Search Documents

By B. F. Osborne

"A new sensor cannot be considered in isolation from the process in which it is utilized. This paper, describing an on-stream particle size analyzer, therefore gives considerable emphasis to the slurry handling techniques employed to ensure that the instrument is presented with a representative sample. A new sampler is described, which continuously abstracts a small, representative sample from a closed pipeline containing a flowing slurry. This sample is then diluted, thoroughly mixed and pumped to a head tank, from where a continuous stream is fed at a constant rate to the size analyzer. Data are presented to show that particle size segregation is minimal throughout this sampling and sample preparation. A continuous particle size analyzer based on a separation principle is described, and the basic parameters of size distributions, and how they relate to this particular instrument, are considered. Typical results are given. An electronic system is presented which accepts the basic sensor outputs, and converts these to a particle size signal suitable for process control. Finally, the use of an inplant computer to process the sensor signals to obtain a particle size signal is briefly considered."

Jan 1, 1972

By A. J. Williams

"IntroductionAN EXCELLENT paper entitled Potash Discoveries in Western Canada (l) was presented to the 1948 Annual Meeting of the C.l.M. by L. Heber Cole, of the Department of Mines and Resources, Ottawa. In the intervening three and a half years, the search for oil and gas in Saskatchewan has added considerably to the information available on the occurrence of potash. It is the purpose of this paper to summarize the additional data. For greater clarity, it may be useful, first, to recapitulate some of the highlights of Mr. Cole's paper.Underlying the western plains of Canada there is a large deposit of sodium chloride, believed to be of early Devonian age. Associated with the sodium chloride are certain potash salts, primarily 'sylvinite,' a mechanical mixture of sodium chloride (halite) and potassium chloride (sylvite) crystals. The potash salts, when present, are usually near the top of the salt formation, though in at least one well they were found near the central part of the deposit. Cole reported on some seven wells in Saskatchewan which had encountered appreciable amounts of potash; these were the Ogema, Radville, Davidson Nos. 1 and 2, Prairie Salt Nos. 1 and 2, and Verbata wells. Depth of potash from surface ranged from 7,653 feet in the Radville well to a minimum of 3,466 feet in the Verbata well. Such depths do not compare favourably with those at which the potash is found in mines in the United States, France, and Germany, where about 1,000 feet is the average. The greatest concentration of sylvite encountered was in the Verbata well, where a bed 11 feet thick carried the equivalent of 21.64 per cent K20."

Jan 1, 1952

By Farnham. G. S.

It is difficult co know how to deal with this subject before a group having such mixed interests. The mining man is not coo concerned with the problems of alloy research. The engineer is more interested in properties of materials than how these properties can be achieved. The business man feels that scientific history and prognostication are not for him, predicting trends or possible developments in the economic field being a more than sufficient occupation. Yet the application of physical metallurgy research to industry is of importance to miner, engineer, and business man, for only through such application can the continuing existence of industries manufacturing or consuming metals be assured. History shows that hard work does not guarantee industrial survival. For instance, the Bessemer method of steel making superseded puddling operations; it, in its turn, has been largely displaced by open-hearth processing; later, steels made in electric-arc furnaces displaced open-hearth products in the quality field; and now, very specialized steels are being made in high-frequency rather than in arc furnaces. It is apparent then, if industry is co remain healthy, complacency must give way co imaginative planning, based on a thorough knowledge of production technique, a knowledge supplied by efficient research.

Jan 1, 1947

By G. H. Charlewood, J. W. McBean

"One hundred years after being developed, the diamond drill is still an essential tool in mineral exploration. The basic principle is unchanged, but the technique has been revolutionized, particularly in the past fifteen years. The cost of core drilling has not kept pace with the rising cost of living. The price of machinery, supplies and labour in drilling has doubled and trebled since 1946. Some of the techniques which have made it possible to hold the price line are described."

Jan 1, 1967

By H. D. B. Wilson

"IntroductionRECENT ADVANCES in geo-chemistry and in •our knowledge •of crystal structure provide a key which enables us to create a systematic picture of the genesis of many ore deposits. This genetic scheme may be used with confidence in assessing certain types of orebodies and may be of some aid in actual exploration, since it affords a rational explanation of the dependence of the composition •of the ore minerals on that of the rock type in which they occur with which they -are •associated. For purposes of the present paper, .the elements chosen are •chromium, vanadium, iron, and titanium. The oxides of all these metals occur in deposits of similar or related type, and it is proposed to show that, for each, the composition of the •ore mineral is related to •the composition of the enclosing :rock, and that one of the principal factors controlling the composition of the ore is the ionic size of its constituent elements.Geochemical PrinciplesThe crystals of the rock-forming silicates and of the magmatic oxide minerals are essentially ionic types. This means that they are composed •of oppositely charged ions such as Mg²+ and 0²-, which are held together by electrostatic attraction. The ions of each element are spherical, with characteristic size known as the ionic radius. Crystals are built up by the packing of these spheres in the most stable arrangement compatible with the size and the size and valence of the ions• involved.Many of the principles governing the formation of ionic crystals are •simple ,and logical."

Jan 1, 1953

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

By V. Schwinn, P. Fluess, N. Cauderlier, J. Bauer

From a strategic and economic point of view, the development of fine grain high strength steels for long distance pipelines is intensified world wide to satisfy the demand for natural gas in the future.The project related property profiles based on strength, toughness, crack arrest and sometimes resistance against HIC at defined design temperatures require an effective structural refinement using advanced steelmaking and processing in the rolling mill. The microstructure of modern line pipe steels ranges from ferritic pearlitic to ferritic-bainitic and structures where bainite is the dominant component, possibly upgraded by secondary phases. This paper illustrates microstructures and properties of recent orders on line pipe steels both for onshore and offshore application using different processing routes in the plate mill. Examples will be given for SAWL 485 offshore grades, X65 HIC and X70 HIC onshore grades, respectively. Finally, production results of a recent X80 order will be presented.

Jan 1, 2005

By D. J. Charlton

"IntroductionMaintenance is a business, which to be successful, requires good management, systems and reporting. The prime objective of the maintenance management group, be they large or small, must be to anticipate and prevent interruptions in operations by keeping equipment in good mechanical condition. This objective should be carried out at minimum cost consistent with maximum productiveness.The objective of this chapter is to give an insight into the various aspects of maintenance management that must be considered to effectively and efficiently operate a mill complex. The degree to which the maintenance sub-systems are developed in an operating mill will be determined by the size of the mill and the needs of the operation.The criterion of the management system used is that the system serve the operation and not vice versa. The systems presented should be considered as tools and, as with all tools, they must be sharpened and replaced as the need arises or as more effective tools become available.To understand what is involved in maintenance management, it is worthwhile to consider a systems approach to analyzing management problems. This approach was developed by J.A.B. Rae while reviewing maintenance management systems for Cominco Ltd.A very simple system involving managing results and objectives is shown diagrammatically in Figure 1.The systems approach to organizational development involves four basic elements: an objective, a result, an activity and feedback. In the analysis, the activity element is broken down into individual actions that people could be held responsible for. If we introduce the action of operating into the diagram of Figure l, we arrive diagrammatically in Figure 2."

Jan 1, 1989

By Georges Houlachi, Akram Alfantazi, Michael Mahon, Maysam Mohammadi

Corrosion resistance of the lead-based anodes directly influences the purity of the final product in the zinc electrowinning process. The anodic MnO2 layer that is electrodeposited on the anodes during this process can protect the anodes against corrosion. Sand-blasted anodes generate a uniform, adherent and shiny MnO2 layer, which gradually blisters and eventually sloughs off after several weeks. In this study, we attempted to develop a new method to stabilize the MnO2 protective layer on the anodes during the electrowinning process by providing suitable nucleation sites for electrodeposition of this layer. MnO2 particles (P80=40µm) were used as seed material for this purpose. Different techniques of galvanostatic and cyclic voltammetry polarizations, scanning electron microscopy (SEM) and atomic absorption spectroscopy (AAS) were employed to investigate the performances of the MnO2-seeded lead anodes. The experimental results showed that growth of the MnO2 layer is influenced by the MnO2 seed particles on the anode surface. The MnO2 layers electrodeposited on the MnO2-seeded lead anodes were uniform and strongly adherent to the substrate. This layer was more stable than those formed on the PbAg anode without MnO2 seeding. This could provide the anode with a higher level of corrosion protection. Moreover, formation of undesirable MnO2 mud in the electrolyte and the rate of manganese consumption were decreased when the MnO2-seeded lead anodes were polarized. These observations could be attributed to the different properties of the electrodeposited MnO2 layer on this anode in comparison with that formed on the PbAg anode.

Jan 1, 2016

By D. L. Cramp

The Direct-Connected Electric Hoist In the latter part of 1931 a new electric hoist was installed at the Lake Shore mine. A number of interesting features were incorporated in this machine, which is the first direct-connected, direct-current-operated hoist to be placed in service in the Kirkland Lake district. Many factors requiring care and study enter into the selection of hoisting-engine drive. In this instance, conditions warranted the selection of the generator voltage control system (Ward-Leonard), utilizing a direct-current driving motor and a separate motor generator unit. It was further deter-mined that additional economies could be secured by the selection of a motor generator unit with a flywheel, and consequently the Ilgner-Ward Leonard flywheel set was adopted. Some of the advantages of this system are: 1) Greater accuracy of control, resulting in increased flexibility in hand-ling with increased precision and safety; especially desirable in large, important installations where the rope-speed is high or where frequent shifting is necessary. (2) Reduced energy consumption. (3) Feasibility of load equalization, without which, in some cases, the power system would be unable to carry the fluctuating load imposed on it by the operation of the hoist. ( 4) Elimination of reduction gearing in the construction of the hoist. The hoist is located on the surface and is used for skip operation at the main shaft, hoisting ore from a present maximum depth of 4,200 feet.

Jan 1, 1933

By B. N. Church, J. J. Barakso, A. F. Bowman

"An evaluation of mineralization in the Goosly- Owen Lake area of central British Columbia is the result of a comprehensive geochemical study of rock samples obtained from a regional geological survey. The dispersion of metals in country rocks about a line of Tertiary intrusions suggests that these igneous bodies may be genetically related to known sulphide replacements, disseminations and vein deposits. The geochemical investigation is based on the determination of 12 elements from samples gathered from more than 800 scattered field stations. To assist processing and interpretation, the data are subjected to a variety of statistical procedures, including correlation of the elements, factor analysis, clustm• analysis and computer contouring of the elements. Some practical applications of rock geochemistry in regional exploration are indicated."

Jan 1, 1976

By Sylvie Lévesque, Frederic Couët, Laura Pérez-Barnuevo, Cory Hennessey

Determining mineralogical characteristics of samples throughout the iron ore concentration process – from drill core samples up to the concentrate – is critical to process improvement and remediation. However, assessment of mineral proportions, liberation, and texture, although essential, can be time-consuming and costly. Thus, a mineralogical study is often not performed or only restricted to a limited number of samples. New iron ore deposits or new ore zones in active mines will bring new challenges as they are known to be problematic due to their lower grades, complex textures and presence of mineral impurities. In those cases, applied process mineralogy will be necessary to understand and to diagnose potential processing issues. To take full advantage of mineralogical information along the iron ore concentration process, new tools are being developed to provide mineralogical data based on texture, composition and liberation. In an early stage at the mine, the automated identification of drill core textures could provide essential information for the prediction of ore concentrability and grindability. In a later stage, the automated modal tool, combining the knowledge of the iron ore mineralogy of a specific deposit and the results of chemical analyses, can quantify the mineral proportions of the ore; results show good agreement between mineral estimation via chemical analysis and modal analysis using a Mineral Liberation Analyser. A bulk mineralogical analyser allowing semi-quantitative evaluation of the liberation of iron oxides is being validated. The results from the bulk mineralogical analyser will eventually be linked with the mineral proportions issued by the automated modal tool to provide complete mineralogical characteristics of iron ore samples. Ultimately, these mineralogical tools could provide valuable and timely insight for predicting concentrators’ performances or troubleshooting gravity separation processes.

Jan 1, 2016

By B. C. Tripathy, S. K. Padhy, R. K. Paramguru, Pinak Patnaik

"Cobalt is regarded as technology enabling metal among the less abundant metals found in the earth crust. Electrodeposition of the metal from aqueous sulphate solutions is the preferred technology for its commercial production. Certain additives are added in the electrolytic bath during electrodeposition for the production of uniform, smooth and bright deposits of cobalt metal with higher current efficiencies and lower energy consumptions. A detailed investigation has been carried out to determine the effect of additive Sodium octyl sulphate (SOS) on the electrodeposition of cobalt. The results indicated that the additive apart from increasing the current efficiency enhanced the quality of cobalt electrodeposits. A maximum current efficiency of 98.4% was achieved at 10 mg/L SOS. The presence of SOS in the electrolytic bath did not result in any noticeable change in the crystal orientation of the cobalt electrodeposits except at higher concentrations (50 g/L) of the additive. Scanning electron micrographs indicate that smooth, compact and uniform deposits of cobalt were obtained at 10 mg/L of the additive beyond which there is detoriation in the quality of deposits. Polarisation of the cathode was seen in the presence of SOS. The effect of SOS on the electro kinetic parameters: Tafel slope (b), transfer coefficient (a) and exchange current density (I0) has also been investigated.INTRODUCTIONCobalt is recognised to be a strategic metal among the various base metals, owing to its numerous applications in various industries. Cobalt as a metal finds its use in the preparation of rechargeable batteries, as an alloying component in the manufacture of space craft and jet engines, as a drying agent for paint varnishes, ground coats for porcelain enamels and in the manufacture of the catalysts for the petroleum and chemical industries (Davis, 2000). Although there is a huge demand of the metal the supply of the metal is limited due to its scarcity in the earth crust. The metal comprises of only 0.02% of the earth’s crust for which the metal is recovered from various ores of nickel and copper as a byproduct (Hawkins, 1998). The present day techniques for cobalt production includes mostly hydrometallurgical methods which are preferred over the earlier used pryometallurgcial methods carried out for the metal production. Almost 70% of the world’s cobalt produced currently is from hydrometallurgical techniques in which electrodeposition of the metal from aqueous solutions is the final step for metal production (Verney, 1988). The most preferred route for electrodeposition of cobalt metal involves a sulphate medium (Das and Subbaiah, 1984; Lenthall and Bryson, 1997; Sharma et al., 2005)."

Jan 1, 2016

By J. Visman

"SummaryThis paper is presented as part of a programme to show the steps taken by industry and others interested in supplying a solid fuel of constant quality to 'satisfy a consuming market. The paper deals with the general principles underlying quality control in coal preparation plants, namely, constant quality and close adherance to acceptance limits. It also describes how control of ash content is ""generally hampered by the problem of coal sampling .and the long duration of the ash analysis and how these difficulties may be overcome.Quality control can be effected in several ways. Thorough blending wll reduce variations appreciably, except those of long trend. The latter can be detected by automatic sampling and quick ash analysis. At present, under favourable conditions, a system of half-hourly ash determinations with an accuracy of 0.5 to 1.0 per cent can be realized, to the effect that trends with a 'wave length' of more than two hours cu be eliminated within the limits of accuracy of the ash figures. The general solution of the problem is a combination of blending, accurate sampling, quick ash determination, and statistical analysis of the pattern of ash distribution.The use of statistical methods of analysis, such as the t test and F test, is •discussed at some length in order to emphasize the importance of the correct evaluation of observational data if there is to be confidence in the validity of test results.General ConsiderationsCOAL, as a fuel, is too cheap for a long haul across the country. The limiting distance depends on the price of the local competitive fuels, and, as the price depends to a great extent on quality, so does quality, to the same extent, command the market."

Jan 1, 1952

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011

By M. B. Kime, E. K. Kanowa

"Heap leaching of low-grade copper-cobalt oxidized ore and solvent extraction of copper, cobalt, manganese, and zinc were investigated. Heap-leaching parameters were optimized using agitated and tray batch leaching tests, capped by tests on a pilot semicontinuous heap-leach plant. The optimum pregnant leach solution yielded 2,350 mg/L Cu, 3,800 mg/L Co, 3,600 mg/L Fe, 130 mg/L Mn, 25 mg/L Zn, and 0.58 g/L solids in suspension, with pH and acidity of 1.27 and 3.66 g/L, respectively. Copper, cobalt, and impurities (Mn and Zn) were extracted using (v/v) 30% CP-150, 20% IONQUEST® 290, and 20% D2EHPA, respectively; overall recoveries of copper, cobalt, and impurities were 98, 99, and 70%, respectively.RÉSUMÉ La lixiviation en tas des minerais oxydés de cuivre et de cobalt et l’extraction par solvant du cuivre, du cobalt, du manganèse et du zinc ont été étudiés. Les paramètres de lixiviation en tas ont été optimisés à l’aide d’essais de lixiviation en discontinu sur un plateau, complétés par des essais relatifs à une usine pilote de lixiviation en tas en semi-continu. La liqueur-mère optimale a produit 2 350 mg/L de Cu, 3 800 mg/L de Co, 3 600 mg/L de Fe, 130 mg/L de Mn, 25 mg/L de Zn et 0,58 g/L de solides en suspension, avec un pH et une acidité respectifs de 1,27 et 3,66 g/L. Le cuivre, le cobalt et les impuretés (Mn et Zn) ont été extraits avec un pourcentage volumique (v/v) de 30 % de CP-150, de 20 % d’IONQUEST ® 290 et de 20 % de D2EHPA, respectivement. Les récupérations totales de cuivre, de cobalt et d’impuretés étaient de 98 %, 99 % et 70 % respectivement.INTRODUCTIONBoss Mining S.P.R.L. is a privately owned hydrometallurgical plant located in southeastern Democratic Republic of Congo. It treats oxidized ores of copper and cobalt that are recovered by sulphuric acid heap leaching (Trujillo, Cisternas, Gálvez, & Mellado, 2014; Kime, Kanowa, Mulaba- Bafubiandi, & Diyambi, 2016) and solvent extraction processes (Crane, Urbani, Dudley, Horner, & Virnig, 2009; Fisher, 2011; Kime et al., 2016). The ore to the plant is primarily sourced from the Luita and Mukondo mines. Geological prospecting work by Gecamines and Boss Mining showed that the Mukondo mine contains a very large cobalt reserve not yet exploited, but with grades as low as 0.2%.Currently, Boss Mining is focusing on the production of copper, but is investigating methods to efficiently produce both copper and cobalt. A challenge in the production of cobalt from this ore is its presence in the third oxidation state. This requires the addition of reducing agents, which increases the overall operating cost (Kime & Makgoale, 2016). Cobalt solvent extraction is also very sensitive to impurities such as nickel, zinc, manganese, and aluminum, which are often co-extracted (Swartz, Donegan, & Amos, 2009). This sensitivity to impurities requires the optimization of operational parameters to lower impurity levels as much as possible in the electrolyte."

Jan 1, 2017

By G. Gabra, M. Nagamori, J. J. Panneton

"RESUMELa calcination contrôlée de 10 serpentine permet de produire de 10 magnésie active. Le degré de I'activation est mesure par 10 solubilité du magnésium dans les acides faibles tel que I'acide acétique, La serpentine contenue dans les résidus d'amiante du Québec peut donc être activée par calcination. Le teneur en magnésie active des rejets d'amiante calcinés est fonction de divers paramètres: température, temps de calcination, granulométrie, etc. Les rejets d'amiante de différentes provenances démontrent des comportements thermochimiques différents qui sont étudiés dans Ie présent travail au moyen d'ATD, de TG, de la diffraction des rayons X et de la lixivation par l'acide acétique. On constate qu'un maximum d'environ 80% de la magnésie totale peut être activé dans certains rejets d'amiante du Québec et Ie degré d'activation dépend de la provenance.vIntroductionOn sait depuis longtemps que la serpentine, Mg3Si2O5(OH)4, un silicate hydroxylé de magnésium, devient amorphe lorsqu'elle perd de I'eau d'hydratation entre 600 et 700 °C. La serpentine ainsi calcinée est alors dissociée en magnésie et en silice. Cette magnésie, dite active, est soluble dans un acide faible ou même dans les solutions de sels d'ammonium.Plusieurs precédés chimiques ont été proposés afin d'extraire sous forme de composés magnésiens la magnésie de la serpentine. La plupart de ces procédés comportent une activation par calcination de la serpentine préalablement à une Iixiviation par un acide ou par une solution d'un sel d'ammonium.Malgré la contamination par Ie fer et par d'autres éléments, les compositions chimiques des rejets de différentes mines d 'amiante du Québec, présentées au tableau 1, sont très proches de la serpentine typique. Puisque Ie degré d'activation de la magnésie varie grandement d'une serpentine à I'autre lors de la calcination, la première étape de la recherche sur la transformation chimique des rejets d'amiante du Québec se résume à une étude de leurs comportements thermochimiques."

Jan 1, 1982

By Paul W. Shelley, Daniel J. Hodges

The mining industry is undergoing a period of rapid transformative change.  This is the result of the social and financial accountabilities that the industry is faced with because of the world’s desire to cap average temperature increase to 1.50C above pre-industrial levels (UNFCC, 2016).  To limit global warming to 1.50C, greenhouse gas emissions must peak before 2025 at the latest and decline 43% by 2030.  In hard rock mining, comminution is identified as the major energy consumer, being responsible for 40-60% of the electricity use.  It follows that comminution is the major greenhouse gas emission process of the mine.  All effort is being made to radically reduce the carbon emissions of comminution. Grinding media plays a large role in the energy consumption and carbon emission story.  In recent years industry practitioners have attempted to quantify the grinding media carbon footprint.  This paper makes a definitive contribution to that discussion.  The grinding media carbon footprint is quantified in Scope 1, 2 and 3 emission terms in the context of a grinding media supplier.  Major emission contributors, steel, natural gas and electricity are discussed in detail.  The steel industry transition is a key factor. The paper will explore the steel industry transition and its effect on grinding media manufacturing.  The carbon footprint of heritage steel process routes are analysed and compared with the process routes of the future.  Emerging steel making technologies are presented and discussed.  The future of the steel manufacturing and procurement route for grinding media is proposed. This narrative allows for a comparison between the heritage carbon footprint and the future carbon footprint of manufactured grinding media.  Of equal importance is the opportunity of reducing the grinding media carbon footprint in the field.  The paper explores possibilities of reducing the grinding media carbon footprint at the customer site.  Media in use options are presented that take account of the mineral characteristics, the mill dynamics, and the product metallurgy to optimise both carbon footprint and media performance. It is intended that this is a landmark paper in the discussion of the carbon footprint of grinding media.

May 4, 2025

By Himanshu Dehra

The pre-fabricated outdoor rooms are often utilised near the mines and construction sites for office purposes. The paper has presented modelling and simulation results of the integration of commercially available glass coated photovoltaic (PV) energy technology and solar ventilation technology into a pre-fabricated outdoor room. The pre-fabricated outdoor room has been setup at Concordia University, Montréal for full scale testing of the glass coated PV modules with solar air ventilation. The computer simulation model has been developed for PV modules installed on a double wall wooden frame in an outdoor room based on its preliminary field testing. The testing apparatus was a wooden frame assembly of double wall with solar air ventilation: two adjacent glass coated PV modules, air column and plywood board filled with polystyrene. The measurement data collected from various sensors were: solar intensity, ambient air temperature, room air temperature, electric power, surface temperatures of PV modules and plywood board, air velocities and air temperatures in the air column. The enhancement in the air velocity of the air column was achieved with an exhaust fan fixed in an outdoor room. The simulation model is used to perform the two dimensional energy analyses with applied one dimensional solution of steady state heat conduction equations. The simulation model is based on conjugate heat exchange paths with network boundary conditions of convection, radiation heat exchange and solar air ventilation heat transport. The model parameters are based on measured values of ambient air temperature, room air temperature, air velocity at outlet of air column in double wall, electric power and available solar intensity. The model has predicted fairly well energy performance of glass coated PV modules with solar air ventilation installed on a wooden frame. The model is also useful for predicting heating, ventilating and air-conditioning (HVAC) requirements for the pre-fabricated outdoor rooms.

May 1, 2007

By W. L. Ennis

Introduction This paper outlines the causes of underground fires at Noranda Mines and the precautionary measures taken to guard against such fi res. Shafts There are six shafts (Figures and lA) on the property, of which N os. 1 and 2 are abandoned. Nos. 3, 4, and 5 are the present working openings from surface and No 6 is an internal shaft. No. 3 is used primarily as a service shaft, while Nos.?1 and 5 are the main hoisting shafts. Orebodies The orebodies are of two distinct types. There are the massive sulphide bodies, and the areas of mineralized rhyolite containing gold values and a silica content high enough for fluxing purposes. The massive sulphide bodies contain chalcopyl'ite, pyrite, pyrrhotite, and minor amounts of sphalerite and magnetite. The concentration of particular sulphides varies even within the same body. It is the areas high in pyrite, and to a lesser degree those, high in pyrrhotite, that are of particular interest.

Jan 1, 1950