Search Documents

By John L. Miller

The synthetic fluormicas may be divided on the basis of silicon content into tetrasilicic, trisilicic, and disilicic. Properties of lead and barium disilicic fluormicas were determined to characterize these two representative members of the disilicic group. Properties described include unit-cell parameters from X-ray diffraction, optical data, chemical composition, density, melting point, and mechanical and dielectric properties. Both the lead and the barium micas were typically monoclinic; neither was sufficiently cleavable to yield usable mica splittings. Both yielded polycrystalline, machinable ceramics with excellent mechanical and dielectric properties.

Jan 1, 1963

By E. L. McHugh, R. T. Mayerle, J. M. Girard

Ground control problems at surface mining operations can occur for a variety of reasons. Stress, gravity loading, rock strength, geology, pore pressure, weather effects, underground workings, and many other factors contribute to slope instabilities that range from small rock falls to massive slides of material. While some of these failures can be predicted or controlled by preventive measures, each year many completely unexpected failures occur. Current methods for monitoring generally involve measuring displacements at a few, selected points in and around the suspected area of instability. While most of the displacements along these points will be in a downslope direction, freeze-thaw cycles of water-filled joints, horizontal stresses or pressure, buoyancy in saturated soils, human measurement errors, or other situations can produce deformation in almost any direction, even without any instability in the slope. Determination of which, if any of the observed movements represents a potential hazard is essential. Because of the enormous surface area of many large open-pit mines, several varieties and scales of instability can occur. Small, unexpected rock falls may indeed be more hazardous than a massive failure that involves slow displacement of material over a longer period of time. Complete vigilance to detect all small potential falling blocks is neither feasible nor economical and certainly is not attainable using today's most common point displacement monitoring techniques. As part of an on-going study at the Spokane Research Laboratory, several new methods for monitoring slope instabilities are being investigated. This paper describes the potential adaptation of systems such as interferometric synthetic aperture radar, imaging spectroscopy, and time-domain reflectometry, to slope monitoring and design.

By Don M. Coulter

"INTRODUCTION The Margerum bauxite district, in Colbert County, Ala. was investigated in December 1940 and in February 1943 by R. W. Smith of the Bureau of Mines .3/ A geologist of the Federal Geological Survey investigated and mapped the district in the fall of 1942.These preliminary investigations indicated bauxite showings over an area about a mile long by 2,000 feet wide. It was felt that the chances were good for finding one or more large deposits of low- to medium-grade bauxite. The location - within 35 miles of the alumina plant of the Reynolds Metals Co. atLister Hill, Ala. – made it especially attractive. A field office was established in Iuka, Miss., on May 19, 190,, and mineral agreements were executed with four landowners covering 1,146.6 cores.The drilling on the project was done under contract. The power drilling was supplemented by a labor crew that drilled hand-auger holes, where there was little or no gravel overburden, and sampled the old test pits.The Federal Geological Survey, after thorough study of the district, recommended 54 drill holes 4/ to delimit the known deposits and to search for possible extensions. After the drilling started, many of these locations eliminated, and others were changed upon the basis of information gathered from the holes as they were drilled."

Mar 1, 1948

By V. F. Parry

The object of this report is to present certain pertinent data on the physical and chemical properties of South Arcot lignite and to present the results of several special tests to show how the raw lignite can be upgraded to superior fuels for certain special uses. The Bureau of Mines Branch of Coal Technology laboratories at Denver have advocated the drying and carbonization of all low-rank fuels for special uses and have introduced and developed new techniques for upgrading and refining noncoking coals. Application of these techniques to the South Arcot lignites was the object of the investigation, and this report presents significant data necessary for planning a fuel program based on utilization of dried and carbonized dusts. In general, the South Arcot lignite is similar in chemical properties to the high-moisture lignites found in the United States and has some physical properties similar to Australian brown coals. The samples submitted for test had lost moisture before delivery to the laboratory, and it has been necessary to estimate the analysis of the lignite in place in the mine. Various observations made in India by qualified technicians indicate that the bed moisture content of the entire seam is in the range of 54 to 56 percent. For estimating purposes in this report, the bed moisture content has been taken as 56 percent and the ash content of the fresh coal as 2.5 percent. The average analysis estimated for the as-mined lignite is: [Moisture percent 56.0 Volatile matter do.22.0 Fixed carbon do.19.5 Ash do.2.5 Heating value B.t.u. per lb. 4,890]

Jan 1, 1957

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

By R. E. Head

[Recent investigations at the Intermountain Experiment Station of the Bureau of Mines at Salt Lake City indicate that metallurgists have given little attention to the occurrence of jarosite minerals in the oxidized ores of lead and silver. These investigations have also emphasized the importance of lowing when these minerals occur in the oxidized ores, especially those containing lead, silver, and gold, as their presence is a material factor in selecting a suitable kind of treatment. Since the question of the occurrence of jarosites in oxidized ores has come to the attention of the Bureau of Mines, investigation has indicated that plumbojarosite and argentojarosite are quite common. These two minerals appear to be widely distributed and probably escaped recognition by persons who had attempted to treat certain oxidized lead ores in which the jarosite minerals represented a material portion of the metal content. Consideration of the physical characteristics of the jarosites also indicates that in many cases failure to treat some of the oxidized lead ores with success has been directly due to the fact that the greater portion of their lead and silver content was present as plumbojarosite and argentojarosite. The data and the description of these minerals given in the body of this paper indicate that attempts to recover lead and silver from ores in which appreciable amounts of too metals occur is plumbojarosite and. argentojarosite would be unsuccessful if confined to gravity methods of concentration. There are undoubtedly considerable tonnage of oxidize lead ores in the various mining regions of this and other countries, and it is quite probable tat in some of these ores the metal content of lead and silver may be largely anglesite (lead sulphate) and cerussite (lead carbonate) but that they will also contain cerargyrite (silver chloride), argentojarosite, and plumbojarosite. The treatment of such ores therefore presents an important problem, since a product is discarded from]

Jan 1, 1928

By Allen S. Smith

Analysis of the helium content of a natural gas presents more than the usual difficulties encountered in applying the thermal--conductivity method because of the relatively small amounts of this inert gas present and the wide variation in the other constituents. However, the numerous advantages of this method and its adaptability to continuously recording and control instruments make it worthy of consideration. A specific application of the method described yields quantitative results only when used with gas mixtures of known qualitative compositions which vary within predetermined limits. Periodic analyses for the helium content of a producing gas well may be conveniently made by an absorption method3/ and a continuous analytical method is not necessary for this purpose. Natural gas containing 1.75 to 1.90 percent of helium produced from Government-owned wells is processed in the Amarillo (Texas) Helium Plant of the Bureau of Mines. The helium extracted in the plant is supplied to the Army and Navy, and the processed natural gas is sold to a commercial gas company4/. As complete recovery of the helium in the raw material is not economically practicable, the processed gas contains 0.1 to 0.3 percent of helium, depending upon conditions of operation;- Production is checked against the helium removed from the gas, which before the installation of the thermal--conductivity apparatus was calculated from the analysis of a cumulative sample of the processed gas. As conditions of operation affect the residual helium content to a large extent, a composite sample was an uncertain index of the efficiency of the process.

Jan 1, 1934

By Terry R. Neumann

A mineral survey of the 23,760-acre Abert Rim Wilderness Study Area (OR-1-101) was conducted by the U.S. Bureau of Mines in 1986 at the request of the Bureau of land Management in order to evaluate its identified mineral resources. The study area is located in south-central Oregon, 26 mi north-northeast of Lakeview, OR. Federal and Lake County mining records indicate no mining claims, geothermal leases, or oil and gas leases within the study area as of January 1, 1987. No economic concentrations of minerals were found in the study area. The Wilderness Study Area is dominated by Abert Rim, a north-trending Basin and Range fault scarp that parallels the study area's western boundary. Exposed on the scarp is an approximately 2,000-ft-thick volcanic sequence consisting of Oligocene-Miocene basalts, tuffs, and tuffaceous sedimentary rocks.

Jan 1, 1987

By George A. Page, Hewitt Wilson, Vance S. Cartwright

"Purpose of InvestigationThe process of removing solid material from liquid suspensions has been studied at the Northwest Experiment Station, United States Bureau of Mines, in cooperation with the University of Washington, as part of a general program to investigate the dewatering of Pacific Northwest plastic kaolins, which is difficult by ordinary filter-pressing methods. The present paper is a progress report of the work began by Vance S. Cartwright in 1928 and continued in 1931 and 1932. Spray evaporation is believed to be valuable for the following classes or grades of clay and clay mixtures:(1) Highly colloidal, plastic-type clays, which release their mechanically attached water with difficulty; (2) clays prepared for shipment in pulverized or powdered condition; and (3) synthetic, ceramic, porcelain, and tile mixtures prepared as aqueons suspension, dried and pulverized before molding. Dilute suspensions can be dewatered by spray evaporation to produce concen-trated casting slip or plastic clay with a lower water content.The most common dewatering method used in preparing powdered kaolin for the market comprises the following steps: Reduction of the water content by filter-pressing from approximately 75 percent in the thick ""slip"" condition to about 30 percent in the condition; further reduction of the water in the filter-press cakes by heat to about 5 percent; and pulverization of the dried cakes in hammer or dust. These three steps can be simplified to a single process by spray evaporation."

Jan 1, 1935

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of materials used in the construction of mine stoppings and in the sealing and reinforcing of mine ribs and roofs. The materials investigated were: silicone, phenolic, and isocyanate-based rigid foams, as well as epoxy and acrylate mine sealants. Of the rigid foams tested, the X-156 urethane foam presented the greatest toxic hazard based on toxic load values hydrogen chloride was the main toxic species evolved by this foam. In 'lone of the isocyanate-based compositions was hydrogen cyanide the major component, but its contribution increased with temperature. The FS-24 urethane and Celotex Max-Seal isocyanurate foams had the lowest toxic load values, although these two foams have different applications for in-mine use. Of the two mine sealants tested, the latex /acrylic coating presented the greater toxic hazard with acetic acid being the main toxic species evolved.

Jan 1, 1983

By Robert F. Chaiken

An absorption-desorption model of particle reactivity was employed to describe the observed relationship between two apparently diverse phenomena which have been the subject of considerable study at the U.S. Bureau of Mines: (1) coal-rock dust reflectance and (2) coal-rock dust explosibility. The model accounts for heterogeneities in particle-size and material properties; however, in the present report, only particle-size distribution is considered. A mean particle-size parameter, appropriate to the explosion extinction process, is derived, and then taken as appropriate to describing optical reflectance. The derived form-to-function relationships for the two processes, when compared with experimental data, suggest that a problem exists with previously derived theory relating optical reflectance to rock dust concentration. A reexamination of that theory leads to a new theoretical expression, changed by a factor of 2, for the variation of rock dust concentration with reflectance which is in quite good agreement with experimental results. The current work offers justification for measuring and establishing rock dust requirements for specific coal dust size distribution(s) found in the mine-distributions that undoubtedly depend on the mining method and the type of coalbed.

Jan 1, 2010

By H. E. Powell

The magnetic susceptibility, the geographical source, and associated minerals are given for 44 copper-, 26 lead-, and 19 zinc-bearing minerals. Of the 44 copper minerals/ all had a susceptibility of less than 15 X 10-6 cgs, and about 20 percent of them were diamagnetic. Of the 26 lead minerals, all had a susceptibility of less than 11 X 10-5 cgs, and almost half of them were diamagnetic. And, of the 19 zinc minerals, all except four had a susceptibility of less than 9 X 10-6 cgs, and about one-fourth of them were diamagnetic.

Jan 1, 1968

By Robert P. Vinson

This Bureau of Mines report presents the results of tracer gas studies conducted at three facilities where bagger hoods had been installed several years ago to remove airborne silica dust from the vicinity of the bagging operator. The studies indicated that for optimum benefits makeup air must be evenly dispersed, the hood enclosures and duct systems must be as airtight as possible, the average intake air velocity of each hood should be at least 200 fpm, and the hoods and duct systems must be properly maintained.

Jan 1, 1981

The Bureau of Mines in the Department of the Interior is increasingly concerned with the safety and health of personnel engaged in coal-mining operations, particularly below ground. The Bureau is also concerned with improving the utilization of domestic mineral resources, and reducing the environmental impact of mineral operations. One obvious way to improve safety and minimize health hazards would be to eliminate coal mining entirely by bringing the energy value of the coal to the surface in some other way, such as by partially burning it underground to form combustible gases and bringing these gases to the surface, where their energy content can be put to use. This technique might also improve the utilization of the coal resource. ? Accordingly, the Bureau of Mines, interested in re-evaluating underground coal gasification technology in terms of current and expected conditions in the United States, requested Arthur D. Little, Inc., (ADL) to appraise the technology to determine: ? Whether the current (1971) state of the technology offers a technically feasible method for gasifying coal underground that is applicable to the reserves of bituminous and lower rank coals in the United States. ? Whether a program of research and further development of the technology could ultimately make it a technically feasible alternative to current open-pit and underground coal mining operations. ? What the nature and cost of further research and development work in the technology should be.

Jan 1, 1971

By F. B. Tough, B. H. Scott

"Petroleum engineering is a comparatively new branch of engineering, with which few people, even petroleum operators and mining engineers, are thoroughly familiar. Petroleum engineers are responsible for the accurate keeping of well logs and all pertinent data upon formations encountered, for the careful analysis of such information, and recommendations as to most suitable places for drilling, for detailed study of methods of drilling, casing, and so on in order to obtain maximum production for a minimum cost.The Bureau of Hines has from time to time carried on work in all branches of petroleum engineering in the various fields of the United States. Such work is also being carried on extensively by the California State Mining Bureau, which has in its employ a number of men who have had, besides their technical training, actual experience in oil field work. This is about the only state at the present time which is carrying on this work in a definite way. It has therefore been the practice of the employees of the Bureau of Mines to go to other states and give such advice and assistance as might prove of value in development work and in prolonging the production of the fields."

Jan 1, 1920

By James Ridenour

The Gearhart Mountain Wilderness and RARE II area 6225 encompass 22,823 acres (9,236 ha) of the Fremont National Forest in southern Oregon (fig. 1). The area was studied under the provisions of the Wilderness Act of 1964 (Public Law 88-577). The U.S. Bureau of Mines determined the mineral potential of known mines, prospects, or mineralized areas, while in a separate effort the U.S. Geological Survey made geological, geochemical, and geophysical studies. MINERALIZED AREAS The study area contains no mining districts or known claims. Nearby occurrences of uranium, base metals, perlite, mercury, and diatomite apparently do not extend into the study area. Reconnaissance pan samples reveal only trace amounts of gold. No anomalous economic minerals were found in heavy mineral fractions of samples from stream beds draining the area.

Jan 1, 1982

By Christopher Mark

The first International Conference on Ground Control in Mining opened with the topic of pillar design. Two classic papers were presented, one by Bieniwski and the other by Wilson. Unfortunately, the two methods were so radically different from each other that it was nearly impossible to reconcile them. Adding to the confusion were the many other pillar strength formulas (such as the Salamon-Munro, the Holland-Gaddy, and the Obert-Duvall, just to name a few) that were also available. Little wonder that discussions of pillar design in those days often ended with anguished cries of “but which formula is the right one?” The past 25 years have seen substantial progress in the science of coal pillar design. Indeed, one testament to the improvement is the relative scarcity of papers on the topic at recent Conferences. Two factors have been largely responsible for the progress that has been made. The first has been the collection of large data bases of actual case histories of pillar performance in a variety of settings, from shallow room-and-pillar mines through deep cover longwalls. These have made possible the development of empirical design procedures that are closely linked to real world experience. The second important factor is the development of sophisticated computer models that can accurately simulate pillar behavior and roof/pillar/floor interactions. Together, these two lines of research have led to a new understanding of pillar mechanics that identifies three modes of pillar failure: • Sudden, massive collapse, accompanied by airblast, for slender pillars (width/height<4) • Squeezing, or slow, non-violent failure, for most room and pillar applications (4<w/h<10) • Entry failure or bumps for deep cover and longwall applications (w/h>10) It is particularly satisfying that the insights gained from numerical models broadly support those obtained from the empirical studies. While far less controversial than in the past, pillar design problems continue to arise. One recent example is pillar design for highwall mining. NIOSH has just released a software package, called ARMPS-HWM, which employs a number of modern pillar design concepts. Since highwall mining web pillars are long and slender, the greatest danger is that of a sudden collapse. ARMPS-HWM suggests two possible prevention strategies, one which

By Eugene T. Sheridan

The 22d annual survey of the packaged-fuel industry by the Bureau of Mines, United States Department of the Interior, revealed that 26 plants in 8 States were in operation and reported production in 1956. The demand for packaged fuel in the United States has declined gradually since the end of World War II, and the number of operating plants has decreased from 70 in 1946 to 26 in 1956. Annual productive capacity of the industry has decreased also during this period, and the decrease in capacity was about proportional to the decrease in operating plants. Packaged-fuel plants are relatively small, and 85 percent of the active plants in 1956 had an annual capacity of less than 10,000 tons. The same situation prevailed in 1946, when 84 percent of the plants had a capacity of less than 10,000 tons. Total capacity for the 26 active plants in 1956 was 174,600 tons, an average of 6,715 tons per plant. Operating rates in 1956 were the highest since 1951, and the rate of production for the industry averaged 37 percent of capacity.

Jan 1, 1958

By W. P. Yant

This report describes result of a study of the carbon monoxide and particulate matter in the air of the Holland, Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development

Jan 1, 1941

By William C. Miller

This report describes investigations by the Bureau of Mines designed to establish the noise level and spectrum of various types of pneumatic rock drills and to furnish information that would be useful in conducting sound measurements in mining environments and in reducing the noise generated in pneumatic drilling. These investigations show that (1) the noise generated by the drills in the frequencies below 100 cps is caused by the impact of the piston and drill steel, in the frequency range between 100 and 2,000 cps by the exhausting of air from the ports, and in the frequencies above 2,000 cps by the resonant frequencies of steel drill parts and of drill steel; (2) satisfactory instruments and instrumentation systems are available for field and laboratory measurements; (3) reliable sound measurements can be made in mining environments; and (4) devices can be developed that will abate the noise.

Jan 1, 1963