Search Documents

By B. F. Peters, J. Gordon Parr, E. R. Macgregor

A SERIES of seven hypoeutectoid alloys, up to 18.2 atomic pct Mn, was made by the levitation melting technique. The loss of weight on melting was considered to be entirely due to volatilization of manganese, and compositions were computed on this basis. Filed samples (—200 Tyler mesh) were helium quenched from 1000°C after soaking for 5 min by a technique already described.' Quenched Alloys -Assessments of the amounts of a phase produced and the hardness of the quenched alloys are summarized in Fig. 1. The experimental techniques and calculations involved have been described previously. The amount of a decreases as manganese content increases, until at 10.6 pct Mn only a trace of a' is observed. Previous

Jan 1, 1957

By Thys B. Johnson

Traditional mine planning concepts are discussed and suggestions for improvement through use of the developed model are proposed. The approach developed in this paper allows optimal planning of the complete mining-concentrating-refining system over the entire planning horizon and permits the system to dictate how and when to process a block of material, i. e., a dynamic cutoff.

Jan 1, 1969

By A. G. Paithankar, G. B. Misra

Although certain physical mechanical properties of rocks have been claimed to give an estimate of penetration rate in percussive drilling, the authors' work shows that the correlation of penetration rate with individual rock properties is Poor. The authors have developed a good correlation between penetration rate and a set of rock properties but the relation is complex. Energy per unit volume has been used as a measure of penetration rate in percussive drilling by Hustrulid and Fairhurst; however, their test setup is large wing a full size drill bit. The authors determined the minimum energy for unit volume Ev min for any rock at the optimum index angle in a simple laboratory drop tester wing a sharp microbit with a tip angle of ll0°. This Ev min has been found to correlate well with penetration rate obtained in controlled laboratory drilling in different rocks for different stages of bit wear. A comprehensive relation has been developed between penetration rate and Ev min.

Jan 1, 1981

By C. Dinis da Gama

In order to reduce the complexity of mechanisms influencing rock. fragmentation by blasting a simulation approach is proposed, using the capabilities of microcomputer interactive graphics. Situations involving cratering end bench blasting are simulated, and both jointed and intact rocks can be subjected to explosive action, taking into consideration its breakage mechanisms. Size analysis curves relating rock distribution before and after the blasts are determined and compared with field data.

Jan 1, 1984

Jan 9, 1951

Jan 1, 1940

By Roy J. Greenfield, Charles H. Stoyer

A geophysical survey was made in Kylertown, Pa., in an area where the ground water is polluted with acid mine drainage. Since acid mine water is a good electrical conductor, both direct-current electrical and electromagnetic loop methods were examined for their ability to determine the subsurface electrical conductivity structure and from this to imply the location of the acid water. Consistent results were obtained with the two methods and the interpreted subsurface resistivities were consistent with the electrical resistivity measured for water samples. It was demonstrated that fracture traces which act as conduits for ground water flow can be located with electromagnetic surveying methods. Thus geophysical methods for measuring subsurface electtrical resistivity can be used to advantage for monitoring the environmental impact on the ground-water system of acid mine water.

Jan 1, 1977

THE CHAIRMAN (H. W. MORSE, Los Angeles, Cal.).-I would like to open this meeting for a little while to the general subject of leaching. We ought not to hold back if we have any new schemes for the future. I know that those of us who are tangled up with this lei thing work will appreciate any suggestions that will make us work harder and, scheme, harder to pull through these past difficulties on leaching. F. S. SCHIMERKA, Clifton, Ariz.-Under the direction of J. W. Bennie, General Manager of the Shannon Copper Co., Clifton, Ariz., 'it has been my valued privilege to cooperate in the elaboration of a hydrometallurgical process aiming at the recovery of copper in mill tailing resulting from a gravity concentration of a low-grade semi-oxidized sulphide ore occurring in a porphyritic gangue. The experimental work which has been carried on with a 25-ton plant is completed, and the company is building at present a leaching plant on a larger scale, the first unit consisting of a 150-ton roasting furnace and accessories for leaching the calcine.

Jan 12, 1916

Jan 1, 1891

Sixteen executives, technicians and operative personnel from the French mining industry, now touring mining operations in the U.S., will wind up their visit to this country at the AIME Annual Meeting. Traveling under ECA auspices, they will be in Denver on Feb. 5, Salt Lake City, Feb. 8 to 13, Bonne Terre on Feb. 16. Four of the group are engaged in bauxite mining, nine in lead and zinc, two in pyrites mining. All are interested in American mining equipment and methods, and hope to contact manufacturers' representatives in the various areas they visit. A $600,000 manganese pilot plant is expected to be put into operation by Sept. 1, by the Bureau of Mines at Boulder City, Nev. S. R. Zimmerly, chief of the Bureau's metallurgical div. for the region, recently completed the mill design and flow sheet; and the Bureau is awaiting steel priorities before building. Ore from the Artillery Peak area, 60 miles south-west of Kingman, Ariz., will be used in the mill. Construction will be handled by Rex Lloyd of Boulder City.

Jan 2, 1951

The age of specialization has made man increasingly dependent on a larger number of different metals and minerals. Overexploitation during World War II and lavish squandering of irreplaceable mineral wealth in the past has resulted in the rapidly approaching exhaustion of some of the major domestic ore sources. History clearly points out that the United States cannot continue to be a world power on an "import to survive" policy. A constructive program of development and appraisal of the nation's mineral wealth, including the planned conservation of her resources, must be adopted. Strictly speaking, conservation of minerals must mean the orderly exploitation of our resources and the prevention of waste in use, with due regard for the future. Real concern for the future may not extend beyond a few generations. Eventually science and invention should take care of the problems arising from shortages of some minerals, and the national defense aspects of domestic deficiencies can be provided for by stock piling and other measures. Early conservationists had this viewpoint; but with a rapidly developing industry and population, a farsighted policy that would deny full realization of immediate ambitions became unpopular. Consequently, the politically minded conservationist broadened the concept to include "prudent use of resources" and brought under the conservation umbrella

Jan 1, 1950

By S. K. Nicol, A. R. Swanson, J. C. Day

Addition of oil to a suspension of hydrophobic coal particles can influence its dewatering characteristics. An agglomeration process occurs in which coal particles are held together by negative capillary pressure at particle/oil/water contacts. Consequently, the units round which flow can occur are enlarged and this improves dewatering parameters such as drainage rate, solids recovery, and equilibrium moisture content. This paper discusses processes which attempt to use this principle, in terms of metallurgical and economic efficiency. The discussion is augmented by results of recent experiments on the effect of oil addition to centrifuges and vacuum filters.

Jan 1, 1980

COUNCIL OF SECTION DELEGATES Nicholas A D'Arcy, Jr, Chairman (Southern California Section) Charles Chapman, Vice-Chairman (Florida Section) Ben H Parker, Secretary (Colorado Section) Frontier Refining Co Boston Bldg Denver 2, Colorado

Jan 1, 1956

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200°C, a wide range of conveyors is available. Special constructions of rubber conveyor belts. steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400°F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F.

Jan 5, 1953

By O. C. Wheeler

The activity in exploration and in the acquisition of prospective oil lands that reached such a high level in Colombia during 1936 gained momentum and reached unprecedented proportions during 1937. Both national and private lands were taken up. In the Magdalena Valley above Puerto Berrio, leases on large tracts of private lands are held by Richmond (Standard of California), Shell and Texas. Tropical also owns leases covering a block of acreage in this area near Honda. From Puerto Berrio to El Banco most of the acreage is of national ownership, and concessions covering parts of this area have been granted to Tropical, Socony Vacuum, Shell and others, while applications for additional concessions are pending. Latterly leases on private lands below the Lebrija River have been taken out by Shell and Richmond. In the drainage basins of the Meta and Guaviare Rivers of the Llanos region of eastern Colombia, several of the major companies have carried on geological exploration and it is understood that some private properties have been leased or optioned. Under Colombian law, subsoil rights are reserved to the nation on all lands that passed from Government ownership after Oct. 28, 1873. Private titles antedating that day carry both surface and subsurface rights. Conditions under which lands may be acquired, explored and

Jan 1, 1938

By G. Carman Ridland

Front Range, Colorado: The majority of the rocks comprising the Front Range of Colorado are pre- Cambrian schists, gneisses, and intrusives which have been elevated to form part of the Southern Rocky Mountain physiographic province. The region is noted mainly for its production of gold and silver, but ores of tungsten, fluorspar, uranium, copper, and iron have been worked. Geological literature describes pitchblende and other radioactive minerals occurring at Jamestown, Boulder County; Central City, Gilpin County; and Lawson, Clear Creek County (fig. 1). These three adjoining counties cover most of the highly mineralized section of the Front Range which extends from James- town to Breckenridge. As far as the writer is aware, uranium has been found only in the portion north-east of Lawson.

Jan 1, 1950

By Theodor Knutzen, Charles H. Fulton

The plant of the National Smelting Co., a corporation controlled by the Horseshoe Mining Co., was built during 1901 to smelt the dry siliceous ores of the northern Black Hills, extracting the gold- and silver-values in a matte of low copper-percentage which is shipped to Omaha and Denver for refining. Originally, the plant was designed to collect the values of the siliceous ores in an iron-matte, which mas to be resmelted with lead-ores, in a lead-furnace, the lead-bullion produced to be refined into Doré bullion in English cupelling-furnaces. However, the scarcity of lead-silver ores in the Black Hills, owing to the present non-productiveness of the Galena district, led to

Jan 1, 1905

By Y. C. Kim, I. K. Chopra, F. Martino

This paper reviews geostatistical work in a coal deposit performed jointly by the University of Arizona and the Homer City Owners. The study objective was to Predict more accurately the inseam sulfur values of the deposit for the purpose of future emission control. Based on initially available 112 DDH information, variogram models were developed for sulfur, ash, and thickness for the entire deposit. The deposit was then kriged using 333 m x 333 m panel size. Kriging produced better results than conventional isopachs. The estimation variance information obtainable from geostatistics was then used to improve development drilling activities that were underway. This effort was successful. Up-to-date experience on the use of conditional simulation of the deposit appears promising for future emission control strategy development

Jan 1, 1982

By Harlan A. Walker

Rock-drill steel has an important bearing on costs in many mining operations, both directly and indirectly. Direct factors include such items as shop expense, steel consumed per ton of ore produced, cost of distribution and the dust hazard. The latter, although no specific amount may be assigned to it, is an ever-present problem, and is receiving increased attention as the science of mining progresses. Indirectly drill-steel performance affects consumption of compressed air, maintenance of drills and drilling speed. The latter, in turn, increases or retards the tempo of mining and development. These factors, while not all inclusive, are preponderant in their importance. Thus it is evident that in an extensive operation drill-steel expense may run to many thousands of dollars and that thoughtful research leading toward more efficient practice is warranted. Experimental Work During the late spring of 1939, experiments were undertaken at Homestake in reducing changes in drill-steel gauge from ? in. to 1/16 in. In drifts and crosscut headings mounted machines were set up and holes were drilled with ?-in. bit-gauge changes and other holes a few inches

Jan 1, 1940

Jan 1, 1941