Search Documents

By George Kellock

Introductory The Alberta Provincial Government has contemplated a revision of the Mines Act for some time past, and it is understood that a definite decision has now been made to do this at the next session of the Legislature. The Operators' and Miners' organizations of the Province have been asked, or at least have been given the opportunity, to submit their views and ideas relative to the proposed changes. The operators have already drafted out a number of changes which they feel would improve the Act from the standpoint of safety and practicability, and this paper has been prepared so that the general membership of the Rocky Mountain Branch of the Institute, which is composed largely of the operating and certificated officials of the mines, might have an opportunity to discuss, criticize, and improve upon the suggested changes which the operators are putting forward.

Jan 1, 1929

By H. J. McQueen

Pyro-reduction of ores to metal products developed markedly through the industrial revolution into the great depression. Nineteenth century resource and environmental sustainability were haphazardly improved by many process changes, although the motivation was primarily reduction in labor, feed stocks and fuel. Some notable achievements were coke and hot air for blast furnaces (later from waste heat stoves), puddling of wrought iron and steel ingot production with convertors advancing into oxygen use and continuous slab, billet and strip casting. Although advances in one sector were often counteracted by fall-backs in others, there was progress in that the resource consumption and pollution per unit of production was decreased. Improvements in the 2 decades following WW2 were mixed but popular notice of environmental hazards forced governments to legislate pollution controls and initiate steps in resource conservation. The energy crisis of the 1970’s saw an industrial energy-saving campaign and legislation of technology assessment procedures. Up until mid 18th Century, the training of iron masters depended on apprenticeship with some formalized knowledge from medieval books such as those of Biringuccio (1540) and Agricola (1556). The advances were very slow partly due to absence of scientific concepts of the smelting process. Nevertheless, some iron masters succeeded in improving the process and described procedures to instruct others. With the surge of steam power and the reverberatory puddling process for ductile wrought iron (WI), machinery changed from wood (iron strap reinforced) to WI machinery. With the clarification of the reduction and oxidation mechanisms by Cavendish and Lavoisier (~1780), productivity in iron production surged. The mechanical testing and microscopy of Kirkaldy (1862) spurred understanding of processing and properties of WI and steel. The various forms of C in steels were determined by chemists at the end of the 19th Century. It also became possible to control metal and slag chemistry in the open hearth furnace. But understanding of the transformations during heat treatment of steel only came in the first decades of the 20th Century.

Jan 1, 2012

By Charles Graham

It is the general belief that the coal deposits on Vancouver Island are extremely large, and easily available. Indeed, they are frequently described by prominent public men and by writers in the press as "illimitable" and "inexhaustible." It is well that the facts that have been established as a result of seventy years of surface prospecting, underground operations and extensive diamond-drilling in this coalfield should be disclosed. HISTORY The presence of coal on the coast of British Columbia was first made known by Dr. W. F. Tolmie in 183 5. This coal was brought to him by Indians from the north-east coast of Vancouver Island, probably from Suquash. In 1850 the existence of coal at Nanaimo was announced by Mr. ]. W. MacKay. Development was started in 1852, and coal was shipped before the close of 185 3. The first operations were carried on by the Hudson's Bay Company, who operated the mines until 1861, when they sold them to the Vancouver Coal Mining and Land Company. Practically all of the operations in the immediate vicinity of Nanaimo have been carried on by this Company and its successors. In 1869, Mr. Robert Dunsmuir discovered coal about five miles north-west of Nanaimo, at Wellington. The Welling-ton Colliery Company was organized, and began to produce coal from the Wellington mines in 1871, the coal being shipped from Departure bay. This colliery was a large producer for several years, but was finally closed in 1900.

Jan 1, 1924

The goal of this presentation is to firstly, review mine effluent permits in a number of regulatory jurisdictions; and secondly, to develop a strategy for incorporating the regulatory requirements into the environmental assessment (EA) process for new mine proposals. The focus was on the province of British Columbia (BC) and their recent initiative on the One Project, One Process initiative. This task was approached by reviewing mine effluent permits for various regulatory jurisdictions and comparing them to BC mine effluent permits. This comparison revealed a variety of approaches for designing mine effluent permits, but there is a common scientific approach, which supports the conclusion that the permitting of mine site discharges can be designed based on a scientific approach. This approach is expected to: (a) achieve sound environmental protection, (b) demonstrate the application of Best Achievable Technology, (c) incorporate sound sustainability approaches, (d) incorporate regulatory objectives, and (e) create efficiencies for the regulator and mining industry. There is an essential precursor to developing a sciencebased effluent permit for which the proponent must provide: (1) the necessary technical assessment information to demonstrate the mine effluent permit application will result in an environmentally protective effluent discharge, to the satisfaction of the permitting agency; (2) the necessary level of detail for essential mitigation pollution control works to demonstrate how they will be operated to achieve the necessary treatment goals; (3) the necessary level of detail for non-treatment mitigation (passive treatment, or passive pollution control); and (4) the necessary level of detail to demonstrate how pollutants will be prevented from being mobilized (or being generated) from ore and waste materials, or, if the pollutant originates from an added milling reagent, how the reagent will be reduced. While (active) mitigation pollution control equipment is more definable in an effluent permit, non-treatment mitigation is more nebulous in terms of defining in a mine effluent permit; it is therefore recommended that appropriate management plans be developed for essential mitigation pollution control and non-treatment mitigation (passive treatment) and submitted with the proponent?s EA/effluent permit application packages. Major deficits in adequate active and passive pollution control will inevitably lead to regulatory impediments to developing a permit and allowing a mine to be developed, although EA processes strive to preclude major permit information gaps; the onus is on the proponent to provide complete information in this area. Hence the importance of EA processes ensuring that the major technical information requirements for effluent permit development are included in the EA phase. Recently, this aspect of the mine EA process has taken on a new role under the political efforts of One Project, One Review Process (Canadian) and One Project, One Process (in BC). These initiatives translate, in part, to ?synchronous permitting? (in BC): effluent permitting, for example, may be initiated shortly after the proponent submits the EA application to Ministry of Environment.

Aug 1, 2013

By Rolf Andreas Lauten, Adam Pratomo, Dani Ramdani, Helminton Sitanggang

A universal challenge for the mineral processing industry is the diminishment of high grade ores. Instead, low grade ores, sometimes also containing problematic gangue minerals is the reality. With lower head grades the industry has to put more effort into processing to maintain the output and achieve suitable recoveries. In an effort to reduce the impact of declining head grade, a biopolymer was evaluated as an additive in the gold leaching operation at Antam Pongkor in Indonesia. Laboratory testing revealed that biopolymer usage lead to an increased gold recovery without apparent negative impact on the other parts of the process. Further plant trials revealed both a recovery increase around 1.3% and higher throughput (9%) in the presence of the biopolymer. Some scenarios that can explain these findings will be discussed.

Jan 1, 2014

By Egbert Burchardt

The challenge of "ore bodies getting steadily harder and lower in grade" was brought to light during the first oil crisis in the 70's. Shortly afterwards, HPGRs appeared on the scene with the promise of saving energy. This combined with developments in wear protection for the rolls ushered in a period of trade-off studies that considered the HPGR as an option to improve project economics or to even make projects feasible at all. Since then, applications of HPGRs at Cerro Verde (Freeport), PTFI Grasberg (Freeport), Mogalakwena (Anglo Platinum), Tarkwa (Goldfields), Boddington (Newmont), Penasquito (Goldcorp), and others have contributed to the creation of a formidable basket of operating experience. Collected through years of successful operation, this information has been used to validate design criteria, scale-up factors and establishing a clearer picture of what "to do" and what "not to do". This paper compares results from various mining operations using HPGRs in their processing plants. Some of the lessons learnt in different operating environments are reviewed in order to support proper implementation and operation of HPGR's. Some of the development programs that have been initiated to improve wear life of the tyres and to reduce overall operating costs are reviewed. It is timely to summarize today?s experience and analyse its implications for existing and new operations.

Jan 1, 2012

By F. Barriga-Ordonez, J. A. Finch, L. Calzado, S. R. (Ram) Rao

Sludge, formed by lime treatment of acidic drainage and stored in tailing ponds of the Sudbury region, contains 5-7% Ni, mostly in a mix of hydroxides with Fe (~ 10%), Mg (~ 10%) and Cu (-0.5%), and Ca (-3.5%) as sulphate. Investigations were conducted to recover nickel by a 2-stage process. In the first stage, the sludge was leached with sulphuric acid at pH 3.2. About 90% of the nickel was extracted, producing a solution, which contained mainly nickel (2 g/L) and magnesium (3.7 g/L). In the second stage, nickel was separated by treating with ozone which recovered 99% of the nickel in the Ni(III) oxidation state as -85% pure nickel oxide-hydroxide (NiOOH) precipitate. The oxide settled and filtered readily. A potential use of the product in battery making is suggested. The leach residue contained 0.5% Ni making it less toxic for disposal. Some physical properties of nickel oxy-hydroxide and process parameters including ozone consumption will be discussed.

Jan 1, 2005

By Minghao Hu, Hongbo Zhao, Jun Wang, Wenqing Qin, Rui Liao, Central South University

"In the present work, X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS) analysis and electrochemical analysis were carried out to investigate the intermediate species and electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms. For bioleaching of chalcopyrite by the sulfur oxidizing microorganism Acidithiobacillus caldus, the redox potential was always lower than the appropriate value and chalcopyrite was mainly directly oxidized to polysulfide (Sn 2-), thus resulting in low copper extraction. As for bioleaching of chalcopyrite by the iron oxidizing microorganism Leptospirillum ferriphilum, chalcopyrite was mainly directly oxidized to polysulfide at the initial stage where redox potential was lower than the appropriate value and resulted in low dissolution rate. At the middle stage where redox potential was appropriate (about 350–480 mV vs. Ag/AgCl), chalcopyrite was mainly transformed to intermediate species of Cu2S rather than polysulfide, thus resulting in high dissolution rate. At the later stage where redox potential was higher than the appropriate value, chalcopyrite was mainly directly oxidized to polysulfide which caused the later passivation of chalcopyrite. Finally, a model of electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms was provided.INTRODUCTIONBiohydrometallurgy is considered as one promising mineral processing technique in processing low grade ores due to the advantages of simplicity, low cost and eco-friendly. Chalcopyrite (CuFeS2) is the most abundant copper-bearing resource, accounting for appropriately 70% of the known reserves in the world, while is recalcitrant to bio-hydrometallurgy mainly due to the coated passivation layer (Klauber, 2008; Li, Kawashima, Li, Chandra, & Gerson, 2013). However, the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching are still uncertain. The microorganisms assisting chalcopyrite dissolution can be mainly classified into three types, including mesophilic microorganisms (e.g., Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans), moderately thermophilic microorganisms (e.g., Acidithiobacillus caldus, Sulfobacillus thermosulfidooxidans and Leptospirillum ferriphilum), and extremely thermophilic microorganisms (e.g., Metallosphaera sedula, Sulfolobus sp., Acidianus sp., and Sulfurcoccus mirabilis). Moderately thermophilic microorganisms have a better prospect in the future industrial application of chalcopyrite bio-hydrometallurgy (Olson, Brierley, & Brierley, 2003; Rohwerder, Gehrke, Kinzler, & Sand, 2003). Hence, investigating the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching by moderately thermophilic microorganisms is of important significance, which will provide essential information for promoting chalcopyrite bioleaching by moderately thermophilic microorganisms in laboratory or industrial plant."

Jan 1, 2016

By J A. Gilliand

Mineralogical cross sections of orebodies on the 300-,600- and 900-foot levels of the Coronation mine have been interpreted in terms of centers of mineralization. The maximum concentration of chalcopyrite occurs closest to these centers, with pyrite and pyrrhotite concentrated some distance away. The magnetite concentrations are farthest removed from the centers. A hydrous halide fluid model is established. Attempts to explain the observed mineralogy by the action of temperature gradients on the fluid model were unsuccessful. Likewise, the action of diffusion alone on the fluid model cannot explain the observed mineral distribution. The concept of attenuation is introduced-i.e., the rate of diffusion of a particle species is related to the product r2 I/ M, the attenuation coefficient, where r is the particle radius and M its molecular weight. Attenuation, acting on the fluid model alone, will not produce the observed mineral distribution, but, when considered together with the action of temperature gradients, the observed mineralogy can be well explained by the combined effects of these two processes on the assumed fluid model.

Jan 1, 1965

By A Frydrychewicz, J. Mirza, J. Lipkowski

The objective of this work was to understand the mechanisms of action of additives, such as thiourea, that enhance gold leaching in thiosulfate solution. The leaching reaction and surface passivation were investigated using linear sweep voltammetry. Leaching currents were determined using analysis of current-potential curves and the mixed potential theory. The gold-electrolyte interface was further characterized with surface enhanced Raman spectroscopy. The results show how thiourea prevents formation of oxysulfur compounds, which passivate the gold surface. Other molecules such as 3- m ercaptopropionic acid and L-cysteine were also studied as possible additives to prevent passive layer formation.

Jan 1, 2011

By D. Hu, L. Matzar, J. Hampton, M. Gutierrez

Nanodarcy permeability is common in many oil- and gas-bearing formations requiring unconventional stimulation technologies, such as hydraulic fracturing (HF), which can connect the isolated hydrocarbon-rich pores with a wellbore through induced fracture networks. Even though a dense induced fracture network is capable of accessing economic amounts of hydrocarbons, much of the rock between and very close to the fracture network is still un-accessed and contains extremely low permeability. Inducing fracture networks into brittle rock can create large amounts of micro failures in surrounding regions that are not connected to the wellbore, as can be seen in Fig. 1(a) from the very wide acoustic emissions (AEs) cloud associated with a narrow fracture generation. It is possible in certain types of rock to increase the effective matrix permeability in localized regions based on the damage associated with the surrounding hydraulic fractures and subsequent high stress concentrations along localized pre-existing potential failure zones. To study this problem, laboratory HF tests were performed at true-triaxial stress state in brittle crystalline rock while monitoring AEs. The AE associated with HF was analyzed for source parameters using the moment tensor inversion method called Simplified Green’s Functions for Moment Tensor Analysis (SiGMA). Using the moment tensor for each individual AE event, the mode of failure was determined. Crack slip directions and crack face normal directions were also found, along with the relative volume of individual micro failures as well as a damage parameter. The associated source parameters were used to classify differing regions of damage in the sample induced from HF and correlate these regions of differing damage to the effective drainage region. Shown in Fig. 1(b) is a near-wellbore (NWB) region that contained three times larger average relative volumetric deformation of individual tensile AE events than the average tensile AE event volume from the entire sample. Because of the large difference in micro fracture volumetric deformation for the NWB region compared to the entire sample, predictions of HF induced damage must be included in reservoir drainage predictions.

Jan 1, 2015

By M. Staite

This paper analyzed the feasibility of converting a 5kW natural gas SOFC power generator system designed to operate on natural gas to be fuelled by methanol. The analysis included laboratory methanol fuel processing experimentation, methanol reformate SOFC cell testing, and SOFC system mass and energy balance modelling. Methanol fuel processing experimentation indicated that theoretical reformate compositions can be achieved for high temperature (600-900°C) methanol steam reforming. A 6% open circuit voltage decrease and a 10% peak power current density decrease between cell operation on humidified hydrogen and methanol reformate was observed. SOFC system mass and energy balance modelling indicated that a natural gas SOFC system can be converted to operate on methanol fuel with minimal (1%) efficiency impacts, however the systems' thermal integration can be impacted.

Jan 1, 2005

By K. D. Peaslee

Slag splashing is an important development that has dramatically improved BOF vessel campaign life and reduced operating costs. This paper highlights research from physical modeling work using a 1/8-scale room temperature model BOF and slag characterization studies from several plants in North America and China. In the model studies, gas flow rate during blow and viscosity of the liquid were found to be two of the most important factors to changing the overall rate of liquid splashed onto the vessel sidewalls. When the flow rate was increased or viscosity decreased, the lower regions of the walls were splashed at a much greater rate. It was also shown that by changing the lance height, more liquid was deposited in the upper regions of the vessel at the expense of lower regions. Reducing the number of nozzles was found to be the most effective method of selectively coating a particular vertical section of the wall. Studies of BOF's using slag splashing in North America and China showed a difference in the melting characteristics of the final slag. Generally, slag splashing is successful when the melting point of the slag is 220-270°C below the tap temperature to maintain a balance between fluidity and refractoriness.

Jan 1, 2004

By Fr. -W. Bach

In the past years the enormous weight saving potential of magnesium sheet has been demonstrated by various research projects all over the world. It has been shown magnesium flat products can benefit automotive, aviation, machine tool and consumer electronics industries. Major material problems such as poor formability, corrosion resistance and high production cost still inhibit the application of magnesium sheets in large scale production. The present contribution outlines achievements in casting and rolling technology. The authors developed an adapted strip casting process in which near-net-shape rolling feedstock of several wrought alloys has been produced. During the rolling process, various parameters were varied in order to modify the microstructure and surface quality of sheet. Several temperature cycles, strains, lubricants, roll surface structures and roll coatings have been analyzed. The sheets were examined and tested in deep-drawing experiments. Suitable rolling schedules have been developed for standard and modified wrought alloys. The study concludes with an overview of current industrial solutions and an estimation of the potential cost savings that might result from the adaptation of the process that has been developed.

Jan 1, 2006

Applying DEM to prediction of tumbling mill performance is challenging because several different modes of breakage are active in the process. As our knowledge of breakage and computational capacity improve, it is worth revisiting previous simulation tasks which did not produce a satisfactorily realistic description of a measured process. At SAG 2006, we reported the simulated and measured outcomes of treating a well characterised ore in a 1.2 m diameter mill. This well instrumented, pilot scale mill at the University of KwaZulu-Natal has been combined with some new approaches to ore testing to allow different modes of breakage to be tested. The mill design allows the rate of generation of fine material to be measured in close to real time for autogenous and SAG mill charges. The updated simulation model estimates mass loss with particle evolution and embeds the cumulative damage and breakage. The simulated results are compared with the measured results. Issues such as relating modelling inputs to particle breakage characterisation data and the accuracy of the predictions of the models are discussed.

Jan 1, 2012

By D. Song

In this paper, the differential equations governing the mass transport and the electrochemical reaction in a cathode catalyst layer of polymer electrolyte membrane fuel cells are solved based on the polynomial series expansion method. Explicit expressions for the polarization curve as well as for the distributions of oxygen, current density and overpotential are obtained when a quadratic, cubic or quartic polynomial is employed to approximate the oxygen concentration distribution. These kinds of explicit solutions are desirable for MEA design and diagnosis purposes. The comparison between the conventional numerical approach and the explicit solution approach proposed here shows that satisfactory accuracy can be reached by the first four terms of the polynomial series. The effect of the catalyst layer thickness on the accuracy of the obtained explicit polynomial solutions is also discussed.

Jan 1, 2005

By R. Plassart, F. Laigle

"As a powerhouse, a transformer or a valve chamber, large underground caverns are a major element of hydropower plant. On the contrary to galleries and shafts which are linear and long underground structures, large caverns are designed with often complex geometries and large spans. Moreover, as these caverns are generally located on the foot of the hydraulic scheme, the high overburden is often responsible of a high stress state. Thanks to current experiences in France and around the world, the Hydro Engineering Centre (CIH) of EDF has defined great principles in the design of caverns leading to a more general methodology. The project of Tehri in India is an example of difficult ground, with in the same time a high overburden, a ductile material and an important schistosity. These physical realities are attempted to be approached in numerical modelling thanks to a constitutive law with softening behaviour and an oriented criterion integrated in the continuum model. As a result, a flexible support is advised, based on a high density bolt system and a thin lay of shotcrete. This methodology has been developed in the case of Gilboa in Israel, except the schistosity which has not been observed in situ. At last, the example of Gavet (France) illustrates a discontinuous case of numerical modelling for a good quality but fractured rock mass.PRINCIPES ET METHODES DE CONCEPTION DE GRANDES CAVERNESHYDROELECTRIQUES SOUTERRAINESRESUME Les grandes cavernes souterraines abritant les turbines, les transformateurs et certaines vannes sont des ouvrages majeurs dans les aménagements hydroélectriques. A la différence des galeries et des puits qui présentent de longs linéaires, les grandes cavernes sont des structures à la géométrie souvent complexe et avec des portées conséquentes. De plus, ces cavernes étant généralement situées en pied du circuit hydraulique, la grande couverture rocheuse peut se traduire par un état de contraintes important. Forte de ses expériences récentes en France et dans le monde, le Centre d’Ingénierie Hydraulique d’EDF a identifié de grands principes de conception des cavernes permettant l’élaboration d’une méthodologie plus générale. Le projet de Tehri en Inde est un exemple de terrain difficile, présentant à la fois une forte couverture, un matériau ductile et une schistosité marquée. Ces réalités physiques sont approchées au mieux grâce à la prise en compte dans les modélisations numériques d’une loi de comportement radoucissante avec un critère orienté intégré dans un modèle continu. Les résultats ont conduit à privilégier un soutènement souple basé sur un boulonnage systématique relativement dense associé à une fine couche de béton projeté. Cette méthodologie a ensuite été reprise pour le projet de Gilboa en Israël, exception faite de la schistosité puisque non observée sur site. L’exemple de Gavet (France) enfin permet d’illustrer un cas de modélisation numérique discontinue d’un massif rocheux de bonne qualité mais fracturé."

Jan 1, 2015

By M. Kamyab

Transportation of fluid and slurry (fluid and solid particle mixtures) in a pipe and annulus space has been the focus of numerous studies. There are different parameters to be considered when studying slurry transportation. These include slurry velocity or flow rates; fluid properties such as density and rheology; and solid particle properties including concentration, density, shape and size. Also the angle of the flow conduit, rotation of the pipe and possible eccentricity of the annulus are other factors which influence slurry transport characteristics. Although a number of analytical, numerical and empirical equations as well as numerical simulations have been developed for studying the flow and slurry transport characteristics, the results need to be validated against either field or lab data. As performing field tests is costly and time consuming, conducting simulations at the laboratory scale appears as a good alternative. Different flow loops have been designed to study slurry transport behaviour in different science and engineering disciplines including oil and gas and mining. However, few of these consider, in particular, cuttings transportation in small size annulus space. The flow characteristics appear to be very different when slurry travels within a small size annulus, in particular when the fluid velocity is high. In this study, a review of some of the existing slurry flow loops will be conducted. Then the details of a slurry loop, which has been designed and commissioned for the purpose of studying cuttings transport in a small size annulus space for applications in drilling mineral exploration wells using coil tube technology, will be presented.

Aug 1, 2013

Up to thirty years ago, coal preparation in western Canada, except at four plants, had not included actual coal washing. The exceptions were at Nanaimo and Royston, B.C., where tub washers and wet tables were in use; at Hosmer, B.C., using. Robinson cones; and at Leitch Collieries, Passburg, Alta., using a feldspar jig. The two last named collieries had a short life and were not operating in 1920. The industry was divided, as at the present day, into two sections, steam (bituminous) coal and domestic (largely sub-bituminous) coal, the first generally supplying industrial needs and the second householcl and other heating requirements. The two sections overlap to some small degree today as prepared sizes, chiefly stoker, and briquettes, from steam coal are shipped for house-hold use, and domestic slacks are used in certain industrial plants. The .domestic operator, for reasons shown later, was not primarily concerned with actual coal washing as a phase of coal preparation, and bent his efforts to improvement of screening and loading plants, with hand-picking of coarse sizes. The bituminous operator, on the other hand, felt it necessary by 1920 to consider coal washing. When the mines were comparatively young, coal quality could be controlled to a considerable degree by selective mining, by leaving behind some of the seam or by-passing districts in a mine where the coal was of inferior quality to that in other districts. This obviously had its limitations, and so the next step was coal washing.

Jan 1, 1952

By S. K. Sharma, Sanket Bacchuwar, Prabal Kumar Agrwal, G. V. Rao

"Iron ore processing industries play a vital role in the Indian economy. At present Iron ore of around +64% Fe is used for production of Iron through blast furnace. To produce +64% Fe from low/medium grade ores, crushing & beneficiation is compulsory. But during these processes, large amount of slime is generated. It is estimated that 18% -25% of tailing is generated during the processing of iron ore. The iron ore slime is discarded because of its particle size and chemical composition not being suitable as feed to the blast furnace. Although the fines/slimes can be agglomerated to larger particle, the alumina to silica ratio which is normally more than one pose serious problem during sintering process and subsequent smelting in blast furnace. The alumina content in the slime needs to be reduced for it to be used as the feed for blast furnace. The sample assayed 61.40% Fe, 7.68% SiO2, and 1.52% Al2O3, LOI 2.63% and all other elements were found in critical limit. A series of 27 tests were conducted by using a spiral for optimisation of process parameters to produce a pellet grade concentrate from the stacked slimes obtained from Kirandul. This paper deals with the optimisation studies of various parameters of a spiral concentrator and helps to utilize the fines from tailing ponds.INTRODUCTIONReserves of high-grade iron ores are diminishing all over the world at an alarming rate. As a result, alternative ways of augmenting and conserving precious and non - renewable natural resources are being seriously considered. One such attractive option is the recovery of metal values from slimes / tailings. Iron ore tailings containing around 48 - 60% Fe are generated from the iron ore washing plants and are disposed into tailing ponds without any further utility. These tailings in the form of slimes are not suitable in iron and steel making due to the presence of higher amount of gangue constituents. Several beneficiation techniques have been tried from time to time to reduce the gangue so that the beneficiated products could be effectively used."

Jan 1, 2016