Search Documents

By I. C. Brown

Introduction Many tables of nomenclature for igneous rocks have been introduced from time to time, and each has its strong proponents. As a result, any discussion of igneous? rocks is apt to prove confusing unless the names used for these rocks are defined. This ?became so obvious to a discussion group, formed by the members of the Geological Survey of Canada in 1948, that an attempt was made to establish a scheme of nomenclature that could be used by any member mapping anywhere in Canada. The writer was asked to co-ordinate the ideas presented by individuals in the discussion group, to arrange them in tabular form, and, later, to distribute copies of the resultant table to Canadian universities, provincial geological surveys, and some other geological discussion groups. Many useful suggestions and criticisms were received, were studied ?by members? of the original group, and, so far as practicable, were incorporated in the scheme of nomenclature. The result is the table presented here. This nomenclature of igneous rocks is at present being used by most members of the Geological Survey of Canada who are working with igneous rocks, and by some Canadian universities. We hope it will be found useful and be more widely accepted. With this idea in mind, certain principles were adopted in drawing up the nomenclature.

Jan 1, 1952

By A. E. Boone

"The paper presents critical areas in which improved coordination of effort by industry, government and sup-pliers will be essential to continue the growth record of the Canadian mining industry into the 'seventies'. The analysis includes: exploration, production, mining methods, research and development, markets, management and industrial relations. Performance objectives are suggested where tangible results can be measured. The author suggests the methods by which the 'seventies' can be the greatest decade in the history of Canadian mining. It is indicated that a national mineral policy is essential to the Canadian mineral industry."

Jan 1, 1970

By F. K. McKean

Introduction The present paper may be considered as a sequel to a paper, A Process for Cleaning Molybdenite .Concentrate, which was presented by the author at the annual meeting of the Institute last year. In that paper, a description was given of the laboratory work leading up to the adoption of a new process for treating complex molybdenite ores of the Molybdenite Corporation of Canada. A bare outline of mill performance with the new flow-sheet was included. With this writing, the purpose is to describe the highly interesting work of translating laboratory experience into mill practice, to show what changes were required in design to put the scheme on an operational basis, and to point out the gratifying improvements in mill products which resulted from the new procedure. The process has been placed in operation at the La Corne mine of the Molybdenite Corporation of Canada. This mine was operated during the war by Wartime Metals Corporation, and, earlier, by the Molybdenite Reduction Company, which installed a small plant. The property is situated on the highway from Amos to Val d'Or, Quebec. The claims held by the Company are at the boundary between La Corne and Vassan townships.

Jan 1, 1947

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer's perspective and from an equipment supplier's perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By Rory Cameron, Chuck Edwards

"Stringent environmental performance criteria and regulations, and the desire to minimize water use have made membrane-based treatment and separation processes an attractive option. This has lead to many advances in all aspects of the technology. Membrane separation processes have found application in sea water desalination, brackish water treatment, decontamination of ground water, and wastewater treatment. Development of membranes with better resistance to harsh feed conditions has created new opportunities for the broader application of membrane separation technologies to mineral processing streams. There are examples in mineral processing operations, including treatment of acidic drainage, pre-concentration of pregnant leaching solution in heap leaching operations, separation of acids and metals from waste streams and intermediate process streams, as well as gold and cyanide recovery from a heap leaching operation. This paper provides a brief overview of membrane technology principles, followed by a discussion of current membrane technology applications relevant to the mining and mineral processing industry. The paper further explores the potential for the application of membrane separation as an integrated component in mineral processing operations.INTRODUCTION Increased regulatory pressures, emphasis on water conservation, and scarcity of water in arid regions have resulted in substantial changes in industrial practices in recent years. As a result, many industries have become more open to adopting innovative technologies such as membrane separation. The mining industry, which is typically very conservative, has adopted membrane separation as an effective end-of-pipe solution for effluent and acidic drainage (AD) treatment; however, its use as an integrated component in plant operations has progressed more slowly. With increasingly stringent environmental regulations coupled with the desire for low- and zero-discharge operations, the use of membrane separation technology for achieving acceptable environmental performance may be unavoidable in the future. The relatively small footprint requirement, versatility, and modular construction of membrane separation units facilitate their introduction into existing processes with a suitable feed stream. Membrane separation is not a stand-alone process that provides the ultimate solution to water and wastewater treatment; however, it can often be economically added to conventional waste treatment plants to increase throughput and/or decrease contaminant output (Mortazavi, 2008). Although membrane separation technology has become an established separation technique that is widely used in drinking water production and other industries, it is still considered an emerging technology within the mining and mineral processing industry. This technology offers many potential benefits such as clean water recovery from wastewater, significant reduction of volume requiring conventional treatment, decreased usage of reagents, and acid recovery, all of which lead to increased treatment efficiencies and lower reagent consumption. This could translate to smaller and more efficient plants with lower capital and operating costs and lower environmental impacts. Plant expansion may be facilitated by incorporating a membrane separation unit operation in order to utilize existing treatment systems at higher throughputs."

Jan 1, 2012

By John R. Goode

"This paper reviews options for the separation of a mixture of rare earth elements (REE) into its component elements. Earlier separations used selective chemistry such as double salt precipitation and reductive/oxidative processes – methods that still have a place in the industry. Fractional crystallization was developed for more complete separations of adjacent REE. The latter method was replaced by ion exchange (IX), which was in turn replaced by solvent extraction (SX). Two main SX chemistries are in use, solvation and cation exchangers, with several variants (mixed solvents, ionic liquids, etc.) now under investigation. SX plant configurations have evolved including advanced techniques like “hyperlinking”, novel saponification methods, and alternative stripping techniques. The classic mixer-settler is the most commonly employed device although centrifugal contactors have been pilot-tested. Non-dispersive SX options including microfluidic devices and membrane-assisted SX techniques are being developed and could revolutionize the SX option. Other REE separation techniques now being studied include Molecular Recognition Technology (MRT), Free Flow Electrophoresis (FFE), newer IX systems, and electrolytic processes. Additionally, the classical crystallization and selective precipitation methods and newer bacteria-mediated processes, chloride volatilization, high performance liquid chromatography, and magnetic separation systems have been studied. This paper reviews the options and concludes that conventional SX is the technology of choice but viable alternatives could be demonstrated and acceptable within a couple of years.INTRODUCTIONThe chemical properties of the individual REE are very similar which is why REE minerals and ore deposits almost invariably contain a mixture of all fifteen REE, i.e., La to Lu plus Y. That said, the distribution of REE in a given deposit is frequently dominated by the light REE (LREE, i.e., La to Nd). Examples include the Bayan Obo, Mianning, Lynas Mt. Weld, and Molycorp Mountain Pass deposits where heavy REE (HREE – Sm to Lu and Y) typically account for well under 5% of the REE content. The LREE operations produce some HREE but the main sources of these important elements are the ionic clay deposits of Southern China. Importantly, all of the REE recovery operations referenced above, except for cerianite-bearing ionic clay deposits, initially produce a mixed REE precipitate or calcine with a REE distribution similar to that in the ore (Goode, 2016). However, the consumers of the REE, the manufacturers of magnets, phosphors, catalysts, optical glass, etc., require separated products with purities generally ranging from 99% to as high as 99.9999% depending on the element in question and the end use. Hence there is a need to separate the individual REE one from the other. This paper is intended to review the options."

Jan 1, 2016

By D. S. Case

"Following a brief explanation of the land arrangements under the Alaska Native Claims Settlement Act, this paper will examine both a mineral exploration agreement and a mining development agreement negotiated between two large mining companies and two different Alaska Native institutions. One of the institutions is a village corporation involved with an exploration agreement and the other is one of the Alaska Native regional corporations, which is party to a mining and development agreement with Cominco Alaska for the development of the Red Dog lead and zinc mine.Special attention will be given to the factors to be considered when dealing with small aboriginal owners with few resources in the context of an exploration agreement, including development issues which must be considered early in the process. The paper will also discuss the unique royalty and taxation structures developed for the Red Dog Mine Agreement as well as environmental issues. The paper will also consider the ways in which the cultural and differing economic interests of an aboriginal owner and a large mining company have been accommodated in the both the exploration and development agreements"

Jan 1, 1998

By K. van Warmerdam, M. Pearson, C. Kember, D. McMullen, M. Thayer, C. Ugarenko

In July 2012, Hatch Ltd. and Air Products & Chemicals Inc. completed construction and commissioning of a 4000 tpd O2 cryogenic air separation unit (ASU) for Barrick Gold’s Pueblo Viejo Project located in central Dominican Republic. The ASU produces high pressure gaseous oxygen, which is used for the oxidation of refractory sulphide ore within the pressure oxidation (POX) circuit. As a result of the project’s remote location and tropical climate, many challenges were faced over the course of construction, commissioning and start-up of the ASU. These challenges included adequate preservation of equipment due to dusty and humid site conditions, final assembly and erection of the cryogenic distillation columns on site, limited spare parts inventory/availability, and an unfinished power source for plant commissioning. This paper discusses the steps taken by Hatch and Air Products to successfully design, construct, commission and start up the largest stand-alone ASU plant for a POX application in the metallurgical industry.

Jan 1, 2014

By J-F. Turgeon, Y. Pépin, G. Hudon

The high temperature hydrochloric acid leaching of titanium slag in the QIT upgraded slag process (UGS) creates a harsh environment for materials of construction. Because of their excellent chemical and heat resistance, furan mortars are a key component in the lining system of the UGS pressure leach reactors. Similar products coming from different manufacturers have however shown unequal performances in service. In some cases, cracking of the brick lining has occurred during curing of the mortar. This study was initiated to investigate the impact of the curing conditions on the properties of carbon filled furan mortars. Laboratory tests were conducted to assess the effects of temperature and exposure to water and HCl solutions on mortar shrinkage and mechanical properties (tensile, compressive and bond strength). Three commercial furan mortars that have been used in the UGS leach reactors were thus characterized. Mortar properties were found to vary significantly among the products tested. Moreover, the curing conditions were shown to have a significant impact on mortar shrinkage and mechanical strength. The experimental findings provide explanations for the unequal performances of the mortars in service and for the problems of brick lining cracking that occurred in the UGS leach reactors. This study demonstrates that excessive mortar shrinkage compromises the integrity of a brick lining system.

Jan 1, 2004

By M MacMillan

THE following is a brief description of the method of hoisting ore automatically at the No. 14 shaft of Mcintyre Porcupine Mines, Limited, Schumacher, Ontario. All ore and waste below the 3875-ft. level is hoisted up No. 14 shaft from the 7000-ft. level to the 3000-ft. level. Seventy to seventy-five per cent of the mining is done in this area. The shaft consists of four compartments: a man way, a ventilation compartment and two skip compartments. The hoist, located on the 3500-ft. level (see Figure l), is an 80-in.-diameter, 4-rope friction winder, utilizing two 6-ton front-dump skips in balance. The hoist is powered by a 1,100-h.p. A.C. motor, the maxi-mum speed being 2,400 ft. per minute. The operation can be either manual, push-button automatic from the pocket, or fully automatic. Men can be raised or lowered in the skips, using a collapsible aluminum platform placed inside the skip box.

Jan 1, 1963

By J. E. Nesset, F. Rosenblum, J. A. Finch

"The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to highly reactive and potentially hazardous to both humans and infrastructure. It is essential that there be a reliable test methodology that can measure and categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral mixtures making it difficult to predict their self-heating behaviour a-priori based on mineralogy or with a simple “snapshot” test. Furthermore, self-heating behaviour will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to measure and reliably predict the latent self-heating hazard of a sulphide material. Several of the methods were tested and compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.INTRODUCTION Sulphides as well as other materials (coal, wood chips, hay, powdered milk, to name a few) that are stockpiled in an air atmosphere may undergo oxidation reactions which can result in the evolution of heat (Beever, 1984) (Hudak, 2002) (Blanchard, 2007). If the rate of heat generated exceeds the rate of heat dissipation, the stockpile temperature will rise, potentially leading to “hot spots” in the most reactive areas, and possibly even fires. The heat generation rate, the “self-heating” rate, depends on many factors such as the type and composition of material, particle size, moisture content, oxygen availability, ambient temperature and humidity, and of prime importance, the extend of prior oxidation, or more specifically, the presence of oxidation products. The desire of operators that mine, process or transport sulphide-bearing materials with a potential for self-heating is to have an accepted and reliable method for evaluating and quantifying the potential hazard of their material. The challenges are how to best measure the self-heating properties of given samples, and based on results, predict the behaviour of the bulk material over time and in-situ. Generally, when evaluating a given material one derives the self-heating characteristics of that sample at the time and under the conditions of testing, which will be referred to as a “snapshot test”. If that material is invariable, i.e. it will not change its response over time, then it may be considered to be a “predictive test”. However, if as a result of continuing oxidation or other changes, the material becomes more or less reactive with time, then a “snapshot test” is unreliable with respect to predictive ability."

Jan 1, 2014

By Kristopher John Shelswell

The work in this paper describes the theory, development and analysis of a computer model simulating a mine operation moving material using concurrent decline ramp truck haulage and skipping practices. This simulation was designed specifically to assess the performance of the truck haulage component and to expand on the scope and capabilities of traditional TKM fleet calculations. Haulage fleet simulation results were similar to TKM calculations for the lower to moderate production rate cases. However, comparisons of ramp-up and high production rate scenarios indicated that the simulation model was significantly more sensitive to operating practices and factors not accounted for by calculations derived when using a single TKM figure. Given the proper calibration of inputs and logic, the simulation model was additionally capable of providing information associated with general mine operations efficiency. Further benefits of the simulation model over a TKM approach included logistical assessments such as production schedule feasibility, productivity trade-off quantifications for proposed operating practices, and the validation of mine resource utilization scheduling. The simulation model was able to expand on traditional methods to approach planning and logistics by considering factors such as truck queuing, real-time traffic interactions, random events, and competition for resources on mine productivity.

May 1, 2013

By 12670

The Cigar Lake project will develop the world’s second largest high-grade uranium deposit. The Cigar Lake Phase 1 orebody contains approximately 226 million pounds U3O8 at an average grade of 20.7% U3O8. The mine, to be operated by Cameco Corporation, will use a unique water jet boring mining method to cut previously frozen ore. A distinctive ore handling design is required to handle the highgrade ore slurry exiting the mining machines. The ore will be crushed and ground underground, with the ore slurry then pumped to surface. Loaded into purpose-designed containers on tractor-trailer units, the ore slurry will be trucked to Cogema Resources Incorporated’s McClean Lake mill. McClean Lake will leach all of the ore. Forty-three percent of the resulting uranium solution will remain at McClean Lake for processing into yellowcake. The other 57% of the uranium solution will be shipped to Cameco’s Rabbit Lake mill for processing into yellowcake there. Detailed design for the Cigar Lake project is now underway. Barring regulatory or market delays, production could start up as soon as early 2006.

Jan 1, 2004

By P. D. Waters

"Mineral deposits are where you find them; they have no allegiance to territorial boundaries. Over the past decade much of the new investment in mining has been outside of continental North America, let alone Canada. The larger Canadian Banks have pursued this offshore business through their multi-national organizations; this reflects both the increasingly international orientation of today's business environment, and to a degree, the competitive advantage of these offshore developments.The current oversupply situation in mineral markets and the increasing maturity of the Developed World Economy reduces the need for new mining projects relative to growth' in GNP. Those that are brought on stream in the future due to their competitive advantage, will continue to be pursued by lenders and equity investors alike. IntroductionProspects facing those who search for mineral wealth were described rather well more than 200 years ago by a Scottish professor of moral philosophy, who also happens to be the father of modern economics.In search for new mines, Adam Smith wrote in The Wealth of Nations, ""there seems to be no certain limits either to the possible success or to the possible disappointment of human industry"".How true that statement remains today, where we are seeing economic cyclical problems compounded by basic fundamental structural change within the mining industry.Despite the enormous advances in earth sciences during the past two centuries, the rewards of mineral exploration still remain uncertain. Even though a promising orebody is found, ultimate profitability may still depend on the vagaries of the marketplace, where large and unanticipated changes in supply, demand and prices can play havoc with the best of calculations.The Canadian mining industry has had its share of disappointment during the past few years, with savage competition, shrinking demand, declining prices, and disappearing profits. But it has also had some share of success, such as at Hernlo, which now seems certain to provide some of the lowest cost gold production in the world"

Jan 1, 1986

By Mark McComb, Geoffrey R. Lane

"Over the years many differing approaches have been developed to clearly understand the nature, mode of occurrence, associations and deportment of both free-milling and refractory gold in a wide variety of differing geologic environments and plant products. Many approaches can be taken to characterize the ore which may occur as complex fine grained gold, ultra-fine grained gold, coarse nuggetty gold, complex Asrich refractory gold and double-refractory gold. The approach taken in assessing small drill core composites from Novo Resources Beaton Creek Paleoplacer gold project located in the Pilbara region of Australia was complicated by the nature of the ore, the small amount of sample available from current exploration work, and the gold grade and the grain size distribution. In this case the scope of the study was limited by sample availability although significant amounts of valuable information was also gained. This gold characterization study included the following elements:??Size fraction assays??Ore microscopy??Preparation of heavy mineral concentrates from sized fractions (screening) of crushed or milled head using heavy liquids and Superpan table.??Systematic scans of the heavy mineral concentrate, middling, and tailing fractions using TIMA Automated Scanning Electron Microscopy integrated with an Energy Dispersive Spectrometry to provide semi-quantitative elemental analysis of the individual grains found in the sample.The unique methodology employed to detail the gold deportment was the combination of the Tescan Integrated Mineral Analyser (TIMA) and the Oxford INCA GSR software. This technique not only allowed us to document the deportment of gold but recognize other associated minerals, which included gersdorffite, chalcopyrite, uraninite, coffinite, brannerite and several Rare Earth-bearing minerals.INTRODUCTIONGold deportment studies are commonly carried out on preliminary gold exploration projects in order to determine the various limitations, which may effect processing of the potential ore. This is often because it may be expected that there may be a refractory component to the gold, which may limit physical separation techniques and suggest more costly hydrometallurgical techniques. Often when carrying out gold deportment studies the mineralogical methods may be limited to assuming that the gold will be fine and easily found using standard techniques of optical microscopy or Scanning Electron Microscopy. This may not always be the case as various geological environments may pose their own individual problems to determining the deportment of the gold grains."

Jan 1, 2015

By B. Jago

From the perspective of metallurgical processing, gold ores can be classified into freemilling and refractory ores. Their extractive metallurgy is largely driven by mineralogical factors such as gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals, and invisible gold in sulphide and sulpharsenide minerals. Gold process mineralogy helps address issues and problems related to gold ore processing. It is widely used as a predictive and trouble-shooting tool in gold ore processing, and provides useful information on process selection, flowsheet development, recovery improvement, and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis, and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore.

Jan 1, 2006

By J. Sammut, T. G. Joseph, R. Andreev, M. Curley

"Decisions regarding mining method and subsequent choice of excavator must take into account the quantitative factors of productivity, availability, and capital, operating, and maintenance costs. Dig performance was compared between a hydraulic excavator (HE) and electric rope shovel (RS) of similar size class (i.e., use the same amount of energy to excavate a unit quantity of the same material from a mining face), focusing on the quantitative factors above. Machine performance, normalized to bucket capacity, was assessed as a function of hours of service (60,000 hours per machine). Results showed higher production rates for the HE of similar capacity and age. In general, the RS exhibited lower service cost per volume capacity, though it had higher capital cost. The RS became more cost effective than the HE of similar capacity within approximately 30,000 hours of service. ¦ KEYWORDS Cost, Electric rope shovel (RS), Excavation, Hydraulic excavator (HE), Surface mining RÉSUMÉ Les décisions concernant la méthode minière à adopter et le choix ultérieur d’un engin d’ex¬cavation doivent tenir compte des facteurs quantitatifs de la productivité, de la disponibilité ainsi que des coûts d’investissement, d’exploitation et d’entretien. Cette étude compare les performances en termes d’excavation d’une excavatrice hydraulique et d’une pelle électrique à câbles de même taille (qui utili¬sent par exemple la même quantité d’énergie pour creuser une quantité unitaire du même matériau dans un front de taille), en se concentrant sur les facteurs quantitatifs susmentionnés. La performance de la machine, normalisée à la contenance du godet de volume unitaire, est évaluée en fonction des heures de service (60 000 heures d’activité par machine). Les résultats montrent des taux de production plus élevés pour l’excavatrice hydraulique d’une capacité et d’une ancienneté similaires. De manière générale, la pelle électrique à câbles affiche un coût d’entretien par capacité volumique inférieur, mais son coût d’in¬vestissement est plus élevé. La pelle électrique à câbles devient plus rentable que l’excavatrice hydrau¬lique d’une même capacité au bout d’environ 30 000 heures de fonctionnement. ¦ MOTS CLÉS coût, excavation, excavatrice hydraulique, exploitation à ciel ouvert, pelle électrique à cablesINTRODUCTION The most common excavating tools in surface mining operations are the hydraulic excavator (HE) and electric rope shovel (RS). In general, electric RSs are more reliable and cheaper to maintain (P&H Mining Equipment, 2007), but where complicated geological conditions exist, HEs are preferred because they are generally considered to be more mobile."

Jan 1, 2019

By Gary Anderson

??Privately Held Corporation ??Incorporated in Delaware, May of 2002 ??HQ in Malvern, PA (just outside Philly) ??Approx 40 employees ?9 Field Engineers ?MSHA Certified ?10 Development/NOC Engineers ?Site Survey/Site Design ?RF Engineers ??Standards Based ?IEEE 802.11 ??Commercial Off the Shelf (COTS) ?Gateworks, Ubiquity, Atheros, Linux Based ??Technology was developed and inspired by the lack of communications during the terrorist attacks of Sept. 11, 2001

May 1, 2009

By Marc Legault

The Duparquet mining camp situated along the Quebec segment of the Porcupine-Destor Fault was the site of gold exploitation from 1933 to 1956 and 1988 to 1991. Numerous gold showings and deposits straddle the fault. An ongoing regional metallogenic study by the Quebec Geological Survey has identified five main types of gold mineralization, each showing a distinct style, alteration, control, metal content, and timing. In order to maximise the impact of this study, a 3D regional common-earth-model was constructed along a critical segment of the Porcupine-Destor Fault with the gOcad® technology. The realisation of this model required the maximum use of the public SIGEOM numerical database, as well as the recovery of significant private data from exploration company partners. The 3D model is also a powerful new dynamic exploration tool, which can be queried using geological criteria characteristic of the different gold deposit types. This 3D model can be modified and improved continuously by adding data from new drilling, mapping or geophysical surveys. The case of the Porcupine-Destor Fault illustrates the importance of 3D common-earth-modelling in delivering refined technological geological syntheses likely to attract significant investments from the mining exploration industry, especially for deep exploration programs within mature mining camps.

May 1, 2004