Search Documents

By A Batnasan, K Haga, A Shibayama, K Higuchi, H Takeuchi

High silica (SiO2), alumina (Al2O3), and phosphorus (P) contents in iron ore adversely affect the quality of iron products. The removal of those impurities from iron ore is an essential point in further iron ore processing. In this paper, the removal of P, SiO2 and Al2O3 impurities from iron ore by alkaline drying followed by reverse cationic flotation is discussed. The reverse cationic flotation experiments are performed using the iron ore samples without and with alkaline drying pretreatment. All other flotation conditions except pulp pH (4–12) and particle size distributions (-45 to -250 μm) are held constant. A typical collector and frother, such as dodecylamine acetate (DAA) and methylisobutylcarbinol (MIBC), are used in the flotation experiments. Alkaline treatment is conducted before flotation using sodium hydroxide at fixed conditions. The impact of alkaline drying on the performance of iron ore flotation is evaluated based on the removal rates of P and SiO2 + Al2O3, iron grade, and iron recovery compared with the iron ore flotation without alkaline drying (direct flotation). X-ray diffraction (XRD) analysis indicates hematite and goethite are the main minerals in the iron ore, which assays 62.8 mass per cent Fe, 0.232 mass per cent P, 7.1 mass per cent SiO2 + Al2O3 (total) determined by X-ray fluorescence analysis (XRF). Results indicate that a combined approach is more effective for removing P and SiO2 + Al2O3 impurities from iron ore than the direct processing technique because the maximum removal rates of P and SiO2 + Al2O3 are 48.2 per cent and 66.5 per cent from the alkaline dried iron ore when 8.4 per cent and 13.1 per cent from the non-alkaline dried iron ore.

Sep 18, 2023

By Y Li, D J. Williams, E Topal

A mine waste rock dump does not have any intrinsic value, yet is an inevitable structure in surface mining operations. Since the purpose of mining is to maximise profit, possible expenditure reduction in hauling waste rock to the dump, which can represent up to 50 per cent of the total operating cost, is highly desirable. Apart from cost, potential acid mine drainage (AMD), due to seepage from surface waste rock dumps containing reactive waste rock, could threaten the ecological balance, drinking water supplies and irrigation systems downstream from a mine site. In order to minimise these potential risks, selective placement of benign and reactive waste rock, and the encapsulation of reactive waste rock by benign waste rock, need to be carried out during the construction of the rock dump.In this paper, a new methodology, based on mixed integer programming (MIP) is developed to manage waste rock dumping. The model aims to minimise waste rock haulage costs by locating the optimum destination(s) for each waste rock block, while at the same time controlling the placement of reactive waste rock to minimise the potential for AMD. Tests on small-scale virtual data demonstrated that the model is capable of dealing with selective placement of different waste rock types, encapsulating reactive, potentially acid forming (PAF) waste rock, and stockpiling benign waste rock for encapsulation and rehabilitation purposes. The solution time for the MIP model is far less than the traditional manual approach, and the resulting schedule is up to 46 per cent more cost effective.CITATION:Li, Y, Topal, E and Williams, D J, 2012. Mathematical approach for better mine waste rock dumping management, in Proceedings Life-of-Mine 2012 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By J J. Grobler

The George Fisher Underground Mine at Mount Isa applies the long hole open stoping methodology. During the reconciliation process of transverse stopes in the George Fisher North mine it was identified that excessive underbreak was regularly experienced, with the major contribution coming from the toe area inside the stope.While over break and the resultant dilution was well investigated and well understood, limited work was done on underbreak improvement. It was decided that a re-engineering process would be followed in an attempt to improve results. The prevailing stoping practices were scrutinised and the possible causes were listed.Some of the identified causes were design, drilling accuracy, equipment condition, mucking practices and direction of firing. It was identified that in most instances the underbreak was initiated in the slot area of the stope during the first firings. Once this happened, it was impossible to get good recoveries on the rest of the stope. The slot area was carefully scrutinised and the blasting practices were changed individually.During the following two years several different strategies were trialled to increase the toe recoveries. The results indicated an overall improvement of six per cent reduction in underbreak on average, by ensuring drilling accuracy and changing the direction of firing. The economic significance of these results outweighed the time and additional work load expended to establish the cause of the problem. This paper outlines the continuous improvement process undertaken to identify and rectify the major contributing factors to the problem. It also presents a set of recommendations to be followed in order to achieve positive results.

Mar 21, 2011

By H Benzer

Grinding clinker to finished cement consumes more energy than any other comminution process. World production of cement in 2009 was 2840 million tonnes and the energy required for comminution was 40-60 kWh/tonne depending on the clinker characteristics and the fineness of the finished cement. Machines used include single and multi compartment ball mills, HPGRs, vertical roller mills, centrifugal air separators, V separators, screens and crushers. The circuit most commonly used consists of a closed circuit HPGR followed by a single compartment ball mill and an air separator, and in operation the variables are adjusted to obtain maximum throughput with no loss of quality of the separator fines.A common objective in cement plants is to reduce energy consumption without affecting the particle size in the finished cement and simulation is used as one procedure to achieve this. Models are now available for all the machines commonly used in clinker circuits and circuit optimisation studies using simulation have been carried out in many plants leading to decrease in energy consumption per tonne of cement. In this paper the models used will be discussed briefly and several case studies will be reviewed which will highlight the effect of change in ball size in a two compartment mill, the role of the HPGR in an HPGR – ball mill – air separator circuit, and the use of a high intensity vibrating mill for producing finished cement with high additive ratio.

Aug 8, 2011

By P Moser, R Ivanova, F Ouchterlony

This paper describes model-scale bench blasts on mortar blocks with distorted drill hole patterns, done in 2013–2014 at the Montanuniversitaet Leoben. The main aim of the project is to see if the fragmentation from and the crack development behind blasts with and without drill hole deviations differ significantly.The dimensions of the test blocks were 660 × 280 × 210 mm (L × W × H). They were mounted inside a yoke that allows the blast waves to escape (see Figure 1). Three rows in each block were shot row by row with a nominal pattern of B × S = 70 × 95 mm. The same nominal delay 73 µs (ie 1 ms per m burden) between holes was used throughout. Blocks with holes of stochastic collar position errors (variations in burden or in burden and spacing but constant row volume) and systematically shifted collar positions (blasts with staggered pattern) were shot. The results were compared to reference blocks without collar deviations.Apart from the sieving analysis, the remaining bench faces were measured with a stereo-photogrammetric method and horizontal roughness profiles for each row were constructed. Sawing slabs from block remains after the third row and use of dye penetrant allowed the study of internal blast damage.The analysis showed that none of the changes in borehole collaring had a significant effect on the sieving curve (median). The sieving results confirm earlier findings though that the fragmentation gets finer with the number of rows shot, implying that blast damage from earlier rows has an influence on the blasting results. The tests demonstrated that the nequiv (equivalent n-value) has increased ten per cent by shooting staggered pattern and decreased by seven per cent by pattern with burden and spacing errors. For the rest of the patterns, the nequiv was roughly the same.The surface roughness investigation showed that a smooth surface was achieved by the staggered pattern. The other deviations patterns did not show a clear trend.The internal blast damage, which was measured in the remaining part of blocks, showed that out of eleven, four crack families seemed to be most affected by blasting. The comparison of the reference and distorted patterns showed that less cracks were apparent for the staggered pattern, ie less damage was introduced.CITATION:Ivanova, R, Ouchterlony, F and Moser, P, 2015. Influence of distorted blasthole patterns on fragmentation as well as roughness of, and blast damage behind, remaining bench face in model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 693–706 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Wolff

One critical factor in open pit mining projects is the estimation of the recoverable reserves. The reason for this is that at the valuation stage there is a lack of information about future metal prices and production costs. Consequently, the estimation of the recoverable reserves needs to be done based on a fixed break-even cut-off grade (BECG), in which fixed expected metal prices and production costs are assumed throughout the operating life of the mine (OLM). In this paper, an alternative technique for estimating the recoverable reserves of an open pit mining project is presented and explained in detail. The main characteristic of this technique is that it estimates the recoverable reserves of the project using mining costs as reference: this is done due to the fact that mining costs are easier to model than metal prices. Another important characteristic of this technique is that it uses the uncertainty of the geology of the orebody, given by simulations of the deposit, to make final strategic decisions, such as the selection of the operating life of the mine and the optimal production rate, which minimise the risk of not achieving future production targets while maximising the upside potential of future rewards. As it will be shown, the final outcome of the proposed technique is the generation of a robust open pit design, that include cutbacks and ultimate pit limits, called the marginal open pit mine design (MOPMD). One characteristic of the MOPMD is that, at each production period, it will be characterised by their respective geological uncertainty, given as probability distributions of ore, waste and metal quantities, and by marginal economical project indicators, such as cut-off grades and metal prices, among others. The details follow in the paper.

Jan 1, 2006

Research cruises dedicated to seafloor hydrothermal activity along the Kermadec arc first began with the Sonne-135 expedition in 1998. This was followed by the worldÆs first systematic survey for venting along an arc during the 1999 NZAPLUME I expedition. Since then, cruises dedicated to mapping plumes along the Kermadec arc include NZAPLUME II (2002), NZAPLUME III (2004) and ROVARK (2007). In addition, the manned submersible cruises SWEEP Vents (2004) and NZASRoF (2005) utilised the Shinaki 6500 and Pisces V, respectively, to sample in detail select hydrothermalsystems for mineralised samples, rocks and vent fluids. The ROVARK (2007) cruise was the first to deploy an autonomous underwater vehicle (ABE) along the arc which surveyed Brothers volcano at a far greater resolution than had been done previously by ships on the sea surface. While these expeditions have largely been led by GNS Science, together with its collaborators from National Oceanic and Atmospheric Administration, Pacific Marine Environmental Laboratory (NOAA/PMEL), significant contributions have been made by other groups from various nations, exemplifying the global interest in seafloor hydrothermal activity associated with intraoceanic arcs. This is an ASTRACT only. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By J Vann

Mineral Resource and Ore Reserve estimation is a challenging and demanding field, requiring application of professional knowledge, skill and experience of the highest order. If the many potential pitfalls are to be avoided, however, there are two other requirements which are of equal, if not greater, importance:good communication, and common sense. Estimation of Mineral Resources and particularly of Ore Reserves is almost always a team effort, involving a number of disciplines. Good teamwork requires good communication, both between team members and between the team and other parties having an interest in the process. Breakdown in these lines of communication can have far reaching effects on the project under consideration. The need to use common sense during a Resource or Reserve estimation exercise would seem to be self-evident. It is surprising, however, how often rigid adherence to procedures and methods prevails at the expense of clear thinking, usually with adverse and sometimes fatal effects on the project under consideration. This has become increasingly true as computerised methods have assumed a central role in Resource/Reserve estimation. The critical question that estimators should ask themselves at all stages of the process is: æIs what is being done sensible given the data available, what is known of this deposit and the purpose of the exercise?Æ

Jan 1, 1999

This paper presents a review of computer techniques for the automatic contouring of geological and geophysical data with output as interactive display on graph plotters or graphics terminals and passive display on automatic drafting tables. The advantages of the method of fitting a triangulated surface to randomly distributed data using an advancing front algorithm are described, as well as the technique for determining interpolated values for the production of contour line segments and a contour smoothing algorithm. This contouring method is employed by the Geological Survey of Queensland and is implemented as an interactive system. An alternative method ideally suited to randomly distributed data involves the use of piecewise parametric cubic splines. This method which is ideal for sharp variations in magnitude and areal extent typical of geophysical anomalies is discussed. The mathematics of surface interpolation using non-parametric splines and an explicit piecewise surface fitting technique are discussed. Curve tracing techniques which are suitable for automatic contouring are also presented and the inherent advantages of interactive contouring using on-line plotters and graphics terminals for previewing of displays are described.

Jan 1, 1977

By T Baumgartl, B Richards

The association of specific plants and plant communities with soils developed over underlying superficial orebodies and mineralisation has been long recognised. It has given rise to the use of plant indicators for geobotanical exploration as a regular component of primary minerals reconnaissance where there is an undisturbed vegetation cover. That the chemical composition of indicator plants is a measure of their soil environment has further led to biogeochemical prospecting methods for minerals and its use in the mapping of underlying ore deposits. Where there is a strong surface expression of metal and metalloid anomalies, concentrations of potentially phytotoxic elements may reach a level at which they have strong selective impacts on plant populations. In such circumstances, natural selection has operated in the development of a unique flora composed of plant species and individuals with genetically-based tolerances to the stressed environment in which they continue to survive. These plants are called metallophytes. Metallophytes occur globally on all metalliferous sites, both in pristine undisturbed environments and in areas of mineral workings, ancient and modern. However, the best-developed primary metallophyte vegetation is found in the most ancient areas where there has been a long-term evolutionary impact of the underlying geology through ore weathering and dispersion of metals into the rhizosphere zone. Natural selection of metal-tolerant races of plants in these largely undisturbed areas can eventually lead to speciation and the development of an endemic regional metallophyte flora (Baker et al , 2010). Mineral wastes resulting from mining activities also allow colonisation by metal-tolerant individuals leading to the establishment of metallophyte communities. The distribution and extent of such communities is determined by regional and local factors relating to climate and substrate conditions and the availability of suitable plant resources on which natural selection can operate (Baker, 2009).The ability of metallophytes to tolerate extreme metal concentrations commends them as the optimal choice for ecological restoration of mineral wastes and metal-contaminated sites. Metallophytes have recently also spawned several novel phytotechnologies, including phytoremediation and phytomining (Chaney et al, 2000, 2005; Baker and Whiting, 2008). Action towards conserving the global metallophyte resource base is imperative because many species are under threat of extinction from new and extensive mining activities (Whiting et al, 2004). This has been identified as a priority in the Mining, Minerals and Sustainable Development (MMSD) Project of the Global Mining Initiative in 2002 but positive responses from the minerals industry have been slow. The last decade has, however, seen an ever-increasing interest in metal-tolerant and metal-accumulating plants, both from an academic standpoint and their use in revegetation and phytostabilisation (Tordoff et al, 2000; Baker and Whiting, 2008; Baker, 2009). Few studies have highlighted the need to conserve and develop these unique plants (Whiting et al , 2004). This presentation identifies future research needs for the conservation and exploitation of the global metallophyte biodiversity and its potential in sustainable mine closure. CITATION:Baumgartl, T and Richards, B, 2012. Evaporation and salt transport under variable climatic conditions, in Proceedings Life-of-Mine 2012 , pp 179-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By M J. Dunn

The geotechnical model is the cornerstone of any mining geotechnical design and as such the confidence level and reliability of the geotechnical model is paramount. The geotechnical model confidence level needs to be commensurate with the level of design that is being applied or study that is being undertaken. The geotechnical model is made up of several components and the reliability of the data underlying these components ultimately determines the reliability of the geotechnical model.Data reliability is linked to the quantity of data collected, the spatial distribution of the data collected, quality of the data collection and the interpretation of the data. In a typical project, there is an opportunity to improve data reliability through the scoping, prefeasibility, feasibility and final design and implementation stages.Currently, very little quantitative guidance exists in the literature on assessing the confidence level of geotechnical studies, although there have been attempts by various authors (Haile, 2004; Haines, Swart and Kruger, 2006; Read and Stacey, 2009; Dunn, Basson and Parrott, 2011) to qualitatively describe what level of geotechnical data is required. Recently a number of authors (Read, 2013; Fillion and Hadjigeorgiou, 2013; Thomas, 2013) have outlined methods that could be applied to assess the reliability of some types of geotechnical data that are used in the development of geotechnical models.This paper briefly discusses some of the factors influencing data reliability and the geotechnical model confidence and some of the tools available.CITATION:Dunn, M J, 2014. Geotechnical models and data confidence in mining geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By L Tatnell, R Mackay, A Tolooiyan

The multi-reversal direct shear test (MRDS) method is commonly used to measure the residual shear strength of soils. However, when the standard direct shear (DS) apparatus is used, the MRDS method is prone to two major sources of error: load cap tilting and specimen loss. These two sources of error can cause erratic behaviour in the residual shear strength curve, making it difficult or even impossible to determine the correct residual shear strength value of the specimen being tested. This paper presents the results of new modifications to the standard DS apparatus that prevent load cap tilting and specimen loss. Consolidated drained testing was performed on highly-over consolidated cohesive soil samples from a Latrobe Valley open pit mine, with results obtained from the modified DS apparatus showing a great improvement in the residual shear strength profile compared to those obtained using the standard apparatus. Large numbers of reversals (up to 14) conducted on a single specimen in the modified DS apparatus showed no notable load cap tilting and no specimen loss occurred. The modifications are easily applied to the standard DS apparatus, and analysis and correction of the data are simple.CITATION:Tatnell, L, Tolooiyan, A and Mackay, R, 2014. Measurement of residual shear strength using a modified direct shear apparatus, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 425–434 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By O Bøckman, E Thisted, K H. Esbensen, U Thisted

Process industry measurement systems, once installed, are often interpreted as static black boxes delivering correct values as long as not proven otherwise. After first implementation and set-up with a distinct sampling frequency, they often run ‘forever’ without checking if this frequency is still appropriate with respect to changed raw materials characteristics, different process conditions or changed customer specifications. Failure detection is based on operator experience and skills (often close to an art form) and/or from control measurements of reference samples. This may well be too late for many industrial process contexts. An appropriate sampling frequency is a critical success factor for valid monitoring and control.Based on the methodology of variographic analysis we here illustrate how to design/re-design/optimise an industrial measurement system in terms of sampling frequency, discretisation and accuracy based on customer specifications. We also show how variographics can be used to monitor for deviations. We use experience from process industry to show how these methods can be used not only for product characterisation, but also for monitoring input factors, process indicators and measurement of these. The information hidden in the vast amounts of data that is continuously created in modern process industries can be utilised to cut costs in the measurement activities and at the same time contribute to early error detection. We illustrate by case examples from production processes at a nickel refinery, supporting the Lean and Six Sigma methodology. This will provide a standard operating procedure for monitoring the stability of measurement systems, and provide a basis with which to discuss how a variographic approach can be integrated with the Lean and Six Sigma approach as an online tool to map, characterise and validate measurement systems and thus avoid more cumbersome measurement system analysis in full detail.CITATION:Thisted, E, Thisted, U, Bøckman, O and Esbensen, K H, 2017. Variographic case study for designing, monitoring and optimising industrial measurement systems – the missing link in Lean and Six Sigma, in Proceedings Eighth World Conference on Sampling and Blending , pp 359–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The Gold Ridge Mine is an open-cut gold mine in the Solomon Islands. The mine is owned and operated by Gold Ridge Mining Limited, a wholly owned subsidiary of Ross Mining NL. At the invitation of the Solomon Island Government, project construction commenced in July 1997 and gold production commenced in August 1998. The mine is the countryÆs first, and represents a major milestone in the development of the Solomon Islands. At the time of project approval and construction, there was a growing awareness in the country of the potential impacts of mining in the tropics, partly due to unfavourable publicity surrounding a number of other mining operations in the Pacific region. The management of environmental impacts was therefore an important consideration in the approval of the project, and continues to receive a high level of attention from the Government and community. Ross Mining did not commit to the Gold Ridge Project until it had satisfied itself that all waste rock and tailings could be safely contained on-site, and that the standards normally expected of a mine in Australia could be met. Ross Mining approached the approval, construction, and operation of the Gold Ridge Mine with a set of operating principles that met Government and community concerns. These were:best practice environmental management; operation of the mine in accordance with standards expected of mining operations in Australia; independent peer review of key technical aspects; on-going consultation with Government and community; and equitable transfer of wealth to landowners and the local community. As a consequence, the Gold Ridge Mine has developed into a successful mining operation with a high level of support from local landowners, the general community and the Central and Provincial Governments of the Solomon Islands.

Jan 1, 1999

By B Green

With a focus on safe productive tonnes, there has been an ongoing drive to increase the productivity of the mining fleet across BHP Billiton. In response, a team from the Iron Ore business was formed to review all aspects of the end-to-end drill and blast process and to challenge conventional practices that limit production efficiency. As a result of the outcomes of this work, a number of initiatives were identified to improve operational practices that have also delivered significant cost savings.One such initiative was to increase pattern size to a minimum of 1 Mt where practicable, thereby creating ‘megablast’ as a new standard across all mines. To achieve blasts of this size, the team had to overcome the complex problem of integrating wall control into the megablasts.With traditional blasting techniques, the key strategy, which is also historically inefficient but was thought to be integral to having stable, safe walls, was to utilise the trim blasting/modified production blasts technique (ie narrow blasts along the pit wall designed to ‘peel off’ the material while minimising the effects of vibration and charge confinement on wall integrity).Small traditional trim patterns comprise three to four rows of production holes and one or two rows of batter/buffer holes of reduced diameter that require the firing face to be completely exposed before blasting. This is an extremely slow process that requires a lot of resources for very little tonnage while adding additional expense to the final cost per tonne.This paper will show how the megablast approach was developed to control damaging vibration and confinement effects, flyrock and fragmentation while having the largest possible blast that includes wall control. The new practice is based on a theory that involves the initiation point and control row being the second row of holes from the pit wall itself. Adjusted charges in vented batter and buffer holes help to achieve an optimal toe design, and at the same time create a zone of broken ground that absorbs damaging vibrations formed by the attached production blast of any size, whether it is a straight wall or a multi-angled complex pit shell design.Using the new style of blasting has allowed an increase in the size of the patterns from an average of 300 kt to over 1 Mt whilst maintaining pit wall integrity. Case studies will be presented showing drill, charge and tie-in designs with the presentation having additional blast videos, including overall shots of blasts and in-close footage of what happens behind the blast at the crest of the planned catchment berm.The paper will also demonstrate the flow-on effect of using this style of blasting to reduce operational costs associated with other downstream processes, such as the reduced requirements for pattern preparation, an increase in productive digging, reduced maintenance costs and a decrease in fuel burn for equipment.CITATION:Green, B, 2015. Megablasts – enabling technologies in BHP Billiton Iron Ore, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 599–606 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Sishen uses a state-of-the-art tracking system to track material from its position in blast blocks through various stockpiles and crushers. Qualities are blended directly to the crusher as opposed to blending from stockpiles. This poses an interesting challenge to the planning department to simulate these conditions. The software used in these simulations are Whittle 4X and Maximiser for long-term planning, Xpac for medium-term planning and Mine Works Planner for short-term planning. Geological models and mine design layouts utilise Surpac. Sishen introduced Xpac a number of years ago; the system has developed and changed over the years. With the Sishen Expansion Project (SEP), which aims to utilise low-grade material, major changes to the planning process have to occur. SEP requires that the mine have two different plants, which utilise two different ROM feeds and have different beneficiation curves. Xpac is used to produce a rolling 18-month plan, which is as close to actual operations as possible. In order to do this, the simulations have to take into account the plants beneficiation curves, stockpile movements, hauling distance and equipment needs. On top of this, the schedule has to continually consider specifications for Fe and the contaminants. Plant yields also have to be kept within a certain bandwidth. Xpac is used to simulate the above parameters, as well as generate the raw data required to produce a mine budget. The paper will also show how the 18-month planning process and subsequent planning processes are measured and aligned. Xpac has proved to be an excellent tool to achieve these goals.

Jan 1, 2005

By J-P Franzidis, M Esvelt, E V. Manla

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant that is able to treat up to 2 tph solids. It consists of a bank of six 130 L WEMCO« SmartCells« and a bank of six 50 L WEMCO« SmartCells«. It was developed as part of the AMIRA P9 Project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. However, it may also be used to carry out pilot-scale flotation test work. This paper briefly describes the circuit modelling, simulation and scale-up test work performed using the FCTR and the use of the FCTR in pilot-plant test work performed by the metallurgical staff at WMCÆs Kambalda Nickel Operations and Mount Keith Nickel Operation. At both Kambalda and Mount Keith the FCTR was found to be very flexible and straightforward to run, with an easily changeable circuit configuration and stable operation. Testwork was facilitated through having full stream sampling on all streams, and a high degree of instrumentation providing accurate measurement of process variables. The results obtained from the FCTR testwork were highly repeatable. As a consequence of using the FCTR, WMCÆs Kambalda Operation and Mt Keith Operation were able to complete a rigorous programme of pilot plant testwork more quickly than in the past, and with a high degree of confidence in the results.

Jan 1, 2003

By J E. Everett, F Grobler

This study considers realistic data for a planned open pit iron ore mine, but is applicable to any open pit situation. By interpolating drill hole data, grades are generated for a rectangular block model. Each blockÆs grade designation vector has components for each analyte (chemical element or compound) influencing ore value. Interpolation by means of geostatistical kriging leads to each block being assigned its expected value, and thus underestimates the overall grade variability. Alternatively, interpolation by means of conditional simulation is a method that implements random sampling from an infinite population of solutions. Each conditional simulation has appropriate overall grade variability, but estimating any blockÆs mean and variance requires sampling from multiple conditional simulations. For a block model, an ore/waste selection criterion maximises the expected tonnage at a target grade. This criterion is a linear composite of the grade components, with positive coefficients for the beneficial analyte (iron) and negative coefficients for the deleterious analytes (such as silica, alumina and phosphorus).Although conditional simulation gives the same expected grade as kriging for each block, the expected maximum tonnage of ore selectable at a target grade may differ from that obtainable from the kriged solution. We apply the linear composite selection criterion to each of 25 conditional simulations, as well as to the kriged block model. The resulting distribution of product tonnage is confirmed to have an expected tonnage that is over 20 per cent greater than that of the kriged model. The method also enables a selection probability to be computed for each block, and thus a probabilistic pit boundary distribution to be identified and used in mine planning. Proposed extensions will consider risk-based scheduling of the multiple selection solutions through minimisation of a derived æstress factorÆ and treating the mining process as an iterative system with actual or artificial ædepletionsÆ modelled in line with the mine plan, using the updated state (with new information) to re-evaluate the mine plan for subsequent periods.CITATION:Everett, J E and Grobler, F, 2013. Risk-based ore selection from conditionally simulated block models, in Proceedings Iron Ore 2013 , pp 149-156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The Pilbara region, located in the north-west of Western Australia, is significant as the second-largest source of iron ore on the planet. Iron ore mines owned and operated by Pilbara Iron are located within the Hamersley Basin. This paper refers to the Greater Paraburdoo mines, the 4WEST and 4EAST pits, located on the southern margin of the Hamersley Basin. The groundwater model refers to ephemeral watercourses: Seven Mile and Pirraburdoo creeks, which are adjacent to the two pits, and Ratty Springs, located upstream from 4WEST and within Pirraburdoo creek. The spring and creeks hold cultural heritage significance for local Aboriginal communities. Two of these, the Gobawarrah Minduarra Yinhawanga (GMY) and Innawonga native title claim groups, initiated hydrological work on the two creeks and Ratty Springs, with the aim of determining the affects of dewatering on the natural water flows of these systems. The numerical model used to simulate drawdown in the Pirraburdoo and Seven Mile Creeks was derived from PMWIN Pro software and covered an area of 77 km2. The modelling period was from January 1998 to December 2004, and the prediction period was from January 2005 to December 2015. The model has four layers and incorporated effects caused by mining voids, 4WEST and 4EAST pits, creek bed material, weathered bedrock below creeks and surrounding banded iron formations (BIF). The model has been calibrated using the trial-and-error method set down by Middelmis et al (2001). The current dewatering schedule (12 ML/day) in the 4WEST and 4EAST mining areas does not affect the water table levels in the adjacent creeks significantly or for any considerable periods of time. However, changes to mine plans may occur, for example, in response to changed commodity price and may lead to significant increase in rates of vertical advancement. This, in turn, affects dewatering schedules, as greater vertical advancement requires increased dewatering effort. When an accelerated mine plan is applied to the model and dewatering rates increased to 18 ML/day, drawdowns in the creeks are more noticeable. The model has therefore helped to indicate the extent to which increased dewatering rates may be acceptable, especially in terms of immediate and longer-term damage to riparian species, ie Melaleuca and Eucalypt. Predictions from the model may also allow mine planners to schedule decreased rates of vertical advancement, where these are required to meet environmental constraints.

Jan 1, 2006

By X Hill

Throughout the 2016/2017 financial year, the NSW Resources Regulator conducted an assessment of each underground metalliferous operation across the state to assess how each operation managed the principal mining hazard of ground and strata control. The assessment considered all aspects of the mining process, including all aspects of managing geotechnical risk within drawpoints. This assessment is ongoing and, therefore, this paper is limited to the first six mines assessed in the program.In 2015 there were three fatalities in and around underground drawpoints in Australian metalliferous mines. Whilst many of the systems of work around underground development are consistent across the industry, there are large discrepancies around how each underground mining operation manage the risks associated with drawpoints.For drawpoints to be effectively managed, their management needs to be considered at the earliest stages of the mine planning process. By using downholes and adopting remote systems of work – systems that are continuing to improve with technology – the risks drawpoints posed can be greatly reduced.The assessment by the NSW Resources Regulator revealed a number of common failings across the state in the management of the risks that drawpoints pose. The assessment also observed a number of innovative practices that particular operations have adopted in the wake of serious incidents occurring within drawpoints at their operation; however, these practices have not been communicated to other operations.It is hoped the learnings from the assessment can be considered by industry and reduce the risks drawpoints pose in underground metalliferous mines.CITATION:Hill, X, 2017. Learnings from review of drawpoint management across New South Wales mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 143–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017