Search Documents

In the United States water pollution resulting from mining activities has long been recognized as a major environmental problem Mine drainage pollution results from many types of mining activities and includes both physical (i e , sedimentation) and chemical (i e , acidification, metal contamination, etc ) pollutants Active and abandoned surface and underground mines, mineral processing plants, mine and processing plant waste disposal areas, haulage roads, and tailing ponds are typical sources of mine related water pollution (130) One of the most serious pollution problems arising from mining activities is acid mine drainage resulting from the chemical reaction of sulfide minerals (commonly iron sulfides) and air in the presence of water Acid mine drainage is commonly associated with coal and hard rock mining areas in the United States In general the more serious and extensive acid mine drainage problems exist in the more humid coal regions east of the Mississippi River (11) In 1964 the U S Department of the Interior, Fish and Wildlife Service, reported that acid mine drainage adversely affected fish and wildlife habitat in 9,477 kilometers (5,890 miles) of streams and 6,062 hectares (14,967 acres) of impoundments in 20 states in the United States (64) Of the total affected waters, coal mining operations accounted for 97 percent of the acid mine drainage pollution reported for streams and 93 percent of that reported for impoundments In 1970 more than 19,308 kilometers (12,000 miles) of streams in the United States were reportedly significantly degraded by mining related pollution (130) Of the total affected kilometers, 16,920 kilometers (10,516 miles) or approximately 88 percent were located in the Appalachian coal region (Pennsylvania, West Virginia, Ohio, eastern Kentucky, Tennessee, Maryland, and Alabama) In addition, more than 965 kilometers (600 miles) of streams reportedly were degraded by coal mining in states in the Illinois, Western Interior, and Rocky Mountain coal regions The remaining portion of the stream pollution resulted from the mining of (1) copper (california, Montana, Nevada, New Hampshire, Tennessee, Virginia, and Wyoming), (2) lead and zinc (Colorado, Idaho, Kansas, Missouri, Montana, Oklahoma, and Tennessee), (3) uranium (Rocky Mountain States), (4) iron (Lake Superior iron region), (5) sand and gravel (all states), (6) phosphate (Florida and other states), (7) gold (Alaska), (8) bauxite and barite (Arkansas), and (9) molybdenum, gold, and other metals (Colorado) Abandoned mines and abandoned mine waste disposal areas contribute a large portion of the total pollution resulting from mining activities Numerous abandoned underground mines are located throughout the United States and many are discharging mine drainage pollutants In 1966 the U S Bureau of Mines estimated that more than 88,000 inactive and abandoned underground mines were in existance (126) A listing of these mines by state is presented in Table 1 0-1 More recent estimates indicate that this list is incomplete In Colorado alone there is

Jan 1, 1975

By V. A. Marple, K. L. Rubow, B. A. Olson

"INTRODUCTION Inertial classification, gravitational sedimentation centrifugation, and thermal precipitation arc techniques that can be used to collect particles for subsequent analysis or for particle classification. The inertial classifiers, which include impactors, virtual impactors, and cyclones, are widely used in the sampling or particles. Settling chambers, which include centrifuges as well as gravitational settling devices, are less widely used. Thermal precipitators arc seldom used.Impactors, in particular, have been used extensively, studied both theoretically and experimentally, and arc the instrument or choice for the determination or aerosol mass size distributions. Many versions or impactors arc available commercially and many more have been designed, built, and used in special studies.Virtual impactors are a more recently developed inertial classifier and possess a feature not round in conventional inertial impactors; namely, that the particles remain airborne after classification compared to the conventional impactor, where the particles arc collected on a solid surface. The feature or keeping particles airborne is important for transporting the particles to other particle-analyzing instruments, or to filters, and in concentrating particles larger than the cutsize in a small fraction of the total now."

Nov 1, 1995

By L. D. Tracy

This paper represents work conducted by the Bureau of Mines in cooperation with the Illinois Geological Survey and the Engineering Experiment Station of the University of Illinois.

Jan 1, 1926

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom of wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is

Jan 1, 1980

By Douglas A. Elkins

The unique characteristics of plasmas, their current applications, and ongoing research into new applications are described. Major technical and economic problems in application of plasma technology are discussed. Examples of potential applications of plasma in extractive metallurgy are described and evaluated. The report includes a selected bibliography of articles on plasma and related high-temperature technology.

Jan 1, 1969

By W. P. Yant

A previous report of the Bureau of Mines dealt with the toxicity of dichlorodifluoromethane, a new refrigerant that has a remarkably low toxicity. Continued research by the Frigidaire Corporation and toxicological experiments performed in the Laboratory of Applied Physiology of the University of Cincinnati revealed another organic fluoride, dichlorotetrafluoroethane, whose toxicity also appeared to be of a very low order and whose physical and chemical properties make it suitable for refrigeration purposes. In addition to low toxicity, safety in its use is further enhanced by its physical properties, which permit the design of equipment that operates at comparatively low pressures and hence mitigates the dangers and problems of leakage. The investigation described in this report was performed by the Bureau of Mines at the request and with the cooperation of the Frigidaire Corporation.

Jan 1, 1932

By C. W. Owings

"PURPOSE OF REPORTThe safety and efficacy of permissible storage—battery gathering locomotives are becoming recognized more and more in coal mines. The great mobility of this type of haulage equipment is due to the fact that no trolley wire and bonding of rails are needed; hence wherever there is track and adequate ventilation to dilute properly any dangerous gases, the storage—battery gathering locomotive may go. As coal near the outcrop or the surface is mined out, coal farther from the outcrop or deeper in the ground must be mined, and gassiness of the coal bed often increases under these conditions. The use of electrical equip¬ment capable of giving off arcs or sparks while operating near or at the coal faces constitutes a serious explosion hazard. Often, it is uneconomical or impracticable to use animal haulage, and locomotives must be employed. The operator should consider the safest and most economical unit; permissible equipment is the answer to this problem, and storage—battery locomotives are the only permissible electric haulage units.A comparison of permissible storage—battery locomotives with cable—reel locomotives of the latest enclosed ""explosion—tested"" type has been made at the Keystone No. 1 mine of the Houston Collieries Co., at Keys one, W. Va. The information and data contained in this publication were obtained by the writer during an inspection of haulage at this mine.ACKNOWLEDGMENTSThe writer is indebted to P. C. Thomas, vice president and general manager, the Koppers Coal Co., operator of the Keystone mines, who granted permission for making the study. W. A. Wilson, general superintendent, Houston Collieries Co., arranged for the investigation and for obtaining the data. C. E. Zuspan, chief electrical inspector, and J. C. Newman, division electrical inspector, accompanied the writer underground and assisted materially in obtaining information and data upon the haulage methods and performance of the locomotives. The assistance or general mine Foreman Pierman and of mine foreman White is gratefully acknowledged."

Aug 1, 1931

By Bill M. Stewart

To decrease the potential for fine coal waste slurry impoundment failures, the Bureau of Mines investigated a new disposal technique. The fine coal waste slurry is rapidly thickened (i.e., dewatered) and deposited on a slightly sloping surface. To accomplish rapid dewatering, a chemical flocculation system using polymers was developed to treat the fine coal waste slurry stream. The fine solids formed flocs, settled from suspension, and rapidly released excess water. During the last 5 days of the field test, slurry flowing at rates from 498 to 675 gal/min with a specific gravity range of 1.15 to 1.33 was successfully treated and dewatered. During this period, untreated slurry had an average moisture content of 227.4 pct (30.7 wt pct solids). The effectiveness of the dewatering system was determined by monitoring the moisture content of the deposited waste with respect to time. Sixty-five hours after ending the field test the average moisture content was 54.9 pct (64.5 wt pct solids); 68 days after the field test the average moisture content was 28.8 pct (78.0 wt pct solids).

Jan 1, 1986

By Carroll W. DeKock

Thermodynamic data for selected metal sulfates were critically evaluated and compiled as part of the Bureau of Mines program to provide a scientific base for use in developing new technology and predicting the feasibility of new processes. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?RC, ?Gf°, and log Kf as functions of temperature are given in tabular form. Thermodynamic data were compiled for Ag2SO4, A12(504)3, A12(S04)3?6H20, BaSO4, BeSO4, BeSO4?2H2O, BeSO4?4H20, CaSO4, CaSO4?1/2H20, CaSO4?2H2O, CdSO4, CdSO4?H20, CdS04?8/3H20, 2CdO?CdSO4, Cs2SO4, In2(S04)3, K2504, KA1(S04)2, KA1(S04)2?12H20, Li2SO4, L12SO4?H20, MgSO4, MgSO4?H2O, MgSO4?2H20, MgS04?4H20, MgS04?6H2O, MgS04?7H2O, Na2SO4, Na2S04?7H20, Na2SO4?10H20, (NH4)2SO4, NH4A1(S04)2, NH4A1(S04)2?12H20, PbSO4, Rb2SO4, T12SO4, and Zr(S04)2.

Jan 1, 1986

By D. A. Reynolds, J. D. Davis

"This work was begun in l928, with the cooperation of the American, Gas Association, and the Association contributed financial aid for that year and for the 4 years following. In 1933 financial aid was discontinued, but the Advisory Committee, under the able, Chairmanship of J. S. Haug, has continued to function through the years to the present date. Mr. Haug's annual reports have been published in the Proceedings of the American Gas Association. The purpose of this paper is to bring the index of coals tested by the Bureau of Mines-American Gas Association (EM-AGA) method up to date, to discuss development of auxiliary tests, and to outiline the uses to which the methods have been put in promoting the war effort.COALS TESTEDThe test methods developed with the advice of the Advisory Committee had been applied to 66 coals up to 1942, and an index giving the serial number, origin, and analyses of these coals was published as Bureau of Mines Technical Paper 637. Since this paper was published, 20 additional coals have been tested; the source and analyses of these coals are given in table 1. The table also refers to publications that have been issued. Complete series of tests at high, medium, and low temperatures,have been made on most of these coals, and blending tests with 20 and 30 30 percent of low-volatile coals have also been made at 900°C.; however a few low- and medium-volatile coals (60, 70, 74, 79, and 80) were bested,at high temperatures only. Those coals were mined in eastern Oklahoma and western Arkansas. The test work included low- and high-temperature assay tests, petrorraphic analyses, and plasticity tests since its inception; and for the last 20 coals of the series, expansion and oxidation tests have been made where applicable."

Jun 1, 1944

By S. D. Cramer

Corrosion research is being conducted by the Federal Bureau of Mines to determine suitable construction materials for geothermal resource recovery plants. As part of this research, the corrosion resistance of 31 iron-nickel-, aluminum-, copper-, titanium-, and molybdenum-base alloys was characterized and evaluated in laboratory corrosion studies in low-and high-salinity geobrines representative of those found in the Imperial Valley, Calif. General, crevice, pitting, weld, and stress corrosion were measured at 105° and 232° C in deaerated brines and brines containing dissolved 02, C02, and CH4 General corrosion rates in deaerated brines at 105° and 232° C were usually below 5 mpy for the alloys tested except carbon steel, the low-alloy steels, Monel 400, 70-30 cupronickel, and the aluminum-base alloys. Dissolving carbon dioxide and methane in the brines at 2320 did not markedly alter these results. However, the introduction of oxygen, which can enter the brine during process operations, seriously degraded the corrosion resistance of many alloys by increasing the incidence of stress corrosion cracking, crevice corrosion and, except for the titanium-base alloys, pitting. In deaerated brine at 2320 C, the general corrosion rates for carbon steel and the low-alloy steels were relatively unaffected by pH in the range of 6.1 to 3.0. However, general corrosion rates increased sharply below pH 3.0. In deaerated brine at 232° C, welds in several iron-, nickel-, and titanium-base alloys corroded at rates comparable to the general corrosion rates of the alloys, but the addition of oxygen to the brine increased corrosion rates for welds in Inconel 625 and E-Brite 26-1. Alloys exhibiting good corrosion resistance in the deaerated Salton Sea KGRA-type brine at 232° C were E-Brite 26-1, Inconel 625, Hastelloy S, Hastelloy G, Hastelloy C-276, TiCode-12, Ti-0.2Pd, Ti-2Ni, Ti-1.7W, and TZM. The alloys most resistant to corrosion in oxygenated Salton Sea KGRA-type brine at 232° C were the titanium-base alloys. These alloys appear the most suitable for use in the construction of geothermal resource recovery plants. Carbon steel and the low-alloy steels are unsatisfactory for high-temperature, high-salinity brines and alternative low-cost materials with improved corrosion resistance should be sought.

Jan 1, 1980

By Walter I. Enderlin

To economically extract ore from great depths in the earth while sustaining an acceptable working environment will require the development of new technology and equipment, involving large capital expenditures. Moreover, careful analysis and advance planning will be required. But, the literature is lacking in data pertaining; to the thermal properties of various host rocks and to quantities of heat generated by various underground heat sources. This types, of data is required to forecast nine heat loads during advanced planning and design. This thesis sets forth a practical method for evaluating underground sources of heat in deep mines and provides an improved information base. Moreover, seven topics for further research are recommended. The heat sources considered are: wall-rock, ground water, adiabatic compression, equipment, service lines, blasting, metabolism, curing of cement, and oxidation of sulfides and timber. Seven deep metal mines with high production rates and high heat loads were visited to obtain data necessary to assess their thermal environments. Mine records were examined, wall-roc:, temperatures were measured and a survey of the mine ventilating air and mine drainage was performed. Also, the thermal conductivity of wet and dry specimens of the host rock were measured in the laboratory. Data analysis disclosed that rock heat and adiabatic compression account for stout 60 per cent of the mine heat load at depth. Equipment currently contributes approximately 20 per cent; however, to offset increasing costs with depth, increased mechanization is anticipated. The treat from ground water averages 19 per cent and the contribution from blasting, metabolism and cement is negligible. Also, approximately [0] per cent of the increase in the enthalpy of the ventilation air is in the form of latent heat. Moisture, however, did not significantly affect the thermal conductivity of the rock specimens measured in the laboratory. Also, from the data, it is evident that a negative correlation exists between the thermal conductivity of the host rocks and the per cent of the heat load derived from the wail-rock. Furthemore, steady state heat flow renditions may be assumed in airways where there has been no major changes in the ventilation system for a period of two years or more. Under these conditions, the author found it more convenient and reliable to compute heat influx using the steady state equation for heat flow into a cylinder, rather than Carrier's method for transient heat flow, which is so often used.

Jan 1, 1973

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in development of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-l Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By E. B. Olds

This paper describes the methods and costs of deepening the 3-compartment underground shaft in the Hooper Tunnel adit at the Bunker Hill & Sullivan Mining and Concentrating Company Crescent mine in the Coeur d'Alene mining region, 7 miles east of Kellogg, Shoshone County, Idaho. The work was done with the aid of a Defense Minerals Exploration Administration contract (No. Idm-E493, Docket No. DMEA-2764). Preparation for deepening the shaft was begun March 26, 1953, and sinking was completed May 27, 1954. The shaft, bottomed at 1,275.5 feet in 1939, was deepened to 3,276 feet, using mechanical mucking and intermediate pockets. A total of 50,349 man-hours was required to complete the work of sinking 2,000.5 feet, cutting 7 pump stations, and driving 2 pocket raises. The rate of advance was 7.1 feet of shaft per operating day, or 8.4 feet per day of actual sinking. The total direct cost for sinking was $205.20 per foot.

Jan 1, 1957

By C. C. Furnas

Despite the fact that a great many industrial processes depend on efficient contact between a gas stream and a bed of broken solids for their operation, the data in the literature are very meager. Several investigations3 have been undertaken, but the work has been limited in scope and application. BUREAU OF MINES PROGRAM OF RESEARCH For the past 10 years the United States Bureau of Mines has been engaged in research with the object of formulating a more or less complete quantitative theory of the workings of the iron blast furnace. Obviously, in order to do this one of the essentials is to have considerable definite information on the laws of gas flow through beds of broken solids. This report in a brief summary of the experimental work on the problem which has been done at the North Central Experiment Station. The complete report with more detailed tabulation of the data and explanations of the experimental procedure is in process of publication in the form of a bulletin.

Jan 1, 1928

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski County, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the eighth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is no followed by a description of each deposit developed in that half township. The 14 half township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations at those holes show on figure 13 in volume I. The descriptions of the deposits developed are followed by complete detailed logs at the drill holes. Many at the widely spaced exploratory holes did not discover bauxite of minable thickness and gra.de. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of manganese from known domestic occurrences. Eight of these deposits were found to have demonstrated resources totaling 420 million metric tons with an average grade of 10 percent contained manganese. They were found to be submarginally subeconomic. Economic evaluations of the eight deposits resulted in incentive prices ranging from $8 to almost $35 per long ton unit (22.4 pounds) of contained manganese. Comparing these prices with the current market value of $1.70 per long ton unit of manganese clearly illustrates the submarginal nature of the domestic ores analyzed. These domestic resources would probably not be developed except in the case of an extreme national emergency. Production from the eight deposits would take 3 to 6 years to develop, and the final product would be manganese ore concentrate, which could be used in the production of ferromanganese. If preproduction development began in 1981, annual production would peak in 1987 with 900,000 metric tons of recoverable manganese. Thereafter, production would see a steady decline unless additional resources were located or technologic improvements were made to allow processing of lower grade material, or unless mining and processing of ocean manganese nodules began to take place.

Jan 1, 1982

By T. E. Swigart

In the production of oil end gas, engineering methods have been applied less than in any other branch of the oil industry. While refineries, gasoline plants, pipe-line and other transportation systems, and even drilling wells to a great extent, take advantage of engineering skill, the tendency has been to assume that the handling of producing wells is merely a mechanical and routine matter. At present few companies employ engineers to study oil and gas production methods with a view of increasing the general efficiency of recovery, but in vie, of the advancement in other lines of the petroleum industry by the application of engineering principles, does it not seem likely that the production branch may benefit also by engineering studies? Engineering applied to the handling of producing wells falls under two general headings, - first, the efficient handling of wells from the time of their inception in order to obtain the greatest possible ultimate production, and, second, the rehabilitation of old properties that have been handled carelessly in their early lives. To date, the engineering work that has been done on oil production problems falls mostly in the second class. For example, the use of vacuum and the application of compressed air have proved successful in some instances in stimulating wells of low gas pressure. These methods are costly to apply and are adapted to small wells in which the gas is almost exhausted, or in which the original gas pressure is negligible. The experiments described in this paper fall under the first heading, as they were made with an idea of learning toe probable extent to which the gas production of an oil well can be curtailed while gas in the sand is still plentiful, and thus saved for doing work during the later period of a well's life. Because of the scope of the experiments, this paper does not include a discussion of back pressure on flowing wells or for purposes other than cutting down the gas produced with each barrel of oil.

Jan 1, 1922

By Frank Ruskey

This report describes a computer program devised by the Bureau of Mines to model coal-mining situations where one or more panels encounter oil or gas wells. The program seeks in several hundred trials to evade the wells if possible or to minimize their influence by shifting or skewing the mine plan and/or adjusting the centerline dimensions of the entryways. Upon completion of computations, the program sorts the hundreds of models which have been tested, and lists the 10 best with their associated parameters. It also draws a mine plan of the best configuration, showing the entryways and crosscuts along with the "lost" coal remaining in the barrier pillars surrounding the various wells.

Jan 1, 1972

By J. L. Konchesky

The technical feasibility of gasifying powdered, noncoking, low-rank coal with steam in an externally heated tube has been demonstrated. The tube, 112 ft. of alloy-steel tubing shaped into a helix, served as an electrical conductor of electricity used for heating. The effects of the following variables were studied: Residence time of coal in reactor, average reaction temperature, steam concentration, and rank or geologic age of coal. Reaction pressure was maintained in the range 19-26 p.s.i.a. High carbon conversions and large yields of synthesis gas were obtained with low-rank coal. In one test, for example, about 88 pct. of the carbon in a subbituminous C coal was gasified at 1,910* F. with a residence time of 1 sec. The gas contained 58 pct. H2, 19 COD 15 CO, and 3 CH4; the yield was 30 cu. ft. (at 32' F. and 14.7 p.s.i.) of synthesis gas (CO + H2) per pound of dry coal.

Jan 1, 1960