Search Documents

By O Dominguez

Significant value can be added to ore supplied from the mine to the mill by measuring its quality in real time and performing grade control additional to that within the mine. Responsibility for ore quality between the mine and mill stockpiles is not always clear due to operational siloes so geologists and mining engineers need to be involved collaboratively with metallurgists to optimise ore value prior to processing. Sensors, such as the GEOSCAN-M which utilises high specification Prompt Gamma Neutron Activation Analysis (PGNAA), that measure conveyed ore flow representatively (continuous and fully penetrative) and in real time have been used in the minerals sector since 2003 and have been successfully applied in multiple commodities. Quality can be measured within the mine where material is conveyed underground or in-pit. Bulk ore sorting is used to divert increments of waste from the ore stream to upgrade material sent to the crushed ore stockpile (COS) as well as to create run-of-mine (ROM) stockpiles of different qualities to maximise blending opportunities and accommodate processing priorities, eg blending out deleterious content. The real time composition measurement can be combined with moisture and fragmentation analysis data for improved ore type characterisation, to control ore blending, for feedback to the mining schedule and block model reconciliation, and feed forward control for grinding and processing operations. The paper discusses various parameters measured and derived in existing operations that are used to maximise coarse waste rejection and metal recovery, optimise plant feed quality consistency, and reduce consumables; power, grinding media, water, reagents, and minimise fine tailings generation. Innovative geometallurgy applications are also discussed.

Mar 22, 2022

By Y Chung, B Choi, H Lee

Numerous studies have explored refractory corrosion in the presence of slag and/or metal, utilising the Finger Rotating Test (FRT). Recent experimental results revealed that corrosion initially increased with rising rotation velocity but was then suppressed above a critical rotating speed, under conditions involving a two-liquid solution of slag and molten steel. This phenomenon indicated that the liquid/liquid interface movement occurred during spindle rotor. However, understanding of the phenomenon, known as the rod climbing effect, remains inadequate in the case involving slag, molten steel and refractories. To gain deeper insights, a simulation experiment was conducted on the phenomenon using silicon oil/water and the phenomenon was analysed using computerised simulation software (Ansys Fluent). Experimental modelling demonstrated that interfacial movement occurs even at low rotation velocity, as low as 200 rev/min, when the viscosity of silicone oil is at 100 cP. Computational analysis utilising the Volume of Fluid (VOF) method and a realisable k-ε turbulence model elucidated that interface elevation during rotor rotation arises due to viscosity disparities between the two fluids. Furthermore, this movement is more pronounced when the viscosity difference is lower. Additionally, the study findings suggest that higher density differences between two liquids suppress the phenomenon of interface movement.

Jun 19, 2024

By H Kim, J Park, J Lee

Silico-ferrite of calcium and aluminium (SFCA) is a bonding phase in the iron ore sinter. The phase transition upon melting of SFCA was investigated with Differential Scanning Calorimetry and Confocal Laser Scanning Microscope. The initial melting of SFCA occurred at 1183.2°C and a massive melting was found at around 1351.1–1358.2°C. A phase transition-melting was investigated at 1476.5–1478.7°C. The liquid phase was composed of immiscible phases. The present results would be utilised to design a new iron ore sinter for better processing performance in a hydrogenenriched ironmaking process.

Jun 19, 2024

By D Woolmer

Since January 2019, BHP Olympic Dam have been trialling the use of a drone based LiDAR mapping system for the purpose for surveying stope voids. This new technology utilises Simultaneous Location and Mapping (SLAM) algorithm providing positioning, stability and collision avoidance in GPS denied environments. Implementation of this system utilised underground personnel trained in the equipment’s use. The study’s intention was to evaluate the effectiveness of this equipment versus traditional surveying methods in regards to quality, safety and productivity. The trial results showed a marked improvement in the quality, productivity and personnel safety when conducting surveys. The use of the drone and LiDAR system reduced personnel and equipment requirements for surveys, thus allowing these resources to be deployed elsewhere. The technology’s simple and rapid deployment allowed multiple surveys to be conducted during a 12 hour shift, including ad-hoc work with minimal disruption to underground operations. After the drone’s initial trial, further work was conducted to utilise the Hovermap LiDAR scanner on other platforms to increase utilisation. A mounting system was created allowing the LiDAR to be mounted on a remotely operated loader or vehicle. This enabled drawpoint scans to be taken directly after production completion, resulting in faster stope close outs and drive scans for convergence monitoring. Implementation of the LiDAR system has resulted in improvements in the stope production cycle by reducing delays previously associated with data capture. The increase in the volume and quality of data has also allowed in-depth back-analysis of stopes in new mining areas to be conducted, which have driven improvements in the design process.

Mar 15, 2021

By O Dominguez

Mine value chain reconciliation (MVC) is a necessary procedure to evaluate a mine’s performance against the assumptions and models used to plan mining and processing operations. Using nomenclature from Parker (2012), F2 reconciliation is the ratio between material received at the mill, compared with material sent to the mill, commonly reported in terms of tonnes, grade and metal. Measurements of material sent to the mill can be estimated in many ways, including: fleet management system (FMS) records, truck counts, or volume reduction. Most time-based reconciliations (for example, month-end reconciliation) use short-term model depletions of in situ rock measured by periodic topographic scans or surveys.

Mar 22, 2022

By D Abbott

Mining in Western Australia places significant economic and environmental responsibility on Government and the mining industry. Groundwater abstraction is regulated by the Department of Water. The Department has recently issued a guideline for Pilbara mines, and this paper focuses on the Pilbara for its examples and studies. The guideline is intended to form the basis for developing a statewide policy, consistent with reporting and assessment policy.With rapid expansion of the mining industry between 2005 and 2008, the groundwater resources in the Pilbara region of the State are under increasing pressure. Significant new management and regulatory issues arising recently include: cumulative impact assessment; disposal of dewatering excess by discharge, sharing or reinjection; life-of-mine approvals and closure planning; closure water quality including metals concentration in pit lakes; and in situ leaching mining methods and their impacts on regional water resources (and change of State Government Policy with respect to uranium mining).

Jan 1, 2009

By C L. McIntosh

The west coast of New Zealand’s south island is host to a large number of placer goldfields that stretch from the Westport area in the north to Gillespies Beach in the south and inland to the foothills of the Southern Alps. This area is host to a large number of alluvial, glacial and strand line deposits ageing in range from Recent to Tertiary. In recent years exploration models have been developed for off shore placer deposits on the continental shelf.Gold mining on the west coast has exploited placer gold resources from the 1860s to present, and with the recent surge in the gold price the industry is currently undergoing a resurgence. The current increase in mining is dominated by small-scale mechanical operations usually involving one to two people at each site; a few larger operations also exist such as the Grey River Dredge.Mining methods range from using floating bucket dredges to small diggers. Some of the mining technologies used are similar to those employed during the great gold rushes of the 19th century. Exploration and grade control techniques can be very rudimentary often relying on previous sampling programs or wide spaced bulk sample drill holes. Some bulk sample drilling is used on the larger operations as a form of grade control, most of the small operations tend not to use any ore control sampling prior to mining. Extraction techniques relying on simple gravity based designs with riffle tables or spirals are the most commonly used. Environmental standards are very high within New Zealand and require operators to return mined areas to preagreed to landforms. The high rainfall experienced on the west coast causes challenges to operators in regard to water quality. Technical issues combined with often limited capital provide for challenges to the operations.

Aug 22, 2011

By J Wheeler

The benefits of fine size separation in magnetite concentration are detailed focusing on published research from various iron ore producers. Basic principles of fine sizing and advancements in screening technology are addressed. A chronological review of research is used to show the evolution of fine sizing applications in the industry, starting with studies that demonstrated the benefit of using fine screens to produce consistent lower silica concentrates, followed by improvements in fine sizing equipment that have made effi cient screen classification in ball mill circuits practical. Case studies are used to demonstrate how positive sizing with screens can be used to significantly shift concentrate ‘grind/grade’ relationships.

Jul 11, 2011

By C Buchanan

For a long time there has been a known relationship between the northern Heavy Mineral (HM) deposits of the Murray Basin to the extensive north east trending ridges in the area. These ridges have been a targeting tool for exploration and have uncovered some significant discoveries, some of which have turned into mining projects. Bemax’s Ginkgo and Snapper deposits are good examples of how the faulting helped create an economic deposit but also result in significant planning issues in the exploitation of these deposits. Material balance, induration and pyrite issues have been made easier to manage through good geological understanding of the deposits.

Aug 22, 2011

By J J. Cilliers, K Hadler

Air is fundamental to flotation; not only is it required to collect the valuable particles, but it also controls the froth stability and consequently the separation performance for a given feed. Froth stability can be described and quantified in numerous ways, which are subtly different. Air recovery is one such measure of froth stability which accounts for both the stability of the bubbles and the mobility of the froth. The benefit of using air recovery as a measure of froth stability is that it exhibits a peak as air flow rate is increased, and this corresponds to the air rate at which the optimal separation performance is obtained. As such, it provides a single target value for optimising air flowrate for a given set of feed conditions. Use of air recovery, however, has one potential drawback: accurate measurement of the inlet air flow rate to a flotation cell is required. This can be problematic for operations, particularly where calibration of air flow rate is carried out infrequently or where there is no air flow rate measurement, such as for many self-aerated flotation cells. To this end, we present an alternative method for determining the peak in air recovery (PAR) air rate.We introduce a simplified method for determining the PAR air rate using trends in froth velocity and overflowing froth height, both of which are readily measured using existing froth image analysis systems. We will show, using industrial data, the application of this simple technique to find the optimal air flowrate for flotation cells. We will also discuss other alternative techniques for air rate optimisation that have the potential to improve separation performance using existing technology.CITATION:Hadler, K and Cilliers, J J, 2018. How to find the optimum air rate for flotation cells, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Grossi M, Baiden G

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and on- site applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no de- watering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

In this paper, three types of value-adding in the minerals industry are discussed: downstream processing, improving the efficiency of existing processing and increasing the knowledge base and expertise of the staff. It is shown that, while downstream processing seems to offer a good way of improving Australia's trade position, there are a number of impediments to such development, notably, limited access to the appropriate technology and overseas markets. Transport costs can also be a problem. To reverse the situation will require more positive policies by government. In the meantime, something can be done towards adding value by increasing the efficiency of existing processes. Examples are given, showing how it might be possible to make economies in reagent costs in the gold industry, how innovative technology has led to more complete processing of a tailings dump, how research might lead to an increase in the throughput in the production of synthetic rutile and how it is possible to leach selectively from gold/copper ores.

Jan 1, 1995

By T D. H McGrath, R Byleveld, W P. Staunton, J J. Eksteen

"The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has recently developed the integrated liberation leach model (ILLM) for optimisation of gold plants. The model encompasses recovery by both gravity (batch centrifugal concentrators or BCCs) and leach adsorption (CIP/CIL) circuits. The ILLM essentially combines the Group’s well-known standalone models (ie gravity and SIMCIL) to create a robust simulation package.The ILLM process model provides a tool for sites to determine optimum set points for operations to optimise recovery (eg target grind size). It can also be used to predict the effect on gravity recovery, leach recovery and overall recovery when changes are made to circuit design, either temporarily (eg a leach tank taken off-line for maintenance) or as part of a circuit expansion (eg expanded gravity circuit capacity, or addition of leach tank capacity).This paper discusses the capability of the ILLM process model by highlighting a recent case study. The paper also addresses the test work and plant data required as model inputs, as well as limitations and the application of the ILLM to greenfield projects.Citation:McGrath, T D H, Staunton, W P, Eksteen, J J and Byleveld, R, 2016. Application of an Integrated Liberation Leach Model for Process Optimisation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Underground excavations are subjected to complex stress changes caused by nearby mining, but may also be affected by repeated dynamic loading from blasting and seismic events. In some cases, the combined, cumulative effects can lead to unforeseen damage, displacement and instability. Simulating dynamic loading of an underground excavation is a very complex task. The state of rock mass stress, damage and deformation must first be simulated sufficiently requiring small-scale structures to be explicitly modelled. Supporting elements must be represented with high similitude and then the dynamic event must be applied to the system in the case of blasts, or evolve as a consequence of rock mass instability for seismic events. A special case is for the effect of pit blasting on underground excavations - discontinuous rock phenomena at scales from mine, to bench, to pillar, to tunnel need to be captured and this represents one of the most computationally intensive tasks in mine simulation. Recent advances in computer power allow these tasks to be completed at a mine scale, incorporating discontinuities and geological detail matching the best practice for static Finite Element analyses. The results are a worthwhile contribution to mine decision-making, but require careful interpretation and thoughtful inputs - even more so than quasi-static analysis - as the cumulative effects of unfavourable modeling practices are greater. Some learnings from experiences with mine scale, discontinuum dynamic simulation are summarised, including a discussion of considerations of scale and similitude for this type of analysis.

Nov 25, 2010

By J Webb

"It is vitally important in projects where the cut-off grade is low that there is no contamination during the sampling and sample preparation process, both in the ore and the waste zones. Failure to identify contamination could have devastating financial consequences for a project. The use of a variety of blank types is essential for ensuring that contamination is identified and eliminated at every stage of the sampling and sample preparation process. This paper examines an instance where an effective assay quality assurance and quality control (QA/QC) program was able to identify and eliminate a source of significant multi-element contamination in the prefeasibility stages of an open pit project. This examination includes the: evidence for contamination findings of the investigation process of resolving the problem and correcting the data evidence for both addition of metal and dilution through contamination potential impact on the project had this issue not been dealt with. It was through the use of a combination of blank types that the QA/QC process at Mount Isa Mines (MIM) identified a contamination issue at the first crushing phase of sample preparation. Identification of the contamination allowed MIM to stop assaying activities and work with the laboratory to correct the problem. The sampling program could then be continued with no further doubts about the sample preparation process. Contaminated samples were resampled from retained core. With the continuous monitoring provided by the blanks program, it was possible to ensure that only clean results went into the resource modelling data set. CITATION:Webb, J, 2014. When nothing is what you need – the importance of using blanks at all stages of sample preparation, in Proceedings Sampling 2014 , pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

Dust emissions from mining, material processing and ship loading operations (fugitive dust sources) are an environmental issue of increasing concern to both government regulators and the community. The main concerns relate to potential amenity, health and environmental impacts from the emissions. Therefore it is imperative that mining/ processing operations, as part of their overall environmental management, reduce fugitive particulate emissions to as low a level as is practicably possible. This technical paper outlines the mechanisms that lead to fugitive particulate emissions, the importance of understanding the exact cause of fugitive emissions, monitoring methods that can be used to quantify the emissions from specific sources, the use of atmospheric dispersion modelling in dust management and innovative dust management strategies including predictive meteorology and proactive management.

Jan 1, 2009

By A S. Derrington

In some parts of Australia, mine air cooling may not be needed until a depth of 1300 m below surface is reached. In other locations, it may be essential at a depth of only 300 m below surface. The reasons for these differences are multifaceted. This paper discusses the main factors and describes a simple method to assess whether or not mine air cooling will be required. The method uses a graphical relationship that considers depth below surface, geothermal gradient, surface climatic conditions and directness of the mine intake routes. This relationship has been developed, tested and refined over a period of more than ten years using data collected from most of Australia’s deeper metalliferous mines. The method provides a ‘first-pass’ indication of whether more detailed cooling studies may be needed. Perhaps more importantly, the method’s underpinning by benchmarking against other mines improves confidence in the assessment results. Like any empirical method, the context must be understood and this aspect is also discussedCITATION:Derrington, A S, 2014. Will your mine require cooling?, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 181–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

Mine site rehabilitation is the repair of the disturbance caused by mining on the immediate mining area and also on the surrounding environment. The long-term objectives of rehabilitation can vary from simply returning an area to a safe and stable condition, to restoring the mined land to a state as close as possible to its pre-mining condition, capable of being self-supporting and having a beneficial final land use. This paper investigates the importance and benefits of environmental planning, in particular for rehabilitation, and how input into daily operations can allow mining to progress with limited impact on the surrounding environment. It will also identify some of the key mistakes currently made during mining which could be averted by implementing prior planning and incorporating environmental consideration into daily operations. A number of rehabilitation opportunities will also be detailed for the different stages of the life cycle of a coal mine.

Jan 1, 2007

By C A. Foss, K Leslie, C Arnold

Magnetic susceptibility measurements provide rapid, non-destructive testing of drill core, but cannot directly map magnetite and/or hematite content. Combined magnetic susceptibility and magnetisation measurements provide much more diagnostic information and, with sparse calibration constraints, are able to quantify magnetite and hematite concentrations and potentially map differences in grain size and texture. We have developed a travelling three-component vector magnetometer that can be run alongside core to map its external magnetic field. The logger has been designed to operate in core sheds and at remote drill sites. It is used to rapidly scan a length of core, with each core being scanned in different rotations. The magnetic field contributions from any remanent magnetisation rotates with the core and cause differences between successive measurements, while the field contributions from any induced magnetisations with isotropic magnetic susceptibility remain constant. Deconvolution of the magnetic field data with simultaneous three-channel inversions of the multirotation data separates remanent and induced components. Interpretation of this data provides estimates of the intensities of induced and remanent magnetisations, the orientation of the remanent magnetisations and the ratios of the induced and remanent magnetisation strengths. We expect these magnetisation parameters to correlate with stratigraphy through a banded-iron formation. Furthermore, we anticipate that we will be able to use this information to map zones of oxidation and other changes along the core. This novel instrument is one component of an integrated CSIRO program to provide new capabilities for iron ore exploration and development based on studies of magnetic fields and magnetisations at scales ranging from centimetres for these core investigations to tens of kilometres for formation studies.CITATION:Foss, C A, Leslie, K and Arnold, C, 2015. Rapid logging of different magnetic phases in banded ironstones using a travelling three-component vector magnetometer, in Proceedings Iron Ore 2015, pp 271–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Various methods and software have been trialled for simulation of Au grades at Boddington Mine. This covers in-house and public software as well as sequential and turning bands methods. The diversity of options was further expanded with comparison of point and direct block simulation. Some difficulties were encountered in incorporating high-grade restrictions. Altering parameters or software can make very significant differences and give results varying from estimations. This paper details a new simulation run with validation and tests for local calibration (or progressive correction) of the simulations to the estimations, focusing on reproduction of statistics. This approach brings to the forefront the question æwhat is the purpose of the simulations?Æ Results and some ideas for future applications at Boddington are summarised.

Sep 26, 2011