduce exposure of miners to diesel exhaust pollutants. Studies by the USBM have shown that diesel exhaust aerosol (DEA) contributes a substantial portion of the respirable aerosol in underground coal mines using diesel equipment not equipped with emission controls. The USBM and the Donaldson Co., Inc., Minneapolis, MN, have developed a low-temperature, disposable diesel exhaust filter (DDEF) for use on permissible diesel haulage vehicles equipped with waterbath exhaust conditioners. These were evaluated in three underground, mines, to determine their effectiveness in reducing DEA concentrations. The DDEF reduced DEA concentrations from 70 to 90 pct at these mines. The usable life of the filter ranged from 10 to 32 h, depending on factors that affect DEA output, such 'as mine altitude, engine type, and duty-cycle. Cost per filter is approximately $40.

Jan 1, 2010

By Scott Turner

We are here today to witness the graduation of 63 young men as Engineers in the mineral industries . It is an important occasion and one in which the public takes a keen interest , since this school has long been famous for the educational facilities it affords young men, and for the high professional standing of its graduates . : : : It is fitting that once each year we should pause to review the path the student has traveled , and to reflect upon the perspective opening before him as an engineer . I was invited to come from Washington to take part in this ceremony and to say something to these young graduates . In searching for a theme ," it occurred to me. that perhaps my best contribution would be to duscuss certain beliefs as to college training , deal with the situation in which the young engineer finds himself on graduation , touch on the new ideas of the social and political responsibilities of the engineer , and point out what he may expect to find in practice , and , above all , what he must do to orient himself properly in the mining profession and maintain the best traditions of our brotherhood . Let us first review your college days and see what they have done for you . I am told there are still many temptations in college . I know there used to be . Rest assured the same holds true in the professional life ahead of you. The main difference is , perhaps , that your greatest temptations in college were those offered by your teachers , who tried to entice you into realms of harder work, closer application , increased concentration , clearer thinking and better understanding , by animating your curiosity and increasing your powers of reasoning and of observation . In other words , here you have carefully and systematically been decoyed toward finer and loftier things . Do not expect that similar helpful influences will greet you on every side in your professional life . Often quite the contrary is the case .

Oct 1, 1930