Search Documents

"The pressure leaching of alkali-pretreated limonitic laterite ore in nitric acid was studied. The optimal leaching conditions are as follows: leaching temperature of 458 K, initial nitric acid of 2.44 mol/L, leaching time of 60 min, liquid to solid ratio of 2:1 mL/g, agitation speed of 500 RPM. Under the above conditions, the extraction of nickel and cobalt can be achieved as approximate 95% and 80% respectively while that of iron is as lower as 1%. The leaching residue containing 70% of iron in the form of hematite and trace amount of chromium is suitable as the raw material for iron-making. The nitric acid in the leaching solution can be regenerated and further recycled to leach. INTRODUCTIONIt has been estimated that 60%-70% of the world land-based nickel resources presented in nickel laterites containing 130 million tons of nickel although these only accounted for about 42% of the world nickel production (Sudol, 2005; Luo et al., 2010). The nickel resource of laterite has not yet been fully utilized. Due to the increasing global demand of nickel and the declining global reserves of nickel sulphides, there is an increasing focus on the processing of the huge reserves of laterite ores today. Nickel laterite ores can be simply divided into two types, namely, silicate-rich and limonite. The former can be treated effectively by pyrometallurgical process in which the ferronickel product or nickel/iron sulphide matte is produced (Monhemius, 1987). The limonitic laterite is rich in iron in the form of goethite which is the main nickel-bearing mineral and usually contains cobalt associated with a manganese phase (Chang et al., 2010; Georgiou and Papangelakis, 2004). The limonitic laterite is usually processed by hydrometallurgical methods, such as atmosphere acid leaching (AL) (Xu et al., 2005; McDonald and Whittington, 2008), high pressure acid leaching (HPAL) (Chou et al., 1977; Georgiou and Papangelakis, 1998; Rubisov et al., 2000; Whittington and Muir, 2000) and reductive roasting-ammonia leaching (Caron Process) (Whittington and Muir, 2000; Valix and Cheung, 2002). The AL process can proceed at lower temperature, thus the operation costs may be very low. But two biggest problems associate with the AL process, namely, the slow rates of nickel extraction and potentially the significant amount of impurities such as iron and aluminum in the leaching solutions, which hampers the wide application of the AL process. The Caron Process uses the pyrometallurgical and hydrometallurgical methods together to obtain the metallic values, but the overall metal recovery is relatively low, especially for cobalt. In recent years, the environment-friendly process of HPAL has become increasingly important because it is most suitable for low-grade ores and leads to high extraction of the valuables. However, the HPAL process needs a much higher temperature and pressure (503-533 K, 4-5 MPa) to maintain a relatively fast leaching rates, which results in higher operation costs. Moreover, another serious problem of scale formation in autoclaves occurs in the HPAL process, for example, in Moa Bay, up to 20 cm scale may build up resulting in 5 days descale downtime per month. In addition, the iron residues cannot be utilized for ironmaking due to the presence of high content chromium (Ema and Harada, 1987; Owada and Harada, 1987; Takagi and Furui, 1987)."

Jan 1, 2012

By Mike Dry, Mani Manimaran, Mykolas Gladkovas, Mariam Melashvili, Chris Fleming

Development of a new hydrometallurgical flowsheet requires quantitative description and optimisation of all chemical processes in each step in the process, as well as mass and energy balances across a fully integrated circuit incorporating all the unit operations. This paper covers steps leading to early modelling of a gold processing plant based on a bromine/bromide lixiviant. Research conducted at SGS Lakefield in collaboration with Albemarle provided the data that were used in the development of this model. A previous investigation in this series described the leaching behaviour of various mineral types in Stabilized Bromine reagent. This paper is concerned with the gold recovery operations associated with a conceptual bromine leaching process. The recovery of gold by different types of resin and activated carbon was studied, along with various methods of stripping the gold from the extractant. The circuit is closed by electrolysing the spent leach liquor to oxidize some of the contained bromide back to bromine that would allow recycling the regenerated leach solution back to the leach step in the process.

Jan 1, 2015

By H P. Tardif

This paper briefly describes some of the phenomena encountered when materials are submitted to extremely high pressures, such as those produced by the detonation of an explosive charge placed in contact with the material. It was found that extensive changes take place in the? microstructure of iron and steel. Diffusion-controlled processes, such as the transformation of lamellar pearlite, the recrystallization and grain growth of ferrite, and the homogenization of the pearlite-ferrite structure, can take place within micro-or milliseconds. Mechanical twins can propagate without deviation from ferrite to pearlite, thus indicating a proeutectoid ferrite-pearlite-ferrite orientation relationship. The propagation and interaction of intense stress waves in materials was demonstrated with the use of Armco iron. Finally, a comparison is made of the damage produced in metals by the formation of craters made by explosive shock and by hypervelocity impact. D DRING the last few years, exceptional development has taken place in the field of explosive metallurgy, i.e., the

Jan 1, 1964

By W. A. Lang

Introduction In this review, which is the fifth of the series on the Progress in Coal Technology, an attempt has been made to outline some of the more important developments that have taken place in coal carbonization during the last decade. Research into both high-and low-temperature carbonization has been active for three principal reasons: (1) the growing shortages in most countries of high-quality coking coals; (2) the demand for smokeless fuels for domestic purposes; (3) the need for metallurgical coke for the increased output of steel in the post-war years. The growing importance of coal tars as a source of chemicals for the preparation of synthetic products and of coal gases for the recovery of sulphur is evident. Many of the researches initiated because of wartime necessity have been continued .and even expanded in the post-war years. High-temperature carbonization with a suitable coal yields a strong coke which is used primarily for metallurgical purposes, a tar with good marketable value, and a large yield of gas of medium calorific value. Low-temperature carbonization gives a more free-burning solid product suitable for a domestic fuel, a high yield of a tar which is generally regarded as superior to high-temperature tar for chemical purposes, and a smaller yield of a higher-heat-value gas.

Jan 1, 1951

By A. M. Richmond

Introduction The apparent commonplace, and prosaic, nature of building-stones, lime, cement, gypsum, and clay products, and many other miscellaneous non-metallic minerals, such as abrasives, barite, diatomite, magnesite, mica, slate, salts, etc., and their everyday appearance and necessary in our lives, has removed much of the glamour, romance, and speculative attractiveness so frequently associated with our gold, silver, lead, zinc, and copper mining ventures. However, it will be readily appreciated, with but a brief study of the thirty-five or more non-metallic minerals and products which are mined, prepared, or are known to occur, in British Columbia, that the 'industrial minerals' industry in the Province has an abundance of interesting technical problems, is fraught with speculative possibilities, and, as such, fully deserves much more technical attention than it has hitherro received. The brief notes presented in this paper show, in summary form, the magnitude of the British Columbia industrial and non-metallic mineral industry; outline in synoptically form the principal deposits of non-metallic minerals presently known; and indicate in a general way a few of the possibilities which exist in the Province for the expansion of the industry. For convenience in presentation, the assembled material has been divided into four sections: 1.-Sraristical information 2.-Strucrural non-metallic minerals 3.-Miscellaneous non-metallic minerals 4.-Non-Metallic mineral possibilities in British Columbia 1. -Statistical Information The writer does not propose to dwell at length on the statistical comparisons and deductions which may be drawn from the four tables which have been compiled for this section of the paper, nor is it considered essential, as the figures present a most emphatic story in themselves.

Jan 1, 1935

By Jeanne B. Percival, Paul Ramaekers, Charles W. Jefferson, Pat A. Hunt, Eric G. Potter, Katherine E. Venance, William Davis, Sean A. Bosman

"A 10-cm thick clay-rich layer near the top of the Manitou Falls Formation of the Athabasca Group is unusual in its breccia texture, alteration, and detrital mineral composition relative to the adjacent overlying and underlying sedimentary beds. This layer is composed of angular quartz grains set in an illite >> kaolinite + dickite matrix. Deformed clay-rich fragments within the layer have very similar mineral assemblages. The presence of euhedral accessory minerals including Ti-oxides and aluminophosphatesulphate minerals points to a diagenetic/hydrothermal origin. The presence of individual grains of Kfeldspar and amphibole is unusual relative to the typical Athabasca quartz arenite; originally, these minerals were probably included in detrital quartz and subsequently liberated during fracturing. The textures and alteration characteristics suggest that this layer is a hydraulically-fractured unit, which has experienced hydrothermal fluid alteration - a possible pathway distally related to uranium mineralization Une couche argileuse de 10 cm d’epaisseur pres du sommet de la Formation de Manitou Falls du Groupe d'Athabasca est remarquable par sa texture brechique, son alteration et la composition de ses mineraux detritiques qui different de ceux des couches sedimentaires sus- et sous-jacente. Cette couche est composee de grains de quartz angulaires dans une matrice composee d’illite >> kaolinite + dickite. Des fragments deformes riches en argile dans cette couche presentent des assemblages mineraux tres similaires. La presence de mineraux accessoires idiomorphes dont des oxydes de titane et des aluminophosphates-sulphates suggere que ces derniers ont une origine diagenetique / hydrothermale. La presence de grains de feldspath-K et d'amphibole est inhabituelle comparativement aux arenites quartziques typiques de l’Athabasca; initialement, ces mineraux constituaient probablement des inclusions dans le quartz detritique qui ont ete subsequemment liberees pendant la fracturation. Les textures et les caracteristiques de l'alteration suggerent que cette unite a subi une fracturation hydraulique et a ete alteree par un fluide hydrothermal - possiblement en lien avec les effets distaux de mise en place de la mineralisation en l'uranium."

Jan 1, 2013

By T. Crivits

"Freeze lining technologies are used industrially to protect the integrity of furnace walls in pyrometallurgical reactors. This is achieved by solidifying a protective layer of slag on the inner furnace wall. In the current study, laboratory experiments have been undertaken to produce freeze linings in ‘Cu2232 O’-‘FeO’-MgO-SiO slags under controlled conditions using an air-cooled probe technique. Whilst most thermal models of freeze linings have assumed the freeze lining-bath interface to be at the liquidus temperature of the bulk bath and to be planar in geometry, the current research has demonstrated that this is not the case. Experiments undertaken using this high-temperature slag system have shown the interface at steady state conditions to be at subliquidus temperatures. The solid phases present at the interface do not include the primary phase and the interface is non-planar. The study indicates the need for improved understanding of the fundamentals of freeze lining formation, and of the influence of system properties and process parameters"

Jan 1, 2015

By A. Idegami, M. Imamura, S. Heguri, Y. Ozaki

"Nickel powder can be produced by the reduction of a nickel ammine complex solution by hydrogen at high temperature and pressure. To minimize the deposition of fine nickel on the surface of the reactor and other equipment, seed crystals are added to the initial solution to promote nucleation of the nickel powder. Such seed crystals catalyze the precipitation of the nickel particles on the surface of the seed and enhance grain growth. In this study, nickel nuclei were precipitated by the addition of a polymer to the nickel ammine complex solution, resulting in the production of nickel powder. Thus, we herein propose a model that explains the effect of the polymer in the precipitation of nickel nuclei.INTRODUCTIONNickel powder is commonly produced via a hydrometallurgical process from the hydrogen reduction of a solution containing a nickel ammine complex at high temperatures and pressures, and this process was commercialized in the 1950s by Sherritt Gordon (Sherritt International, Canada, Benson & Colvin,1973; The Staff, Research and Development Division, Sherritt Gordon Mines, Ltd., 1958).In the above transformation, upon the injection of hydrogen gas into the solution, nickel is reduced as outlined in Equation(1), ultimately resulting in the production of nickel powder.Ni(NH3)nSO4+ H2?Ni+ (NH4)2SO4+ (n-2)NH3(n:2–6)(1)In this process, seed crystals are added to the reactor to suppress the precipitation of fine nickel (scaling) and to enhance nickel reduction (Benson & Colvin, 1973; Mackiw, Lin & Kunda, 1957). More specifically, iron sulfate and a small amount of dispersant polymer are added, which leads to the formation of nuclei. Upon subsequent hydrogen reduction, the reduced nickel can then be deposited on the nuclei, allowing nickel particle growth to take place. However, this results in iron contamination in the final nickel product, and so the use of pure nickel as a seed crystal is desirable to produce high quality nickel powders."

Jan 1, 2017

By G. F. Liu, S. Owada

Platinum Group Metals (PGMs), Pt, Pd, Rh, have been widely used as a three-way catalyst to clean discharged gas from automobiles and therefore a considerable amount of the spent catalysts is generated annually. This paper proposes a novel concentration technology of PGMs by utilizing the double-deck structure of PGM bearing alumina-ceria and cordierite phases. The applied technologies are a combination of heating-quenching, selective grinding and screening for separating alumina-ceria phase from cordierite. Temperature change as a function of quenching time and the thermal stresses applied to both phases were simulated and calculated by FEM, and it was clarified the mechanism of micro-cracks generation at the phase boundary and micro-cracks in alumina-ceria phase, which indicated that separation of alumina-ceria phase from cordierite and selective breakage of alumina-ceria phase could be achieved in the subsequent selective grinding with an attritor. This process could concentrate 46 wt% of alumina-ceria phase into fine fractions with 86 % recovery efficiency. The remaining alumina-ceria phase can be further recovered by applying flotation and so on.

Jan 1, 2015

By Fathi Habashi

"Hydrochloric acid (HCl), although more expensive than sulfuric, find uses as a leaching agent in reactions involving iron oxide. The reason for this substitution was the discovery that oxyhydrolysis of ferrous chloride by which HCl can be recycled economically. This avoided the pollution of the environment by ferrous sulfate. It was found further that the rate of leaching of sulfides is faster when HCl is used as compared with sulfuric apparently due to the formation of aqueous chlorine. In case of refractory gold ores, HCl leaching under pressure avoids the use of cyanide solution since gold chloride is produced which can be recovered by standard methods. Hydrochloric acid find also uses in the leaching of scheelite and apatite but its use in leaching clay and anorthosite is questionable.INTRODUCTION Sulfuric acid is the cheapest acid and is used as a leaching agent in many hydrometallurgical processes. However, hydrochloric acid (HCl), although more expensive since it is prepared by reaction of sulfuric with sodium chloride, has replaced sulfuric acid in many reactions involving iron oxide. It replaced sulfuric acid for the first time in 1960s in pickling of steel because of pollution problems (Habashi, 2000). Ferrous chloride produced in pickling can be economically decomposed to ferric oxide and HCl according to:2FeCl2 + 2H2O + 1/2O2 ? Fe2O3 + 4HCl (1)which also shows that the acid can be regenerated but ferrous sulfate cannot be economically decomposed to recover sulfuric acid for recycle. Since then, HCl has been used in many leaching processes. Hydrochloric acid is a corrosive acid and is usually handled in rubber-lined equipment. REGENERATION OF HYDROCHLORIC ACID Regeneration of HCl is conducted in fluidized bed or in spray roaster Fluidized bed oxyhydrolysis In a fluidized bed, ferrous chloride solution is introduced onto a bed of hot ferric oxide where heating is provided by the hot fluidizing combustion gases (Figure 1). The solution is fed on top of the bed of oxides. The liquid feed wets the outer layer of the hot oxide particles and is quickly evaporated to form a layer of new solid oxide on top of the existing oxide, thereby producing dense homogeneous particles."

Jan 1, 2017

By L. Tafaghodi, S. Sarbishei

"Following the depletion of nickel sulfide ores, laterites are considered as one of the main sources for producing nickel and cobalt. One of the primary steps in pyrometallurgical extraction of nickel from laterites involves partial reduction of the ore at temperatures below 1000°C. Studying the kinetics of laterite reduction provides valuable information on reducibility of nickel laterites using coal as a reductant. The present study investigates the reduction behavior of a nickel laterite by thermal gravimetric analysis and differential scanning calorimetry. Non-isothermal reduction tests and X-ray diffraction analysis were performed to find the main reactions that occur during the process. The kinetic parameters were calculated by Coats-Redfern method. The general model of simple reaction f(a)=(1-a)n was used for calculating kinetic parameters.INTRODUCTION Nickel (Ni) naturally occurs in the form of sulfide and laterite ores. Laterite ores are mainly available in tropical regions. Weathering phenomena during millions of years has led to the formation of several layers with specific mineralogy (Butt & Cluzel, 2013). The three main layers downward are limonite, smectite, and saprolite (Crundwell et al., 2011). Although laterites are the most available nickel ore resource (70%), their share in the overall Ni production is limited to 40% (Crundwell et al., 2011). The main reasons for not materializing the full potential of laterites are as follows (Ray et al., 1985): •,Laterite ores contain high water content (free and combined) which in turn results in high energy consumption of the extraction process. •,As Ni is present in the form of solid solution in laterites, physical upgrading methods such as flotation are not effective in increasing the Ni content before the extraction process. •,Extracting Ni from sulfide ores involve exothermic reactions which are beneficial due to decreasing the overall energy requirement of the process, however there is not efficient release of energy in the process of extracting Ni from laterite ores."

Jan 1, 2017

By F. Awotwe-Appiah, P. Koshy, J. Dankwah, J. R. Dankwah

This research investigates the generation of an effective carbonaceous material from waste ‘pure water sachets’ and their subsequent utilisation as reductants for the reduction of the Opon Mansi iron ore. Composite pellets of Opon Mansi iron ore and pulverised carbonaceous material generated from waste pure water sachets were heated from room temperature to 1200 °C in a gas fired furnace for seventy minutes. The reduced pellet was analysed chemically for its oxygen and carbon content using a LECO Oxygen/Nitrogen and LECO Carbon/Sulphur analysers, respectively. It was observed that nuggets of metallic iron were readily produced with the carbonaceous materials acting as an effective reductant and source of chemical energy. XRD analysis of waste ‘pure water sachets’ revealed that the polymer was semi-crystalline with peaks that were identical to those of high density polyethylene (HDPE). Gas emission behaviour of the iron ore-PWS pellet was studied in a horizontal tube furnace at 1200 °C using an infrared gas analyser; the results revealed an exhaust gas rich in the reducing gases CO and CH4 along with CO2.

Jan 1, 2015

By J. Armitage, J. Erskine

Feed level and thickness measurements are essential in the optimization of an electric arc furnace. A precise measurement of the feed thickness and level gives operators the ability to increase the smelter efficiency and reduce the maintenance cost. Hatch has developed a radar system which is an affordable, low maintenance, and accurate level measurement system. The radar units can be installed across the furnace to measure the feed level and the feed thickness can be calculated with one slag level sounding. The present paper describes the development of radar systems as a process optimizing tool by furnace controls. The authors will discuss the challenges involved in installing eight radar units on the roof of a six-in-line electric furnace.

Jan 1, 2015

By A. Warczok, T. A. Utigard

"Slags from smelting of copper concentrates contains from 1 to 15% of copper. Copper is present in the form of copper or copper matte inclusions of size from 2 to 1000 micro, and as dissolved cuprous oxide. Removal of the copper requires the slag reduction, primarily reduction of magnetite and co-reduction of cuprous oxide. Thus, the kinetics of the slag reduction play an important role in copper recovery. Instantaneously, at the contact of carbon and a slag the gaseous film is formed. The magnetite and cuprous oxide reduction is going through a gaseous film, separating the slag and carbon of a coke or electrodes. The thickness of a gaseous film grows to a critical value and gas bubbles, containing CO and CO2, are created and rise up in the slag. Results of measurements of kinetic of the slag reduction with graphite showed high value of activation energy, close to the value of activation energy of Boudouard reaction. Strong temperature dependence of the reaction rate points out the thermal instability of the reacting system. It was found that the slowest process in the reduction stages determines the loop of CO and CO2 transfer and magnetite diffusion to the slag/gas film boundary. Strongly endothermic Boudouard reaction seems to cause thermal instability on the reaction surface. So, heat transfer to the reaction surface is very important. Due to low thermal conductivity of a slag the convection dominates in the heat transfer. So, any slag stirring accelerates the rate of reduction and coalescence of metallic copper or copper matte inclusions."

Jan 1, 2015

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

The present work aims at some process modifications in specified metallurgical processes, wherein CO2 can be used successfully as an oxidant for decarburization in steelmaking and applied in some non-ferrous metals production processes. During the decarburization of Cr-containing high alloyed steels, the present researchers investigated the possible use of CO2 instead of Ar-O2 mixture and could successfully decarburize the steel melt without significant loss of alloyed Cr to the slag phase. A mathematical model was developed based on the bubble formation accompanying the chemical reaction: C(molten steel)+ CO2(gas)= 2 CO(gas). The model predictions were tested by laboratory scale (1 kg) experiments carried out in an induction furnace and very good agreement between the model predictions and experimental results were observed. A national project has been sanctioned in China for the implementation of CO2 in decarburization of ferroalloys as well enable the addition of pig iron in the electric arc furnace process when the scrap supply is limited. New processes have been developed for the utilization of CO2 in the case of non-ferrous processes. A novel method of treatment of Al dross by leaching with water and capturing the evolved NH3(formed by the hydrolysis of AlN) has shown very promising results.

Jan 1, 2015

By J. Basi, D. F. Rucker

"A review of historic operating practices of the heap leach pads at the Los Filos Mine, Mexico, revealed periods of restricted cyanide addition, reduced leach time, and insufficient irrigation flow. These issues all led to the buildup of partially leached recoverable gold inventory within the leach pads. Drawing down this inventory represented an opportunity to bring value forward. This paper outlines the strategic initiatives which were implemented as efforts to accelerate the inventory drawdown, including geophysical mapping and pressure injection.INTRODUCTION Los Filos is a heap-leach operation located in the Guerrero gold belt in southern Mexico. Operational and hydraulic challenges at the Los Filos Mine have led to a buildup of gold in inventory within the leach pads. Operationally, periods of restricted reagent addition, reduced leach time, and insufficient irrigation flow have compounded over the last eight years, and resulted in significant inventory growth. Hydraulically, the leach pad has issues with low permeability and solution channeling due to the fines and clay content of the ore. The leach pad is storing high-grade pregnant leach solution (PLS) as perched aquifers above areas that are compacted and difficult to drain. These operational and hydraulic challenges made it particularly difficult to spatially predict the precise locations of the inventory build-up. Fortunately, the challenges at Los Filos are not unique to the mine, and others have taken steps elsewhere to reduce metal inventory through a program that targets areas for inventory drawdown. For example, Ghorbani et al. (2016) noted that a method of injecting barren reagent solutions, applied directly to specific areas of a leach pad to reduce inventory, was presented by Wan and Brierley (1997) and Wan (1997). Seal (2004; 2007), Seal and Jung (2005), and Seal et al. (2012) have put the injection methodology into practice in Nevada and Colorado gold mines with a technology called Hydro-Jex®. The goal of Hydro-Jex has been to supply reagents at a high pressure over a short duration, followed by periodical low pressure rinse periods to remove leached metal and resupply fresh reagent to the ore."

Jan 1, 2017

By C. Riveros, H. Henein

Bulk Metallic Glasses have a high potential as advanced engineering materials due to their various properties including strength and corrosion resistance, to name a few. This paper investigates amorphous phase formation and rapid solidification characteristics of impulse atomized Co-based alloys in order to understand and control the application properties of the final products. Amorphous fraction and kinetic crystallization properties of the atomized Co-based alloy powders were quantified by means of Differential Scanning Calorimetry. In addition, different but complementary characterization tools were used to analyze microstructures of the powders. These include optical microscopy, X-ray diffraction and micro-hardness tests. While the amorphous fraction within the powders is promoted by high cooling rate and smaller powder size as expected, hardness is found to decrease with the fraction of amorphous phase.

Jan 1, 2015

By Bruce Macdonald

Operational reservoir management activities such as cyclical steam, water or CO2 injections frequently cause surface micro-deformation. InSAR monitoring from space based sensors of this surface deformation has become a valuable approach to confirm and monitor extraction and injection activities. Sequestration of CO2 into deep saline aquifers is discussed as an important long term solution to slow future climate change. This method requires reliable continuous monitoring to assure that captured CO2 is sequestered in the substrate for ?all time? (typical minimum requirement by law is 20-30 years). We have shown that combining flow and deformation modeling with spaceborne synthetic aperture RADAR interferometry (InSAR) measurement of ground uplift caused by the underground release and spreading of the CO2 can be forged into a powerful tool to monitor sequestration. We used a novel InSAR approach to resolve the surface motion over the In Salah, Algeria CO2 sequestration site. Our approach exploits all information contained in an interferometric stack by exploiting both persistent distributed as well as persistent point scatterers. Displacement time series are obtained with a network inversion approach applied after topographic error and preliminary atmospheric correction of the network (dual-scale technique). After inverting the original network data to common master we then use an advanced spatio-temporal filtering scheme to remove the remaining atmospheric phase components down to scales of 1 km or less. By comparing final displacement series from multiple interleaving InSAR stacks we show that the accuracy of our refined solution to detect uplift outside of significant temporal data gaps in the InSAR stack is significantly better than 1 mm per year. We further show that accuracy and robustness to data gaps are both significantly improved by co-inverting multiple datasets with the same and different sensors. This co-inversion method also allows the seamless continuation of the monitoring from one sensor to another.

Jun 1, 2012

By A. Takala, H. Cline, D. Girard

"This article describes the project development and successful implementation of a particle sorter at the Kensington mine. The Kensington underground gold mine and associated milling facilities are located within the Berners Bay Mining District on the east side of Lynn Canal about 45 miles north-northwest of Juneau, Alaska. The paper describes the project from concept, through the development phase, including test work confirming feasibility, to a discussion of operational data and includes shared experiences from operation and maintenance. The project has proven successful in recovering gold that was previously lost to the waste dump and has already resulted in a positive return on investment. The payback was achieved in less than one year.INTRODUCTION The first paragraphs of this paper describe Coeur Mining and the Kensington Mine, its history, geology, mining operation and mill. The second part of this paper gives a quick introduction to sensor-based sorting in general and X-ray transmission sorting (XRT) in particular. This article does not cover costs or economic impacts apart from the pay-back period for the investment at Kensington. Interested readers find more in information on this in the literature (Kleine & Wotruba, 2010; Robben, 2013). Since the publication about XRT sorting at TGME in Pilgrim’s Rest (Kleine, Riedel, Ketelhodt, & Murray, 2010), this is the first time that a comprehensive data set on gold ore sorting using XRT is published. Following chapters highlight the aim of the project for Coeur Kensington, project development through testing and operation before concluding. ABOUT COEUR MINING’S KENSINGTON OPERATION Coeur Mining is the largest U.S.-based silver producer and a significant gold producer with five precious metals mines in the Americas employing approximately 2,100 people. Coeur produces from its wholly owned operations: the Palmarejo silver-gold mine in Mexico, the San Bartolomé silver mine in Bolivia, the Rochester silver-gold mine in Nevada, the Kensington gold mine in Alaska, and the Wharf gold mine in South Dakota. The Company also has a non-operating interest in the Endeavor mine in Australia in addition to royalties on the Cerro Bayo mine in Chile, the El Gallo complex in Mexico, the Zaruma mine in Ecuador, and the Correnso mine in New Zealand. In addition, the Company has two silver-gold feasibility stage projects—the La Preciosa project in Mexico and the Joaquin project in Argentina. The Company also conducts ongoing exploration activities in Alaska, Argentina, Bolivia, Mexico, and Nevada. The Company owns strategic investment positions in several silver and gold development companies with projects in North and South America."

Jan 1, 2017

By Tanai Marin

Modelling of pyrometallurgical processes can become extremely challenging when the process involves complex chemical reactions, phase change, multiphase flows, heat and mass transfer and fluid flow. Traditionally modelling involving complex thermodynamic equilibrium and thermochemistry are treated separately from problems in which transport phenomena are dominant, such as CFD and heat transfer studies. The separation is also necessary due to the lack of modelling tools that can effectively couple both solution thermodynamic and transport phenomena or even multiphysics problems. However, there are, quite often, problems in high temperature process metallurgy in which it is not possible to simplify this two modelling approaches. Typical cases of this are for example, the modelling of slag freezing on furnace walls (electric or flash furnaces) to create a protective layer in front of the refractories hot wall, the formation of build up from the matte or metal phases at the hearth of the furnace, calcine smelting from charging piles into slag phase, etc. The problem is even more challenging in nonferrous pyrometallurgy as most, if not all, of the condense phases are highly non ideal solutions involving several components and exhibiting complex crystallization paths and miscibility gaps, such as the Fe-Ni-Cu-S matte, FeO-Fe2O3-SiO2, FeO-MgO-SiO2 slags, etc. In this paper, an approach to model coupled problems involving multiphysics and solution thermodynamic is presented. The approach consists in developing in-house a library containing the Gibbs energy minimization routines and using the local equilibrium concept for process modelling from a multiphysics commercial software (COMSOL). Simple test cases, such as building a non-ideal binary phase diagram on a CFD package is presented, the limitations and of other classic approaches such as equilibrium or Scheil cooling are discussed and compared to this model.

Jan 1, 2015