Search Documents

By J. W. Griflith, P. A. Mack, C. M. Lang, S. Riling

"N-acetyl-beta(B)-D-glucosaminidase is a N-acetyl-beta((B)-D-glucosaminidase enzyme se¬creted by alveolar macrophages in response to phagocytosis of particulate material. Alveolar macrophages participate in the degradation and fibrosis of pulmonary tissue that results in pneumoconiosis. Known quantities of four characterized respirable dusts were bronchoscopically placed into the right caudal lung lobe of macaque monkeys. Bronchoalveolar lavage (BAL) samples were collected from dust-exposed right lung and unexposed left lung of the same individuals at 2-week intervals for 12 weeks after dust instillation. The samples were tested for N-acetyl-B-D-glucosaminidase activity to determine if the enzyme levels could serve as an indicator of pulmonary injury induced by generic coal dusts when compared to known fibrogenic and nuisance dusts. Installation of generic quartz, anthracite, or TiO2 dusts produced significant elevations of enzyme activity and increased numbers of macrophages in the dust-exposed lobes. Elevations in enzymatic activity and macrophage numbers were greatest in response to generic quartz dust. These results suggest that quantitative levels of N-acetyl-B-D-glucosaminidase activity may be a useful indicator of acute and chronic lung injury following exposure to fibrogenic and nonfibrogenic dusts.IntroductionCoal workers pneumoconiosis (CWP) is an occupational pulmonary disease associated with the inhalation of coal mine dust. An important external factor in the development of CWP is the composition of the respirable coal mine dust. A cause-and-effect relationship exists between coal mine dust and CWP, but it has not been shown that exposure to generic coal dusts will cause CWP [12]. Numerous immunological, biochemical, and cellular changes occur in CWP; however, in this study, only N-acetyl-beta(B)-D-glucosaminidase (NAGase), protein, and alveolar macrophages (AM) will be examined [7, 32, 33]."

Dec 1, 1996

By David L. Veith

Caustic scrubbing followed by silica flotation with cationic ether primary amine proved effective in upgrading commercial magnetic concentrates to supergrade products containing 2 percent SiO2, or less. Samples representing 41 million long tons per year of commercial magnetic concentrates from the Lake Superior region were tested by the Bureau of Mines. Bench-scale and pilot plant research indicated an estimated potential of 32 million long tons per year of superconcentrates to be available. Two pilot plant investigations yielded superconcentrates containing 1.1 and 1.9 percent SiO2 that were derived from commercial concentrates containing 7.0 and 4.2 percent SiO2, respectively. Corresponding iron recoveries were 90 and 93 percent at reagent costs of just over 33 cents per long ton of superconcentrates produced. Additional sources evaluated on a bench scale resulted in iron recoveries of 72 to 95 percent in products containing 1.7 to 2.0 percent Si02. Although reagent cost ranged up to 60 cents per long ton of superconcentrate, it is probable that these costs would be reduced in plant applications where benefits are derived from material and reagent recycle.

Jan 1, 1974

By J. A. Ruppert

The Bureau of Mines investigated methods of refining iron-contaminated zinc to marketable quality and developed a laboratory-scale process in which aluminum, added as a refining agent, reacted with the iron, forming solid Fe2Al which floated to the surface of the melt. Solids were separated by both filtration and centrifugation, using a unique type of "dipping" centrifuge devised during the work. Typical zinc recovery was 95 percent, and iron content of the metal was lowered from 0.37 to 0.02 percent.

Jan 1, 1967

By H. M. Smith

Data from the Bureau of Mines routine method for the analysis of crude petroleum are used to characterize crude oils. Some data are used directly while other data are used to calculate the aromatic) naphthene) and paraffin contents of the distillation fractions and the correlation index of the paraffin-naphthene portion of the fractions. The calculated properties show significant differences in composition between crude oils. The methods of calculation and interpretation of data are explained and illustrated.

Jan 1, 1966

By L. J. Kane

While analyzing synthesis gas produced from coal, the Bureau of Mines found that conventional procedures for naphthalene determination were difficult and time consuming. The Bureau developed a rapid and sensitive turbidimetric procedure, which requires only simple instruments and hence can be used in plant-control laboratories. The gas is passed through a saturated aqueous solution of picric acid at 3° to 4° C. whose turbidity is then measured at room temperature. A dispersing agent is added to prevent coagulation of the suspension on warming. Only about 1 mg. (0.015 grain) of naphthalene need be absorbed, and precision and sensitivity are a few ten-thousandths of a grain, or a few hundredths of a grain per 100 cubic feet. The determination can be completed less than 10 minutes after absorption. INTRODUCTION One of the functions of the Branch of Coal Gasification, Bureau of Mines, Morgantown, W. Va., is to develop economical methods for manufacturing, from coal, a mixture of hydrogen and carbon monoxide for producing hydrogen, methane, and other gaseous fuels. This raw gas may contain many impurities, including naphthalene. This impurity is usually determined by first forming naphthalene picrate in a water solution of picric acid, separating the picrate, and titrating the unreacted picric acid or the picrate itself.

Jan 1, 1957

By John W. Cole

As part of a general preliminary investigation of lead-zinc deposits in Stevens County, Wash., the Electric Point and Gladstone mines on Gladstone Mountain, in the Northport Mining District, were examined by R. M. Gammell, an engineer of the Bureau of Mines, in June 1946. A trenching and sampling program was executed later the same year under' the supervision of Miro Mihelich and the author. This report presents the factual data obtained from the trenching and sampling operations.

Jan 1, 1949

By A. F. Colombo, R. T. Sorensen, D. W. Frommer

The Bureau of Mines developed a flotation method for concentrating spiral tailing produced from pilot plant tests on the Champion mine ore fines . The feed material contained about 49 percent Fe and 15 percent SiO2 and was posed mostly of specular hematite , muscovite , and chlorite . Bench- scale , batch flotation research developed a reagent suite composed of tall oil - fatty acid , fuel oil , sulfuric acid , sodium fluoride , and sodium silicate for recovery of iron minerals in the froth product . Concentrate made with the reagent suite contained 87.3 percent of the iron and analyzed 65.6 percent Fe and 1.9 percent SiO2 . Continuous flotation tests were made with a nominal feed rate of 400 lb /hr , but without middling recirculation . Using nearly the same amount and complement of reagents as in the batch tests , three similar continuous tests gave concentrates averaging 63.9 percent Fe and 3.1 percent Sio while recovering about 86 percent of the iron .

Jan 1, 1964

By Arden D. Fugate

The Federal Bureau of Mines conducted extensive studies on solid-state defluorination (laboratory scale) and tests on molten defluorination (intermediate scale) of siliceous fluorspars. The studies were made to develop a pyrohydrolytic process for liberating fluorine from offgrade fluorspars. Test results showed that more than 90 percent of the fluorine can be evolved by solid-state defluorination at 1,300° C., and more than 97 percent can be liberated by molten-state defluorination at 1,420° C. Solid-state defluorination conditions were established by conducting tests on mixtures of ceramic-grade fluorspars and high-purity silica flour. Pelletized mixtures were defluorinated under varying conditions of time, temperature, and relative concentrations of silica, calcium fluoride, and water. The effects of adding various amounts and combinations of aluminum oxide and iron oxide on defluorination were also studied. Investigations of solid-state defluorination indicates that the following two reactions are involved: 2CaF2 + 3SiO2 = 2CaSiO3 + SiF4, and CaF2 + Sio2 + H20 = CaSiO3 + 2HF, The second reaction is dominant, although significant defluorination can be achieved by the first reaction.

Jan 1, 1961

By R. E. Siemens

The Bureau of Mines sought to correlate the variation of structure-sensitive superconducting properties with microstructure in selected Cb-Hf alloys and to compare the experimental results with those predicted by the GLAG theory. Alloys in wire and rod form were evaluated by critical temperature, critical current, magnetization, resistivity measurements, and optical and electron microscopy. In the absence of an external magnetic field, the current carrying capacity of columbium was greatly reduced with addition of up to 85 wt pct Hf, but a large increase in Ic occurred for Cb-90 wt pct Hf. Favorable Ic-H behavior was observed in cold-drawn alloys containing 25 and 57 wt pct Hf. Correspondingly, a maximum in Tc occurred at 10-25 and 90 wt pct Hf. Four- or five-hour heat treatment at 600° C resulted in maximum Ic values and maximum hysteresis in magnetization. Dislocation pileup, polygonization, and fine precipitates, responsible for flux pinning, are listed in order of their effectiveness as pinning sites. Sites having an average separation of 1,500 to 3,000 A and a diameter of 1,000 A or less were most effective in influencing Ic-H and M-H behavior. The resistive critical fields increased smoothly to a maximum of 80 k0e between 60 and 65 wt pct Hf. Highfield, mixed state, reversible paramagnetism was observed in some alloys; however, the GLAG theory was in good agreement with experimental results for the majority of the composition range studied.

Jan 1, 1969

By James J. Snodgrass

The Bureau of Mines designed and constructed a series of calibration models for geophysical borehole logging. A nominal hole diameter of 3 inches was selected as representative of typical core holes drilled for mining and engineering purposes, although additional hole diameters of 2, 5, and 8 inches are provided in one of the models for determination of empirical correction factors for variations in hole diameter. The physical properties of the models were determined by laboratory analyses of drill core samples and evaluated statistically for reliability. This report outlines the location of the models, elements of design and construction, and results of the laboratory tests. The models are available at the Denver Federal Center, Denver, Colo., for use by Government agencies and private industry to calibrate logging equipment for measurements of density, sonic velocity, magnetic susceptibility, and electrical resistivity.

Jan 1, 1976

By Martin H. Stanczyk

The direct dissolution of a typical zinc sulfide flotation concentrate by elevated temperature and pressure leaching was investigated. The concentrate assayed about 55 percent Zn, 32 percent S, 6 percent Fe, and 1 percent Pb and contained minor quantities of copper and precious metals. The influence of various factors on the dissolution of the zinc in acidic and ammoniacal pulps when using oxygen as the oxidant was determined. The tests revealed that the sphalerite was difficult to oxidize. Complete dissolution of the mineral required vigorous and intimate nixing of the gaseous, liquid, and sold phases. The addition of pyrite or sulfuric acid to water slurries of the concentrate was required to obtain a high zinc extraction when leaching under acidic conditions. The quantity of pyrite and acid used was about 0.125 and 0.25 pound, respectively, per pound of zinc sulfide contained in the leach charge. In tests with acid, about 96 percent of the zinc was extracted from the concentrate in 1 hour at 200° C. when the oxygen partial pressure was 75 pounds per square inch gage or higher. Leaching with a continuous flow of air as the oxidant gave results that were almost as good as those obtained when oxygen was used, In tests with air fed through the autoclave at 320 liters per hour, 95 percent of the zinc was dissolved in 1 hour, Acid leach solutions assaying approximately 58 grams Zn per liter and containing Fe, Ni, Cr, and Cu impurities were produced in the better tests. The leached residue consisted essentially of red iron oxide together with substantially all of the lead and precious metals.

Jan 1, 1961

By F. K. McIntosh, A. F. Robertson, T. J. Ballard

"INTRODUCTION Molybdenum deposits occur in Halifax County, N. C., near the eastern border of the Piedmont province. The deposits are associated with a small granite body about 2 miles long and half a mile wide. Molybdenite is the principal ore mineral and is found as disseminations or thin stringers in quartz veins and occasionally in the enclosing granite or schist wall rock.The deposits were investigated by Almon F. Robertson and Charles J. Cohen, engineers of the Bureau of Mines, in 1942 and 1943, who recommended that the deposits be explored to supplement reserves of critical war minerals.The Bureau made the initial exploration of the deposits in July 1943 and continued its work to January 1944. Drilling was resumed from July to December 1946 to test the deposits at &eater depth than had been attempted during the previous exploration."

Dec 1, 1947

By J. B. Gayle

Since the turn of this century, there has been increasing interest in the application of flotation processes to the beneficiation of finely divided minerals of various types, This is reflected by the large numbers of papers dealing with various aspects of this problem published annually both in this country and abroad. For the most part, such papers fall into one of three categories: 1. Those concerned with achieving, by various chemical and/or physical means, a set of conditions under which certain particles become potentially floatable while others do not. 2. Descriptive studies of plants and pilot plants effecting separations between such particles. 3. Studies of the effects of certain design and operating variables on the rates and efficiencies with which such separations can be effected.

Jan 1, 1959

By R. P. Walters, M. J. Lynch, D. R. Flinn

The Bureau of Mines evaluated tthhee feasibility of substituting platinum- coated metals for bulk platinum shapes as a means for conserving platinum . Platinum coatings were prepared using four different methods of electrodeposition , then tested and evaluated . In order for platinum coatings to be useful in process environments , they must be thick , adherent , stress - free , and pore - free . The Bureau evaluated direct - current , current reversal , cathode shielding , and pulsed- current plating techniques for producing a pore-free platinum electrodeposit from a molten cyanide bath . Aqueous corrosion tests of Fe - 10Cr substrates coated with approximately 25 μm of platinum showed that pulse plating yielded the most corrosion- resistant and , hence , the most pore -free coatings . The morphology of coating cross sections was in all cases columnar . The average grain size of pulse -plated deposits was independent of thickness , while all other plating techniques produced grains that increased in size as the coatings became thicker . It is believed that the constant grain size in the pulse - plated deposits resulted from better mass transport during the electrodeposition .

Jan 1, 1965

By J. L. Johnson

The U.S. Bureau of Mines investigated the recovery of tin and silver from the Coal Creek deposit in the Talkeetna Mountains, AK. Approximately 5 million st of reserves grading 0.2 pct Sn with silver credits of 0.2 tr oz/st have been delineated by drilling. A 10-to 25-pct Sn gravity concentrate was produced by treating the minus 20-mesh ore with a spiral, then regrinding to minus 65 mesh and tabling. Sulfide contamination in the gravity concentrate was as high as 60 pet. Sulfide flotation of this concentrate produced tailings containing 40 to 50 pet Sn. Overall recovery was 76 pct for tin but only 5 to 10 pct for silver because of losses during sulfide flotation. Other methods tested to clean the concentrate included cassiterite flotation, gangue flotation, nitric acid leaching, and wet and dry magnetic separation. Tin beneficiation tests on the minus 325-mesh fraction included cassiterite flotation, vanning, sulfide flotation, and fuming. The bench-scale and locked-cycle tests were used to estimate the mass flows for a 1,000-st/d plant.

Jan 1, 2010

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

By D. Harrington, C. W. Owings

The mining industry is gradually realizing that safety education and safety inspection are economic factors that may not be overlooked as a means of reducing operating costs . Many mine operators , however , have failed to realize the benefits of safety , and the efforts of the more progressive mining companies are offset by the carelessness of neighboring companies when the accident records of a community or a State or the nation as a whole are considered . This tendency is indicated by the data collected by the safety division of the United States Bureau of Mines . During the fiscal year ended June 30, 1930 , relatively definite information: was secureä concerning 34 mine explosions , 24 mine fires , and 29 miscellaneous accidents ; these accidents are by no means all of the explosions , fires , and miscellaneous accidents which occurred in the mines of the United States during the period; but the data on the fires and explosions constitute a record of all of those types of accidents that were called specifically to the attention of the safety division , and the miscellaneous accidents include those on which definite , detailed data were obtained by the safety division .

Jan 1, 1931

By Alice V. Peter

The rare-earth group are among the least familiar of the 92 known elements. Moreover, the relatively few people who have even heard of the rare earths ordinarily regard them merely as very rare elements having unusual names but doubtful commercial application. This typical attitude can be attributed partly to the fact that no commercial uses have been developed for most of the members of the group and partly to the fact that those which do enter into useful articles do so anonymously. Most people speak with a degree of familiarity of the "chromium" plating on their automobiles or household appliances; "antimony" ash trays and cigarette boxes are on sale in many department stores; and "tungsten" lamps and even "molybdenum" steels are advertised in popular magazines. However, the average user of a pocket cigarette lighter is not conscious that the important sparking element is a "flint" made from ferrocerium, and if he does chap on to inquire about the composition he is likely to be told that it is "sparking alloy", "misch metal", or 'pyrophoric alloy." Similarly, the wearer of spectacles made of "Crookes" or other tinted glass probably is not aware that the light softening effects are due to the presence of rare-earth oxides, or that the arc light on his street may owe its brilliance to cerium fluoride in the carbon electrode. Despite a variety of practical applications, however, most of the rare-earth metals still must be listed as scientific curiosities. In fact, little is known as to the properties which may make them useful products at some future date. Meanwhile it is important to note that Nature has been relatively generous in her distribution of the rare earths and that adequate supplies of most of them will be forthcoming when these elements have proved their worth as commercial products.

Jan 1, 1935

By D. R. Hanson

This Bureau of Mines study examines the acoustic vibrational spectra of rock slabs in the range of 0 to 5,000 Hz. The power spectra of so-called drummy rocks were found to be diagnostically enhanced in the range of 200 to 1,000 Hz. Comparison of the power in this band with that in a band from 3,000 to 3,500 Hz provides a quantitative measure of rock stability. A prototype field instrument was designed, constructed, and field-tested. This battery-powered instrument computes the power contained in the two frequency bands mentioned, compares the magnitude of these two quantities, and displays a number that is related to the detachment of the block tested. Field tests show that this instrument is capable of giving reliable measurements of block stability under conditions of noise and dust that would seriously degrade the accuracy of normal sounding techniques.

Jan 1, 1985

By John J. Sammarco

The functional safety of programmable electronic (PE) mining systems is an international issue and concern. From 1995 to 2001, 11 PE-related mining incidents in the U.S. were reported by the Mine Safety and Health Administration (MSHA); 71 PE-related mining incidents were reported in Australia. MSHA does not have regulations for formal evaluations of the functional safety of PE mining systems. Hence, the National Institute for Occupational Safety and Health (NIOSH), in partnership with MSHA and the industry, generated the NIOSH safety framework for functional safety of PE mining systems. An overview of the NIOSH framework is given; the key framework elements, the safety life cycle and safety integrity levels are detailed. The safety framework approach has impacted the national and Australian mining industries by enabling the industries to advance from an ad-hoc approach to a formalized and systematic functional safety process. In retrospect, valuable lessons were learned for addressing functional safety and for changing industry perspectives and practices. These lessons continue to benefit mining and are applicable to other industries as well.