Search Documents

By R. Blickensderfer

The sparking and gas-igniting tendency of steels and alloys were evaluated my measuring the radiance of spark showers produced by grinding a sample on an abrasive wheel in air, the time required for a spark shower generated on an abrasive wheel to produce an ignition in an explosive gas mixture, and the energy and speed required for impacts between various materials to ignite an explosive gas mixture. Mixtures of air-methane were found quite resistant to ignition by showers of sparks. A mixture of air-9.S pct hydrogen was used to increase the sensitivity of the tests and to thereby extend the range of materials that could be evaluated. The results of the spark-shower tests indicate that carbon steels and the alloy steels found in coal-cutter tools are among the most sparking and most incendive of any materials tested. Stainless steels, nickel alloys, and tungsten carbide are among the least sparking and least incendive. The brightness of the spark showers depended upon the degree of oxidation of the abraded particles. Impact tests against hard rocks such as solid quartz and sandstone, showed that high-carbon steel was more inc endive in the hydrogen mixture than were the softer steels or the alloy steels found in coal cutters. Ignitions were found much less likely to occur at speeds somewhat lower than the speeds currently in use in continuous mining machines.

Jan 1, 1972

By R. K. Linn

The New Idria Mining and Chemical Co. owns and operates the New Idria mine in southern San Benito County, Calif. During 1957-59, the New Idria mine was the largest producer of mercury in the United States and its alltime production of over a half-million flasks was exceeded only by one mine. It is one of the oldest and most consistent producers in California. With the exception of 1921-22, the mine has an annual production of mercury dating back to 1854. This paper by the Federal Bureau of Mines describes the exploration, development, mining, and furnacing of mercury ore at the New Idria mine. Figure 1 is a view of the furnace plant of the New Idria mine. The purpose of this report is to promote the development and conservation of our mineral resources by dissemination of technological information on mining and processing procedures, and related practices at operating mines.

Jan 1, 1961

By L. C. IlsLey, H. H. Clark

In various publications relating to safety in mining the Bureau of Mines has called attention to the hazards attending the use of openBame lamps. An open-flame lamp is a potential source of danger in any coal mine. It may start a fire in a dry mine or an explosion in a gaseous mine. The type of open-flame oil lamp now used in mines is the product of long evolution; its principal merit is simplicity. That such a light is unsafe in an atmosphere containing gas (methane) is evident, and Sir Humphrey Davy immeasurably increased safety in coal mines when he found means of protecting a lamp flame so that it would not readily ignite gas. The safety lamp, however, gives less light than the open-flame lamp, is not as simple in construction, is more cumbersome, and must De carried in the hand .. Consequently, some miners are reluctant to abandon the open-flame lamp for the safety lamp, and risk their own lives and the lives of their fellow workers with the one rather than to be hampered by the other. When small electric bulbs, with their clear, white light, and small electric storage batteries became available, the advantage of combining these elements for a miner's lamp seemed manifest. The combination looked simple and safe, but was soon found to have elements of danger and weakness peculiar to itself. The Bureau of Mines showed, in 1911, that the breaking of a miniature electric bulb in an inflammable mixture of gas and air might ignite the mixture, so that only the fragile glass of the lamp bulb might stand between the miner and injury or death. There Was also a possibility that sparks from the small battery would ignite gas, and the accidental spilling of the contents of a battery on the miner's clothing or skin was a possible source of injury. The first portable electric miner's lamps that were carried in the hand, or with the battery strapped to the back and the light carried on the head, were exceedingly crude and were designed without appreciation of the sources of danger. The possibility, however, of producing a safe and practical miner's lamp by the proper combination and design of the elements available promised to increase safety so greatly that the Bureau of Mines attemr>ted to stimulate better design and construction by careful investigations and the establishment of an approval system that would be an assurance to the miner and an advantage to the maker of the lamp. As a result various manufacturers submitted types of lamps, cords, and bulbs for test and cooperated with the bureau in efforts to so improve the safety features of these devices that the lamps would P&$ specific tests for approval.

Jan 1, 1917

By R. A. Egen

The purpose of this book is to provide an indication of what good hoisting practice is and how it might be achieved. To this end the book contains discussions of equipment and inspection and maintenance procedures developed and used by mining people in striving for safe, reliable hoisting equipment. Most of this information comes from domestic practice; the rest is foreign, notably from Canada. Most things discussed have long proved their general worth, and others promise to; a few are beginnings. However, nothing is conjectural or theoretical; the practices described herein are in use somewhere in the mining world. The stress is on equipment in use; it is not a design-guidelines manual. Nevertheless, there are some sections dealing with design material since it may be of value in a maintenance/ replacement sense. Mine hoisting installations encompass such a wide variety of equipment and conditions that it is impractical to specifically cover them all. This book mainly treats conventional systems using conventional components with some discussion of the more common unconventional (special) systems in use. There is no recognized definition for a "conventional" mine-hoisting system. Herein the term means those systems most commonly used in daily operations for transporting men, materials, and product-electrically driven drum and friction hoists, with guided conveyances running in vertical or inclined shafts. Beyond this, what "conventional" means is probably best illustrated by the topics discussed.

Jan 1, 1975

By Rudolf E. Greuer

This report contains the practical application of a computer program for the simulation of ventilation systems under the influence of mine fires and other emergencies on five hardrock mines. The introduction describes the need for such a program, its basic features, and the range of its applicability which is mainly a function of the available ventilation data. The second chapter discusses program modifications, whose necessity or desirability was, during the application, discovered. The following five chapters, which comprise the major portion of the report, give the detailed description of the program application on the five mines. For every one of the selected mines, the ventilation system, the source of the used ventilation data and their preparation for computer simulations are outlined. Based on data for the airflow distribution solely, fumes concentrations in the mines are calculated for several assumed fire locations. Based on data for airflow and pressure distributions, ventilation disturbances caused by fires as well as the resulting fumes concentrations and temperatures are determined. The consequences for escape routes and the possible means to keep them free of fumes are discussed. To investigate the capabilities of the program, other contaminant sources and other potentially dangerous ventilation factors, like fan failures and changed surface temperatures, are simulated also. The results of the calculations have been entered into ventilation plans which makes them easier to scrutinize. All significant computer printouts have been attached.

Jan 1, 1981

Underground coal mining continues to evolve in the U.S., and more reserves are being mined under deeper cover, with worse roof, or with interactions from previous workings. At the same time, the mining community is responding to higher safety standards and intense competitive pressures. The need for effective ground control design has never been greater. Ground control safety issues that have been addressed by recent the National Institute for Occupational Safety and Health (NIOSH) research include: Improving roof support performance; Maintaining safe tailgate escapeways from longwalls; Optimizing pillar design for retreat mining; Controlling multiple seam interactions; Predicting roof conditions during extended cuts, and; Preventing massive pillar collapses. As funding from both government and the private sector has diminished, the emphasis in research has focused on providing the mining community with practical techniques for improved ground control design. Many projects have successfully employed empirical methods that emphasize the statistical analysis of case histories from underground mines. Other projects have employed numerical models and large-scale laboratory testing of roof support elements. Using these data, NIOSH has developed an entire toolbox of computer programs that have been effectively transferred to the mining community.

By Robert A. Elgin

The Leadville mining-district (fig. 1) covers approximately 8 square miles adjacent to Leadville, the county seat of Lake County, Colo. It is famous for its large production of rich ores containing zinc, lead, copper, gold, and silver. Some manganiferous ores also have been produced.

Jan 1, 1949

By Joseph Daniels

[Adequate supplies of suitable coal and coke are prime requisites in many industries, particularly those dealing with the utilization of mineral resources, recently interest has been focused on the possibilities of using electricity produced at Bonneville and Grand Coulee, Wash., in many electrochemical and electrometallurgical processes, in which core or some form of carbon is necessary in addition, discussion has been revived on the possibility of making iron and steel by the conventional methods employed in blast and open-hearth furnaces. The subject also is important at this time because of its relationship to industrial preparedness for national defense. A supply of coke from local sources on the Pacific coast is necessary in any program of production for strategic sufficiency of certain materials. An anal trio involving tae establishment of such industries should include detailed data on available supplies of coal, the quality and properties of the coke produced, and the technologic and economic factors involved in manufacture of echo and disposal of byproducts.]

Jan 1, 1941

By Robert L. Virta

This U.S. Bureau of Mines paper discusses the structure of the talc industry, talc production, processing of talc ore, applications and demand for talc, and the outlook for the talc industry.

Jan 1, 1989

By J. R. Ross

A reconnaissance for sources of scandium and a metallurgical investigation of recovery methods for byproduct scandium from uranium mill solutions were conducted by the Bureau of Mines. The work on scandium was undertaken to obtain information on domestic resources and to explore and develop recovery procedures in consonance with the Bureau's long-range program for conservation and wise utilization of mineral resources. The element scandium is widely distributed in the earth's crust in trace amounts, but it seldom occurs as an important constituent in any mineral. An exception is thortveitite, (Sc,Y)2 Si207) a rare mineral that contains various amounts of scandium and yttrium and may contain up to 42 percent scandium oxide (SC203). Knowledge of the chemistry of scandium has expanded rapidly in recent years (1, 4, 9)4 but only fragmentary information is available about the metal because it is still largely a laboratory curiosity without established uses (2, 3). A recent study shows some of the physical proper-ties of the metal are (1) density of 3.05 grams per cubic centimeter) (2) melting point of 1,540° C, (3) hexagonal close-packed structure) (4) hardness of about 50 Brinell (500-kilogram load), and (5) an alloy behavior similar to yttrium and rare-earth metals (2). The price of $2,850 a pound for scandium oxide of 99.9 percent purity and $2,700 a pound for oxide of 99 percent purity reflects the scarcity and complex chemistry of the element.

Jan 1, 1962

By BUREAU OF MINES

This report is submitted in accordance with provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1954 has been divided into two separate publications. Each is being published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5118, Part I - R. I. 5119, Part II - 011 From Coal. 011 From 011 Shale. The introduction, identical in both reports, summarizes research progress in 1954 under the entire Synthetic Liquid Fuels program. A free copy of either publication may be obtained by writing to the Bureau of Mines, Publications Distribution Sec- tion, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Mar 1, 1955

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, and control of anthracite-mine fires, it was observed that the carbon monoxide disappeared from a sealed fire area much more rapidly than could be explained on the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance: (1) That the carbon monoxide, was oxidized at temperatures below 150° C. by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C. carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By Mark L. Chatman

This report presents an economic mineral assessment and Inventory of mines and prospects In the approximately 176,000-acre Patagonia Mountains-Canelo Hills Unit of Coronado National Forest. Deposits or areas most likely to experience future development are characterized in terms of their economics, based on data acquired by the author from a variety of sources, and supplemented by USBM field data collected by other workers in 1990 and 1991. Numerous mine maps, rock-chip sample assays, and detailed descriptions of mine and prospect sites are in this report and appendixes. Heavy but sporadic mining, mainly between the 1850's and 1950's was nearly all confined to the Patagonia Mountains. High-grade sulfide veins, replacements, and skarn deposits accounted for most of the production, which included large quantities of zinc, lead, copper, and silver, and considerable quantities of gold. Small Quantities of molybdenum, manganese, tungsten, and placer gold have been mined. Most of the traditionally mined metalliferous sites will not see future activity due to the low tonnages present and removal of most high-grade rock. Possible future development areas include copper porphyries and breccia pipes; most are too deeply buried for current development. Localities where similar deposits may be concealed are identified.

Jan 1, 1994

By BUREAU OF MINES

This report is submitted in accordance with provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1954 has been divided into two separate publications. Each is being published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5118, Part I - R. I. 5119, Part II - 011 From Coal. 011 From 011 Shale. The introduction, identical in both reports, summarizes research progress in 1954 under the entire Synthetic Liquid Fuels program. A free copy of either publication may be obtained by writing to the Bureau of Mines, Publications Distribution Sec- tion, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Mar 1, 1955

By Doris M. Hyde

Mineral output and trade in the Central American countries were directly or indirectly affected by the sometimes violent civil unrest and recessionary economic developments that have pervaded the region for several years. Central American countries found their foreign exchange export earnings and traditional market areas shrinking while essential import costs were rising. Restricted spending measures were adopted by governments and private industries. Domestic investment funds for mineral development and exploration projects were among the first casualties of these austere budgetary measures, especially since weak demand and depressed mineral prices diminished the probability of a favorable cost-benefit ratio. The lack of physical security and political stability also discouraged private foreign investment. The United States Congress enacted the Caribbean Basin Economic Recovery Act of 1983 (19 U.S.C. 2702), more popularly known as the Caribbean Basin Initiative (CBI). This legislation was designed to stimulate economic recovery and promote economic development by increasing private investment and trade in the Caribbean Basin countries. The act provided for the elimination of U.S. duties on most trade items imported directly from eligible Caribbean countries, provided at least 35% of the product value originated in the region. The financial assistance components of the CBI were to be supportive of the basin's private sector as well as assist general economic stabilization programs.

Jan 1, 1985

By Michael L. Boucher

Copper and nickel sulfides occurring in the Duluth Complex of northern Minnesota were examined at the Bureau of Mines, A microscopic study was undertaken to determine the mineralogy and paragenesis of the ore minerals. Eighty-two samples were taken from one deep diamond drill core located near Babbitt, Minn. Modal analyses are presented for the Duluth Complex rocks and for the are minerals in the major mineralized zone. The major sulfide minerals are chalcopyrite, cubanite, pyrrhotite, troilite, and pentlandite. Results of this investigation suggest that the mineralization is related to the structural features of the enclosing rocks: pores, open fractures, and cavities. The pyrrhotite-troilite-pentlandite assemblage is believed to have formed from an immiscible sulfide melt, probably associated with the troctolitic rocks. Most of it settled to the very porous base of the Duluth Complex, and to the other porous zones near xenoliths; small portions were trapped higher in the section. A later introduction of a copper-rich sulfide melt replaced some of the pyrrhotite-troilite and oxides, and filled in the remaining open spaces and fractures in the Duluth Complex and those of the adjacent footwall rock.

Jan 1, 1975

By P. B. Altringer

The Federal Bureau of Mines conducted a study to determine if residues from fractional distillation represent a potential source of mineral values. A literature review and discussions with tar sand specialists failed to disclose the mineralogical nature of residues remaining after bitumen extraction. To develop this information, pilot plant tar sand residues or toluene-cleaned tar sands from 23 deposits were examined. The nature of the residues was determined by standard mineralogical methods and the chemical compositions were determined by X-ray and ICP (inductively-coupled plasma spectroscopy). None of the sands or concentrates examined contained sufficient valuable minerals to be economically important.

Jan 1, 1982

By Sara Jane Boles

In recent years the interest in rare-earth compounds as refractory materials has exceeded the available literature on the subject. While some basic properties, such as density and melting point, of the more readily available rare-earth compounds have been reported in the literature, relatively few papers can be found that deal comprehensively and primarily with high-temperature refractory properties and applications of rare-earth oxides, carbides, sulfides, and nitrides. Therefore, this bibliography has been pre-pared for the use of the ceramic industry as a guide for locating and utilizing the scattered and frequently fragmentary information available. The term "rare earths", as applied in the literature search for this bibliography, is understood to include the following elements: cerium, dysprosium, erbium, europium, gadolinium, holmium, lanthanum, lutetium, neodymium, praseodymium, samarium, terbium, thorium, thulium, uranium, and ytterbium. (On the periodic chart, these elements appear as numbers 57 through 60, 62 through 71, 90, and 92.) It is emphasized that many of the abstracts included are from papers in which the rare-earth compound or compounds are treated along with several other ceramic materials, are mentioned only secondarily, with primary interest placed on a more commonly used refractory material, or are used as part of a mixture of materials formed experimentally and reported on in the paper. As the better known rare-earth materials, such as the oxides of uranium, thorium, and cerium, appear more frequently in the literature, they also appear more frequently in this collection. Articles abstracted include only information on the basic properties that are of interest to the refractories investigator. References to crystal lattices and related topics are generally excluded from this publication. The temperature 1,500° C. has been set arbitrarily as the lower limit for reported data on thermal properties. However, because of the scarcity of information, some reports are included in which data are limited to those obtained at lower temperatures. Many of the articles abstracted include lists of references that will be of additional assistance in pursuing specific lines of investigation.

Jan 1, 1962

By A. B. Hooker, L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts,· and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used. Electrical problems of many kinds must be solved in dealing with the various phases of electric shot-firing. Success in using an electric detonator is closely linked with the resistance of its bridge, the resistance of its leg wires, and the insulation of its current-carrying parts. The proper layout of a circuit where a number of shots are to be fired simultaneously depends not only on the types of detonators that are used and their arrangement and interconnections, but also on the size and insulation of the wire leading back to the source of power, and even on the source of power itself. Various types of electric shot-firing machines have been developed, and these offer still another field for study. In investigations of electric detonators and electric blasting equipment, the oscillograph is valuable because it can record electrical activity over very short intervals of time. By its use more complete information about electrical performance can be obtained than by any other means.

Jan 1, 1926

This report, 27th in a continuing series1, describes Bureau of Mines research and technologic work on coal and related investigations during 1962. While the brief discussion in each section of the report presents only the highlights of Bureau work during the year, details of many investigations can be found in publications cited in this text. Other work, reported here for the first time, will be covered in greater detail in later publications. Recent trends in coal research and technology both at home and abroad were reviewed in several publications2. Bureau research, as in the past3, continued to stress improved methods of mining, preparing, processing, and using coal. The program included a wide variety of applied and basic studies for developing information useful to the coal mining industry and the coal consumer while promoting wise conservation and utilization of our coal resources.

Jan 1, 1963