Search Documents

By Thomas M. Barczak

The era of the shield-supported longwall face began in the United States a little over 25 years ago. The most fundamental development of the shield in the past 25 years has been an increase in size and capacity and a progression toward two-legged designs in favor over four-legged shields. Is the ?bigger-the-better? design philosophy justified? The advantage of the two-legged design is largely attributed to its active horizontal force caused by the forward orientation of the leg cylinders. How do we know this? You might be surprised to learn that shield loading data may suggest otherwise. In addition, what about setting pressures? Should they be set as high as possible? Some people have advocated that setting pressures should equal the yield pressure. Does this make any sense? Is yielding a good or bad thing? These are some questions still worthy of investigation that are addressed in this paper. The first major change in gateroad support was the use of cable bolts to replace conventional wood cribbing particularly in Western mines. Standing support changed very little until the mid-1990s, when Strata Products1 introduced the Hercules and Propsetter supports in Eastern mines and Burrell Mining Products introduced the Can support in Western mines. Since then, there has been a dramatic increase in new roof support technologies for longwall gateroad support. Historically, standing support, including shield supports, have been designed based on a simplistic model requiring the support to have sufficient capacity to support the gravity loading of a perceived detached rock mass. This approach ignores the stiffness of the support and the resulting ground deformation that is known to be critical to roof stability. Recently, a new approach based on the ground reaction concept has been promoted by the National Institute for Occupational Safety and Health (NIOSH) to account for the interaction of the support with the rock mass behavior in achieving ground stability. In addition to gateroad support design, this concept has ramifications for shield capacities, setting pressures, and recovery room support design that challenge current practices in these areas. Although longwall mining has matured into the safest and most productive underground mining method used today, traditional concepts of roof support design and practice should still be evaluated and challenged. Ultimately, advancements in the science of ground control are made by recognizing deficiencies in current theories and thinking outside the box.

Jan 1, 2006

By R A. Lynch

The state-of-the-art in cave seismic monitoring is reviewed, with the latest developments in active seismic monitoring included. Seismic monitoring systems are routinely used by most of the world’s block and panel caving mines to track the cave initiation and progression. The current best practice is to use the cloud of seismic event locations as a proxy for cave growth somewhere below. Problems with event location reliability due to seismic ray bending around the (unknown) cave are side-stepped by using sensors installed above the cave. However, the aseismic gap – the (unknown) distance between actual cave back and seismic event cloud – currently hinders reliable estimation of cave geometry.Velocity inversions using the passive seismic data are inexpensive and should be undertaken more routinely. The straight-ray methods should be used with caution, as the underlying assumptions are invalid in caving environments. The double-difference method is more correct for the caving situation, and there have been some promising results published. Constrained geometric inversions make a lot of sense, but have yet to be demonstrated successfully.Two active seismic source have recently been developed for use in the caving environment: a piezoelectric source for ranges up to a few hundred metres and a pneumatically-powered source for ranges up to a kilometre. These sources produce signals on standard mine seismic sensors that can be used to measure seismic velocity variations down to 0.01 per cent resolution. This allows the cave progression to be monitored by measuring tiny changes to seismic velocities as the rock above the cave is fractured and destressed.CITATION:Lynch, R A, 2016. Active and passive seismic monitoring of cave front evolution, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By H. A. Wright

This report assesses the economic, legal, institutional and technical factors that affect the current and future status of implementation of mine monitoring systems in the United States. It begins with a description of a poll of the Mining Production Research Committee and the Mine Monitoring and Communications Committee of Bituminous Coal Research that was conducted to establish industry monitoring needs and constraints. Existing systems in the United States and foreign countries are then reviewed and compared with the requirements set forth by the industry committees. At the same time, state and federal mining laws are reviewed, and equipment currently available from suppliers of mine monitoring systems and components is discussed. A framework for cost/benefit analysis is established and a series of case examples for various monitoring functions are presented. The total values of the market for mine monitoring systems in 1980 and 1990 are estimated on the basis of industry statistics and system cost estimates.

Jan 1, 1982

By R. H. Sprute

This report describes Bureau of Mines laboratory test results in electrokinetic dewatering and consolidation of metal-mine tailings. Tailings were placed in 0.3-cubic-foot Plexiglass models, and dc potential was applied until dewatering ceased. Time-oriented measurements of water removal, changes in resistivity, and power consumption were recorded during the dewatering process. Dewatered material was tested for moisture content and density. Equipment and procedures were developed to optimize the method for unclassified mill tailings from a particular mine in the Coeur d'Alene, Idaho, district. Results indicate the method to be highly effective in dewatering and consolidating this material.

Jan 1, 1974

By A. Kale

A chlorination pilot plant having capacity to produce 5?10 kg/hr of titanium tetrachloride is in operation at the chlorination facility in Mintek. The bubbling fluid bed chlorination plant can be operated in batch and/or continuous process to study the chlorination kinetics of various feedstocks. The chlorination of titaniferrous ores to produce titanium tetrachloride (TiCl4) was carried out during the commissioning of the pilot plant and also as part of the titanium programme carried out at Mintek. TiCl4 is a basic raw material for producing commercial titanium dioxide pigment and titanium metal. This paper discusses the challenges faced during the commissioning and operation of the chlorination pilot plant. It also discusses the effect on the auxiliary facilities and instrumentation as a result of the harsh operating conditions of +1000°C and use of corrosive gases like chlorine and titanium tetrachloride. It discusses the effect of physico-chemical properties of the titanium tetrachloride and iron chlorides. The effect on the chlorinator refractory lining due to heating and cooling of the chlorinator is also discussed. Besides the special provisions made during the design of the chlorinator, this paper also discusses the operational experience and possible solutions to be implemented in future. Keywords Fluid bed chlorination, titanium ore chlorination, titanium tetrachloride (TiCl4) production using fluid bed technology.

Jan 1, 2011

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce energy consumption, thus contributing to the reduction of green house gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. Extended to the Canadian mining industry, such results would represent a GHG emission reduction of about 0.05 Mt/y. A soft-sensor prototype, based on primary crusher data (i.e., energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory-testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e., use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2008

By W. R. Leeder

"The Quintette coal property lies in the Rocky Mountain foothills of northeastern British Columbia (see Figure 1). Quintette and the adjacent Bullmoose property of Teck Corporation are soon to become the first commercial coal mines in the Peace River Coal Field, which is estir1ated to contain 10 billion tonnes of metallurgical coal reserves.Denison Mines Limited acquired the original Quintette coal licenses in 1969 and 1970. Exploration began soon after and the first feasibility study was conducted in 1975. Denison devoted the following six years to extensive planning and feasibility studies of the project. During this period, the provincial and federal governments also undertook studies to assess infrastructure requirements and economic viability of development in this part of the province. Many of the proposed mine sites such as Bullmoose and Quintette were at least 100 to 150 kilometres from the towns of Chetwynd and Dawson Creek, the nearest centres serviced by good highways and a railroad, and a complete network of services would have to be provided if such mines were to be developed. The overall project became known as the North East Coal Development.Concurrently with the feasibility studies, numerous technical and sales missions to Japan were made by representatives of Canadian industry and government, culminating in January 1981 with agreements for Quintette Coal Limited and Teck Corporation to supply a total of 115 million tonnes 8 million tonnes per year for 15 years of primarily metallurgical coal to the Japanese Steel Industry."

Jan 1, 1983

By G. Le Bel

The paper proposes three methods to determine optimum lifetime of a mining project1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: • It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. • The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate.

Jan 1, 1993

By Rajiv Kalra

This paper reviews the following aspects of the world?s largest manufactured Grinding Mill?s in terms of diameter and power, along with the world?s biggest shop assembly and trial run of the mills delivered to Sino Iron Magnetite Project in Australia. 1. An overview of the basic flow sheet of the Sino Iron (Magnetite) Project located in Australia 2. An overview of in-house designed CITIC Heavy Industries 12.2 m (40ft) F x 11 m(36ft) LG ? 28MW AG mills including FEA and major components 3. In-house manufacturing at CITIC-HIC work in Luoyang China of all major components for 6 off Ø12.2 m(40ft) AG mills and 6 off Ø7.9 m(26ft) x 13.6 m(44.6ft) LG-2 x 7.8 MW Ball Mills 4. Major aspects of design and preparation of the biggest shop trial run of Ø7.9 m(26ft) x 13.6 m(44.6ft) LG Ball Mill witnessed by international EPCM?s and clients in July 2009. 5. Major aspects of one piece assembly of 1300 tonne rotating element of the Ø12.2 m(40ft) x 11 m(36ft) LG AG Mill and Ø7.9 m F (26) x 13.6 m(44.6ft) LG Ball Mill at the port of the export China and transport to Australian Port and then to site. 6. An insight to unique installation methods used for Ø12.2 m(40ft) and Ø7.9 m(26ft) rotating element lifting on the mill foundation in one piece assemblies. 7. CITIC Heavy Industries present capability for in house design and manufacture of Grinding Mills up to Ø13.7 m (45 ft) with 35 MW Gearless drives and Ø12.2 m(40ft) with 2 x 10 MW Geared Mill drives

Jan 1, 2012

The goal of the Bureau of Mines diesel engine research program is to reduce exhaust emissions and minimize the risk of fires and explosions caused by the use of diesel- powered equipment in underground mines. This program has led to a fundamental understanding of the problems and to solutions that allow diesel equipment to be used safely and effectively. This volume contains reports of the presentations made at the Bureau Technology Transfer Seminar on Diesels in Underground &fines given in Louisville, KY, and Denver, CO, on April 21 and April 23, 1987. It also contains three reports of related research, not presented at the seminar, which highlight the significant achievements of a joint US.-Canadian research program on diesel emission control technology for underground mines. Topics covered in this volume include discussions of industrial hygiene problems associated with the use of diesels, accident statistics, fire and explosion control systems, measurement of diesel pollutants, emission control techniques including engine maintenance, fuel additives, diesel particulate filters, and ventilation of diesel sections. An alternative to diesel power, the hydrogen-powered mine vehicle, is also described.

Jan 1, 1987

By T. Lux, M. Hanel, Degel, A. Filzwieser, R., H. Joubert

It is the increasing demand for an economic and cost saving operation mode that requires effective cooling in order to achieve low refractory wear and good furnace lifetime, which is making cooling technology an important aspect of furnace operation. In addition, the requirements for safety are getting more and more into focus. However, the use of water—today’s standard cooling medium—has major drawbacks as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion. Not to forget the severe risks for the operators as well as economical damage in case of a malfunctioning water cooling system. With this new and patented cooling technology ILTEC and the ionic liquid IL-B2001 as the cooling medium, it is possible to realise a water-free cooling solution and therefore the door is wide open to rethink existing and conventional cooling solutions. Furthermore, there is also the chance to recover heat from the process in a more efficient way. However, since the technology is novel and unique there are a lot of concerns and doubts regarding safety for plant operators and employees. The paper is intended to cover both: highlighting the enormous potential of the technology but also to eliminate concerns mainly caused by rumour and unawareness. INTRODUCTION All of us are aware of the risks when water is used as a coolant and placed in the vicinity of the liquid metal phase. Unsuitable design solutions or wrong operation modes of the furnaces or failures of refractories can cause a direct contact of water with liquid metal. The consequences can lead to equipment failures, vessel destruction but even worse to injuries and even fatalities. Over the past decades, countless incidences were reported. Fatal accidents caused by water coming into contact with liquid metal happen every year (Oterdoom, 2014; Filzwieser, Konetschnik, Filzwieser, Wallnerm & Preiss, 2014). With the novel ionic liquid cooling technology virtually all negative effects of a water cooled system regarding safety are eliminated and even additional benefits can be provided (Voermann, Ham, Merry, Veenstra, & Hutchinson, 1999;Verscheure, Kyllo, Filzwieser, Blanpain & Wollants 2006; Wallner, Filzwieser & Kleicker 2006). The fact that no explosion occurs when IL-B2001 gets in contact with molten metal results in a revolutionary solution for the metallurgical industry in terms of safety—new safety standards can be achieved.

Jan 1, 2019

By J. C. Willett, J. R. Sanfilipo, P. D. Warwick

The U.S. Geological Survey has conducted an assessment of the Nation’s coal deposits that potentially could be mined during the next 30 or more years. For the Gulf Coastal Plain region, the assessment includes reviews of the stratigraphy, coal quality and resources, and coalbed methane potential of the Cretaceous, Paleocene, and Eocene coal deposits in the region. The results of these efforts are a series of digital maps, text, and tables published in CD-ROM format. Although abundant coal resources are available in the Gulf Coast region, coal quality issues may limit large-scale development in the future. Additional data are required to better evaluate the coalbed methane resource potential for the Gulf Coast region.

Jan 1, 2001

By D. Denton, L. Buckingham

The dry grinding and leaching circuits of the Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs. Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes. The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper. The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility. Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike.

Jan 1, 2001

By R. L. Fullman, J. W. Cahn

A method is derived for obtaining the distribution of sphere diameters and plate thicknesses (or pearlite spacings) from size distribution functions obtained along randomly oriented lines. The method described offers several advantages over existing methods. IT is often of interest to measure not only the average particle size but also the distribution in sizes of particles dispersed in an opaque material, such as an alloy. Particles of a single size will exhibit a range of apparent sizes on the plane of polish. If the sample contains a distribution of particle sizes, the distribution of observed sizes on the plane of polish is related to the distribution of actual particle sizes by an integral equation, For example, a distribution of sphere sizes, N(r),

Jan 1, 1957

By Ike Madingoana, Stephan van Zyl, Antoine F. Mulaba-Bafubiandi

"The study presents a control strategy implemented at the Nkomati nickel mine flotation plant for process stabilization and improvement. The control strategy involves flotation concentrate volumetric flow rate stabilization and the flotation cell mass pull control. The flotation concentrate volumetric flow rate is operated at a fixed set point. The initial control strategy involved varying the flow rate to maintain the concentrate tank level thereby reducing pump cavitation. The flotation cells mass pull control comprises air rate manipulation into the cells with the exception of the recleaners. The air rate into cells is automated to adjust based on the concentrate tank level variation. The control strategy was implemented on the roughers, cleaners and the recleaner circuit. The recleaner cells air flow rate is adjusted based on the MgO content in the concentrate. The stabilization of the flotation concentrate volumetric flow rate and the mass pull by aerate automation will increase the scope of optimization for further process improvement. The immediate benefit of the control strategy implementation was plant stability. Disturbance to the flotation cells downstream was minimized due to stable flow rate, and the air addition manipulation ensured that the concentrate tank levels are maintained, minimizing pump cavitation. INTRODUCTION Froth flotation is a challenging process because it is influenced by a large number of factors, including the flotation feed characteristics. One of the ore types mined at Nkomati nickel mine is the main mineralized zone (MMZ). The MMZ ore is hosted in the Uikomst complex, a Ni-Cu-PGE-Cr- mineralized, layered basic to ultra-basic intrusion which hosts commercially viable magmatic base-metal sulphides (De Waal et al., 2001). The MMZ ore is a heterogeneous sulphide mineral resource with a varying sulphide mode of occurrence and texture. The beneficiation of the complex sulphide ore is challenging due to the presence of impurities in the ore. The impurities report to the flotation final concentrate and penalties are levied if the impurities are beyond the contractual limits."

Jan 1, 2015

By M. E. Poad, J. K. Whyatt, T. J. Williams

Researchers at the U.S. Bureau of Mimes monitored rock mass response to mining of an experimental underhand longwall stope in Hecla Mining Co.'s Lucky Friday Mine, Mullan, ID. This stope design, the Lucky Friday underhand longwall (LFUL), was proposed as a means of controlling rock bursting while also allowing increased mechanization of mining operations. Instruments were specifically manufactured to monitor three geomechanical factors (backfill performance, ramp stability, and rock mass response) that directly affect the success of stope design. Despite considerable difficulties with instrument installation and survival in the harsh mine environment, especially within the stope fill, sufficient information was collected to suggest that the LFUL method was successful in achieving project goals. This conclusion, in addition to favorable economic and operational evidence, led the mine to adopt the method throughout the mine. Indeed, this study and mining experience suggest that underhand longwall mining could be considered a feasible mining method for rock-burst-prone ground throughout the Coeur d'Alene District. Further Reports of Investigations (RI) in this series present in-depth analyses of the effects of backfill on rock bursting and calibration of a stope numerical model.

Jan 1, 1992

By L. K. Barker

The purpose of this research was to determine how much, if any, improvement would be made by subjecting hydrogenated shale-oil naphtha to a catalytic reforming process. Preselected ranges of temperature and pressure within the commercial reforming ranges were chosen for investigation and other possible variables were held constant. All tests were made with a liquid hourly space velocity (LHSV) of 3 volumes of liquid feed per volume of catalyst per hour (Vf/Vc/hr) and a hydrogen feed rate of 3,000 scf/bbl. Operating temperatures of 850°,875°, and 900° F were used at pressures of 200,400, and 600 psig. The greatest octane improvement in the naphtha was obtained at a temperature of 900° F and pressure of 200 psig. The reformed naphtha had a clear research octane number of 89, a liquid yield of 80 vol pct, and a yield-octane number of 71.1. The data indicate that a higher temperature could have produced a higher yield-octane number.

Jan 1, 1973

By P. T. Brooks

Mineral nodules from the ocean floor represent a vast potential source of manganese, nickel, cobalt, and copper. Process development studies to devise methods for recovering these metals were conducted by the Bureau of Mines using two types of nodules--relatively low-grade calcareous nodules from the Atlantic Ocean and higher grade siliceous nodules from the Pacific Ocean. Ammoniacal carbonate leaching of reduced nodules appeared to have the best potential for processing the calcareous nodules, but the method proved to be impractical for recovering manganese. Extraction of 90 percent or better of the nickel, cobalt, and copper showed the technique to be attractive for recovery of these metals. The siliceous nodules appeared amenable to a process that starts with either a sulfur dioxide leach or a sulfation roast followed by a water leach to dissolve the soluble sulfates.

Jan 1, 1971

By G C. Sen

All mining and quarrying operations that employ blasting to fragment and move broken ground have a price to pay for æby-productsÆ such as vibration and noise. These æby-productsÆ cannot be eliminated but they can be controlled and modern blasting techniques have improved to the point that excessive environmental restrictions can be adhered to whilst maintaining acceptable production rates and quality. Accurate measurement is the key to control, and as the environmental limits are becoming tighter, the proper way to measure vibrations from blasting operations becomes an integral part of the mining or quarrying operations. The basic vibration monitoring system consists of a primary sensor connected to a data logger and computer software for the analysis of the signal received and recorded. Currently, as with all fields of measurement, much improvement has occurred over the past decade, and electronic devices are much more accurate and reliable. Data analysis has also improved considerably with the computing power that is available to field operatives today. Mounting the primary sensor has been often overlooked in supposed æstandardsÆ with procedures such as double sided tape, resting on a flat surface provided the vibration level is less than a given amount. But if it is worth going to the expense of the monitoring equipment and manpower, surely it is worth a little extra effort to ensure the primary sensor is coupled to the ground effectively. The primary sensor must move with the ground and measure this movement; so if the primary sensor is allowed to move without respect to the ground (ie poor coupling to the ground) then a false record of the physical event will be measured. This scenario can easily be a practical reality if the primary sensor coupling method to the ground is not effective. In this study a number of mounting methods were fabricated and connected to similar data monitors and a series of ænormalÆ production blasts were used as the vibration source. These mounting devices were measured against an in-house procedure (the æstandardÆ) and the relative merits compared. A laboratory investigation was also carried out to look at the physical parameters of the æsoil and their effect on vibration attenuation of the in-house standard method.

Jan 1, 1999

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012