Search Documents

By D. Johann, E. Zanetti, I. A. S. Brum, P. M. Zancan, A. F. Castro

"This study was done from a sample of coal mined at the Vale-Mozambique mine, located in Moatize district, Tete Province. The aim of this work is to analyze the reagent system in the flotation of coal fines belonging to the Upper Chipanga layer (UC). Among coal processing methods, flotation stands out as one of the most important for the concentration of this material, in particular in the treatment of fine particles. The total feed of the Vale-Mozambique processing plant is 8,000 tph of coal, where 10% of this feed corresponds to the fine fraction that feeds the flotation circuit. The material used in this study had a particle size of 96% smaller than 0.25 mm. The reagents used in the flotation tests were betacol and diesel oil as hydrophobizing agents and MIBC as frother. The range of betacol concentrations in the first test phase was 200 g/t to 500 g/t, and in the second phase 200g /t to 500g /t while diesel oil and MIBC were kept constant at 300 g/t. The immediate analysis followed the Brazilian standards NBR 8289, NBR 8293, NBR 8290; and NBR 8299. The results showed that it is possible, from a feed with ash content around 22.84%, to obtain products with levels below of 10% ash, with a mass recovery around 50%. The recovery of carbonaceous matter was also evaluated and presented positive results. Complementing this study, the effect of H2O recovery was evaluated and it was observed that for the concentrations of betacol the recoveries ranged from 6 to 9%, and for diesel oil plus MIBC were 4 to 7%.INTRODUCTION Considering the increase in population and energy consumption as humanity has been living along the last decades and the consequent demand for non-renewable natural resources, it is clear the challenge of the mineral industry in the search for new technologies and improvement of the existing ones. This challenge is justified by the need for better industrial results and to meet the market specifications, taking into account the reduction of deposits with higher contents and the need for beneficiation of more complex ores, lower levels and lower release granulometry. Usually in these situations, processes already well-established as the gravimetric (Sampaio and Tavares, 2005) have not good results."

Jan 1, 2018

By Chanki Jeong, Heechan Cho

In this study, batch flotation experiments were conducted to recover rare earth elements (REE) from an REE ore deposit in the Mushgai Khudag area, Mongolia. Apatite was found to be the major REE mineral while monazite and xenomite were observed as minor minerals. The main purpose was to float apatite to increase the REE content. Oleic acid was used as collector and MIBC was used as frother. Sodium silicate was used as a depressant for iron compounds. NaOH was used to adjust the pH of the flotation to about 9.5~10.0. The particle size was 90% less than 152 ?m (- 100 mesh). The content of REE elements was analysed by ICP - OES to determine the contents of REE such as Ce, La, Nd, Pr and Y. When sodium silicate was used, the best result was obtained using 0.2 mL of sodium silicate, 2 mL of oleic acid and 2 mL of MIBC. Under these conditions, the recovery of REE was about 78% and the grade of the first froth product was 42,995 ppm Ce, 24,088 ppm La, 14,236 ppm Nd, 4,388 ppm Pr and 1,570 ppm Y. When conducting flotation after iron minerals were removed by magnetic separation, a better result was obtained; with 2 mL of oleic acid, 2 mL of MIBC and no sodium silicate, the recovery was increased to 90% and the grade was also increased to 58,600 ppm Ce, 28,624 ppm La, 17,160 ppm Nd, 5,348 ppm Pr and 1,971 ppm Y.

Jan 1, 2014

By C. Y. Wang

Anodic reaction mechanism of complicated antimony-lead concentrate in Slurry Electrolysis has been investigated by the anodic polarization curves determined under various conditions. The main reactions on the anode are the oxidation of FeCln (2-n), though the oxidation of jamesonite particle on the anode can occur during the whole process, it is less. With the help of mineralogy study and relevant tests, the leaching reaction mechanism of jamesonite and gudmundite during Slurry Electroly-sis has been ascertained also. Because of the oxidation reaction of FeCl3 produced by antimony-lead concentrate itself, the non-oxidation complex acid dissolution of jamesonite, the oxidation complex acid dissolution of gudmundite, and the oxidation of air carried by stirring, the leaching ratio of antimony reaches to about 35% when using HCl-NH4Cl solution to leach antimony-lead concentrate directly. So given the theoretical electric quantity, which to oxide antimony in Slurry Electrolysis, all of antimony, lead and iron, which contained in antimony-lead concentrate, are leached.

Jan 1, 2014

By Tong Guan, Guangqin Fu, Lihong Deng, Xiaotong Zhou

The raw ore contains many kinds of valuable metal elements. It is rich in valuable metal elements, such as Pb, Zn, Sb, Sn, Ag and is associated with S,Fe,As,In,Cd. A new technology which includes medium intensity magnetic separation, preferential lead flotation, zinc-sulfur bulk flotation, zinc-sulfur flotation separation, tin gravity separation and tin slime flotation was chosen to recover valuable minerals in the raw ore, and the iron concentrate, the lead concentrate, the zinc concentrate, the sulfur concentrate and the tin concentrate can be obtained. To the zinc-sulfur bulk concentrate with the grade of 7.21%Zn and 16.97%As acquired by the zinc-sulfur bulk flotation, two different flowsheets of Zn-S separation technology are chosen to study. The lab test shows that when using lime+DM as depressor, the zinc concentrate assaying 47.73%Zn with the recovery of 95.01% can be obtained and the test indexes are better than that of the flowsheet which using lime as depressor. At the same time, the Cd content is 0.65% and the In content is 0.10% in the zinc concentrate, so they all reach the smelting comprehensive recovery standards and the As content decreases to 0.23%. Finally the flotation separation of christophite and As-bearing sulfide minerals can be successfully realized.

Jan 1, 2014

By N. Vorob?ev-Desyatovskii

The process of gold(I) adsorption on activated carbon (AC) from aqueous Na[Au(CN)2] and the state of the adsorbed gold cyanide complex on the adsorbent surface was investigated by photometry, XPS, XANES methods. By DFT method, quantum-chemical calculations were performed of the gold cyanide species on activated carbon surface. It was established that the binding of gold(I) with the surface of carbon involved several simultaneous processes governing the selective adsorption of gold(I) from the cyanide solutions.

Sep 1, 2012

By Juan B. Yianatos

"After almost 100 years, since the first commercial application began in Australia, flotation has shown an extraordinary growth and nearly 2 billion tons of ore per year are presently treated by flotation processes. During this time flotation has promoted a wide scope of research activities ranging from fundamental chemistry and hydrodynamic studies to studies of industrial operations. In general, fundamental studies have been mainly related to ideal situations. In recent years, however, large efforts have been focusing on achieving a better insight into the actual sub-processes provided by the development of new and more sophisticated instrumentation. Since the massive incorporation of flotation columns, around 15 years ago, a renewed interest in flotation fundamental studies, process modelling and new cell designs have been observed worldwide. The key role of the froth has been recognized as an independent and sometimes rate limiting process step. Thus, separation of pulp and froth process stages seems the most appropriate in terms of process modelling, diagnostic, design and scale-up purposes.In relation to flotation equipment development, until the middle of the 1970?s, only the sub-aeration mechanical cells were dominant. Since the 1980?s, the use of pneumatic cells and forced air mechanical cells has emerged strongly. Also, in the last decade, flotation equipment has shown a dramatic increase in size, reaching values of 200m3 in unitary mechanical cells and more than 300m3 in columns. The general feeling, however, is that, despite the great advance observed in terms of process knowledge, the mechanisms and principles of industrial flotation cells design and scale-up are still not fully understood.Advances in process instrumentation and control now in use allow for more efficient operations, both in metallurgical performance and savings in operating costs.INTRODUCTIONFlotation is a widely used process within the minerals processing industry, as well as being used for water treatment and de-inking of recycled paper. Froth flotation started in Australia at the beginning of the 20th century and since then flotation technology has made significant advances. Flotation was firstly applied to sulfide ores. The largest tonnages treated by flotation are copper and copper/molybdenum ores, handling about 50% of the total ore processed. Also significant are phosphate, iron ore and coal treatments. At present, Chile is the foremost copper producer in the world with around 35% of the world?s production. Figure 1(a) shows the evolution of copper production in Chile over the last decade. The total amount of fine copper produced in year 2001 was 4.7 million tons, from which 3.2 million tons was processed by flotation while 1.5 million tons went through LIX-SX-EW processes, which also showed significant development during the same period (Anon, 2001). The total flotation treatment of copper ores in Chile is about 325 million tons per year (Anon, 2002), so the world treatment of copper ore by flotation can be estimated at about 1 billion tons per year. Consequently a total of nearly 2 billion tons of ore per year is presently processed worldwide by flotation (Fuerstenau, 2001). In order to handle the higher tonnage of low-grade ore, a worldwide trend towards the development and use of larger flotation machines began in the 1960?s. Figure 1(b) shows that the trend became extremely marked from the beginning of the 1990?s, which is consistent with the strong increase in copper production during the same period."

Jan 1, 2003

By Y. S. Sun, P. Gao

"In this investigation, a pilot-scale suspension magnetization roasting reactor was introduced and used to enhance magnetic properties of an iron ore. Consequently, the effects of roasting temperature, reducing gas CO flow rate and fluidizing gas N2 flow rate on the magnetization roasting performance were investigated. The results indicate that the hematite and siderite are almost completely converted into magnetite by a gas mixture of 3.5 Nm3/h CO and 2 Nm3/h N2 at roasting temperature of 520 °C. Under the optimized conditions, the magnetic iron concentrate with an iron grade of 60.18% and iron recovery of 90.17% was achieved. The XRD and Fe mineral phase analyses revealed that most of the hematite and siderite were converted to magnetite, and the magnetic properties were greatly enhanced. INTRODUCTION The steel and iron industry in China has rapidly developed in recent years requiring a large quantity of iron ores. Low-grade and complex iron ores are currently the overwhelmingly dominant mineral resource for iron in China. Therefore, China depends on imported iron ore resources heavily, resulting in an increase in the production costs of iron-making and steel-making[1-3]. Using domestic resources to produce a steady supply of high-quality iron ores is an important step toward the sustainable development of the steel and iron industry[4-5]. The iron ore from Jiuquan iron and steel company is abundant and recognized as typically complex iron ore resources in China. Magnetization roasting followed by low-intensity magnetic separation has been proven as the most feasible methods to upgrade refractory iron ore[6-10]. In present research, an innovative roasting technology, namely suspension magnetization roasting, was developed and applied to recover iron from a typical refractory iron ore. Suspension magnetization roasting technique and equipment developed by Prof. Yuexin Han’s Group at Northeastern University (NEU) is an effective way for the utilization of refractory iron ore. The advent of suspension magnetization roasting will, in China and even globally, produce a significant technological revolution in the field of iron ore beneficiation. Based on the previous works, this paper mainly described experiments on the separation and recovery of iron from a complex refractory iron ore by means of suspension magnetizing roasting and low-intensity magnetic separation processes. The purpose of the research is providing a new technology for effective utilization of refractory iron ore. Process parameters that affected the separation and recovery rate of iron were conducted and optimized, and the reaction process was analyzed by XRD and Fe mineral phase analysis."

Jan 1, 2018

By Junwei Han, Kai Xue, Wenqing Qin, Tan Xu, Fen Jiao, Lianbing Cai, Wei Liu

"The research aimed at solving the problem of the stacked spent magnesia-chrome refractories using in non-ferrous metal smelters, which contain various heavy metals and are considered as a hazardous waste. The purpose of the research is to recycle the spent refractories environmentally and economically using gravity separation and flotation to obtain metal concentrates for smelting and using chloridizing volatilization to remove the trace metals from tailings, providing raw material to reprocess magnesia-chrome refractories. In the course of the study, laboratory techniques for the preparation of experimental samples of spent magnesia-chrome refractories were developed including the sequence of operations of material grinding, gravity separation, tails regrinding, flotation, filtration and subsequent unification of concentrates, filtration and chloridizing volatilization of tails, and collection of volatiles. Laboratory tests carried out on several types of samples of spent magnesia-chrome refractories from different smelters showed that gravity separation provided increase in quality of concentrates including about 80% metals (including Ag, Pb, Bi) and flotation separation provided increase in recovery of concentrates under the condition of 200g/t of emulsified kerosene, and 500g/t of combined collector. Based on combined technology of gravity and flotation separation, about 90% metals were recovered from the refractories by a closed-circuit test and the total concentrates contained 40% metals, which can be returned to smelting process as a feeding. Because a small amount of metal in raw materials will seriously affect the performance of refractories, chloridizing volatilization is necessary for removing the remaining 10% metals from tails mixed 8% coke and 13% magnesium chloride at a temperature of 1200°C. Thus, the tailings can be reused as a raw material for new refractories.INTRODUCTION Magnesia-chrome refractory has been used extensively in various industries such as secondary metallurgy, non-ferrous furnaces and cement making due to their high temperature stability, low thermal expansion and outstanding erosion-corrosion performance at high temperatures (Gotod et al., 2005; Vezza et al., 1997; Gregurek et al., 2015). Generally, the magnesia-chrome refractories are produced from a mixture of magnesia and massive variety of chrome ores. However, massive chrome ores are being depleted throughout the world. Even more serious is that the heavy metal chromium (Cr) can transfer into soil and water, which will have an influence on the survival and development of human beings (Zhao et al., 2006; Jiang et al., 2004; Qintie et al., 2013). As a result, regulations treating spent magnesia-chrome refractories as potentially hazardous waste are being enforced, making their disposal difficult and expensive."

Jan 1, 2018

By Yuexin Han, Wenbo Li, Yan Shan, Yanjun Li, Shumin Zhang

"With the accelerating pace of resource extraction, the quality of resources is decreasing, and the old tailing dams which have served for several decades have become the focus of attention. The secondary recovery of valuable metals in the tailings is an important aspect of the comprehensive utilization of tailings. The average iron content of iron tailing is 8%-12% in China. The research aimed at exploring the low-cost and efficient technical route to recycle eastern tailings of Anshan iron mining area. The purpose of the research is to scientifically find the rational conditions of magnetizing roasting and to provide an increase in recovery and quality of concentrates. The eastern tailings of Anshan mining area belong to high silicon bearing iron tailings, iron mainly exists in form of hematite-limonite with an iron grade of 10.60%, the main component of gangue is SiO2 with a grade of 76.22%. In order to reduce the influence of the tailings on the environment, fluidized magnetizing roasting and low intensity magnetic separation for the eastern tailings of Anshan mining area were carried out to improve the utilization of the tailings. The results indicated that an iron concentrate with an iron grade of 65.30% and a recovery of 85.85% could be obtained under the conditions of gas flow rate 8 m3/h, H2 concentration 50%, fluidized magnetizing roasting temperature at 600? for 20s. Phase analysis, magnetism analysis and XRD analysis on roasted materials indicated that hematite-limonite could be transformed to magnetite during the fluidized roasting, then the effective separation of iron and gangues could be made easily by the weak magnetic separation. INTRODUCTION It is universally acknowledged that the grade of iron ore in China is low, the output rate of iron ore tailings is high, usually more than 60%. At present, the comprehensive utilization rate of iron ore tailings is low in China. Generally, the iron ore tailings are stockpiled in the tailings dam. The tailing dams not only occupy a lot of land, but also takes a lot of money to construct and maintain. In addition, the noxious substances in the tailings, such as residual flotation agents and heavy metals, have a severe impact on the ecological environment. There is little doubt that tailing dams have a visual impact on the environment due to their regular geometric shape. Iron tailings can be treated as compound mineral, which is an important component of comprehensive utilization of mineral resources, and is an has been widely concerned. Lots of scholars have done a large amount of research work on a large number of iron ore tailings. Since the iron mineral crystal grain size is fine and the iron grade is low, the iron tailings have failed to achieve good selection criteria."

Jan 1, 2018

By Hong Zhong, Shuai Wang, Zhanfang Cao, Ting Dai

"Manganese is widely used in industries such as the steel industry and is now an essential element in modern industry. Technologies for the efficient and clean utilization of manganese resources must be developed and employed to ensure the sustainable growth of the manganese industry. Our research focuses on the use of beneficiation technologies to improve the grade of ores or the replacement of low-grade manganese carbonate ores with high-grade manganese oxide ores, and thus, to reduce reagent and energy consumption and the yield of electrolytic manganese residues from metallurgical processes; the study of leachate purification technologies; the study of electrochemical behaviors during electrolysis and energy-saving electrolysis methods; the development of chromium-free passivators as alternatives to the highly toxic potassium dichromate passivator; the non-hazardous treatment and resource utilization of electrolytic manganese residues and other manganese by-products; and the development of new manganese products. INTRODUCTION Manganese is widely used in the steel industry, nonferrous metallurgy, the chemical industry, electronics, batteries, agriculture, etc. Globally, more than 90% of manganese is consumed by the steel industry, and thus, it is said that ""No steel industry without manganese""(Banerjee et al. 2017, Zhang et al. 2017). Current manganese resources mainly include manganese ores, marine manganese nodules and waste catalysts. The total global output of manganese ore from land deposits is 18 million tons (metal volume), and the reserves, most of which is in the form of manganese oxide ores, are estimated to be 620 million tons (metal volume). More than 400 manganese ore deposits with a total reserve of 1.22 billion tons have been discovered in China. These deposits are predominantly manganese carbonate ores. Marine manganese nodules exist on the surface of the deep seabed at depths of 2000-6000 m. These nodules, which are also called polymetallic nodules, manganese balls, manganese aggregates and manganese tumors, are mainly composed of iron and manganese oxides. The total reserves of these resources add up to more than 3 trillion tons. Furthermore, the manganese in manganese-containing catalysts can be recycled after they become inactive."

Jan 1, 2018

By S. L. Gubin, T. V. Ignatova, A. V. Levshin, D. O. Sharkovsky

"Flotation process applied for concentration of unoxidized ferruginous quartzites by PJSC Mikhailovsky GOK (MGOK) is based on wet magnetic separation of strong magnetic minerals. However quality of the resulting concentrate (Fe65-66%) is insufficient for production of metallics. Quality upgrade of magnetite concentrate via flotation has been implemented by MGOK to produce premium quality magnetite concentrate.Flotation is a challenging process due to sensitivity to varied amounts of reagents, fine and coarse mineral ratio, particle contact (retention) time and temperature of feed. Tomah’s PA-14 reagent (USA) has proven efficient for application in flotation of MGOK’s magnetite concentrate.Objective of this work is to select and prove applicability of selective agents for flotation upgrade of magnetite iron ore concentrate.Series of flotation tests has been carried out with application of new highly selective collecting agents produced by Akzo Nobel (Sweden), Clariant (Germany) as well as Akzo Nobel’s and Tomah’s cationic collector mix to improve performance efficiency of flotation process. Tomah’s flotation agents and Akzo Nobel’s Lilaflotproved to be the most effective for purposes of concentrate quality upgrade to Fe69.0% via flotation.Testing Method: Following scientific research methods were applied for testwork: system analysis, mathematical statistics, observation, comparison, trial (experiment).To determine key process factors a series of pilot tests was carried out. Most of the testwork was performed by PJSC Mikhailovsky GOK’s Central Process Laboratory.Work Results:-optimized flotation performance modes were defined to ensure production of three types of low-silica concentrate, i.e. containing SiO25%, SiO24% and below SiO23% by weight. Most efficient selective agents applicable for flotation have been defined. Mixture of higher aliphatic amines has proven to intensify selective flotation of quartz. It enables higher yield of chamber product maintaining desired quality of concentrate.Achieved process operation and performance factors have been revaluated.Value for Advancement and Expansion of Mineral Processing:Flotation of concentrate has enabled expansion of PJSC Mikhailovsky GOK’s production capacity, improved production quality, helped to maintain sustainability and competitive advantage of the company."

Jan 1, 2018

By P. M. Solozhenkin, V. N. Kovalev

Russia is a global antimony market leader. The three major antimony production provinces are Sakha Republic (Yakutia), Krasnoyarsk Territory and Trans-Baikal Territory. Russia’s largest antimony resources are Zhipkozhinsky and Solonechensky deposits in Sakha Republic (Yakutia) and Olimpiadinskoe deposit in Krasnoyarsk Territory. This work demonstrates the efficiency of computer programs and chemical technology aimed at the study of the behavior of collectors used in the processes of flotation of antimony, arsenic and Au (I – III) minerals. The most promising collectors for the flotation of ores containing antimony and gold on the basis of P(V) and compounds with S, O and N atoms were chosen. The mechanisms of interaction with the mixtures of two or three components of collectors were studied. High recovery of antimony and gold was reached in the processing of Au-Sb ores of Sarulah and Sentachan deposits in Sakha (Yakutia). X-ray radiometric methods of separation of antimony ores of Trans-Baikal Territory deposits were proposed. In order to choose the most cost-effective solvents for hydrometallurgical processing of Sb, Au-containing concentrates the method based on clusters formation between transition solvents and antimony minerals was suggested. The nature of Au losses was theoretically revealed in the sulfide-alkaline process. On the base of computer simulation, the formation of various complexes of (KAu) types was developed, for example, hydrosulphidic gold, thiosulfates of gold - Na3AuS4O6, antimony and arsenic gold, trithiostibate (III) and trythioarsenate (III) KAu were produced. The practice of processing of goldantimony concentrates to produce high-quality antimony trioxide and antimony-gold containing alloy (AGCA) regarding the special conditions of the Far North region, were analyzed. The affinage of AGCA was recommended. Creative project development of antimony industry in Russia in order to produce antimony compounds and pigments, including pyriform compounds and flame retardants (antipyrenes) is discussed.

Jan 1, 2018

By S. V. Volkova, S. V. Mamonov, T. P. Dresvyakyna

"The purpose of the work is complex processing of sulphide-magnetite ores with the separation of iron into iron concentrate, copper and noble metals into copper concentrate.The work shows the research results of the material composition of the sulfide-magnetite ore in the South part of the Peschanskoye deposit. According to the research results it is found that ore contains 0.59% of copper, 66% of which is related to chalcopyrite; 39.9% of iron, 81% of which is magnetite and 3.87% is sulfur, 42% of which is associated with pyrrhotite, 65% of which is a monoclinic modification. According to the results of the mineralogical analysis, it is found that the main iron-containing mineral in the ore under study is magnetite, the content of which is 45%. In addition to magnetite, iron is found in carbonates, pyroxenes, amphiboles, chalcopyrite, pyrrhotite and pyrite. The main copper mineral in the sample is chalcopyrite; covellite, chalcosine, bornite have a subordinate value. The total content of copper minerals in the sample is about 1%. The processing technology provides the three-stage grinding of the ore to a size of 65% of the class-71 µm; a cycle of copper flotation; a cycle of pyrrhotite flotation; wet magnetic separation of flotation hosts. The following optimal parameters are established for the ore under study: the alkalinity of the slurry is 250-280 g/m3 of free calcium oxide in the liquid phase of the slurry; the duration of the main copper flotation is 20 min; the consumption of butyl potassium xanthate is 20 g/t; the consumption of the foam generator T-92 is 15 g/t; the consumption of copper sulfate for the activation of pyrrhotite is 300 g/t; the magnetic field strength is 1500 Oersteds.A complex flotation-magnetic technology for the enrichment of sulfide-magnetite ore has been developed in the laboratory in order to produce a copper concentrate containing 21.6% of copper with 91.7% extraction and an iron concentrate with 66.5% of iron mass fraction and 1.2% of sulfur with an extraction of iron into the concentrate of 87.9%."

Jan 1, 2018

By T. X. Hu

Pyrite ore is one of the main raw materials in the production of sulfuric acid. For a long time, the raw material containing the pyrite, which is used to produce sulfuric acid, generally contains S only 32%~45%. A plenty of residue from the sulfuric acid production contains 40%~50% Fe and 1%~2% S. Some of the residue also contains Cu, Pb, Zn and other harmful elements like As, thus it pollutes environment seriously and is solid waste. The research on comprehensive utilization of the residue has been made by many scholars. Through the study, the residue can only be used to pro-duce iron concentrate and the iron oxide red pigment. But because of the complex techniques, the low recovery, the low grade of iron concentrate , high sulfur in iron concentrate, causing second waste residue and the environmental pollution, the residue is mainly used as an accessory material in the production of cement, and is of a low value. Therefore, the iron resource in pyrite has not been used efficiently until now. In the paper, the flotation condition test, the flotation open circuit test and the flotation closed circuit test to produce high-purity pyrite concentrate with the low-grade pyrite ore in oceanic ore deposit have been carried on. Flotation reagent scheme of sulfuric acid used as activator and butyl xanthate as collector is determined. After four times depth cleaning, high-purity pyrite concentrate containing 52.82% S, 44.29% Fe, and only 2.89% impurities has been obtained. The S recovery is 99.13%, and the Fe recovery is 96.00% in the high-purity pyrite concentrate. The oxidizing roasting depth desulfurization experiment of the high-purity pyrite concentrate has been conducted. The results show that the Fe grade in the residue obtained is 68.58%, the content of S is 0.25%, the content of P is 0.0084%, the content of As is 0.0065%. The residue is a kind of high-quality iron-smelting raw material. Based on the above experiments, the industrial experiments on producing high-purity pyrite concentrate with the low-grade pyrite ore, and producing sulfuric acid and iron concentrate with high-purity pyrite concentrate have been done. The results indicate that the high-purity pyrite concentrate with the S grade of 51.24%, the Fe grade of 44.15% has been obtained. The iron concentrate obtained with 65.73% Fe and 0.23% S is a sort of high-quality iron-smelting raw material applied to the production of steel and iron smelting. Through the experimental study, the sulfur and iron resources in the pyrite ore have been recovered and utilized efficiently.

Jan 1, 2014

By D. Jamróz, A. Surowiak, T. Niedoba, P. Pieta

"The separation of coal material of three types of coals originating from three various Polish hard coal mines (types 31, 34.2 and 35, according to Polish nomenclature, which were steam coal, semi-coking coal and coking coal) into particle size fractions and then into particle density fractions was done and then the following parameters were measured for each particle size-density fraction: combustion heat, ash contents, sulfur contents, volatile parts contents, analytic moisture. In this way a 7-dimensional vector of data was created. Using methods of factor analysis the important features of coal were selected, which decide about their membership to individual types. To evaluate the appropriateness of the applied method the Bartlett’s sphericity test as well coefficient of Kaiser-Mayer-Olkin (KMO) were used. To select important factors the Kaiser criterion and Cattell’s scree test were used. The obtained results were compared with the results obtained in previous works by means of observation tunnels method. The results showed which particular features are crucial to define the type of coal what is also important to select appropriate method of its enrichment.INTRODUCTION Coal extracted from the mine is often a mixture of coals of various quality originating, for example, from various coal layers. One of the most important issues is to determine its quality, what means to verify if it fulfills certain requirements. Usually, such parameters as combustion heat, ash contents, sulfur contents, volatile parts contents and analytic moisture decide what the coal quality is (Drzymala, 2009). Such investigations are expensive and time consuming. That is why it seems to be important to determine the mutual connections and interactions between them what would make possible to reduce the amount of the necessary parameters. This issue was already investigated with successes in several works [Jamróz and Niedoba, 2013; 2014; Niedoba, 2015]. This work is another approach to this problem. Here, the investigation of possible reduction of researched parameters was done on the basis of the factor analysis. The obtained results confirm the earlier observations."

Jan 1, 2018

By Andrzej Luszczkiewicz, Aleksandra Potulska

"Flotation is a basic process of beneficiation of mineral raw materials which requires very fine grinding for liberation of valuable minerals. Probably flotation will also play this role in the future. In the case of flotation of difficult-to-upgrade non-ferrous ores, currently one of the most important trends in technology development is solution to fine grinding even down to a few micrometers in size and elaboration of effective flotation technology for such fine particles. Both industrial flotation data and many investigators suggest that the best results of flotation of ore minerals are observed for particle size range from 20 to 100 µm. Many base metal ores require grinding below 20, or even 10 µm, to liberate valuable ore components. However, industrial flotation of particles below 20 µm in size creates numerous challenges. Further complications may be caused by a complex nature of the ore, especially when the valuable metals are present in several different sulfide minerals. This problem occurs in the case of the Polish sedimentary copper ores. In the present study, flotation of the ore of different size distributions and degrees of grinding, having the size of particles below 25 µm, was investigated. The behavior of different sulfide minerals naturally present in the ore was analyzed. The best results of flotation tests were obtained for the ore ground down to 95% below 25 µm. Narrow size fractions -10; 10-15; 15-25; 25-40, and +40 µm were separated using special micro-sieves and mineralogical as well as chemical analyses of each size fraction were carried out for monitoring the behavior of the fine sulfide particles. Differences between flotation of chalcocite-digenite, bornite, chalcopyrite, covellite, galena and pyrite-marcasite naturally occurring in the ore were described. The role of different particle sizes in flotation performance of each mineral was also presented."

Jan 1, 2014

By V. A. Ivanova, T. N. Perunkova, N. O. Dorozhanova, G. V. Mitrofanova

"Oxyethylated compounds are used as reagents-regulators in the flotation of non-sulfide ores, in particular, apatite-containing ores. Thus, the necessary degree of selectivity in the flotation separation of two calcium-containing minerals of apatite and calcite is achieved only by using, in addition to a collector, regulators-reagents from the nonylphenol ethoxylates class. In order to establish the most optimal structures, this paper presents a comparative assessment of the physical-chemical and flotation properties of several classes of oxyethylated compounds - alkylphenol ethoxylates, aliphatic alcohol ethoxylates and oxyethylated carboxylic acid. The authors have studied their dispergating ability with respect to the air phase and calcium soaps of the carboxylic collector. Dependences of foaming properties of regulators on the degree of oxyethylation have been determined. Adsorption isotherms of sodium oleate on apatite and calcite in the presence of regulators have been obtained. It has been shown that the presence of oxyethylated compounds in the solution reduces the amount of the adsorbed fatty acid collector. The influence of the considered classes of regulators on apatite flotation has been studied. The interrelation of flotation properties of oxyethylated compounds and their molecular structure has been established.INTRODUCTION Flotation plays a leading role in complex apatite-containing ores processing. However, two calcium-containing minerals - apatite and calcite, which compose apatite-carbonate ores, are characterized by close flotation properties. Selective separation of these minerals is a difficult task, the solution of which is impossible without using reagents-regulators. One of the ways to ensure the selectivity of the flotation separation of calcium-containing minerals is the use of reagents-depressants such as sodium silicate, starch, cellulose derivatives, and others (Liu et al., 2016; Rao et al., 1989). Another method is the application of nonionic reagent regulators (Filippov et al., 2016; Filippova et al., 2014; Ignatkina, 2017), which contribute to the adsorption of the ion collector (Filippov and Filipova, 2006 Rao and Forssberg, 1997) and stability of formed froth (Sis and Chander, 2003)."

Jan 1, 2018

By E. Gock

Based on the scientific investigations on mechanochemical synthesis of metal sulphides from metals or metal compounds and sulphur or sulphur compounds, the article describes the industrial production of nanoscale metal sulphides. Special operational conditions such as inert atmosphere, size and type of the grinding balls, grinding time and specific energy input are taken into consideration. A system configuration for the manufacturing of sulphides at a capacity of 100 kg/h is presented.

Jan 1, 2014

By B. Csoke

The Bond and the Hardgrove methods are widely used for the determination of the material?s grindability. Generally, the determination of the Bond work index of inhomogeneous materials can be carried out with high deviation using the conventional apparatuses and methods, because of the highly different grindability of components. This is more significant when the composite cement?s grindability is measured, which highly affects the design and operation of cement grinding mills. A possible solution can be the combined application of the Bond-method with the determination of the component?s weight ratio in the product and perform the Bond measurement until the steady state conditions of grindability coefficient (G) and chemical composition of the components are reached. To prove the applicability of the above mentioned idea systematic Bond and Hardgrove grindability tests were carried out of two phase composite materials. The experimental results showed that the application of the combined procedure is proven in order to have a more accurate and reliable calculation of the Bond work index of composite materials, especially when the components have significant difference in the grindability and concentration. The measurements also showed the possibilities and limits of the grindability test methods.

Sep 1, 2012

By E. L. Chanturiya

During the mineral processing of pyrites sulphide ores of some deposits of Russia loss of gold with tailings and pyrite concentrates amounts up to 40%~90%. The problem of selective allocation of gold-bearing pyrite is crucial. There are 4 mineralogy-technological groups of pyrite determined in copper-zinc sulphide ores, based on the increase of contents of gold in pyrite. The gold associated with group 4 pyrite contents of 85% the total mass of gold found in the pyrite. The flotation behaviour of the enriched fractions of pyrite (98%), of the allocated from the ore of Gay deposit, were studied essentially in various conditions ?? and the charge of Butyl xanthogenate of potassium (ButX). Some products of selective pyrite flotation were investigated by methods of scanning electronic microscopy, energy-dispersive and X-ray spectral microanalyses, definition of specific resistance and thermoelectric moving force.

Jan 1, 2014