Search Documents

By K Myers

Since the mid-1990s, the Chino Mine Facility (Chino) located near Silver City, New Mexico has been developing a closure plan with financial assurance to protect water quality, as required by State regulations. In February 2002, Chino and the New Mexico Environment Department (NMED) reached agreement on a closure plan; a closure cost amount of approximately $US 394 million ($A 591 million) was finalised in April 2003. Both the New Mexico Water Quality Act Regulations (1977) and the New Mexico Mining Act Regulations (1993) guided development of the closure plan and financial assurance amount. The process incorporated many years of correspondence, studies, negotiations and administrative hearings. The major technical issues focused on regrading slopes of the leach ore stockpiles and waste rock piles; cover systems; water treatment systems; and abatement of ground water contamination. The proposed financial assurance amount covers all closure costs and provides for perpetual water treatment.

Jan 1, 2003

By Jardine G, Woodall C

The Henty Gold Mine, located in Western lasiuania use, uuiusatise solutions to effectively manage a mining operation in an environmentally sensitive setting and has been presented with several environmental awards. Fill is required as part of the mining method to provide passive ground support, minimise rock exposure and ensure maximum recovery of the small but high-grade orebody. The use of the whole portion of leach residue in the backfill reduces the surface tailing disposal requirements. Therefore, High Density Paste Fill (HDPF) has been selected as the most appropriate fill method to meet these objectives. Additional benefits include the minimisation of excess water from fill and the subsequent need for the collection and treatment of water and slimes. There are minimal equipment requirements during placement, thereby optimising mine resources for production. The initial paste fill design was based on the Bad Grund and Ranunelsberg Mines paste fill systems of Preussag in Germany and comprised pumping filtered tailings paste some 1.2 kin uphill from the mill to the mine portal, where cement was to be added before being distributed underground. The system was designed following initial testwork that was undertaken on a bulk sample of ore mined from the scar surface Sill Zone. Subsequently, during the mining of the Zone 96 orehody, it was found that there were significant mineralogical variations in the composition of the ore mined. Following processing, the resultant Icach residue caused significant changes in the paste rheology and therefore the pump and flow characteristics. An alternative solution was implemented that involved the use of agitator trucks to transport the cemented paste to the portal. This required modifications to the fill preparation system and also the underground distribution system. Laboratory strength tests of the HDPF using actual gold plant leach residue showed low early strengths were attained with HDPF containing only filtered leach residue. Therefore, high binder addition rates or an increase in the fill cycle time would be required to allow the fill to gain sufficient strength. A considerable amount of potentially acid generating waste rock also requires underground disposal. By blending the waste rock with the HDPF, the strengths were improved and the required cement addition rate reduced by about one-half. The potentially acid funning waste rock is encapsulated in the highly alkaline cemented paste, minimising the potential for acid generation.

Jan 1, 1998

By M Mohammad Khani

An economic block cave is dependent to the characteristics of the rock mass at stages of caving. These are cave initiation, propagation and ore flow. In this research, the rock engineering system (RES), first established by Hudson (1992) to solve complex rock engineering problems, is introduced and verified against the well-established caving parameters established by Laubscher. There are two types of factors influencing caving and these are natural (cannot be controlled) and induced (operator controlled). A RES based interaction matrix is developed by determining the rating parameters required to reproduce the caving database using Laubscher’s caving parameters. This provides the relative importance of the parameters in the interaction matrix. After discussing the rock mass caving process and identifying all the effective parameters, an interaction matrix is introduced to study the cave initiation of rock masses. The expert-semi-quantitative (ESQ) coding method is utilised to assign the numerical value to each parameter’s interaction. Thereafter, the interaction intensity and dominance of each factor in the system is determined to classify these factors. Finally, all the parameters affecting caving operation and their weights on the RES system are identified. This new application of RES in block caving is very efficient and useful for any stage of caving studies and helps experts to make decisions more accurately.CITATION:Mohammad Khani, M, 2016. The application of rock engineering systems to block caving to identify the effective parameters, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 853–860 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By L W. Palmer

"Evaluating the geological risk associated with ore deposits is becoming common practice in the mining industry. While geostatistical simulation is a useful tool for evaluating this risk, the effect of applying different types of simulation is less understood. For simulation of categorical variables like rock types, available methods perform simulation in fundamentally different ways. In this study, the geological risk relevant for informed mine planning is studied with two categorical simulation methods, PluriGaussian Simulation (PGS) and Sequential Indicator Simulation (SIS). Risk is expressed as a probability of repeated occurrence of lithological units in the same location across simulations. Significant differences are observed between the methods in terms of spatial distribution of risk. To identify the most plausible risk model, the input parameters at every step of both techniques are scrutinised. PGS and SIS inputs are classified as four parameters that are: fundamental to implementation of the methodfixed to enable comparison of PGS and SISdetermined by user interpretation, hence variablenormally optimised during application of PGS and SIS. The effect of parameter selection from categories 1 and 4 on the risk model is investigated using drill core data from a leucogranite deposit. A corresponding block model is created for assigning outputs from PGS and SIS. Risk models produced by either method are illustrated in a cut-out from the block model to enable bench-by-bench comparison. For PGS, risk associated with relatively rare lithologies is relatively sensitive to variation of parameters. Independent of the abundance of lithology, a location-dependent effect of variogram and vertical proportion curve parameter selection is observed, with risk increasing towards the deposit edge. Although SIS requires fewer inputs, single lithologies must be modelled in turn. Using small numbers of samples in the search neighbourhood, all risk models differ substantially. For larger numbers of samples, the risk models are similar. Overall it appears that the risk model produced using SIS is less sensitive to changes than PGS but further work is required to confirm this.CITATION:Palmer, L W and Glass, H J, 2014. Risk associated with rock type prediction using simulation techniques, in Proceedings Ninth International Mining Geology Conference 2014 , pp 217–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By J S. J van Deventer, D C. Shallcross

New developments are taking place in the recovery of gold from leached pulps that are based upon the adsorption of the metal cyanide species onto ion exchange resins. Despite the success of several resin-in-pulp pilot plant operations in the Western World and large-scale plants in the former Soviet Union, the process is yet to gain recognition as a viable alternative to the carbon-in-pulp process. An experimental research program has investigated the use of a variety of different types of resins for the recovery of gold, but to-date no resin studied has the desired properties of high selective loading capacity for gold cyanide and a simple inexpensive elution procedure. In addition very little is known concerning the physical strength of resins and their ability to resist shattering due to osmotic shock during cycles of adsorption and elution. The ability of ion exchange resins to enhance the leaching of refractory and re-adsorbing ores has not been investigated. This paper highlights the necessary factors that need to be addressed before commercialisation of ion exchange technology for gold extraction is feasible.

Jan 1, 1998

By V Gupta, Z Huang, S K. Biswal

G-Cell is a new design modification of the Imhoflot pneumatic flotation technology, which utilises a self-inducing aerator inside a downcomer, where bubble-particle attachment takes place. The present study has investigated the suitability of the G-Cell technology for cleaning fine coal using a 0.8 m diameter prototype unit at a coal preparation plant operating in the Midwestern United States. A slip-stream obtained from the overflow of raw coal cyclones operating in the plant, containing nominally minus 150 micron size particles and having ash content in the range of 40 per cent to 50 per cent and sulfur content in the range of 1.30 per cent to 1.50 per cent, has been used as the feed for the G-Cell. The performance data produced from the G-Cell tests are found to be very close to the ideal performance curves produced from release analysis. A statistically designed experimental program has been conducted to investigate the parametric effects on various key process responses, such as combustible recovery, product ash and sulfur rejection. The empirical models developed in this study have been utilised to identify a suitable experimental region for achieving a desired combination of response targets.

Jan 1, 2005

By R W. Henley, L Knuefing, M Turner, Y Zhang, M Saadatfar, A Limaye, R Cruikshank, M A. Knackstedt, A Kingston, L Beeching, N Francois

A better understanding of ore fragmentation and the textural features of ore is a key to the energy efficient extraction of targeted minerals from low-grade ore deposits. In this study, X-ray microcomputed tomography (micro-CT) is employed to study mineral liberation during the tensile failure and onset of fragmentation of a copper ore. Our results show that X-ray micro-CT could inform new studies of ore micromechanics and fragmentation at the laboratory scale and may offer new avenues to address current challenges in the design of efficient comminution processes. We present the results of experiments based on a high-pressure apparatus enabling micromechanical studies to be carried out in situ (inside a micro-CT scanner). This platform produces high-quality 3D images of the evolution of a sample of porphyry copper ore during an in situ fragmentation test. A sequence of tomographic images enables mapping in 3D of both the deformation of mineral phases and the fragmentation process. The fragmentation occurs quasistatically through multiple stages starting with an initial tensile fracture splitting the ore diametrically, followed by tensile-activated nucleation and growth of multiple fractures producing a complex fracture network. Coupling breakage with microstructural information enables quantitative determination of the impact of ore texture heterogeneity on fracture patterns and mineral liberation. This microstructural information can be compared to key measurements of the ore mechanical behaviour such as the global deformation energy, strain deformation field and the stress relaxation response. The latter allows one to identify interesting precursor signals of the tensile failure. The copper liberation, fragment size distribution and breakage patterns are statistically characterised and related to comminution mechanisms which are clearly identified in the sequence of tomographic images. The two dominant mechanisms are rock-rock friction/compression induced by fracture closing and compression-driven fragmentation at rock-crusher contact points.

Aug 24, 2022

By C Samuelsson, Q Shu, A Lennartsson, F Gyakwaa, A Andersson, J Isaksson

The physico-chemical property, viscosity, is essential for pyrometallurgical processes and influences the settling rate of valuable metal droplets in slag, affecting the metal recovery. The copper slag from smelting furnaces typically contains between 1 and 2 wt per cent Cu, which equals to or is higher than in most sulfidic copper ores mined today, meaning the slag is a valuable resource for copper extraction. A low viscosity is desirable for slag-cleaning through a settling furnace where entrained droplets settle under gravity. One approach to control the viscosity is through the slag composition. The literature has limited data on the correlation between viscosity, slag structure, and optical basicity of iron silicate slag with FeO/SiO2, CaO, and Al2O3 as factors. Therefore, the present study evaluated the influence of these factors on viscosity and correlations with slag structure and optical basicity. The FeO/SiO2 ratio (at%/at%) and the CaO and Al2O3 content were altered in two levels, resulting in a two-level full factorial design with three factors. The study was done by synthesising FeO–SiO2–Al2O3–CaO–MgO–Cr2O3 melts, followed by water granulation. The melt structure of the samples was analysed with the help of Raman Spectroscopy. The viscosity was then estimated with a high-temperature rheometer using a Mo spindle and crucible. The results showed a correlation between the optical basicity, FeO/SiO2 ratio, and viscosity, where a high optical basicity and FeO/SiO2 ratio were beneficial for achieving a low melt viscosity.

Jun 19, 2024

By J Cortinez, P Vallejos, J Yianatos, M Rodriguez

Nowadays, one of the main problems in current flotation plants and new projects is the significant decrease in feed grades and changes in the mineral composition, which has an important effect on the mineral liberation and associations. Additionally, flotation plants usually operate with feed throughput higher than the original design, which has a significant impact on the feed particle size. All these conditions affect metallurgical performance, and must be evaluated and addressed, by improving control strategies for banks optimisation. For this purpose, the flotation of valuable minerals along the circuits requires better understanding, considering the compromise between performance and selectivity in flotation circuits. This paper presents a characterisation of the different minerals recovered along industrial flotation circuits. Plant sampling campaigns, performed in a copper industrial concentrator in Chile, provided the data for the study. Two rougher flotation banks consisting of cells of 130 m3 and 300 m3 were analysed. All the samples from the industrial surveys were analysed by screening and mineralogy, and the mineral recovery along the circuits was evaluated per particle size class, liberation class, type of associations, and others. Additionally, operating data on froth depth profiles complemented the evaluation of the mineral composition of concentrate streams, along the circuit. The results allowed for identifying and quantifying the main factors that affect the copper recovery and concentrate grade along the flotation banks. It was found that minerals with liberation lower than 50 per cent have a significant impact on the recovery. On the other hand, the decrease in the Cu grade in concentrates along the flotation circuits is mainly due to the relative increase of middling minerals (less liberated), non-valuable floatable minerals, such as free pyrite, and gangue entrainment. The characterisation of the gangue entrainment flow rate along the flotation banks showed a strong relationship with froth depth, which becomes more critical towards the last cells of the banks.

Aug 24, 2022

Responsibility for the administration of mineral resources is divided between federal and provincial governments. The paper traces the evolution of mineral policies at both levels of government, from the end of World War II to the present. In the immediate post-World War II years, the emphasis was on supplying the raw material needs of a rapidly growing world economy. Policies favouring growth and development of the Canadian mining industry were instituted during this period. Two decades of uninterrupted expansion (the 1950s and 1960s) ensued. The decade of the 1970s was a turbulent one for Canadian mineral producers. Governments intervened more substantially than ever before. Moreover, the industry suffered from an intense period of competition for resource revenues by the two levels of government. At the same time, far reaching changes were taking place in the structure of world mineral markets. To date in the 1980s, the mineral industry has, perforce, adapted to existing mineral market structures. Mineral policies, too, have shown signs of adapting to the needs of the mineral industry. Whether the resulting mix of policies will permit the revitalization of the Canadian mining sector remains to be seen.

Jan 1, 1986

By D J Williams

Coal washery wastes comprise tailings, finer than 0.5 to 0.1 inn depending on the sophistication of the washery, and coarse reject, typically finer than 50 mm. Subaerial disposal of coal tailings slurry at about 30 per cent solids by mass results in the formation of a delta with an average slope of about 1 in 100, representing one extreme. The ravelling of coarse reject on loose-dumping, results in an angle of repose slope with an angle of about 37" (1 in 1.3), representing the other extreme. The pumped co-disposal of coal tailings and coarse reject results in the formation of an upper delta with an average slope of about to one in ten, between the two extremes. The depositional behaviour of these three waste streams is discussed and compared in this paper. The important depositional and material parameters, and a theoretical description of the processes involved, are also presented. Comparisons are made between the depositional behaviour of the various coal washery waste streams, and natural depositional systems, such as rivers, alluvial fans, and scree slopes.

Jan 1, 1998

The region we call the West Coast is acknowledged as one of the richest and most diverse mineral provinces in the world. It's the most rugged part of Tasmania and our island is one of the most rugged parts of Australia, so that speaks for itself. A hostile land of razorback mountains, deep ravines, dangerous rivers, almost impenetrable rainforests and a climate that can change from mild to freezing in a matter of hours.

Jan 1, 1993

By C J. Moran

All mines face water management challenges. Adopting leading practice water management strategies can help reduce both operational and strategic risks. While many of the water issues faced by underground mines are the same as other operations, underground mining presents some unique water management challenges. In this paper we review trends in underground mining, water use and associated water issues. We then compile a structured set of strategic and operational risks that are pertinent to underground operations. The causes, threats, opportunities and measures for controlling or mitigating the risks are summarised. The risk compilation could provide an addendum for underground operations to the Australian governments leading practice water management handbook.

Mar 21, 2011

By A G McLean

This paper will first discuss the fundamental requirements for reliable discharge of backfill by gravity alone at high per cent solids. This discussion will include brief mention of the underlying principles of saturated solids flow contrasted to that of stirred tank or dilute discharge systems. Here the need to possess full knowledge of the flow properties of the stored material will be highlighted. In regard to attainment of reliable discharge it will he revealed flow from a backfill silo will only occur provided: ò the flowing material in the converging channel is yielding throughout; ò slip is occurring along the walls; ò an arched stress field is present in the vicinity of the outlet; ò the flowing backfill must be dilating to flow in response to the dilating stress field; ò sufficient dilation water is injected, in the hopper, to eliminate the formation of adverse interstitial pressure gradients; ò sufficient dilution water is injected, downstream from the hopper outlet, to generate a pumpable slurry of maximum per cent solids; ò the silo level must be sufficient to prevent the pump suction forming a rathole; ò the system must be configured and operated to generate stable discharge density; and ò the system must be configured and operated to minimise damage to the pump liners. In addition proper account must be made of the silo overflow weir and settling capacity to match plant throughput. Here opportunity will be taken to highlight the complexity of this multi-phase flow situation as well as the general yet paramount requirements for reliable solids flow. It will be shown that by proper attention to the multi-phase considerations gravity discharge of slurries as a consolidated bed with minimal water content is possible. Such high solids discharge results in greatly reduced demand for process water. In addition pumping costs are reduced as is the delay time associated with the mine drainage operation. Confirmation of successful applications will be highlighted by reference to several recent case studies. In the concluding phase mention will be made of the key yet very simple and effective operation techniques which enhance reliable Discharge.

Jan 1, 1998

By Grady B. V, Ault A. R, Newman O. M G, Fraser R. J, Malcolm J. McPhersqn

In all electrolytic zinc plants cadmium is removed as an impurity prior to the zinc electrowinning stage of the process. Cadmium metal is the favoured form of this by-product and most plants use an electrolytic route for its production. The formation of dendrites in cadmium electrowinning processes is the major limitation to deposition rates. There is an economic incentive, therefore, to better understand the factors affecting their growth. A technique that has been used by others to examine fundamental aspects of dendrite growth has been applied to industrial strength electrolytes. It involves potentiostatic deposition in a cell containing the electrolyte of interest. The variation in the current with time at a given overpotential allows the determination of the dendritic growth induction time. A method was developed (the Locus method) from the investigation of a set of such potentiostatic curves, obtained over a range of applied overpotentials, that appears to give a measure of electrolyte quality with respect to dendritic growth in galvanostatic deposition. The Locus technique predicts that zinc at industrial concentrations in cadmium electrolytes should have a significant effect on morphology and that deterioration of morphology will occur as the zinc concentration in the electrolyte is increased. This effect is consistent with literature prediction and was shown to relate to a reduction of the diffusion limiting current density. Magnafloc R333 is used as an additive at Pasminco Metals-EZ to control the morphology of cadmium deposits and the Locus method was successful in predicting its dendrite inhibiting properties. A possible mechanism is discussed. This work has opened avenues for future research with respect to a technique that may have an industrial application in electrolyte characterisation and has pointed to a direction in which better understanding of galvanostatic dendritic growth may be found.

Jan 1, 1993

By Holmes RJ, Sowerby BD, Watt JS

Major improvements have taken place in mineral and coal processing in the last decade. The development of nuclear on-line sensors that continuously analyse the material being processed has led to better control of metalliferous mineral processing and increased recovery of valuable minerals. The recent development of on-line techniques for analysis of coal is expected to be of similar Importance. Australian developments in on-line nuclear gauges are reviewed. These include systems for in-stream analysis of mineral slurries with comments on plant operating experience; on-line determination of ash in coal using low energy Y-ray transmission and pair production techniques; in-stream determination of solids weight fraction and ash content of coal in slurries with variable voidage; and on-line determination of moisture in coal, iron in high grade iron ores and sulphur in lead sinter.

Jan 1, 1986

By P A. Grossman, J H. Rubinstein, M Brazil, K G. Sirinanda

To date, the scheduling and access design of an underground mine have only been considered as two separate optimisation problems. First, access to the mine is designed and then the scheduling is completed. One drawback of this approach is that the costs of access construction fail to be reflected in the net present value (NPV) calculation. In this paper, designing the access and scheduling its construction are formulated as a single optimisation problem.The underground mine access construction process can be classified according to the number of faces being developed concurrently. An underground mine with a single decline branching at a junction point into two declines is considered. After construction reaches the junction, the two faces of the decline can be constructed sequentially or concurrently.This paper proposes an efficient algorithm for optimally locating a junction point to maximise the NPV where two faces are being developed concurrently. The NPV is defined by taking the locations of orebodies and their values, decline construction costs, decline development rate and discount rate into account. The variation of the NPV and the optimal locations of the junction point for one and two concurrent development faces for a range of discount rates are discussed and compared. The proposed algorithm is applied in a simulated case study based on hypothetical values for an underground mine.CITATION:Sirinanda, K G, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2014. Strategic underground mine access design to maximise the net present value, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By A Melkumyan, K Silversides

The banded iron formation-hosted iron ore deposits located in the Hamersley Ranges of Western Australia contain marker shales that are used to distinguish lithology for geological and orebody mapping. These marker shales produce distinctive signatures in the natural gamma downhole logs, which are conventionally manually interpreted. This paper proposes an alternative method of automatically identifying these shales using dynamic time warping (DTW). A Gaussian processes (GPs)-based method for automatic identification is also considered. Both methods are tested on a deposit that contains the Marra Mamba sequence of the Hamersley Province.Both methods were trained to predict the location of the desired shales, and the resulting outputs were compared with a manual interpretation of the results to determine the accuracy. The GP method can identify signatures with an accuracy between 87.0 per cent and 92.0 per cent, which increases to 92.9 per cent and 95.7 per cent where the GP is certain. The DTW method has an accuracy between 90.0 per cent and 91.6 per cent, which increases to 94.0 per cent and 95.4 per cent where the DTW is certain.The GP method has several advantages, including a more automated library building process, a probabilistic output and a shorter run time. However, the DTW method was capable of accepting more distortion in the signature and therefore identified more signatures. This is important in a deposit where the signals are frequently distorted by events such as hydration and folding. Both methods provide a viable alternative to the current manual detection, but their differences make them applicable to different cases.CITATION:Silversides, K and Melkumyan, A, 2014. Comparison between Gaussian processes and dynamic time warping for classification of marker shales in iron ore deposits, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 177–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

Cretaceous volcanic activity (Hauterivian Albian) in the Peruvian Andes can be found along the coast of Peru and the western edge of the Andes mountains between 15o30'S and 5o30'S, extending discontinuously in south to Chile and north to Ecuador and Colombia. This volcanic activity formed in three aborted marginal basins; the NNW-trending volcanic Ca±ete and Huarmey, and NNE-trending Lancones basins. These volcanic rocks are predominantly andesitic and basaltic in composition, of calc-alkaline and tholeiite affinity with subordinate dacitic and rhyolitic rocks. One notable feature is the appearance of æocoitasÆ from Ica (14oS) south to Santiago de Chile. These rocks have a calc-alkaline to alkaline affinity. From south to north, the continental crust gradually becomes thinner, allowing mantle material to rise towards the surface. Ophiolitic sequences of this type form a marginal basin in Colombia. Very low-grade regional metamorphism which affects the volcanic rocks also varies gradually from south to north. Between Santiago de Chile and Ica this takes the form of burial metamorphism, with moderate geothermal gradients (20o-30oC/km). Metamorphism in the Huarmey basin is transitional between burial and ocean-floor metamorphism, with very high geothermal gradients (>3000C/km). High geothermal gradients are also apparent in metamorphism of the Lancones basin, though less than the other basins. Ocean-floor metamorphism is present in the ophiolitic sequence in Colombia. Associated mineral deposits in the Huarmey and Lancones basins, and in the north, are of the volcanic massive sulphide-type (VMS). The principal deposits in Peru are Leonila Graciela (20 Mt Zn and Pb) and Tambogrande (40 Mt Cu and Zn). There are also smaller mines and prospects. To the south of Lima, manto-type Cu deposits (CuMT) are found with a mineralogy of chalcopyrites, pyrites, magnetite, actinolite and apatite. The main example is Raul Condestable (10 Mt Cu). Other prospects are present to the south and Chile has some very large mines of this type (El Soldado, Lo Aguirre). The notable differences between the CuMT and the VSM deposits are thought to be the result of the prevailing conditions in the earthÆs crust during the Hauterivian Albian. To the south, calc-alkaline and alkaline volcanic activity in aborted marginal basins, with thicker crust, was thick, produced moderate geothermal gradients associated with burial-type regional metamorphism and deposits of CuMT. In the north aborted marginal basins associated with calc-alkaline to tholeiitic volcanic activity and a gradually thinning crust, produced transitional regional metamorphism between burial-type and ocean-floor type, associated with high to very high geothermal gradients and VMS deposits. In Colombia these conditions led to ophiolite extrusive rocks, ocean-floor metamorphism and also VMS deposits.

Jan 1, 1999

By P Breuer, D J. Robinson, A McFarlane, L L. Kuhar

Increasing global demand for commodity metals and capital and the greater operating costs of mining and metal production present significant challenges for the metals mining industry. Current conventional technologies may not be feasible for processing deposits of declining grade, challenging mineralogy or those that occur at increasingly greater depths. To overcome these issues, the development of a step-change technology such as in situ recovery (ISR), which reduces mining and avoids milling costs, may be vital in ensuring future economic metal production. ISR has been used extensively to treat porous soft rock deposits such as the water-soluble salts, sylvite and halite. Although ISR has typically been used for mining conventionally uneconomic uranium ores, it has also been used less frequently for the treatment of other restricted permeability hard rock deposits, such as those containing copper and gold. The reason for the limited uptake of the technology for hard rock mineralisations is primarily due to low natural rock porosity and permeability and hence poor response to available lixiviant. However, additional challenges include solution containment, management of groundwater and regulatory, ecological and societal requirements and expectations. CSIRO has focused on understanding the challenges of hard rock ISR and identifying global capabilities that can contribute to developing the essential enabling technical areas required to realise ISR. Specific focus areas include geochemistry and advanced resource characterisation; drilling and controlled rock-breaking technologies; solution chemistry and environmentally benign lixiviant systems; lixiviant delivery systems and ‘subsurface mixing’; subsurface hydrology and reactive transport mechanisms and models; downstream processing options; legal, social and environmental aspects; and techno-economic modelling. This paper will discuss ISR challenges including industry feedback focused on addressing this issue, gaps preventing ISR from being applied in practice, capabilities to overcome these gaps and the development of a collaborative approach to making hard rock ISR a reality.CITATION:Kuhar, L L, Breuer, P, Robinson, D J and McFarlane, A, 2015. Making hard rock in situ recovery a reality, in Proceedings Third International Future Mining Conference, pp 189–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015