Search Documents

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

By Dana C. Reinke

Water well drillers are exposed to high levels of noise while working. NIOSH researchers have found that water well drillers are exposed to levels above 85dB (A) while performing certain tasks during a typical drilling job. Noise levels consistently over 85dB (A) during an 8–hour work shift are hazardous and can lead to hearing loss in workers. Finding ways to reduce noise exposure is difficult because of many factors. The work environment is constantly changing due to the location of jobs and environmental factors. The types of drill rigs required for drilling are expensive. Equipment can range from new to used (10 to 30+ years old). Drillers and owners can work together to prevent noise–induced hearing loss, and measures can be taken to reduce exposure to hazardous noise.[ ] Preventing hearing loss occurs through three stages. The first stage is removing noise from the source (i.e., drill rig). Various parts of a drill rig create noise besides the drilling rod. NIOSH researchers have examined noise levels of drill rigs. Some of the loudest parts of the drill rig include the compressor, engine, and cooling fan (Fig. 1). While removing the noise source from a worksite is ideal, the process would be expensive and difficult.[ ]

Jan 9, 2005

By F. L. Wideman

This report describes the sinking of No. 3 shaft at the Westvaco mine. It is one of a series of publications of the Bureau of Mines on mining methods and practices in the United States. The Westvaco mine is in Sweetwater County, Wyo., approximately 23 miles northwest of the town of Green River (fig. I), There are no permanent habitations in the vicinity of the mine, and employees live in Green River or Rock Springs, Wyo., 14 miles us t of Green River. The mine plant is on a windswept, treeless plain, from which low buttes and flat-topped ridges rise. The altitude at the collar of No. 3 shaft is 6,351 feet. The climate is arid, with temperatures as low as 40° below zero in the winter. Blacks Fork, a tributary of the Green River and a perennial stream, flows near the mine.

Jan 1, 1959

By D. Gearhart

Full-scale tests are conducted on mine roof supports using protocols developed by the National Institute for Occupational Safety and Health (NIOSH) using the unique capabilities of the Mine Roof Simulator (MRS). These protocols simulate the loading conditions that the support will be exposed to in an underground mine to determine the performance capabilities and limitations of the support. Some tests are conducted with rigid boundary conditions, creating uniform contact and near ideal axial loading conditions. These tests are used to determine the ultimate performance potential of a support, including the strength, stiffness, and stability. For prop supports where stability is a critical design issue, tests are implemented to induce buckling by a modified end condition, eccentric contact, or biaxial loading. It is important to determine the cpacity of the support design when the support is subjected to unpredictable loading conditions. This paper examines the effect of end conditions and load profiles on prop support performance and applies a new analysis methodology based on eccentric loading to determine a factor of safety for load capacity. Recommendations for installation practices that minimize eccentricity and therefore preserve capacity are also provided.

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

In 2001, 14,623 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). This was an increase of 210 mining operations compared to 2000. Almost half (49%) were sand and gravel mines, followed by stone (29%), coal (15%), nonmetal mines (5%), and metal mines (2%).

May 1, 2003

By D. A. Reynolds

A few studies on the relationship of the fusion temperature of the ash on coke to that of the corresponding coal have been made on commercial high-temperature cokes. H. J. Rose3/ in 1921 compared the fusion temperatures of the ashes of 10 coals and the cokes produced from them and concluded that they were in such hose agreement that either figure could be used. More recently, Quarfort4/ found that the ash of coke fused at a somewhat lower temperature than that of the original coal. As the ash of a coal and that off tie coke produced therefrom have the same origin their chemical composition should be identical, provided that carbonization has not altered the inorganic, or ash-forming, constituents of the coal, and such alteration seems highly improbable. However, it has been shown5/ that coke is liable to contamination by iron during crushing and grinding preparatory to sampling. Pieters6/ found that coke ash was contaminated in this manner up to 0.4 percent. Extraneous iron would lower the ash-fusion temperature because such iron may form ferrous silicate, which is readily fusible.7/ These results provide a basis for the prediction that the ash of coke will fuse at a lower temperature than that of the corresponding coal, especially if the fine grinding of the coke was done by rubbing -surfaces of iron, as in a disk pulverizer or bucking plate.

Jan 1, 1940

By Karl C. Dean

The Bureau of Mines stabilized 10 acres of windblown copper mill tailings at McGill, Nev., by a combination chemical-vegetative procedure. Legumes, winter wheat, wheat-grasses, and wild rye were seeded, and the area was subsequently sprayed with a resinous adhesive chemical to stabilize the sands until the vegetation could grow. During the year since treatment, the area has been well stabilized against wind erosion. The established vegetation appears to be capable of self-perpetuation and renewal without irrigation. The cost of stabilizing the area was $135.50 per acre.

Jan 1, 1969

By George C. Price

The Bureau of Mines conducted this study in the Roslyn No.5 coalbed in the State of Washington to determine the feasibility of mining hydraulically the portion of the coalbed that was steeply pitching. All of the experimental mining was done while advancing raises and rooms. A Bureau-developed hydraulic mining machine was used successfully in the pitching coalbed. It consisted of a remotely controlled monitor mounted on a self-advancing roof support unit of the type commonly used for roof support in longwall mining systems. The coal cutting rates averaged 0.73 and 0.54 ton per minute in raise and room mining, respectively, while using water volumes up to 230 gpm at a pressure of 4,000 psig. Productivity averaged 4.7 and 5.2 tons per man-shift for raise and room mining, respectively, compared with 7.5 and 8.5 tons per man-shift, respectively, by conventional hand mining methods.

Jan 1, 1965

By W. P. Diamond

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were measured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 670 W -N 280 E (950 separation) for the north, and N 76° W -N 17° E (930 separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By G. R. Hopkins

According to reports received by the United States Bureau of Mines, Department of Commerce, as of January 1, 1929, there were 2,205 cracking units completed or being built in the United States, with a total daily charging capacity of 1,476,874 barrels. A similar survey of a year ago showed 2,334 units of 1,288,000 barrels total capacity. This indicates that despite a decrease in. number of units, there was a material increase in capacity. The year 1928 was, in general, an important one for the cracking branch of the industry. Gasoline consumption reached record levels, prices were higher than in 1927, and it is probable that in the late months of the year the cracking plants were operating very close to capacity.

Jan 1, 1929

By D. E. Pollock, T. W. Beck, J. A. Organiscak

This work presents the findings from a number of NIOSH studies evaluating the impacts of emerging technologies that may reduce dust exposures for continuous mining and roof bolting personnel. These technologies include use of a wet head cutting drum on a continuous mining machine that places water sprays on the cutting drum instead of placing them on a manifold outby the drum. Evaluations at two separate operations showed that the use of the wet head sprays reduced dust levels at the miner operator in the return air, although these reductions were quite variable. NIOSH also assessed the effectiveness of a canopy air curtain for protecting roof bolting personnel. The data showed that dust levels were lower beneath the air curtain than outside the air curtain. This study also suggested several future modifications to the air curtain to in-crease its effectiveness. Finally, NIOSH evaluated mist drilling technology for its effectiveness in controlling respirable dust exposures of bolting personnel. A recent study showed that higher dust levels existed around a machine using the mist system compared to a machine using a conventional vacuum system for dust control. Unfortunately, the true impact of mist drilling was confounded by this machine operating downwind of the continuous miner for much of the study.

By Gregory Molinda

Historically, coal miners have known that roof shales can deteriorate in contact with humid mine air, causing massive roof falls and injuries from falling rock. It is critical to recognize rocks prone to weathering and to adequately support these rocks in order to ensure the long-term stability of the openings. In a recent study, NIOSH has used a wet/dry cycling test to determine the moisture sensitivity of over 800 specimens of roof rock from 25 U.S. coal mines. Fireclays and some gray shales are the most moisture-sensitive. Rocks with disturbed bedding, in contrast to flat-bedded rocks, are also more sensitive to water. Black shales are relatively un-reactive to moisture and serve to protect more reactive gray shales above. Mines that have roof rocks with moisture-sensitivity indexes above 40% can experience slaking roof conditions, and many require high coverage surface controls. Three case studies are presented in which the moisture-sensitivity index is correlated to roof conditions underground, and can be used to indicate long term deterioration. Engineering measures are described to control moisture-sensitive roof. In one case, roof screen not only reduces injuries from rock fall but also is shown to reduce roof falls. Keywords: coal mining, roof control, slaking, roof support, rock falls

Jan 1, 2008

By L. B. Pankratz

Thermodynamic data on the elements and oxides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?HP, ?Gf°, and log K are given in tabular form. Cp°, H° - H°298, ?Hf°, and ?Gf° are also expressed algebraically. Examples of calculations using these data are given.

Jan 1, 1982

A new personal respirable dust monitor developed by Rupprecht & Patashnick Co., Inc. in a multi-year project funded by the National Institute for Occupational Safety and Health (NIOSH) generated promising results in underground coal mine testing performed by NIOSH and industry representatives during the summer of 2003. The mine data showed that the personal dust monitor (PDM) performed similarly to co-located manual reference samplers for full-shift samples at all four underground coal mines at which the evaluation took place. The technology that forms the heart of the PDM, called the tapered element oscillating microbalance (TEOM system), is unique in its ability to collect suspended particles on a filter while simultaneously determining the accumulated mass with National Institute of Standards and Technology traceability. Because the monitor measures the true particle mass collected on its filter, its results do not exhibit the same sensitivity to water spray as do optically based measurement approaches. The technique achieves microgram-level mass resolution even in the hostile mine environment, and reports dust loading data on a continuous basis. Using the device, miners and mine operators have the ability to view both the cumulative and projected end-of-shift mass concentration values, as well as a short-term 15- or 30-minute running average. During underground mine trials in the summer of 2003, technical personnel used the readings from the PDM to identify and correct several abnormal dust generating scenarios. These events demonstrated the potential of the PDM to be used as an engineering tool to evaluate the effectiveness of various dust control strategies. In a separate evaluation performed by CONSOL Energy, Inc., the mine operator evaluated the benefit of a proposed new water spray-based dust control system. Engineers measured the dust concentration upstream and downstream of a production location under different dust control scenarios using two PDM units. By evaluating the change in the dust loading between the upstream and downstream monitoring sites, the company was able to determine in a few hours which hardware configuration would yield the greatest benefit to the workplace environment. BACKGROUND Measuring underground coal mine dust concentrations is an essential part of protecting miners' health. The U.S. Secretary of Labor and the Federal Advisory Committee on the Elimination of Pneumoconiosis among Coal Mine Workers has recommended that better monitoring of coal miner dust exposures be used as a method to improve miner health. In consultation with labor, industry, and government, NIOSH issued a contract to Rupprecht & Patashnick Co., Inc. (R&P), Albany, N.Y., to develop a one-piece PDM. The object was to miniaturize TEOM technology into a form suitable for a person-wearable monitor that would enable accurate end-of-shift dust exposure information to be available to miners. Furthermore, any person-wearable dust monitor should minimize the burden to the wearer by incorporating the monitor into the mine worker's cap lamp battery, with exposure data continually displayed during the shift to enable workers and management to react to changes in dust exposure. In the summer of 2003, NIOSH conducted extensive testing of the PDM to determine its laboratory and in mine performance. In addition, anecdotal information collected in the mines showed several occasions where miners were able to identify situations that produced high levels of respirable coal mine dust The PDM's response to unplanned changes resulted in action being taken to keep dust exposures as low as possible. In another case that demonstrated the PDM's versatility, a mine was seeking to find a better dust control solution on its longwall headgate stageloader. In this instance, the PDM was used as a diagnostic tool by the miners to quickly evaluate the control technology. [ ] HOW DOES THE PDM WORK? The PDM is configured to provide accurate respirable dust personal exposure information in a form that is as convenient to wear as a normal cap lamp (See Figure 1). Respirable dust exposure data displayed by the device has two main objectives: providing the miner and mine operator with timely values to avoid overexposure to dust, allowing them to make any necessary changes during the course of a work shift; and computing an accurate end-of-shift statistic for a miner's average respirable dust exposure. The mass sensor embedded in the PDM, holds the key to the accurate, time-resolved dust concentration measurements. The inertial, gravimetric-equivalent, mass measurement technique used in the device typically provides a limit of detection on par with that of the most sensitive laboratory-based microbalances.

By Kihong Park, Matthews C. Habjan, Arthur L. Miller

New Mining Safety and Health Administration (MSHA) regulations limit the mass concentration of airborne diesel particulate matter (DPM) or, more specifically, the concentration of elemental carbon (EC), in underground mines. The mine operators are responding by introducing a variety of controls to reduce DPM in the mines, potentially including the evaluation of new maintenance procedures to reduce underground mine vehicle emissions. There is currently a lack of an inexpensive and dependable method to directly measure the DPM concentration emitted from the vehicle tailpipe. To that end, this work demonstrated a simple field portable method for estimating the mass concentration of elemental carbon exiting the tailpipe of a diesel engine using a direct reading photometer. Simultaneous measurements of tailpipe exhaust were made with a Thermo Electron Personal DataRAM 1200 photometer (particulate mass concentration based on light scattering) and by analyzing PM2.5 and PM1.0 samples collected on quartz fiber filters using the National Institute of Occupational Safety and Health (NIOSH) method 5040 (mass concentration of EC via thermal-optical method). Results indicate surprisingly good correlation (R2 ) 0.97) of the two methods when the data are adjusted for relative humidity (RH) and corrected using an empirically generated calibration factor. Although preliminary, it may be possible to implement this method in maintenance shops to monitor emission trends and to compare emissions of various vehicles in a fleet. Such data will be useful for fleet planning to meet new air quality standards.

By Gerald T. Homce, James C. Cawley

Arc flash generally refers to the dangerous exposure to thermal energy released by an arcing fault on an electrical power system, and in recent years, arc flash hazards have become a prominent safety issue in many industries. This problem however, has not been effectively addressed in the mining industry. MSHA data for the period 1990 through 2001 attributes 836 injuries to “non-contact electric arc burns”, making it the most common cause of electrical injury in mining. This paper presents results from several elements of a recent NIOSH study of arc flash hazards in mining, and provides information and recommendations that can help reduce these injuries. Characteristics of past arc flash injuries in mining are first outlined, such as the electrical components and work activities involved (based on MSHA data). This is followed by a review of important concepts and terminology needed to understand this hazard. Next, methods for identifying, measuring, and managing arc flash hazards on a power system are covered, with emphasis on recommendations found in NFPA 70E, Standard for Electrical Safety in the Workplace. Finally, results are presented from a detailed arc flash hazard analysis performed on a sample mine electrical power system using IEEE 1584-2004a, focusing on components and locations presenting severe hazards as well as engineering solutions for reducing the risk to personnel. Index terms – electrical arcing, electrical burns, mining, arc flash hazard analysis

To provide operators of large-opening mines with a ventilation planning tool that will help them develop a healthier, safer, and more efficient ventilation system in the underground workplace.

Jan 3, 2006

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state-of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-term underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results froman extensive series of Schmidt Hammer tests found that the shotcrete increased in strength by 70% during the humid summer months.

By F. W. Lee

The paramount importance of water to life of all forms on the earth is too well known to require elaboration in this brief paper. It has repeatedly been termed the most valuable of all our mineral resources. Its importance is justifiably recognized in the extensive areas covering the earth which receive sufficient rainfall to sustain a relatively luxuriant vegetation; but in those areas where rainfall is insufficient to support anything but a relatively meager plant growth, the location of a water supply and its development become of even more vital interest to those attempting to obtain a living from the soil. Geological investigations concerning the water supply of the United States have been most extensive, important work having been accomplished by Federal, State, and local governments and by private enterprise. A casual examination of the titles of the 739 Water-Supply Papers published by the United States Geological Survey3/ alone testifies 'to the vital nature of our water resources and the extensive work that has been done on them.

Jan 1, 1936