Search Documents

By C. Haberfield, J. Szymakowski

Recent studies by the authors into the behaviour of jointed rock masses using direct shear testing have confirmed that joint spacing has a significant effect on rock mass strength. The rock mass failure envelopes assessed from these tests have been compared to failure envelopes obtained using the Hoek-Brown GSI criterion. Good agreement between measured and estimated GSI strength envelopes where obtained when joint spacing was considered in the assessment of GSI. Les études récentes conduites par les auteurs sur le comportement des joints rocheux employant l'essai direct de cisaillement ont confirmé que l'espacement a un effet significatif sur la force de la masse rocheuse. Les enveloppes de ruptures obtenues pour ces essais ont été comparées à l'enveloppe de rupture obtenue en utilisant le critère GSI Hoek-Brown. Une bonne corrélation a été constatée entre les enveloppes obtenues expérimentalement et les enveloppes calculées par la méthode GSI quand l'espacement des joints a été pris en considération dans l'évaluation de GSI. Kuerzliche Untersuchungen der Autoren betreffs Reaktionen von gebrochenen Felsmassen zu direkter Scherkraft, bestaetigen, dass die Abstaende von Rissen einen deutlichen Einfluss auf den Widerstand der Felsmassen hat. Die Bruchbereiche der Felsmassen die von diesen Untersuchungen entwickelt wurden, wurden verglichen mit den Bruchbereichen, die man mit der Anwendund der Hoek-Brown GSI Formulierung erhaelt. Eine gute Uebereinstimmung zwischen gemessenen und errechneten GSI Festigkeitsbereichen wurde erzielt, wenn der Abstand der Risse in der Berechnung der GSI in Betracht gezogen wurde.

Jan 1, 2003

By S. H. Ash

For several years considerable activity has been devoted to economic and social factors affecting California metal-mining operations as they relate to accidents and their cost. The reason for this intense interest is that accidents cost this industry annually over $1100,000 in industrial insurance premiums for mines insured by insurance carriers only; during 1924-32, inclusive, they amounted to $3,616,9115. There are several reasons for this high cost, the most important of w rich are the consistently .high frequency and severity rates of injuries occurring in the industry. Coordination of effort, appreciation of a mutual problem, and widespread education are essential if accidents and their cost are to be reduced.

Jan 1, 1935

By Roy E. Peterson

The Bureau of Mines conducted bench-scale research to evaluate materials which showed potential as low-cost reductants for use in the ironmaking industry. These materials were lignite, subbituminous coal, coal char, tree trimmings, refuse--derived paperboard, used crankcase oil, and peat. To compare their effectiveness, the materials were tested in the reduction roasting of nonmagnetic taconite and, except for oil and peat, in the reduction of iron oxide pellets to metallized pellets. Reduction was conducted in a 18-cm-diameter, rotary drum, which was externally heated in an electric furnace. Over 92 pct of the iron was magnetically recovered from a nonmagnetic taconite after roasting with any of the reductants, but greater quantities of reductant were required to achieve this when the waste materials were used. The fossil fuels were also more effective for metallizing pellets, although metallizations above 90 pct were also obtained with tree trimmings and refuse paperboard. However, refuse paperboard had to be frequently recharged to the furnace because it depleted rapidly.

Jan 1, 1983

By X. Yuan

"The processing behaviours of ores such as their liberation characteristics in comminution and their response in separation processes are affected by their mineralogical characteristics. Key ore characteristics which are relevant to processing, such as mineral proportions, mineral grain size, grain shape and mineral associations are routinely measured at the micro-scale in polished section using optical microscopes and SEM-based automated mineralogy systems. The application of X-ray micro-tomography to mineral processing provides the means to quantify these important micro-textural characteristics in three dimensions, removing the stereological issues encountered when measuring volumetric information in two-dimensional polished sections. In this paper we present several examples of ore textures to illustrate where X-ray micro-tomography can be applied successfully to obtain quantitative measures of ore characteristics which are useful in a variety of process modelling applications.INTRODUCTION X-ray tomography has been used as a tool in medicine for some years and is being applied in a wider range of fields including geology, palaeontology and mineralogy. In this paper we present some applications of X-ray tomography in mineral processing applications being developed at JKMRC. The availability of SEM-based automated mineralogy systems such as MLA and QEMSCAN has seen the increased use of quantitative mineralogical data measured in two dimensions in the design, operation and simulation of mineral processing plants. When the ore is amenable to measurement by X-ray tomography this technique can provide quantitative data for characteristics such as mineral grain size, shape, mineral associations and liberation in three-dimensions. The advantage of measuring these characteristics in three-dimensions is that the stereological issues which bias measurements made on polished sections are removed. X-ray tomography also quantifies the location of mineral grains relative to one another in space - a useful descriptor of ore texture. Like many measurement techniques X-ray tomography has advantages and disadvantages when compared to other techniques. One limitation is that the ability of the X-ray tomography system to discriminate between minerals is a function of the X-ray attenuation of those minerals. While the X-ray attenuation of many common minerals is sufficiently different for X-ray tomography to distinguish between them, there are some where the overlap in X-ray attenuation makes discrimination on the basis of this characteristic alone impossible. An example of this would be chalcopyrite and magnetite. However where the ore mineralogy is suitable to apply X-ray tomography, the technique provides some exciting opportunities to explore the relationship between texture and ore processability."

Jan 1, 2012

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, K. Fountain

"A comparison of data from INPUT, GEOTEM, and MEGATEM airborne electromagnetic (AEM) systems over the Aldermac deposit, Québec, Canada, was undertaken to evaluate the relative ef¬ficiency of these systems for the detection of small, deep conductors. The Aldermac orebody was mined between 1933 and 1934 to a depth of 200 m. A deeper mineralized zone was discovered in 1987. The MEGATEMII system was used to acquire 90- and 30-Hz data over the deposit in 2003 as part of a research project. These MEGATEMII data were compared with data acquired by other AEM systems (GEOTEM and INPUT), and the results show that the MEGATEMII response is ten times larger than the other sys¬tems. For the dB/dt response, 30 Hz gives a better signal-to-noise ratio, whereas 90 Hz has a better signal-to-noise ratio on the B-field.The data were evaluated by numerical modeling. The deposit was best represented by a complex mod¬el, comprising two weakly conductive bodies to approximate the alteration halo, two deeper prisms repre¬senting known orebodies, and three bodies ranging in thickness from 3 to 6 m and in resistivity from 12 to 20 ohm·m, representing the chargeable overburden. This implies that the MEGATEMII system is able to see a small conductive body at more than 200 m depth in an area where the response is contaminated by conductive overburden."

Jan 1, 2009

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM containing suphide concentrates is reviewed, along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors, which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistively, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte are discussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis, and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace, with reference too perating current, power input, furnace dimensions and electrode size, are based on considerations derived mainly from slag properties such as its resistively, viscosity and liquidus temperature.

Jan 1, 2004

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By Stephen T. Young

The construction of Phase 2 of Hong Kong Station, its retail podium and International Finance Centre Two, the tallest building in Hong Kong, will be completed in the middle of 2003. This paper describes the design and construction of the slurry wall for the Station (both Phase 1 and Phase 2) and the two commercial buildings at the Station. The slurry wall is used as the permanent earth support wall for the station box and the excavation depth ranges from 70 feet to 120 feet. Top-down construction technique was adopted to support the excavation of the station, while circular cofferdams relying on hoop stiffness were constructed to support the basement excavation of the two towers. The designed behavior of the slurry wall is also compared to the as built behavior.

Jan 1, 2003

By W. F. Watts

This report describes the Mine Inspection Data Analysis System (MIDAS) developed by the Bureau of Mines to analyze the records of industrial hygiene samples collected by the Mine Safety and Health Administration (MSHA) in metal and nonmetal mines. MIDAS is the first system capable of sorting, editing, analyzing, and reporting these data. It is also the first system designed to be used by a number of Government agencies. At present the system contains 225,000 personal and area samples for 61 contaminants in 45 industries. The records date from 1974 to early 1980, and MSHA plans to provide yearly updates to the system. This report presents preliminary analyses of dust exposures and discusses the potential uses and limitations of these data. Analysis of the dust data for 1978 and 1979 showed that bagging had the highest percentage of dust overexposure. Morn than 40 pct of the 1,536 respirable quartz dust, total nuisance dust, and total silica dust samples exceeded the MSHA exposure limit. Other dusty occupations are ranked according to their percentage of overexposure.

Jan 1, 1981

By Joseph A. Vanous

The inductive communication system was developed under this contract for use in the hoist of deep mines. This program was a four phase program with experimental dual frequency equipment resulting from Phase I, emergency single frequency equipment developed under Phase II, and equipment documentation required under Phase III. An additional emergency system was provided under Phase IV.

Jan 1, 1976

By P. Mousset-Jones, G. Danko

Variations of the temperature and steam/moisture content of the air with distance and time are modelled for a single airway. The input for the simulation is an air temperature that varies with time, together with the moisture/steam content that results, for example, from a fire with a given distribution of heat and of fume concentrations at the beginning of the airway. The transport of heat and moisture to the surface of the wallrock is assumed to be simultaneous. Such multiphase convection may result in evaporation from the moist wall close to the fire and recondensation downstream. The modelling of this non-linear effect is a unique feature of the new simulation. A new analytical solution is used to calculate the conduction of transient heat within the rock mantle, which, in the event of a fire, is typically a short-term process. This allows for an arbitrary variation of surface temperature with time - unlike that permitted by the age function solution, which is limited to stepped temperature changes. An iterative numerical scheme that has recently been developed to simulate mine climate is used to calculate the coupled transient heat conduction and multiphase surface heat transport in successive length increments along the airway. To demonstrate the simulation procedure a numerical example is presented in which a fire with a given distribution of heat and fume concentrations with time is located at the beginning of an airway

May 1, 1991

By C. D. Thompson

Pile load test programs were carried out in 1984 and 1985 at Stelco's and Dofasco's Steel Making Plants in the Hamilton Bayfront area. 323.9 mm outside diameter by 9.5 mm wall thickness Grade 3 steel closed-end pipe piles were driven to practical refusal at depths of 21 to 30 m in very dense silt till with Delmag D30 open-end diesel hammers. Ultimate bearing capacities of up to 5330 kN were proved by dynamic monitoring and static load tests. Allowable bearing capacities of 1780 kN were achievable on production piles without undue difficulty. It was found that the impact stress at the top of the pile was controlled by the yield strength of the steel rather than a useable upper limit based on the modulus of elasticity. A bearing to impact stress ratio of 1.2 at practical refusal was observed to be reasonable but conservative at this site, and is felt to be generally applicable for piles driven to practical refusal elsewhere. Dynamic monitoring during production pile driving was able to show that apparent relaxation was caused by pre-ignition of the hammer when visual observations indicated that pile driving was proceeding satisfactorily.

Jan 1, 1987

By J. A. Finch, J. Vergouw

"Flotation selectivity becomes progressively more difficult to achieve with decreasing particle size. One of the possible problems is agglomeration, i.e. particles clustering together. One mechanism derives from the surface charge all particles develop in water. Agglomeration driven by surface charge is known as coagulation. One form is coagulation between particles of two different minerals of opposite charge. Another is coagulation between particles of the same mineral when conditions are such that the charge approaches zero.The paper describes the method of measuring charge and a new automated settling technique for measuring agglomeration. The phenomena are illustrated with galena and pyrite. Methods of assessing the importance of agglomeration in the plant environment are still to be developed.IntroductionFine particles can agglomerate (i.e. adhere to each other) under certain conditions. This is counter-productive for any physical separation process, including flotation. One cause of agglomeration derives from the surface charge that all particles develop in water. Agglomeration due to surface charge effects is referred to as coagulation. There are two forms of coagulation. If the surface charge is brought to near zero then the force of repulsion is lost and particles coagulate. This usually applies to particles of one mineral type and the technical tenn is homocoagulation. On the other hand, if two particles have opposite charge there is an attractive force. Since the particles in this case are usually different minerals this is known as heterocoagulation.Both types of coagulation can cause minerals to be misplaced. In the case of heterocoagulation this is fairly obvious. One example that may be familiar is slime coating (fines of one mineral coating larger particles of another) But even homocoagulation can be a problem an agglomerate of the same mineral particles can entrap particles of another mineral."

Jan 1, 1997

By R. Boom, L. Holappa

In the present paper, microstructure changes of solid-state reduction of industrial chromite pellets and lumpy ore were investigated with SEM/EPMA. To simulate the reactions in the packed bed zone of the Submerged Arc Furnace (SAF), carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at 1500 °C. Scanning electron microscopy was used to observe and analyse the structure and composition changes of the chromite samples. It was found that reduction of lumpy ore generally took place slower than that of pellet. In all samples, chromite reduction proceeded faster in the outer part of the sample than in the centre part. The reaction mechanism is discussed on the basis of experimental results and earlier investigations. The possibilities to optimize the FeCr production process are also discussed.

Jan 1, 2007

By A. L. Murray

First -aid training as an adjunct to safety is receiving more wide spread recognition in the industries every year . Moreover , the adoption of a program for giving firstaid training to practically all employees at a mine or plant is based upon the experience gained and good results obtained from standard first -aid instruction during the past two decades . In the near future industries that desire to maintain a low accident rate , to decrease compensation costs , to reduce lost time , and to build up an efficient , loyal working force , will recognize that training in first aid is one way of attaining these results with little expenditure of time and effort . Progressive organizations will require every man from the superintendent down to take first - aid training and not , as heretofore , only a small percentage of the working force . When employees learn that first - aid training can be applied not only at their daily tasks but in their homes and on tthhee highways ,, they will welcome the opportunity of learning how to care for injuries and perhaps save lives . In a limited way first - aid instruction was given to miners as early as 1899 . Later , in 1904 , a few of the companies in the Pennsylvania anthracite district inaugurated the distribution of first - aid packets to their employees and instructed them in the use of the contents . It remained , however , for a branch of the United States Government to grasp the real significance of widespread first - aid training as an effective means of saving life and minimizing suffering from the large number of accidents among workers in the mineral industries . The United States , owing to its vast resources , both natural and human , for

Jan 1, 1930

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.' Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,' and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

By Carl D. Ealy

Work is being done to web enable the FHWA Deep foundation Load Test Database. Originally designed to function in the client server environment via modem, access to the database both for data maintenance and user queries has been upgraded to take advantage of the Internet and current and future information technology innovations. The DFLTD will be part of an Automated Geotechnical Information and Design Aid System, the object of which is to assist those involved with managing and maintaining our nation's highway infrastructure. The system will also meet the needs of university and other research institutions for a statistically meaningful source of high quality data for the development and verification of improved analysis methods, in-situ testing methods, etc.

Jan 1, 2002

By J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

"The Niobec concentrator rejects up to /5% of the Nb as slimes (-10u.m). The recovery of Nb from these slimes by column flotation is being studied. An essential condition for selective flotation is slimes dispersion. A particle size analyzer, the Sedigraph 5000D, was used to monitor dispersion in plant waters with combinations of organic and inorganic dispersants and flotation reagents. Flotation reagents were particularly detrimental to dispersion with sodium silicate. The best dispersion conditions were selected for column flotation tests. These tests revealed that reagent combination had a pronounced effect on froth stability. Careful frother selection achieved good froth stability under conditions of good dispersion. Plant water increased the required dispersant concentration causing mineral depression.IntroductionSlimes (-10 u.m) rejected at Niobec contain up to 15070 of the over-all Nb content . Recovery of Nb from these slimes would significantly increase over-all recovery. A suggested recovery route involves two phases: (1) carbonate flotation (to remove most of the carbonates) depressing silicates and pyrochlore (as currently done at Niobec); and (2) selective (direct) pyrochlore flotation from the silicates. Phase 2 has been addressed and several routes to achieve selective flotation are available. Phase I was attempted with the selective reagent scheme used at Niobec but a considerable amount of pyrochlore floated with the carbonates due to poor slimes dispersion."

Jan 1, 1987

By J. E. Rourke, O&apos

A wide variety of techniques and equipment are available for coring soft or poorly consolidated geological material. This report presents a comprehensive literature review and evaluation of these techniques and equipment. A potential user will find guidelines in this report to assist him in selecting sampling equipment. A bar chart shows what samplers have been used under what geological conditions, and gives the specific literature references. Two matrices rate the present techniques and equipment with respect to reported success for sampling specific materials, and with respect to several performance characteristics including complexity of use and core quality. These matrices are supplemented with tables of typical sampling equipment. and program costs. Near-term future developments are seen primarily in improved training of drillers, and in instrumenting the drilling operation to provide objective data on drilling characteristics. An extensive annotated bibliography, a catalogue of equipment suppliers including specifications and cost ranges, and a list of manufacturers and distributors are appended to the report.

Jan 1, 1978

By Russell Griffin

The current state of the art of fire and smoke detection technology is reviewed from the standpoint of suitability for use in under- ground metal and nonmetal mines. Detection modes, fire signatures, and environmental considerations are included. Preliminary results of long- term, in-mine tests are presented.