Search Documents

By Paul J. O'brien, George N. Neary

"The base metal mine at Buchans, Newfoundland, has been producing since 1928. For many years, mill tailings were disposed of by dumping into a nearby natural watercourse via which they were transported to Red Indian Lake and deposited. In 1965, environmental concerns prompted the establishment of settling ponds near the mine site. Effluents fed to these ponds included slimes washed from mine backfill sand and waste water pumped from underground as well as mill tailings. Dusting around the perimeter of the ponds was first observed around 1970and within a couple ofyears reached serious proportions. A program to alleviate the condition by developing a vegetative cover over the tailings was commenced in 1974. The work was successfully carried out and demonstrated that the large area of waste could sustain a permanent cover of grasses.This paper outlines the experimental work done at Buchans as well as the procedures followed and the problems encountered in carrying out full-scale revegetation."

Jan 1, 1981

The mineralogy of the rocks now observed in the Nairne pyrite deposit developed under conditions of internally-controlled sulphur activity during amphibolite facies metamorphism. In the sulphide-deficient metasediments the activity of sulphur was low, and pyrrhotite developed with iron-bearing silicate minerals. At higher sulphur activity, in the sulphide-rich meta-sediments, pyrite formed in addition to pyrrhotite, and the associated silicate minerals are iron-deficient.

Jan 1, 1969

By H. Maleki

As mining continues toward deeper reserves in thick western US coal fields, the control of mining induced-seismicity has become a priority in many operations in Utah, Colorado, and Wyoming. Gradual floor heave, common in many coal mines, has historically not been a safety issue. However recent occurrences of sudden floor heave accompanied with seismicity in a few deep mines have fueled this investigation. The focus is to identify and study the mechanisms resulting in sudden heaving of the mine floor in western U.S. deep coal mines through analytical calculations and back analyses of an actual event in a cooperative mine. Based on review of available data in three mines, underground observations and back analyses of an actual event, the authors have identified the following contributing factors (1) presence of stiff stratigraphic units and thick seams mined at depths exceeding 1000-ft (2) presence of geological discontinuities reducing the in-situ strength of the coal with calculated factor of safety near 1 for the mine floor (3) mining approaching areas of higher than normal stress gradient associated with previous mining or structural anomalies or surface topographic highs and (4) an additional source of energy triggering sudden failure such as periodic caving or slip along geological discontinuities. Preliminary examination of seismic data for the actual event in the cooperative mine and underground observations excluded fault slip at the mining horizon as the triggering mechanism but highlighted the significance of weak, anisotropic strata conditions near the intersection of two faults.

Jan 1, 2009

Scattered north and south along a 161-km (100-mile) stretch of Interstate 80, Newmont Min¬ing Corp. owns four active mining properties in Nevada?s northern high desert ? Carlin Trend Operations, Midas, Twin Creeks and Phoenix. Among the four, there are nine openpits, five underground mines and 14 processing facilities. While gold is the predominant ore, silver and copper are also produced. And in a move to hold down energy costs, Newmont built and owns the 200-MW (net), coal-fired TS power plant. This plant provides about 65 percent of the power used for Newmont?s own operations, while the rest is sold to NV Energy, which services Nevada and northeastern California. Bringing the Phoenix Mine ? Newmont?s newest in Nevada ? on-line presented many developmental and operational challenges. Located about 19 km (12 miles) southwest of the town of Battle Mountain, the general area had been home to prospectors and other mining companies since the 1860s. But any profitability in developing the lower grade gold, copper and silver deposit at Phoenix proved elusive, with Battle Mountain Gold being the last company to make an attempt. When Newmont acquired Battle Mountain Gold and its Phoenix reserves in 2001, the lower grade of ore was not a deterrent. Newmont found Nevada-wide cost savings synergies for maximizing profit during the depressed gold market of the late 1990s. The new property was aptly renamed the Phoenix Mine, a nod to its rising from the ashes of the dreams and efforts of previous mine owners.

Jan 2, 2010

By P. Schmieder

"The close vicinity of mining companies to other sites that are used for commercial and residential purposes or to areas under conservation as well as the fact that the people become more and more sensitive to emissions have led to a negative attitude towards mining operations in the neighborhood. It is above all the use of drilling and blasting techniques that give rise to objections, in the course of which demands for more environmentally-friendly production methods have been voiced. It is in this context that production methods without the use of explosives are considered as an option. After all, the use of such production methods is the only alternative for some quarry operators. The question is what are the true benefits of these techniques and what is the relation between a possible improvement of the environmental effects on the one hand and the technological potential as well as the costs on the other. It is intended to assess the mining techniques for solid rock in their entirety. This paper will therefore look at the aspects for assessing mining techniques in the context of their environmental impact and the costs."

Jan 1, 2005

By Javier Rodriguez

Adaptive re-use of existing structures in urban environments has become very common due to lack of available space in our cities and requirements for increased structural capacity. Often, it involves retrofitting existing foundations to support increased loading. In such cases, Engineers face the need to review existing deep or shallow foundations for their true load carrying capacities in order to determine the required magnitude of retrofit work, if any. To accomplish this, the engineer must track down and cull through the existing construction documentation to determine what was actually constructed, complete an investigation to confirm these conclusions, possibly sample the foundation elements for strength properties, and on occasions complete non destructive or full scale load testing of indicator elements. This paper describes the typical procedure followed by the authors for design of retrofit schemes for existing buildings in the Washington DC metropolitan area. Three case histories are presented that illustrate various issues encountered during design.

Jan 1, 2006

By Martin Herrenknecht, Karin Bäppler

The last five years have seen a remarkable increase in tunnelling projects in both soft ground and hard rock applications. Part of the increase is a result of recent Research & Development efforts to improve Tunnel Boring Machine (TBM) adaptability, capability and reliability. This paper will review the latest innovations in the TBM industry and explain in detail the results of these innovations followed by a forecast where the technology will take the tunnelling industry in the future.

Jan 1, 2005

By C. J. H. Steenkamp

Theoretically, the main driver behind a mining operations? sourcing decision should differ from company to company, and within a company from project to project, but in reality it often relates to cost. Research confirms that there are a number of factors, including cost, to consider when choosing between in-house and outsourced mining. While the literature is rife with factors to consider, little information exists on how to apply these in practice and the relative importance of the different factors to be considered. A study was conducted to determine whether mining is truly a core competency for a mid-tier commodity specialist mining company. Furthermore, a decision-making framework for mining operations sourcing was developed, and the critical success factors that should be adhered to if outsourced mining is chosen were determined. The research showed that owner mining is not a core competency for the mining company investigated. A decision-making framework was developed using the order winner/order qualifier structure, which can be used to facilitate the mining sourcing decision. The most important tools at the disposal of a mine owner?s team to manage a contractor miner are the social and output control mechanisms, according to the critical success factors study.

Jan 1, 2014

Resolution Copper Mine is planned to be a 2000 m deep panel cave mine with virgin rock temperatures above 80°C in rock with a high crystalline silica content. The planned run-of-mine production rate is 120 kt/day. The project is in prefeasibility evaluation. This paper discusses features of the ventilation system design, which include multiple ventilation shafts with total flow of about 3000 m³/s and both surface and underground refrigeration systems with more than 140 MW total capacity. This will be a very challenging mine to ventilate, but this work has demonstrated that it will be technically achievable with the application of existing technology.

Jan 1, 2014

By G. A. Bezuidenhout, J. P. T. Kapusta, D. K. Chibwe

"Peirce-Smith converters (PSCs) are extensively used in the copper, nickel, and platinum group metals industries. The typical converting operation involves lateral purging of air into molten matte through a bank of tuyeres. This blowing operation occurs at low pressure from the blowers, resulting in a bubbling regime that is considered inefficient from both a process and an energy utilization perspective. Inherent drawbacks also include recurrent tuyere blockage, tuyere punching, and low oxygen efficiency.Western Platinum embarked on a full-scale industrial evaluation of generating a jetting regime by using sonic injection. Prior to industrialscale tests, a numerical assessment to ascertain the feasibility of implementing sonic injection into a PSC was conducted. The work included flow characterization at high-pressure injection achieving sonic velocity at the tuyere exit. The 2D and 3D simulations of the three-phase system were carried out using the volume of fluid method together with the RKE turbulence model to account for the multiphase and turbulent nature of the flow.This paper discusses the key findings in understanding plume extension, velocity distribution, shear wall stress analysis, and phase distribution characteristics in the system. Plant trials are also discussed with reference to the commercial aspects of a full-scale implementation of sonic injection in the smelter."

Jan 1, 2015

With the dawning of a new century came the beginning of a new era in the coal industry. Instead of the traditional practice of only buying and selling produced coal in the United States, a coal futures market was established. The New York Mercantile Exchange began trading coal futures in July 2001. But, even in this new era, many of the old is-sues that have beset the coal industry still remain, as was evident in2001. Coal production increased to are cord level during 2001, according to preliminary data from the US Energy Information Administration(EIA). Production in 2001 rose by4% to 1.01 Gt (1.12 billion st), compared with 2000 (Table 1). This barely surpassed the previous record level of 1 Gt (1.11 billion st)set in 1998. Coal consumption remained unchanged. The additional production was used to replenish the depleted stockpiles that had resulted after two years of declining coal production and increasing coal consumption.

Jan 1, 2002

By J A. Rabe, PAP Fouche, K O?Neill

Two of the most important issues mines have to deal with are tracking the ore mined from pit to plant and to test the efficiency of beneficiation equipment. Kumba Resources and Saco Systems are working together at moment to develop a RFID tracer system to help address these issues. This paper will focus on the tracking of ore from pit to plant. The main advantages for ore tracking is to ensure plant feed blending and dilution according to plan. The RFID tracer system works on the basis of a tracer that physically simulates the ore properties and radio frequency technology that facilitates communication with the tracer and allowing information to be stored on the tracer. This paper tends to indicate the progress on the application of RFID tracer technology in the minerals processing environment as tested at Kumba Resources so far. It is concluded that the system has great potential, but some important problems remain

Jan 1, 2005

By D. M. May

"Cut-and-fill mining is a stoping method that has been widely utilized in the mining industry over the past forty years. It took preference over shrinkage methods at Levack in the early 1930sbecause of its safety aspects; i.e., prompt support of the stope sidewalls, good working floors and better accessibility to support poor back areas. In addition, higher recoveries of ore were possible because of the flexibility of the method in that silling could take place easily at any horizon; low-grade ore could be sorted and left in the stope as fill and certain zones of rock could be left unmined. With modern techniques, a steady production rate can be established, as filling and mining can be carried out stimultaneously.AIthough there are numerous variations of cut-and-fill mining throughout the world, this paper reviews the original type of mining, with modifications and improvements through the years to present modern practices, with the Levack West operation appearing to be the most productive at this time. Stoping efficiencies have also increased substantially from the original 10 tons per manshift to the present 55 tons per manshift.The paper also outlines the many improvements that have been made with respect to mucking and ground support operations; from hand mucking in a single stope to the use of frontend loaders and haulage trucks in fully accessible stope complexes; and from timber props to roof bolts of various types. Although present methods are extremely satisfactory, experimentation is continually being conducted to improve safety and productivity for future mining.IntroductionThe major mining operations of the Ontario Division of Inco Limited are located in the Sudbury Basin (Fig. 1). Around the rim of this geological formation and within 30 miles of the City of Sudbury are nine producing mines and one ' open pit operated by the company .Ore production currently approximates 11.5 million tons per annum from underground and open-pit operations. Underground mining methods include sub-level caving, shrinkage, cut and fill, undercut and fill, blasthole and vertical retreat. The Levack Complex, the main plant of which is the central Levack Mine, produces 11,000 tons per day.The first prospecting in the Levack area, in 1887, was conducted by James Stobie, who examined rock cuts along the route of the Canadian Pacific Railway to the northwest of Sudbury. However, it wasn't until 1913 that operations commenced at Levack under the Mond Nickel Company."

Jan 1, 1981

By X. Goso

Laboratory-scale tests were conducted at Mintek for the production of titanium powder from particulate Kroll sponge by the hydrogenation-dehydrogenation (HDH) process. The aim of this work was to produce titanium powder for powder metallurgical consolidations. The work involved the production of titanium powder at optimized conditions, which included hydrogenation in a horizontal tube furnace at 600°C for 2 hours, milling using planetary and roller mills, and dehydrogenation in a vacuumed retort fitted in a muffle furnace running at 700°C for 36 hours. The titanium powder produced in this project matched the elemental specifications of commercially available titanium powder, except for high carbon content. Nevertheless, the powder has been tested further in mechanical alloying and has been found suitable for the production of powder metallurgical compacts. Keywords Powder metallurgy, titanium components, HDH process, ball milling.

Jan 1, 2011

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By David Bendersky

This report covers the activities of a feasibility study of fiber optics technology fur use in mines. The objective of the study was to evaluate, both technically and cost-wise, the possible use of fiber optic technology for underground mine communication and monitoring systems. The first phase of the study was devoted to the collection of information on the present underground mine communication systems and monitoring techniques, and the status of applicable fiber optic technology. In the second ph se of the study, a communication and monitoring system for a hypothetical underground coal mine was designed and the costs estimated. The significant findings and conclusions are presented.

Jan 1, 1982

By John R. Zelonka

Models made by encasing strain-gage networks in epoxy are described and evaluated. With this technique relatively complex models can be constructed in which any number of gages can be located and alined precisely. Although the gages are an integral part of the model matrix, they create no important mechanical or thermal stresses. Model construction techniques and experimental data proved reproducible and reliable. In addition, the sGlution obtained with these models to the problem of the state of stress around a circular hole in a plate subject to a plane stress condition was in agreement with theoretical, photoelastic, and finite-element solutions.

Jan 1, 1970

The effect of rare earth element Y (0-2.0at.%) on the microstructure of TiAl alloys at the as cast and rapidly solidified conditions has been investigated. The results show that the addition of Y greatly refined the microstructure of TiAl alloys at both conditions. The refinement is more significantly with higher Y content. The refinement of Y in the cast alloys is attributed to that the strip-shaped Y-rich phase locating on the grain boundaries impedes the grain growth during solidification. In the rapidly solidified alloys, Y-rich phase dispersing uniformly as spherical particles in the matrix acts as heterogeneous nucleation sites which increases the nucleation rate of ??phase during the ????phase transformation, and produces a refined initial microstructure during solidification. Higher cooling rate restricts the grain growth during subsequent cooling.

Jan 1, 2010

By G. Thodos, R. B. Grieves

A method has been developed for the accurate calculation of the cricondentberm and cricondenbar temperatures of multicomponent hydrocarbon mixtures of known composition. The mixtures may contain any number of components including paraffins and isoparaffins, olefins, acetylenes, naphthenes and aromatics. This approach is based upon the mole fraction of the low-boiling component in the mixture and graphically presents the ratios of the cricondentherm and cricondenbar temperatures to the pseudocritical temperature as {unctions of a boiling-point parameter. The only requirements are the critical temperature, normal boiling point and the approximate vapor pressure behavior of each component. For mixtures of more than two constituents a stepwise calculation procedure is necessary where the pseudocritical temperature is based upon the critical temperature of the pure low-boiling component and upon the actual cricondentherm or cricondenbar temperature of the mixture of all the remaining higher-boiling components. From an analysis of 22 binary systems (123 compositionsl, the average deviation of calculated cricondentherm temperatures from reported values is 0.87 per cent, based on degrees Rankine; and for 10 multicomponent mixtures containing from three to six components, the average deviation is 0.98 per cent. From an analysis of 18 binary systems (104 compositions) the average deviation of calculated cricondenbar temperatures from reported values is 0. 79 per cent; and for 15 multicomponent mixtures, 1.47 per cent. Equations, derived from the graphical relationships, are presented which enable rapid calculations for both binary and multicomponent systems. INTRODUCTION With the increasing tendency towards the use of high pressure processes, the need for an accurate method of calculation of the properties of a multicomponent hydrocarbon mixture in the critical region is becoming more essential. Critical region phase relations are also significant in gas condensate reservoirs, for which a knowledge of the fluid phase boundaries and regions of retrograde condensation make it possible to evaluate optimum operating conditions. The possibility of liquefaction in the underground structure may be established, and information on the feasibility of the use of repressurizing may be determined. A typical phase diagram for a multicomponent hydrocarbon mixture is presented as Fig. 1. This figure also shows the regions of retrograde behavior encountered by following lines AB and AC. If accurate methods of calculating the temperatures and pressures at the critical, cricondentherm (maximum temperature) and cricondenbar (maximum pressure) points of multicomponent hydrocarbon mixtures of known composition were available, it would be possible to estimate closely the entire phase diagram of any mixture. Several methods have been presented in the literature for the estimation of the critical temperatures and pressures of multicomponent mixtures containing all types of hydrocarbons and including the fixed gases.4-8,21 Considering the cricondentherm and cricondenbar points, the work is more limited. Etter and Kay5 have developed rather complex equations for

By C. M. F. Vieira

This work has as its objective to characterize ceramic bodies for vitrified tiles elaborated with the mixture of nepheline-syenite flux and kaolinitic clay. Formulations were prepared with 0, 30 and 50 wt.% of nepheline-syenite incorporated in a kaolinitic clay. To determine the physical and mechanical properties such as dry bulk density, linear shrinkage, water absorption and flexural rupture strength, specimens were prepared by 30 MPa uniaxial pressure-molding and then fired in a laboratory furnace at 1150oC. The microstructure of the fired ceramics was evaluated by scanning electron microscopy. The results indicated that the nepheline-syenite improved the evaluated properties of the clay and attended the specifications of vitrified ceramic tiles.

Jan 1, 2010