Search Documents

By I. M. Gordon, J. Blackshaw

"Run-of-mine ore is reduced to 4 per cent on 4 mesh (3/ 16 inch), using four stages of dry crushing. The mill feed is then reduced to 2 per cent on 48 mesh and 60 per cent through 200 mesh, using one stage of ball milling in cyanide solution. During the subsequent treatment about one-tenth of the tonnage is removed as a table concentrate and ground to 77 per cent through 325 mesh. The size of the mill tailing is 66 per cent through 200 mesh.Four stages of ore reduction began when the dry crushing plant at No. 26 Shaft came into operation at a maximum rate of 440 tons an hour on July 31, 1941. A detailed description of the crushing plant was published in C .I .M. Trans., Vol. LVI, 1953.One-stage ball milling in cyanide solution came into full operation on January 11, 1938. The ball milling plant had a capacity of 4800 tons daily when reducing mill feed at 2. 7 per cent on 1/ 4 inch to 54. 3 per cent through 200 mesh. Primary grinding to 60 per cent through 200 mesh commenced May 22, 1945, when the feed was 3 per cent on 4 mesh. Under these conditions the capacity of the ball milling plant is estimated at 4300 tons daily. A description of the 11 Hollinger Crushing and Grinding Plant"" by D. C. McLaren was published in the Canadian Mining Journal, June 1944.The concentrate grinding circuit using a 7 x 15 low discharge ball mill and a 19-foot diameter bowl classifier with a 6-inch centrifugal pump to close the circuit began operating in the ball milling plant on October 24, 1939."

Jan 1, 1965

By Zhao-shu Sun, Mao-lin Li, Rui Cui

"Fankou Mine produced pyrite concentrate (PC) from the tailings by rougher and scavenger flotation before 2010, with the averaged S grade of 40.54% at recovery of 79.34%. The economic value of PC increases with its purity. When the S grade of PC feed to sulfuric acid plant is over 47%, the pyrite cinder can reach a high Fe grade of 62% which can be directly sold as iron concentrate. On this background, engineers in Fankou Mine set the PC with S grade of 47% as target.The direct way to reach that goal was to clean the rough PC Lots of cleaner flotation tests were conducted and the balanced strategy was to produce two ranks PC with the S grade of 47% and 38% at the recovery of 44.20% and 36.17%, respectively. The dual-product flowsheet was successfully industrialized in 2010. In order to further improve the quality of PC, gravity separation was introduced into the flowsheet. The numerical simulation and tests were performed to evaluate the beneficiation and classification performance of hydrocyclone as it treated the rough PC. It was shown that the underflow of hydrocyclone could addressed the S grade of 47%, and the finer size overflow could also be enriched to PC with S grade of 47% by flotation, due to the contained pyrite with well liberation. That is to say, with the ingenious addition of hydrocyclone to treat the rough PC, single PC with S grade of 47% could be achieved. The new flotation-gravity separation flowsheet was commissioned to produce the high quality PC at the end of 2013. The averaged S grade is 47.20% at recovery of 82.26% in 2014. The two steps flowsheet improvement maximizes the enterprise benefits and leads to simple utilization of Fe in pyrite in downstream industry."

Jan 1, 2016

By Robert B. Parsons

"For the fourth time in five years, residents of northern Canada have seen a change in the tax treatment of housing and travel costs. The latest changes announced in December 1990 by the Minister of Finance are to become effective in 1991. When will the tinkering stop?IntroductionFor man y years prior to 1987, certain travel and housing allowances received by employees in remote areas were generally considered by Revenue Canada to be tax-free, even though some observers suspected that such generous treatment was contrary to the provisions of the tax legislation. In the mid-eighties, Revenue Canada decided to reconsider the tax treatment of the mining industry's long standing practice of providing housing and travel assistance to these employees. The tax- free treatment was continued by virtue of annual remission orders, but only pending the enactment of legislation which would tackle the issue head-on and layout the rules in black and white to be seen by all. The sequence of events since then may be chronicled as follows:February 26, 1986-Finance Minister Wilson's budget present s the framework for the future tax treatment of travel and housing benefits provided to residents in remote regions of Canada.December 22, 1986-The Minister of Finance announces detailed rules to fill in the earlier announced framework.January 1, 1987-The new tax rules come into effect.April 29, 1988-The Minister of Finance announces the establishment of a Task Force to examine the existing criteria for determining the eligibility of residents of northern and isolated areas for tax benefits.October 27, 1989-The Task Force presents its report.December 7, 1990-Finance Minister Wilson announces a new system of tax benefits for residents of Canada's northern and isolatedregions.January 1, 1991-The new rules become effective."

Jan 1, 1991

By K. H. March

In the present very highly competitive condition of the bituminous coal business, it is becoming increasingly apparent that coal mines which do not lend themselves to efficient mechanization cannot long survive. It would seem that those mining operations best fitted to survive the struggle for existence are burdened with the considerable capital and maintenance cast of carefully selected mechanical and electrical mining equipment. The ever changing conditions of coal mine operations require equipment which is adaptable to a variety of uses; and investigation of the mechanical and electrical equipment in most mines will show that the operating duty of much of this equipment is considerably different from that duty for which it was originally selected. And it would appear that one of the essential qualifications for a successful mine management is a marked ability to get satisfactory operating results from equipment which has been transferred from some other operation, rebuilt, rearranged, or in some way adapted to the job at hand. As a striking example of such mechanical ingenuity, many of us recall that the first longwall jigging conveyor used in Nova Scotia was built in Sydney Mines from odds and ends in the scrap pile at a total cost of less than $50.

Jan 1, 1930

By T. Abu Leil

A new class of ternary Mg-Sn-Ca alloys is being developed to address the dual demands of corrosion and creep resistance at service temperatures. While tin has proven to enhance the corrosion resistance, calcium is expected to significantly increase their creep resistance of binary magnesium alloys. Their effects in ternary magnesium alloys are not yet known. The series of alloys studied has Sn and Ca in the ranges 3-6% and 1¬2%, respectively. The results indicate that these alloys have two-phase structures with CaMgSn phase dispersed in a matrix that is predominantly a solid solution of magnesium. The corrosion behavior of these alloys has been investigated by means of salt spray tests and potentio-dynamic measurements. Creep behavior of these alloys was measured at a temperature of 135 C under an applied compressive stress of 85 MPa. Scanning Electron Microscopy with Energy Dispersive X-ray facility and X-ray Diffraction techniques were used to characterize the microstructures. The results indicate the prospect of designing alloys that can provide optimum combinations of corrosion and creep resistance by adjusting the relative compositions of Sn and Ca in the system.

Jan 1, 2006

By J. B. McKenzie

Since connnencing underground prcxiuction in 1979, the Ruttan Mine has been prone to secon:iacy sulphide dust explosions. Al though infrequent during the early years of prcxiuction, these occurrences did result in major damage and lost time injuries. 'As the mine exparrled and developed to further depths, sulphide dust explosions occurred on a more frequent basis. Incomplete ventilation se:rvices, required to exhaust the affected areas, caused frequent delays resulting in lower prcxiuction rates due to the time required to ventilate the affected areas of the mine. CUrrent procedures to minimize the effects of secon:iacy dust explosions evolved from practical suggestions arrl examining methcx:ls other mines have developed to cope with the problem. Procedures and regulations to protect errployees from exposure to hazards of sulphur dioxide are time consuming, expensive and counter prcxiuctive in their present fonn. This paper describes the history of secon:iacy sulphide dust explosions at the Ruttan Mine and the methcx:ls and proced.ures currently in place to minimize and contain the effects of dust explosions.

May 11, 1988

By M. Romana

"RMR geomechanics classification is being used all over the World as a useful tool for tunnel predesign and construction. Bieniawski (1989) provided guidelines for tunnel excavation and support, according RMR numerical values; guidelines which are now included in almost all tunnelling books, regulations, and Internet portals. But in the last 25 years tunnelling techniques have changed and some of the guidelines have become obsolete.. The conditions of tunnels for the 1989 guidelines application were: horseshoe shape; 10 m width; vertical stress < 25MPa; construction by drilling and blasting. Actually a substantial number of tunnels are mechanically excavated. The tunnel themselves are now bigger: a span of 14 m. is very common for transportation tunnels. The guidelines included the following concepts: excavation method, rock bolts (20 mm diameter, fully grouted), shotcrete, steel sets. There is an increasing gap between the 1989 guidelines and the practice: in many tunnels different to-the-case excavation and support requirements are established. Bieniawski himself has published a paper (Lowson & Bieniawski, 2013) with different guidelines based in Lowson’s practice, with no explanations and/or justification.In this paper a new set of RMR tunnelling guidelines is proposed taking account of the actual industry conditions, and increased safety regulations. The 5 classes’ limit RMR:values (80,60,40,20) are no more useful actually: Values of RMR (70, 50, 30) are used in practice to define quite different tunnelling techniques. Consequently a 10 subclasses system is proposed. Each subclass covers a span of 10 RMR points. As the number of mechanically excavated tunnels has increased a new correction factor is necessary, according the excavation method.The proposed 2014 RMR guidelines are for tunnels 10 to 14 meters wide, the world practice for new roads/railways tunnels. Many tunnels for water/ services are smaller with smaller support needs. Wider than 16 m caverns are out of the RMR system.It is not possible, nor desirable, to propose only a value for support in each subclass. The new guidelines propose an interval of values for certain types of support. More pessimistic values must be chosen for wider tunnels, tunnels with lower RMR values in each class and cases when a higher safety factor is asked for. More optimist ones are chosen for narrower tunnels, and higher RMR values. Some alternatives are almost complementary, others are contradictory. Sometimes several different techniques are proposed Guidelines are not automatic options. Good engineering judgment must be used when choosing between the different alternatives. Guidelines are not mandatory suggestions."

Jan 1, 2015

By D. W. McDonald

Coal mining and railway transportation are so closely en-twined and so dependent one upon the other that the failure of one would mean the total collapse of the other. With this indisputable fact in mind, there is no doubt that the operator of each is deeply interested in the other&apos;s success. Railway transportation began at the mouth of a coal mine. The first railway car was the English coal-wagon, a crude box on four wooden trowlets, running on wooden rails and holding 1,600 pounds. This was operated by gravity or horse-power in England to convey coal from the mines to the rivers. The first coal-cars used on Nova Scotia railways were of 4 tons capacity with side doors and "V" shaped centres. Then followed flat-bottom, 4-ton cars that operated on tipples, the car bei.ng held in tipple by a chain passing over the top and fastened on either side. Next came the 6-ton car with drop-bottoms, then the 10, 15, 30-ton cars, and now the modern 50 and 100-ton steel cars, equipped with automatic couplers, brakes, and rachet dumping device. Contrast the first coal-car with a modern luxurious pull-man or a I 00-ton coal and ore car, and you have a record of progress in railway transportation. The development of the steam locomotive was no doubt the greatest factor in this progress, but let us not forget that the foundation of all industrial development was and is coal. and that development in mining and railway transportation should keep abreast.

Jan 1, 1924

By Balmer Neilly

To one with so little experience in matters pertaining to currency, international finance, and foreign trade, this is surely an ambitions venture on my part. However, this is a subject of prime importance to all seriously minded Canadians and, if we are to obtain any clear understanding of the factors involved, we must study the facts and debate such points as may remain at issue. During the last few years, the world&apos; s better known economists have described the gold standard in all its ramifications and in such detail as to leave many of us even more confused than before. If we, then, are to acquire any real conception of its meaning and use, I think we must reduce it to its fundamentals and start from there. To my way of thinking, gold in ? trade and commerce is the symbol of honesty. When you seek to discharge a debt by tendering paper you hand the recipient an I.O.U. which may or may not be good, for the purchase of goods or services to the extent of its face value. When, however, you discharge a debt by the payment of gold, it constitutes a complete and final discharge. There are no reservations - no ifs and ands - and the transaction is definitely closed to the satisfaction of all concerned. Gold, then, is evidence of accumulated and transferable wealth that is immediately acceptable in practically every part of the world. However, there is not nearly enough gold to meet the demands of world trade, and. many years ago this deficiency gave rise to what we now describe as our banking system.

Jan 1, 1949

By M. Boussuge

Ceramics and refractories have many common constituents and consecutively exhibit several analogous properties. For example, concerning the thermomechanical properties this paper will focus on, the type of creep that can be observed in both materials is often the same (kinematic hardening). Changes in microstructure (phase transformation, dehydration, sintering, crystallisation,...), induced by heating and/or cooling, can also drastically modify the mechanical behaviour of ceramics and refractories. But the coarse granulates, the porosity and the impurities contained in industrial refractories may lead to specific responses of this material to thermal and/or mechanical loadings. In particular, some differences can be observed with technical ceramics in the main type of damage observed in service : diffuse damage in refractories (microcracking) and localised damage in ceramics (macrocracking). In this paper, the possibilities of transferring a part of knowledge from ceramics to refractories will be discussed, in the field of thermomechanical properties : experimental characterization techniques, mechanical behaviour models. Finally, some problems caused by scale effects and by the integration of thermomechanical properties of refractories in the numerical simulation of industrial structures will be evoked.

Jan 1, 2004

By C. Phan

This paper outlines opportunities provided for enhanced management and process control by ISA PROCESSTM technology. ISA PROCESSTM technology has the core advantage of offering the potential for vastly improved electrode handling systems. This fundamental characteristic has enabled ISA PROCESSTM technology to develop management and process control systems that are modular, minimalist in their complexity and tailored to a tankhouse operating environment. A review will be presented on the current status of management and process control in ISA PROCESSTM tankhouses covering the central issue of electrode handling as well as electrolyte circulation systems, voltage monitoring, cathode plate tracking, and product tracking. Particular reference will be made of the recent development by Xstrata Technology (XT) and their technology partners, VRT Systems, of an Radio Frequency Identification (RFID) based solution for tracking ISA PROCESSTM cathode plates. The system encompasses fixed readers which identify plates passing through the stripping machines and the use of sophisticated tracking and database software enabling the development of cathode asset management and operational strategies. The performance of individual plates and batches of plates can be tracked through a full service history.

Jan 1, 2007

By K. Morikawa, K. Asano, J. Yoshitomi

The quality requirements for ladle shrouds have become stricter year by year to the pursuit of higher productivity and improved quality in the continuous casting of steel. The ladle shrouds must be sufficiently durable under severe conditions, such as operation without preheating and during several sequential castings. The consideration is that ceramic fibres, which have been applied in shrouds for thermal insulation during casting, could pose a risk to the worker&apos;s health. We realized materials for the ladle shrouds which show high strength and low elasticity. At the same time pursuing effective insulation, a coating which contains no fibres (Foaming Coat) has been developed, replacing the conventional one containing fibres. These materials are durable under conditions of repetitive use and consequently satisfy the customer&apos;s demands. The ladle shrouds which were improved in this way have achieved an excellent durable life in hot service of three times that of conventional ones. This paper reports the recent technological developments in ladle shrouds as well as their performance under hot operating conditions.

Jan 1, 2004

By Mary Jean Buchanan

The last twenty years have seen the advent of environmental concerns and sustainable development, and the industry has witnessed the rise of Environmental Management Systems and their registration through several international standardization systems such as EMAS and ISO 14001. Beyond EMS and ISO 14001, which new goal the mining industry should aim at. Life-cycle assessment (LCA), another tool from the Environmental Management System series, is also on the rise and currently the object of an international standard (ISO 14040:1997). Through LCA, it is possible to assess the environmental aspects and potential impacts associated with products and services, taking into account all the activities required for its fabrication, its use, its transportation and its disposal. How could LCA be applied to the mining industry ? Is the international market pressurizing on mining companies to supply an ?environmental ore?? What about the automobile industry and its use of LCA ? Will it influence the ferrous and non-ferrous metal industry, suppliers of raw materials ? This paper presents a review of possible applications of LCA for the mining industry as well as world trends.

May 1, 2001

By D. H. C. Wilton, W. A. Sears

"Abstract-The 682.8 ± 1.6 Ma Tickle Point Group consists mainly of rhyolite flows and tuffs with- in the Avalon Zone of the Appalachian Orogen in Newfoundland. Stratabound massive sulfide mineralization, consisting of pyrite, sphalerite, chalcopyrite and galena, occurs at the Winter Hill prospect, where a lower pyritic, Cu-rich zone and an upper Zn-Pb-rich zone are hosted by a carbonate-calc-silicate lens. At the Frenchman Head prospect, stringers of pyrite, minor sphalerite, chalcopyrite and rare galena are hosted by felsic volcanic rocks of the Tickle Point Group .Base metal ratios, metal zonations and the overall stratigraphic framework suggest that these sulfide occurrences represent volcanogenic massive to semi-massive sulfide mineralization (stringer type at Frenchman Head). As such these prospects represent the only known VMS occurrences within the Avalon Zone of Newfoundland. Pb isotope data indicate that galena from the Winter Hill prospect is less radiogenic and older than galena from Dunnage Zone occurrences, and suggest that the Winter Hill mineralization formed in an environment tectonically distinct (exotic) from the Dunnage Zone."

Jan 1, 1996

By A. R. Sorta, D. C. Sego

ABSTRACT Temperature, solute, texture, and thixotropic effects on time domain reflectometry (TDR) measurements of water content in oil sands tailings are investigated. Results indicate that TDR water content measurements are influenced by temperature, residual bitumen, and percent clay in the tailings. A correction of 0.03–0.10/ °C must be applied to the apparent dielectric constant (Ka) to account for the effect of temperature. The Ka-volumetric water content relationships of slurries differ significantly from the commonly used Topp calibration equation. The age of the tailings and the addition of phosphogypsum did not influence TDR water content measurements.

Jan 1, 2013

By E. Adam, B. Milkereit, M. Salisbury, L. E. Reed, G. Perron

Integrating seismic reflection, borehole geophysical, and physical rock property studies is an effective means of mapping lithological contacts and structures in the crystalline crust. At Les Mines Selbaie in the northern volcanic zone of the Late Archean Abitibi Subprovince, a high-frequency seismic reflection profile has provided the first images of deep crustal structures of this important polymetallic mine site. Physical rock property and borehole geophysical studies confirm that prominent seismic reflections can be caused by lithological contacts, faults and sulphide mineralization. At Les Mines Selbaie, the first two of these are shown by this study. Clearly identifiable reflection images from sulphide mineralization have not been demonstrated in analysis of the profile. The seismic images provide useful information about gross structure in the vicinity of Les Mines Selbaie. They can also place important constraints on the sequence of tectonic events and, therefore, can aid future deep exploration programs.

Jan 1, 1997

By Suping Yao, Chuanyu Jiang

In the last decade, the copper industry in China has witnessed a significant change. The capacity and production of refined copper has grown remarkably from 1.5 million tons in 2002 up to 5.88 million tons in 2012. And now, China has become the biggest copper producer in the world, counting about 30% of the global refined copper production. This paper summarized modern copper smelting and converting technologies employed in China copper industry, such as OT flash technology, TSL (ISA/Ausmelt), SKS bottom blowing, Jinfeng side blowing, etc…This paper also presents some key development and improvement of these technologies up to date from their practical application in China, what will contribute as great value to any new / or renovation copper smelting projects down the road. As an engineering company in China, NERIN has been involved in many of these projects in the past decade, played an important role in the engineering works and accumulated intensive experiences. NERIN is one of the best choices for the world clients in the copper industry, providing quick engineering service, delivering cost effective projects.

Jan 1, 2014

By M. Sutherland

"Increased efforts to improve mine safety have led to various successful forms of ground control in Canadian underground mines. At Inca Limited&apos;s T-3 Mine in Thompson, Manitoba, a perimeter blasting method has been implemented in jumbo drilled development headings.The technique utilizes an increased number of perimeter blast holes in the drill pattern while decreasing the linear charge density of explosives in any individual perimeter hole. The decrease in perimeter charge density means less blast damage to the surrounding structure.The benefits realized include increased safety through less loose ground and substantially less scaling time, less overbreak and improved long-term drift stability. This paper highlights the development and implementation of the perimeter blasting program.IntroductionThompson Mine Thompson Mine is a 6000 ton per day underground nickel mine located just outside the city of Thompson, 400 miles north of Winnipeg. The mine is serviced by the T-I shaft and by the T-3 shaft. The shafts are 10 000 ft apart and are connected on several levels with the deepest operating levels at T-1 and T-3 being 4000 ft and 2400 ft respectively.The T-3 Mine presently produces 52% of the total Thompson Mine production and 65070 of the 3000 ft of mine development each month. Current development of the 5 million ton 1, C orebody below 2400 level at T-3 will maintain these production and development ratios.Depending on equipment requirements, development headings at T-3 Mine vary in size. The 1, C ramp, at 17 1/2 ft wide by 10 1/2 ft high, is presently the largest development heading at T-3. Fifty- two per cent of the development footage is done with four Gardner Denver two boom electric /hydraulic jumbos and one Gardner Denver one boom electric /hydraulic jumbo. The remaining 48% is driven with hand-held jack-leg drills."

Jan 1, 1990

By C. C. Li

Traditionally, strong and stiff devices, such as fully encapsulated rebar bolts and concrete lining and arches, are preferred for underground rock support. The attention is paid to the strength of the devices in such support designs. It has been observed in engineering practice that support systems composed of stiff devices are often subjected to premature failure in high stress rock conditions. In the past decade, yield support devices have been employed to improve the performance of rock support systems. A rock support system usually consists of both internal and external devices that are installed within the rock mass and on the free surface of the rock, respectively. Great efforts have been made to make support devices yieldable in the past years, but the efforts are focused on different aspects in the tunneling and mining branches. In the tunneling branch, the focus has been put on the development of external yield devices, such as Lining Stress Controller (LSC), Honeycomb element and compressible concrete, which are embedded in shotcrete liners, while in the mining industry the efforts has been on the development of yield rockbolts, such as the cone bolt and the D-Bolt. The internal and external support devices are not compatible in their deformation capacities in the current rock support systems even though yield devices have been employed. All the devices in a support system should be deformable and compatible in deformation capacity. With such a support system, premature failure of individual support devices could be avoided and the service life of the support system is prolonged. It is a trend at present to take into account the energy absorption capacity, instead of simply the strength, of support devices in rock support design.

Jan 1, 2015

By G. Morin, G. Marin, M. C. Parr, J. Carignan

"Investment casting offers many advantages for the near net shape production of complex geometries, however, molten titanium reacts with most of the refractories used in investment casting shelling systems, which leads to the formation of an oxygen contaminated surface layer. This layer, called alpha case, is 0.1 to 0.6 millimeters in thickness according to the casting section size and must be removed either by mechanical or chemical milling processes. Alpha case removal processes affect casting tolerances and may contaminate the part intended for medical applications (e.g. embedding of abrasive grit media in the alloy). A shelling system based on an yttria prime slurry has been developed and was found to almost suppress the mold metal reaction. Yttria is an expensive refractory, but slurry life was found acceptable for small castings using a closed container and flow coating process instead of conventional pattern dipping. Alpha case depth has been determined for Ti6Al4V by metallographic techniques and microhardness measurements on different step block casting cross sections. Alumina and yttria second prime stuccos were evaluated in this study. The shelling system minimizes finishing operations in the production of casting for medical applications.INTRODUCTIONTitanium investment castings have been in the commercial market since the beginning of the titanium era in the mid 50’s. Investment casting is a cost effective way to produce complex parts for medical, aerospace and chemical processes applications. Investment casting of titanium is difficult due to the high reactivity of titanium with air and refractories used for shell mold building especially for the face coat. Melting is done under vacuum and no shelling system has been proven effective to suppress the mold-metal reaction yet. The main issue with the mold-metal reaction is the formation of an oxygen enriched zone at the surface of the castings named alpha case (Frueh et al., 1997; Kim, 2002; Saha, 1986). The alpha case is brittle, reduce the fatigue life in service of the parts and must be removed by chemical milling.For industrial purposes, calcia partially stabilized zirconia based slurries have become widely used in titanium investment casting for primary coats due to a combination of limited metal shell reaction. Calcia stabilized zirconia slurries have an acceptable shelf life and offer an interesting production window. Our experience shows that a resulting alpha case depth is 280 micrometers for a casting section of 6.35 mm in thickness is typical with such a shelling system (Morin, 2013)."

Jan 1, 2016