Search Documents

By K. J. Oliver, A. G. Meyers, S. P. Hunt

Deformation Rate Analysis (DRA) and porosimetry have been used to demonstrate the “stress memory” effect in rock and to estimate the vertical in-situ stress in samples of fine-coarse grained sandstone and carbonaceous mudstone. The results of this study indicate that the stresses predicted using both methods are similar to those determined from depth and density of the overburden rocks. The results confirmed that DRA was still applicable even when the core had been sampled 18 months prior to testing. Additionally, the DRA results were modelled using the software PFC2D. A uniaxial test was modelled using the same rock parameters as those observed for the actual core samples. This numerical technique can be used as an aid for DRA results analysis, and can also be used to predict the minimum stress level at which the DRA technique is applicable. The results confirm that any rock mechanics laboratory having standard test equipment could apply the DRA method combined with standard UCS testwork to determine the in-situ stress. Mit der Analyse der Deformationsrate (DRA) und der Anwendung der Porosimetrie wird der Spannungsgedaechtnisseffekts (Stress Memory Effect) im Fels demonstriert, und es werden Abschaetzungen fuer die vertikale in-situ Spannung einer Probe aus mittelgrobem Sandstein und carbonierten Lehmstein getroffen. Die Ergebnisse dieser Untersuchung zeigen, dass die mit Hilfe dieser beiden Methoden ermittelten Spannungen sind vergleichbar. Die Ergebnisse bestaetigen, dass DRA noch anwendbar ist, wenn die Proben schon 18 Monate vor Untersuchungsbeginn gesammelt worden sind. Darueber hinaus wurden die DRA Ergebnisse mit Hilfe des Sofwarepakets PFC modelliert. Ein einaxialer Test wurde mit genau die gleichen Felsparametern, die fuer die eigentliche Probe gelten, modelliert. Diese numerische Methode kann sowohl als eine Unterstuetzung fuer DRA Ergebnisanalyse als auch zur Ermittlung der minimalen Spannung, bei dem die DRA Methode noch anwendbar ist, herangezogen werden. Die Ergebnisse bestaetigen, dass jedes Felsmechaniklabor, das mit den ueblichen Testgeraeten ausgestattet ist, die DRA Methode in Kombination mit dem Standard UCS Testarbeit zur Bestimmung der in-situ Spannungen anwenden kann. L'Analyse du Taux de la difformité (DRA) et les porosimetry ont été utilisés démontrer le " effet de la mémoire " du stress dans roc et estimer le stress dans - situ vertical dans échantillons de grès du grained fin grossier et mudstone carbonifère. Les résultats de cette étude indiquent que les insistances ont prédit utiliser les deux methods est semblable à ceux déterminés de profondeur et densité du surchargez des rocs. Les résultats ont confirmé ce DRA était encore même applicable quand le coeur avait été goûté 18 mois avant tester. En outre, les résultats DRA étaient des modelled qui utilisent le logiciel PFC2D. Une épreuve de l'uniaxial était modelled qui utilise les mêmes paramètres du roc comme ceux observé pour les réels échantillons du coeur. Cette technique numérique peut être utilisée comme une aide pour DRA résulte analyse, et peut aussi être utilisé pour prédire le niveau du stress minimum à que la technique DRA est applicable. Les résultats confirment que tout laboratoire des mécaniques du roc qui a le matériel de l'épreuve standard pourrait appliquer la méthode DRA combinée avec testwork UCS standard pour déterminer le stress dans - situ.

Jan 1, 2003

By F. Keller, E. H. Dix, L. A. Willey

The consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathewsi and by Tammann.2 Canlpbell and mathews described principally the beginning of solidification. They found the curve of beginning of solidification rising gradually from the melting point of pure alunlinum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AISb. The curve then drops to the melting point of pure antimony. Tamrriarln explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AISb. The space lattice of the compound AISb, according to Owen and Preaton,³ is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony. The Present Investigation It has been the purpose of this investigation to determine the solid solubility of antimony in aluminum and also to investigate the eutectic temperature and concentration. The experimental work has been carried out in a manner similar to that described in a previous paper4 from this laboratory.

Jan 1, 1931

By T. M. Williams, P. M. Green

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The sediment geochemistry of streams draining Southern Uplands and Lake District turbidites was compared with lithogeochemical data for the source greywackes, using stratigraphically defined catchments. Several systematic trends in element abundance variation between source and stream sediment can probably be applied more widely to interpretation of drainage geochemistry. Pb and Zr increase markedly from source rock to sediment, by adsorption on clay and zircon grain concentration. Variation of feldspar-related elements Rb, Sr, K and Ba appears to be controlled by source grain size and compositional maturity. Ni shows surprisingly little change and Fe and Co are only slightly raised. Cr is particularly useful, with variations superimposed in anomalously high regional levels. Abrupt changes in Cr distribution in stream sediment coincide with stratigraphical boundaries, allowing drainage data to be used as a surrogate for whole-rock values

Jun 19, 1905

By Michael Zachariah, Art Miller, David Kittelson, Gib Ahlstrand

This report describes an investigation in which we used iron-doped diesel fuel to generate metal-bearing diesel particles and a subsequent analysis of the particles using transmission electron microscopy (TEM) and energy-dispersive spectroscopy (EDS). For this study, DPM was generated by a 1.5-L diesel engine and the fuel was doped with ferrocene to enhance the level of iron in the system. The exhaust particles were collected on TEM grids and analyzed using the Philips CM12 TEM/EDS instrument. Results show that when the iron-to-carbon (soot) ratio (Fe/C) in the engine is low, the exhaust particles have morphologies similar to those for the undoped case, but at a threshold Fe/C value of 0.013 (for this engine), homogeneously nucleated metallic nanoparticles are formed and begin agglomerating. The number and size of these nanoparticles increase with level of doping. Metal-bearing particles that span a wider size range are also formed. Agglomeration of metallic and carbon particles is observed in two distinct modes: attachment of iron primary particles (5–10 nm in diameter) to carbon agglomerates, and coagulation of iron agglomerates (20–200 nm in diameter) with carbon agglomerates. Results of this work imply that as new engine technologies reduce soot levels in the engine and/or levels of trace metals in the fuel are increased, the generation of metallic nanoparticles may ensue, creating a potential health concern. Keywords: Nanoparticles; Particulate emissions; Metallic particles; Metal emissions

By Walter Durst

On October 16, 1978, the Harnback open cut of Rheinische Braunkohlenwerke, the largest open cut ever planned, was officially put into operation. It will outperform all of the large open cuts known at present, both in its dimensions and in its annual output of overburden and coal. Present plans are to commence coal mining in 1983, although target production will only be achieved in 1995when the annual output will be 50 million tons of coal. Considering an overburden: coal ratio of 6: 1, this will involve the removal of approximately 300 million bank cubic metres of overburden. For overburden removal and coal mining, this open cut will use bucket-wheel excavators exclusively. It is planned to employ eight excavators with a daily output of 240,000 bank cubic metres each (Fig. 1). The transport of the overburden and coal to the dump and the power station, respectively, will be effected by 30Q0-mm-wide conveyors, running at a speed of 6 m/sec. The overburden will be dumped by spreaders having a boom length of 100 m, capable of dumping 240,000 bank cubic metres per day (Fig. 2). Such giants, of course, can only be used for extreme conditions . Their employment indicates that huge quantities of material can be handled economically for long periods. However, the use of bucket-wheel excavators is economic when daily outputs of 5,000 bank cubic metres are involved, in particular if direct backcasting of the overburden is not possible.

Jan 1, 1979

By Mohamed Ourriban, Stéphanie Somot, Éric Proulx, Jean-Sébastien Marois, Marjolaine Drouin, Paul Blatter, Ahmed Bouajila, Claude Gagnon

"The mining industry has to face increasing restrictions concerning the use of fresh water in Québec and throughout the world. Increasing recirculated water usage could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have a negative impact on mineral processing operations, thereby limiting the incentive for sustainable development initiatives. As a first step into selecting and testing remediation strategies, one of which being blending local waters, a mapping of process water quality (inorganic and organic fractions) allowed to locate zones in an industrial case study where fresh water is introduced into the circuit and to detect dissolution and precipitation zones. A complementary hydro-geochemical modeling study on water blends was also performed showing encouraging results towards the objectives of the project.INTRODUCTION The industry has to face increasing restrictions on the use of fresh water in Québec (Quebec Government, 2009) and throughout the world (Brown, 2003; UNESCO, 2006). The cost for the use of fresh water and for water management is highly variable and case-dependent (from 0.2 to up to 7 million dollars/year according to available private estimations, excluding the capital expenditure). It may be, or may become, significant for any plant; thus, risk assessment is of concern here. Using recirculated water could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have some positive and negative impacts on mineral processing operations (Janssen, 2003; Johnson, 2003; Rao and Finch, 1989). Negative impacts could limit the incentive for sustainable development initiatives. Water management strategies at mineral processing sites are supported both by a strategic plan and a water management plan. The strategic plan includes legal aspects, investment costs, potential benefits and various risk levels (Corder and Moran, 2006; Côte et al, 2006; Evans et al., 2006; MacIntosh and Merritt, 2003; McLellan et al., 2008; Merritt and MacIntosh, 2006; Robinson and Keddie, 2006; van Beers et al., 2007a; van Beers et al., 2007b; van Berkel, 2007). In practice, the strategic plan evaluates technical possibilities and costs of various scenarios, such as for example: bringing fresh water to the plant or recirculating waters, or using blends of both. Two important factors to consider in order to enhance the future production efficiency and to minimise risks are: the durability and the stability of the resource, both from quality and quantity points of view."

Jan 1, 2012

When Haematite Explorations Pty. Ltd. began prospecting for petroleum in 1960, there was only ill-defined geological evidence on the land bordering Bass Strait to support the belief that petroleum lay trapped in sedimentary formations beneath its shallow waters.A reconnaissance of the area, made in 1961 by the airborne magnetometer method, covered the waters and islands of the Strait and overlapped the Victorian and Tasmanian coasts. The survey indicated the presence of the Bass Basin (which is completely water-covered), assisted in outlining the Otway and Gippsland Basins, and showed that each basin contains sedimentary rocks over 10,000 ft thick. Information on the regional geology and minor volcanic activity was also obtained.Marine seismic surveys carried out from 1962 to 1965 defined these basins more accurately and showed the nature and structure of the thick sedimentary sections.Correlation of the seismic data with onshore wells identified the sediments as Tertiary and Mesozoic. Subdivisions of the former in all basins and the latter in the Otway Basin were made. These Tertiary and Mesozoic rocks are not seriously deformed and they have good prospects of containing petroleum.Possible structural and stratigraphic traps, recognized from the seismic record sections by petroleum geologists, are being tested by offshore drilling which began in 1964.

Jan 1, 1966

By J. A. Hudson, D. L. Millar

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: Rock engineering system performance monitoring using neural networks.) Synthetic and analytical approaches to objective-based design of rock engineering projects are discussed. Rock masses are considered as complex dynamic systems with components that concurrently interact with each other and their environment. The existence of a rock engineering system canon (i.e. a set of systems governing rules) is proposed. Its possible components are highlighted and an application is demonstrated using a "rock mass automaton" designed to simulate dynamic heat distribution in rock. In the example given, the canon implements the basic result from probability theory applied to the thermodynamics of solids. Rock engineering system performance is reduced to the mapping of the output of a rockmass to varying input (design) options, within the state space of the systems model. The Kohonen Self-Organising Map provides an extremely useful analytical tool to reduce the hyper-dimensionality of rock engineering system behaviour. Further, the hyper-dimensional state vector is mapped "quasiconformally" such that the neural map tends to spatially organise similar input state vectors, facilitating interpretation of rock engineering system behaviour (performance monitoring). Work is reported on the development and validation of the automation as a basis for an internal representation of the rock mass bahaviour. The results are reported of simulations compensating for the uncertainty of the exact mechanisms operating within the rock mass, using additive noise with the input state vector in the training stages of the self-organising map implementation. Initial work on adopting Grossberg's Adaptive Resonance Theory neural network architecture for classification of rock engineering systems behaviour is also presented

Apr 1, 1994

By Luís Marcelo Tavares, Marko Hilden, Malcolm Powell, Grant Ballantyne, Lian Liu

The t10 relationship developed by Narayanan and Whiten has underpinned a number of the JKMRC models and the characterisation of ore competence through impact testing with the drop weight tester. This usefulness is based on a consistent relationship between the t10 value and the overall size distribution that was noted for brittle rocks. However, like all characterisation tests this should be used only when the controlling conditions apply, which in this case is single impact breakage between two metal platens and within the range of sizes in which fragment sizes are normalizable. For any other mode of breakage the relationship should be confirmed before being applied. Soft ores or bimodal ores with widely different competence between dominant components have non-typical breakage signatures. Breakage via single point impact abrasion, compressed-bed breakage, low-energy surface breakage and incremental breakage, to name some of the other breakage modes, do not obey the general t10 relationship, so their outcomes cannot be used to provide a direct comparison. Inappropriate use of the t10 parameter can result in misleading conclusions about efficiency of energy use. These issues and alternative comparison techniques are presented and discussed in terms of choosing appropriate measures of efficiency of breakage, ore competence and energy required for comminution.

Jan 1, 2014

Experimental investigations were made into the decoppering of lead, tin, and bismuth using a technique which approximates on the small scale to industrial practice.Decoppering lead with sulphur alone in the absence of tin and silver did not proceed to low copper values. With a minimum of 0·02 per cent Ag or 0·10 per cent Sn, lead was decoppered to less than 0·01 per cent Cuby stirring with 0·2 per cent S over 10 min. Decoppering of tin or bismuth proceeded rapidly to very low levels in the absence of any "catalytic" impurities, at any rate in excess of those concentrations normally encountered in commercially pure tin or bismuth.

Jan 1, 1971

By J. D. Morgan

The US economy continued to grow steadily in 1988, reaching an annual rate of $5 trillion in the last quarter (US trillion = 1012). The value of domestically processed mineral-based materi¬als rose 20% to $300 billion (US billion 109). The value of metals produced from US ores rose 40% to more than $10 billion, industrial minerals rose 6%' to $20 billion, and recycled scrap more than doubled to $10 billion. Increasing economic activity stimulated metal prices. Yearly lows and highs were 95 cents and $1.68 for copper, 52 cents, and $1.30 for aluminum, 34 cents and 42 cents for lead, and 43 cents and 75 cents for zinc. A number of mining and metal companies experienced significantly increased profitability. Consumer demand strongly affects mining because the US economy is relatively saturated with long-lived products. Consumer, mortgage, and Federal debt continued to rise. About 246 million US citizens already possess 170 million licensed motor vehicles and 100 million dwelling units. New car production remained at the 1987 level of 7.1 million units. Truck and bus production, however, rose 7% to 4.1 million units. New housing starts fell 7% to 1.5 million units. Imports supplied a significant proportion of total US consumption of several important mineral materials. By year-end, imports of crude and refined petroleum exceeded domestic crude oil production. Such imports cost $42 billion. Imports of nonfuel mineral-based materials were valued at $44 billion and exports at $35 billion. The US and Canada-the world's two largest trading partners-consummated a historic free trade agreement. In February, President Reagan transferred responsibility for stockpiling strategic and critical materials to the Secretary of Defense. And, in July, the GSA group that bought, stored, rotated, and sold stockpiled materials was transferred to the Defense Department's Defense Logistics Agency. Concern about apartheid in South Africa continued, resulting in increasing attention to chromium, manganese, platinum-group metals, cobalt, vanadium, and gold. The Defense Production Act, authorizing priorities and allocations, supply expansions, voluntary agreements, and the National Defense Executive Reserve, was amended to include provisions for averting harm to national security from foreign takeovers. The DPAct, in effect through September 1989, is now up for further extension. Under the Act, the US Bureau of Mines maintains the Emergency Minerals Administration. During the year, consultations were held with Canada to strengthen the North American Defense Industrial Base. Coal production, 60% from open pits, rose 5% to 870 Mt (960 million st). Nearly four-fifths was burned to generate 57% of US electricity. Exports included 56 Mt (62 million st) of metallur- gical coal and 29 Mt (32 million st) of steam coal, with a total value of $4 billion. Domestic petroleum produc¬tion fell 2% to 574 hm3 (3.6 billion bbl). Uranium mining, including recovery from phosphates, was unchanged at 5.9 kt (6500 st). Nonfuel minerals Major metals Raw steel production-a major con¬sumer of many minerals-rose 14% to 92 Mt (102 million st). Domestic iron ore production rose 25% to 59 Mt (65 million st), about 96% pelletized. Net imports rose 37% to 16 Mt (18 million st). Raw steelmaking capacity of 102 Mt (112 million st) was unchanged. Voluntary Restraint Agreements with 21 steel exporting nations limited im¬port penetration to about 20% of the domestic market. Domestic producers of bulk ferroal¬loys of chromium, manganese, and sili¬con operated at about 75% of capacity. The US mined no manganese or chro-

Jan 1, 1989

By D. S. Richards

Computers have revolutionized the collection of data on modern mines. Never before has it been possible to collect data from all aspects of the mining value chain at rates now common. With this has come a new challenge. Deriving information from these copious amounts of data and disseminating it. This problem is being exacerbated by technical software systems, which use proprietary and binary data formats that severely inhibit the flow of data and information both across departments and the larger organization. Generally this had led to data duplication and data redundancy. The Gemcom Enterprise Mining System (GEMS) makes use of industry standard, secure and open databases for all its data objects. It manages multiple users accessing the same bits and bytes in the database, preventing data duplication and redundancy. Developed in the Microsoft BackOffice ® environment, GEMS is also able to leverage the enormous amount of tools available in this environment, whether it’s for e-mail notification, reporting or data capture. Microsoft’s® Active Server Pages are one of these tools. These are standards used to create dynamic and interactive web pages with links into databases and many other objects. The real example outlined in the text, demonstrates how a user anywhere in the world is able to login to a web page and run a query that returns a report with vector plots of performance for the user-selected time frame. As integration is tightened between the various components of the mining value chain, the importance and reliance on ASP pages will grow as the need for management information tools develops. Keywords: mines, computers, ASP, GEMS, integration, Microsoft, Management Information.

Jan 1, 2003

By F. Calizaya

The Western Mining Training and Translation Center is a consortium of four universities devoted to developing educational and training projects to reduce the incidence/accident rates in the mining industry. The center consists of Missouri University of Science and Technology, Montana Tech, the Colorado School of Mines and the University of Utah. It is fully funded by the National Institute for Occupational Safety and Health (NIOSH). The center manages 15 educational projects and one translation project. Hazard Identification and Risk Assessment (HIRA) for Small Mines is an educational project managed by the University of Utah. The objectives of this project are to identify critical mine hazards, assess risks; outline procedures to reduce accident/incident rates in small mines in the western United States and to train mine workers and super-visors on HIRA in each participating mine. To accomplish these objectives, the HIRA personnel visited 15 small mines in Utah, Colorado, Nevada and California. At these mines, most operators were employing independent contractors to perform several tasks ranging from drilling, blasting and mucking of rock at the work site to hauling ore to a processing plant. The operation of diesel-powered equipment was one of the major tasks performed by the contractors. This article presents three case studies in which contract workers performed a number of tasks with no reportable incidents but did so unsafely. It also highlights the training received by most contractors, the constraints imposed upon them and the safety hazards to which they are exposed most frequently.

Jan 1, 2008

By Helvio Pessanha Guimarães Santafé Jr.

The coir fiber extracted from the husk of the coconut has been extensively used as polymer composite reinforcement in a variety of industrial applications ranging from civil construction to automobile seat cushions. The hydrophilic coir fiber does not act as an effective reinforcement owing to its low interfacial strength with hydrophobic polymers. As a consequence, coir fiber composites display relatively low mechanical strength. The objective of this work was to investigate the effect of an acetylation treatment of the coir fiber surface on the mechanical behavior of epoxy composites with amounts of fibers up to 30% in volume. Coir fibers were immersed in an acid solution of acetic anhydride for one hour, washed and dried, before mixing with DGEBA/TETA epoxy to fabricate the composites. Flexural mechanical properties were obtained by bend tests. The results showed significant differences to similar composites with alkali treated coir fibers that have been previously investigated.

Jan 1, 2010

By Sadegh Firoozi

Experiments measuring the kinetics of oxidation and making visual observations of the oxidation of approximately 6 g static lead baths containing arsenic, antimony and tin were conducted in the temperature range from 500 to 600 oC. A range of repeatable behaviours were observed, notably: the formation of a coherent, solid oxide layers on pure lead and lead-tin alloys; the formation of liquid oxide droplets during the initial oxidation of lead-arsenic and lead-antimony alloys and the eventual formation of a complete oxide layer covering the entire free surface of these alloys. Thermogravimetric measurements revealed that the rate of oxygen uptake was strongly influenced by the form of oxides being generated at the melt/gas interface. Compared to the rates of oxidation of pure lead, arsenic increased the rate of oxygen uptake throughout the temperature range via the formation of liquid oxidation products. The presence of antimony resulted in a moderate increase in the rate of oxygen uptake as compared to arsenic. Tin was effective in lowering the rate of oxidation even in the presence of arsenic because the oxidation product was always a coherent layer that acted as a physical barrier to oxygen transport to the underlying alloy.

Jan 1, 2006

By Agnes Y. Lee

As part of the U.S. Bureau of Mines program to improve base metal leach systems, pressure leaching of galena (PbS) concentrates in fluosilicic acid (H2SiF6) solution was investigated. Lead extraction was 93 pct when PbS was pressure leached in H2SiF6 at 95° C with 2OO-psig O2 pressure for 40 min, using ferric nitrate [Fe(N03)3] as a catalyst. The effects of several catalysts, O2 pressure, time, and acid concentration on leaching were determined. The purified leach solution was electrowon to recover high-purity Pb metal. The H2SiF6 used in leaching and electrowinning can be recycled continuously. A flow diagram was proposed based on this investigation. Elemental sulfur (SO) was recovered from the leach residue by solvent extraction. A method was also developed for treating the flnal residue to segregate the important byproduct elements such as Ag, Cu, and Zn and enable their recovery by standard commercial processes.

Jan 1, 1990

By P. A. Plunkert, D. E. Morse, Pui-Kwan Tse, W. D. Menzie, Lucy McCartan, J. F. Papp

China’s burgeoning economy is responsible for a major share of recent world mineral consumption increases. In addition to factors traditionally recognized in market economies1 and factors unique to specific commodities, Chinese consumption now plays a major and increasingly important role in energy and mineral markets for many commodities, such as aluminum, copper, iron and steel, and oil. China has the world’s second largest economy after the United States. And its long-term importance to the minerals markets is even greater than indicated by its gross domestic product (GDP), which is currently less than two-thirds of that of the United States (Table 1). This is because China’s rising standard of living is accompanied by rapid industrialization and urbanization. Its consumption of mineral materials for infrastructure development for its very large population is significantly greater per capita than that of such developed economies as the United States, the European Union and Japan. In other words, China’s per capita production is rising at a rapid rate and will probably continue to do so for many years.

Jan 1, 2006

This paper gives a general description of mining operations at the Mount Morgan Open Cut. Certain features such as blast hole diamond drilling, which may be of particular interest, have been described in detail. The paper is covered by the following headings:-1. History2. Ore Reserves and Production Data3. Mining Methodsa. Design and Layout of the Open Cut.b. Overburden and Ore Breaking.c. Loading and Transport of Ore and Overburden.d. Transport of Men and Supplies.e. Survey and Assay.f. Drainage.4. Power and Compressed Air5. Mining Equipmenta. Shovels.b. Mine Transport.c. Dozer Tractors.d. Drill Shop.6. CostsHISTORYIn order to appreciate fully the design of the present Open Cut at Mount Morgan, a brief outline of the Mine's history and past mining methods is necessary. In 1882 the Mount Morgan Syndicate began to mine this large gold-copper orebody by small hill-top quarries...

Jan 1, 1952

By T. M. Barczak

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of ?topping off? the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

Jan 1, 2008

Pillars in underground limestone mines are required to support the overburden and provide a safe, stable working environment for mining personnel and equipment. Pillar stability was assessed by the National Institute for Occupational Safety and Health in underground limestone mines in the Eastern and Midwestern United States. It was found that current mine layouts have been successful in providing support to the overburden, while a small number of isolated pillar failures were observed. The stable pillar layouts and failed pillars were plotted on a chart that demonstrates the relationship between pillar width-to-height ratio and pillar stress. The results show that pillar failures occurred at the lower range of width-to-height ratios and can occur at relatively low stress levels. Zones indicating the potential risk of pillar instability are shown on the chart, based on hazards associated with the onset of rib spalling, large angular discontinuities and unconfined pillars. The chart can assist limestone mine planners to evaluate potential instability in current or new pillar layouts that are similar to those included on the stability chart.

Jan 1, 2008