Search Documents

By K. K. Kelley

"INTRODUCTION The Bureau of Mines nitrogen peroxide process (2) 3/ for extracting manganese from low-grade ores is essentially a two-stage process involving the reversible reactionMnO2 + 2NO2 + 6H2O = Mn (NO3)2 . 6H2O (1).At lower temperatures this reaction proceeds to the rigth and affords a means of dissolving manganece and separating it from unreacted ore. At higher temperatures the reaction proceeds to the left and manganese dioxide is recovered and nitrogen peroxide regenerated for recycling. Evidently, therefore, the energy required for decomposition of manganous nitrate is a matter of practical importance. Similar information for certain other nitrates also is desirable beceuse the nitration step of the process produces appreciable amounts of nitrates of other metals, such as iron, aluminum, magnesium, calcium, and barium, some of which are not broken down in the evaporation and decomposition steps. Thus, a portion of the nitrogen peroxide is not directly available for recycling. Whether or not it is feasible to recover nitrogen peroxide locked in the more-stable nitrates depends partly on the energy required and the conditions necessary for their decomposition.To supply information bearing directly on these subjects, several researches were undertaken at the Pacific Experiment Station: (a) Heats of formation (24, 25, 26) of nitrates of manganese, magnesium, calcium, barium, and aluminum were measured at 298.2° K:; (b) low-temperature specific heats (23), in the range 51° to 298.2° K,, and entropies of nitrates of magnesium, calcium, barium, and aluminumm were determined; and (c) heat contents (21) above 298.2° K. of the nitrates of manganese, magnesium, calcium., and barium were measured. The results of these studies, when correlated by thermodymamic methods, permit evaluation, at any temperature of interest, of the energies required to decomposethe nitrates and furnish information concerning the equilibrium pressure temperature relationships."

Sep 1, 1944

By Juh W. Chen

A process for recovery of energy from waste coal fines was investigated. The process, which was developed through laboratory, bench, and pilot plant scale experiments, consists of mechanical cleaning followed by high temperature oil agglomeration and pelletization. The process can produce a quality product under an economically and environmentally acceptable condition. Waste coal fines with ash less than 35: and HHV greater than 6,000 BTU/1b have been upgraded to a product with less than 15% ash and HHV Greater than 11,500 BTU/lb. A computer model has been developed to optimize the processing costs and to perform economic evaluation of specific sites. Ultimately tine model can be utilized to establish a priority listing for a region in assisting the determination of reclamation strategy.

Jan 1, 1983

By George C. Branner

This circular is concerned with eight nonferrous scrap metals as they generated, collected, prepared, and consumed in California. Brief reference also is included with respect to Nevada and Hawaii. Four of these scrap metals - copper, lead, aluminum, and zinc - are of major importance and make up about 95 percent of the total value, whereas the remaining four - antimony, magnesium, nickel, and tin - make up the remaining 5 percent. For convenience, the subject matter is divided into three parts, (1) Data with respect to the collection, preparation, and marketing practices that are common activities to all the nonferrous scrap metals; (2) separate discussions and statistical data with respect to each of the eight nonferrous scrap metals in California; and (3) data with respect to Nevada and Hawaii.

Jan 1, 1962

By P. D. Lohn

The objective of this program was to develop nozzle designs to maximize the effective cutting length of a water jet. The results of the theoretical program directly support the Bureau of Mines Borehole Mining Program and their experimental program to improve the rock cutting capability of water jets. The borehole geometry requires turning the flow by 90 degrees and accelerating through the nozzle within a restricted length. Several suggestions for turning the flow are offered. The borehole space limitations constrain nozzle length, to the extent that a standard 13-degree tapered nozzle (6-1/2 degrees half angle) is too long to fit in the borehole, at production flow conditions. The design technique developed is computationally economical and enables examination of a large number of shapes and flow conditions. The nozzle design is based on design criteria of minimization of boundary layer thickness at the nozzle exit and minimization of the possibility of separation and cavitation. Six flow conditions, including pressures to 4500 psi and flow rates to 400 gpm, were examined, Best shapes were determined for all flow conditions. The best shape for a borehole reining application consists of an initial 4th degree polynominal (quartic) at the entrance followed by a straight section with a twenty degree (half-angle) taper at the exit.

Jan 1, 1976

By John M. Gomes

The preparation of tungsten carbide by molten-salt electrolysis was investigated. Sodium tungstate in the electrolyte and carbon from the graphite anode were the source materials, Optimum results were obtained with an electrolyte consisting of 83 mole-percent sodium chloride and 5.7 mole-percent each of sodium tungstate, sodium metaborate, and sodium hydroxide; a temperature of 1,000° to 1,025° C; an anode current density of 37 amp/dm2 or less; and an initial cathode current density of 150 amp/dm2. The yield was approximately 0.45 g/amp hr. The electrolytic tungsten carbide product contained approximately 5.4 weight-percent combined carbon as compared to 6.1 weight-percent for pure tungsten carbide. Microhardness of the electrolytic tungsten carbide, determined with a 50-gram load, varied from 3,480 to 3,970 dph. The material was friable and could be ground in a laboratory ball mill to less than 400-mesh particle size.

Jan 1, 1969

By J. J. Demeter

Experiments were conducted in 2- and 4-inch-diameter standpipes to evaluate the effectiveness of standpipes as pressure seals. During the experiments, these standpipes conveyed Alan-Wood magnetite (60 to 230 U.S. standard sieve mesh) by gravity flow from one vessel to another of relatively higher pressure. The information obtained has been helpful in a Federal Bureau of Mines investigation of how to make either synthesis gas or hydrogen by a modified steam-iron process employing a continuous recycling stream of granular iron-iron oxide at temperatures of 600° to 900° C. In this process the mixture of granular material flows by gravity from a reduction vessel at low pressures to an oxidation vessel at higher pressures. Data from the 2- and 4-inch-diameter standpipes indicate that it would be practical to use a standpipe as a pressure seal between the reductor and oxidizer. Investigators found that, by gravity flow, the standpipe could convey the Alan-Wood magnetite against pressure gradients up to 1.07 pounds per square inch per foot of column height.

Jan 1, 1961

By N. S. Dalal, X. Shi

"It has been recently suggested that the exceptionally high antitumor and antibacterial activity of natural fredericamycin A (FMA) is related to its ability to spontaneously generate the superoxide anion (02-) and hydroxyl (""OH) radicals in aerobic solutions [Hilton, B. D., Misra, R., & Zweier, J. L. (1986) Biochemistry 25, 5533]. With a view to understand the mechanistic details, attempts were made to reproduce earlier electron spin resonance (ESR) evidence for the oxygenated free radical formation in well-aerated solutions of natural FMA in dimethyl sulfoxide and dilute H 20 2• Little or no evidence was obtained for the formation of the 0 2- and methoxy (""OCH3) radicals, while the detected formation of the 'OH and methyl ('CH3) radicals was attributable largely to mechanisms not involving FMA. These results thus reopen the T question regarding the mechanism of its exceptionally high tumoricidal-bacteriocidal activity. This paper reports on an electron spin resonance (ESR) investigation of the formation of oxygenated free radicals in solutions of natural fredericamycin A (abbreviated as FMA) which has recently been reported to be a highly potent anti¬tumor antibiotic (Pandey et al., 1981; Warnick-Pickle et al., 1981). The impetus for this undertaking was provided by recent reports (Hilton et al., 1986; Stinson, 1986) suggesting that the strong tumoricidal activity with high therapeutic—toxic index of FMA was related to its ability for the spontaneous generation of superoxide anion (02-) and hydroxyl (OH) radicals. For example, the suggested mechanism for the formation of 02- by FMA was (Hilton et al., 1986)FMA-OH + O2 FMA-O + H+ + 02-Here FMA—OH is simply the FMA molecule emphasizing the —OH moiety which becomes FMA-O, the free radical rep¬resenting the oxidized form of the drug. While some other highly effective anticancer drugs in current clinical application, such as bleomycin, are also thought to exert their antitumor effects via the formation of reactive drug-based or oxygenated free radicals (Carmichael et al., 1985; Gianni et al., 1983), FMA was considered unique in that only in this case the free radical formation was thought to be spontaneous, rather than through a metal- or an enzyme-activated process (Hilton et al., 1986; Stinson, 1986). Thus it was suggested (Hilton et al., 1986; Stinson, 1986) that FMA could be the forerunner of a new class of anticancer drugs. However, we noted that while the hypothesis seemed plausible, the reported ESR spectral evidence appeared to be ambiguous. Because of the high significance of the earlier conclusions (Stinson, 1986), we undertook a systematic ESR study of the radical formation in FMA solutions, and as discussed below, our conclusions disagree with those reported earlier."

Jan 1, 1989

By Robert J. Timko

In early June 1986, an underground fire of unknown origin erupted in one of several entries of a coal mine located in southwestern Colorado. For a time, mine personnel aggressively fought the fire. However, control of the fire was later lost. To prevent further damage and reduce the possibility of an explosion, all portals and shafts to the mine were sealed. The mine operator requested the U.S. Bureau of Mines' assistance in obtaining and analyzing mine fire gases taken from sampling ports placed through the mine seals, as well as down boreholes drilled after the fire. This report recounts activities within the first 2 years of the mine being sealed. It includes a description of gases analyzed and mine atmosphere status equations generated from the analyzed gases. The gases were analyzed by chromatography and included standard atmospheric gases as well as higher hydrocarbons that are found in postfire atmospheres. Nine equations were used to evaluate what was occurring within the sealed mine. Following a description of the rationale behind each equation, the 2-year trend is briefly analyzed.

Jan 1, 2010

By R. A. Beall, W. E. Anable

The purification of hafnium by electron- beam melting at moderate energy inputs and at low pressures was examined in detail . Most metallic impurities and hydrogen were removed in the first few minutes of operation ; oxygen , carbon , and nitrogen were removed at a slower rate . Samples treated by electron bombardment suffered a small loss of weight and a gradual lowering of hardness . The magnitude of each change varied with the energy input and the duration of the melt . Analysis of the data confirms the loss of oxygen as a hafnium monoxide . Approximate activity coefficients for other contaminants are given .

Jan 1, 1964

Low-cost housing, like automobiles, should be appraised in the light not merely of first cost but of upkeep as well. Even more important than the number of miles the family car will go on a gallon of gasoline is the number of days the family home can be kept comfortable on a ton of fuel. A furnace tender who tossed every third shovelful of coal into the ashcan would lose his job promptly, but the effect is the same when homes continue year after year to pour out precious heat through uninsulated roofs and walls, Greater economy in household heating means even more to the national economy than to the individual, especially now that we are preparing for defense. Our fuel resources, although large, should be conserved. If less fuel is used for civilian needs, augmented requirements for defense can be met without unduly increasing the number of men needed at the coal mines and oil ells or adding new producing units that might complicate ultimate readjustment to peacetime conditions when the emergency is past and over-expansion of many industries brings new problems if unnecessary demands for transportation facilities are reduced, public carriers will be able to haul more munitions, and manpower needed for national defense will be released; and by protecting workers from health hazards in their homes additional man-hours of productive effort will be gained. Moreover, reducing the running expenses of houses by proper heat insulation helps home owners to maintain payments on property, and by minimizing foreclosures helps to stabilize the financial structure of the country. In short, here is a situation where the interests of the individual and the Nation are identical and the greatest good for the greatest number is obtained without sacrifice to anyone.

Jan 1, 1941

By W. E. Pittman

The Bureau of Mines, as part of its Health and Safety Technology Program, is conducting research on the use of ground penetrating radar (GPR) for mine hazard detection. GPR offers a possibility of mapping immediate below-surface geologic conditions, including faulting and other anomalies, thereby exposing potential safety hazards to miners. This report summarizes a literature review of the current status of GPR research in and outside the Bureau.

Jan 1, 1984

By T. T. Read, F. C. Houghten

"The bad effects upon the health and output of miners that result when the ventilating current in a mine lacks sufficient cooling power have been described by Harrington and Sayers in a previous report (1)*** The normal temperature of the human body is about 98.5°F. and whenever work is done by the muscles, indeed even when sitting still, the normal bodily processes generate heat which must be given off, otherwise the body will become overheated and a number of bad effects will be produced. If it were possible to so enclose a man that he could continue to breathe and no heat could escape from his body he would die within a short time. In a series of experiments made at the Pittsburgh Station of the Bureau of McConnell and Houghton (2) found that a dry-bulb and a wet-bulb temperature of 112.5°F could he borne for only 35 minutes, even when the subject was at rest. A wet-bulb temperature of 100.4°F (dry-bulb 157°F) could only be tolerated for 45°F minute. Under such conditions the bodily temperature rises as much as 45°F above normal and the pulse is accelerated. Very uncomfortable sensations are felt when the pulse rate exceeds 135. The human body, like any other internal combustion engine, must be cooled in order to function properly.Under ordinary circumstances the air surroundings people is enough coder than themselves to permit this heat generated within the boiy to be river off with¬out difficulty. At higher temperatures, or when the rate of work, with its corresponding generation of heat is high, the body can not throw off heat fast enough, so it begins to sweat and the evaporation of the sweat cools the body. But the results of the experiments cited above indicate that in still air, even with the body at rent, it can not adjust its temperature when the air is above 90° wet- bulb. J. S. Haldane (4) says ""at a wet-bulb temperature of 60°F the actual amount of work done by the miner begins to fall off; as the wet bulb temperature rinse farther the work Bona gradually diminishes to the vanishing point. Then the temperatures indicated by the wet-bulb exceeds 85°F hard work in a mine seems hardly or the commercial working of a mine the wet-bulb thermometer should not in generaI, be allowed to rise above 80°F, unless perhaps where there it a good current."

Dec 1, 1923

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

By L. W. Brandt

The Bureau of Mines, as part of its mission to effect pollution abatement, conducted research to study various means of dewatering Florida phosphatic clay wastes and reclaiming mined lands. The work was done in cooperation with 10 Florida phosphate companies. During this work, a novel technique to effectively dewater phosphatic clay wastes was developed. The solids contained in the clay waste slurry are slowly compressed by moving wire mesh screens through the system. In a typical application, the screens were moved downward, compressing solids ahead of the screens. The rate of movement of the screens is an important variable in the process. It is believed that the moving screens distort the gel structure of the phosphatic clay system and cause the release of water. Samples of 18 clay wastes, including a high-grade attapulgite from beneficiation plants of the Florida phosphate field, were studied using the method. Typical samples were concentrated from initial solids of 4.7 and 11.9 percent to 16.8 and 25.2 percent, respectively, in 3-1/2 days. The high-grade attapulgite sample was dewatered from 2.7 percent solids to 13 percent solids in the same period.

Jan 1, 1980

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By G. W. Jones

In a previous report,6 results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.l cubic feet when the number of ventilation openings in the cover was varied. from no openings to a maximum of 48. The results showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

By E. C. Lane

This paper is the first putt of a report giving the results of the Bureau of Mines' twenty-third semiannual survey of motor gasoline marketed in the United States. A companion report, Part II, is in preparation and will give a more detailed discussion of the whole survey. Results of the determination of copper-strip corrosion, color, sulphur content, copper-dish evaporation residue, and gum content as given by the Bureau of Mines steam-oven method will be presented in the second paper, which will also include the prevailing retail price and the tax at the time the sample was taken. This paper deals specifically with data relative to gravity, Reid vapor pressure,' and distillation (method 100.13).6 The samples tested were divided into "competitive-price gasolines" and "premium-price motor fuels," a method of presentation that was begun with the twenty-second semiannual survey. A total of 312 samples were collected from service station pumps in 20 cities throughout the United States. Of this number of samples, 207 were "com-petitive-price gasolines" and 106 were "premium-price motor fuels." All of the samples were collected in March, 1931, and analyzed at the Petroleum Experiment Station of the United States Bureau of Mines at Bartlesville, Okla. "Competitive-price gasoline" includes those fuels that are sold at the generally recognized local base price and all fuels that are sold below that price. All fuels that are sold at an advance over the generally recognized base price are placed in the class of "premium-price motor fuels." These fuels include Ethyl gasolines, benzol blends, "high-test" fuels, and those fuels that owe their "anti-knock" rating to the process of manufacture rather than to the addition of other material such as Ethyl fluid or benzol. The term "high-test" is generally applied to motor fuels that are more volatile than the regular competitive-price gasolines. "High-test" fuels may also have a high anti-knock rating.

Jan 1, 1931

By W. A. Calhoun

"INTRODUCTION A letter from S. D. Strauss, vice president of Metals Reserve Company, Washington, D.C., dated May 22, 1945, to the chief of the Metallurgical Branch, Bureau of Mines, in Washington; includes the following: Because of the present critical shortage that exists in the supply of corundum required by certain industries in war production, the Reconstruction Finance Corporation, Mr. W. C. Keeley, Vice Chairman for Metals and Minerals, War Production Board, has recommended that the Reconstruction Finance Corporation though Metals Reserve Company, proceed with preliminary mill testing of the corundum ore in Gallatin County, Montana, and that the results of that testing be transmitted to the War Production Board. If the results of the testing work are considered satisfactory, Metals Reserve Company will then provide for the actual mining and milling of the ore for the production of corundum concentrates.Pursuant to the above stated recommendation by the War Production Board, Metals Reserve Company desires to make -use of the facilities of the Bureau of Mines testing plant at Rolla, Missouri, for conducting sink and float and other concentration tests on representative samples of the Montana corundum ore. Two, and possibly three samples of ore are to be tested which will have an aggregate weight of approximately 50 tons."

Dec 1, 1947

By John E. Trombly

System objectives and design criteria for an in-mine ULF radio paging system are discussed Coding formats, frequency and bandwidth selection criteria leading to the system design are discussed. The prototype call alert transmitter and pocket page receiver is functionally described. The report includes circuit descriptions, schematics, parts lists, printed circuit fabrication and assembly drawings. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 2011

By P. B. Grote

The report provides a general description of DOM technology, sources for DOM technology, and identifies approaches and requirements for acquisition by the Enterprise of DOM technology by conventional means. The approaches identified assume the Enterprise enters into a contractual/ joint venture arrangement with an uncommitted and competent systems management firm at various stages of the DOM system acquisition process. The approaches provide for training through work/study as well as through direct participation in acquisition programs. The potential success of the alternatives are evaluated in terms of the likelihood of the acquisition of an ongoing Enterprise economic DOM operational capability. The study concludes that sources exist and that the Enterprise should under-take the development of its own technical capability through conceptual design prior to selecting its source for systems management expertise.

Jan 1, 1980