Search Documents

By S. Akhtar

Interstitial compounds of iron, cobalt, and nickel, and their binary and ternary mixtures with silver, gold, palladium, and platinum were prepared and tested as fuel cell catalysts. The first step in the preparation of the interstitial compounds consisted of preparing finely divided metals. This was done either by the Raney method or by reduction of precipitated hydroxides of the metals. The finely divided reduced metals were then treated with carbon-and/or nitrogen-containing gases to prepare their carbides, nitrides, and nitrocarbides. The materials were tested for cathodic activity towards O2 and for anodic activity towards H2, C3H8, NH3, CO, and N2H4 in acid and alkaline electrolytes at 25° to 90° C in half-cell assemblies. Samples of carbided and nitrocarbided INi-lAg-1Au were about one fifth as active as Pt-black in the reduction of O2 in 35 percent KOH solution, whereas the activities of several interstitial preparations exceeded the activity of Pt-black in the reduction of O2 in 12M KOH containing N2H4. Nitrocarbides of x-Fe2C, 3Ni-1Au, and 1Ni-3Au were effective catalysts for oxidizing N2H4 in liquid NH3 containing NH4SCN. Corrosion of the catalysts by electrolytes was severe in many cases.

Jan 1, 1970

A field method combining solvent extraction and paper partition chromatography permits a simple and rapid semiquantitative estimation of gold in siliceous, argillaceous and sulphide ores. The method will facilitate the eyaluation of prospect samples in which the gold is too fine for separation by panning.Ethyl alcohol-hydrobromic acid mixtures are suitable for chromatographic development of the gold complex, and give clear reproducible definition of the gold zone. Substitution of commercial "methylated spirits" for the ethyl alcohol gives equally good definition, improving the potential of the method for field use.A batch of six samples in the range of 0·5 to 5·0 dwt/ton can be completed in two hours. The range may be extended by simple modification to higher or lower values.INTRODUCTIONIn a chromatographic method described previously (Lever 1958, Nevill and Lever 1959), gold from a standard volume of ore clamped between -plate glass was extracted by aqua regia on to the paper. After cautious drying the chromatogram was developed by an ethyl acetate-nitric acid-water mixture and gold was identified by spraying with stannous chloride solution. Sensitivity of the method in the low range was poor. The brown line obtained in the 1-3 dw/j ton range, caused by movement of gold in the reduced form, was not considered to be a satisfactory confirmation of the presence of gold. It was felt that the method would be improved by using a more elegant extraction and applying developing conditions which would produce a well defined purple line at all gold values. Iron was a limiting factor, and a method of eliminating its interference was needed.The method now developed overcomes these shortcomings, and gives a reliable result with a purple line for assay values of 0·5 dwtjton and over. Gold is dissolved from an...

Jan 1, 1964

By V. Labiouse, P. K. Kaiser, F. Descoeudres, F. Rojat

In this paper some failure phenomena observed in the crossing of brittle rock formations at the Lötschberg base tunnel are presented. A brittle failure criteria, recently developed by Canadian researchers, is applied through finite element calculations together with a semi-empirical failure criterion, to explain these behaviours. Good agreement is found between predicted and observed failures at the tunnel walls. This study also shows some of the limitations of this approach. Dans cet article sont présentés certains phénomènes de rupture observés durant la traversée de zones de roches fragiles lors de l’excavation du tunnel du Lötschberg. Un critère de rupture développé récemment par la recherche canadienne est utilisé à travers des calculs par éléments finis. En parallèle, les résultats sont comparés avec ceux d’un critère semi-empirique. Au niveau des parements, l’ampleur des ruptures observées est assez proche des résultats de calcul. Cette étude a également permis de mettre en avant certaines limites de l’approche choisie. In diesem Artikel werden verschiedene Brucharten dargestellt, die bei der Durchfahrung von sprödem Gestein im Rahmen des Ausbaus des Lötschberg-Basistunnels beobachtet wurden. Zur Erklärung des vorliegenden Verhaltens wurden die erst kürzlich in Kanada entwickelten Theorien zur Beschreibung von Sprödbrüchen herangezogen und bei der Berechnung mittels der Finite-Elemente-Methode und eines semi-empirischen Kriteriums angewendet. Die so vorhergesagten Versagenszonen an den Tunnelwänden stimmen mit den Beobachtungen gut überein. Die Studie hat auch dazu beigetragen, die bei der Anwendung des Lösungsansatzes angetroffenen Schwierigkeiten aufzuzeigen.

Jan 1, 2003

By Frederick M. Fowkes

Dusts can be filtered out of air streams onto polymer surfaces by electrostatic trapping resulting from the spontaneous transfer of electrons upon contact between dust particles and the polymer surfaces. Such spontaneous contact electrification has been studied quantitatively in this contract with the aid of modern semiconductor charge-sensors with the aim of determining what basic principles govern the sign and magnitude of contact electrification. Information obtained by capacitance-voltage measurements of thin polymer films on silicon showed that charges as large as 4 x 1012 electrons per cm2 develop spontaneously, and that such a charge gives adhesional forces of 165 pounds per square inch (11 atmospheres). Direct measurement of dust polymer contact electrification, using silicon surface channel conductance sensors, also showed spontaneous charges of more than 1012 electrons per cm2. Some polymers can either donate or accept electrons. These included chlorinated polyethylene, chlorinated polypropylene, polyethylmethacrylate, and a copolymer of maleic anhydride with n-octadecylvinylether. Other polymers never accepted electrons but could donate electrons; these included polystyrene, pulychlorostyrune, polyvinylchloride, polyvinylacetate, a polycarbonate (Lexan), and cellulose tributyrate. Contact electrification studies were made with dusts (coal dust, a channel black, or a silica powder) contacting thin films of various polymers solvent-cast onto the semiconductor charge-sensor. Sometimes charging was instantaneous and sometimes slower, but in all but one case (coal dust on a copolymer of maleic anhydride with n-octadecylvinyl ether) the charge trunsfer was a donation of electrons by the polymer to the dust. Some

Jan 1, 1973

By Ailton da Silva Ferreira

Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of curaua fibers. Both TGA and DTG curves were analyzed to determine the effect of the curaua fiber on the thermal resistance of the composites. It was found that the curaua fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.

Jan 1, 2010

By G. Hakes

A data bank on bolter technology was assembled which included state-of-the-art industrial equipment as well as new equipment currently under development for the U.S. Bureau of Mines. This information was augmented by field visits to selected USBM contractors, mine operators and others for the purpose of obtaining a thorough understanding of present coal mine roof bolting safety and productivity problems. These direct contacts provided valuable insight regarding requirements for new bolting equipment necessary to assure wide user acceptance. Using this background material and information, a series of roof bolter concepts was developed offering improved operator safety with minimum impact on productivity. The concepts developed utilize existing componentry and technology wherever possible. All of the concepts feature a fully protected operator station located 6' to 10' outby the active bolt line and the hazardous rotating machinery.

Jan 1, 1978

By Richard Mainiero

In any construction project involving explosives, care must be taken to protect workers from carbon monoxide (CO) generated by blasting operations. CO is an odorless, colorless gas that can cause illness and death by asphyxiation. In general, the first symptoms include headache, fatigue and lightheadedness. At higher exposures to CO, skin flushing, rapid heart rate, and lowered blood pressure occur. At ever, higher exposure levels, decreased attention span is followed by nausea, vomiting, unpaired coordination, fainting, coma, convulsions and, finally, death. The detonation of explosives in blasting operations generates a range of toxic fumes, but CO is the most insidious because it is colorless, odor less, and is long lasting, since it is not readily removed try reaction with ground water, soil or rock. Additionally CO is generated in relatively large quantities compared to other toxic: fumes. CO may continue to seep out of blasted material long after the odor commonly associated with detonated explosives has dissipated. It is never safe to assume as confined space in the vicinity of a blast is clear of toxic fumes. CO may be present even if the area looks Clear and many hours have passed since the last blast.

Jan 1, 2000

By R. B. Krog

As part of its mining health and safety research program, the National Institute for Occupational Safety and Health (NIOSH) conducted a longwall methane emission and mining time study at a mine operating in the Pittsburgh Coalbed to access the methane emission consequences of mining a longer face. The methane emission contributors from the mining of a longwall face are: 1) gas released from the coal broken by the shearer, 2) gas emitted from the coal on the face conveyor, 3) gas emitted from the coal transported on the belt, and 4) background gas emitted from the coal face and from the adjoining ribs. Based on the results of the study, a set of site-specific mathematical formulas and constants were developed to characterize each of the four longwall emission contributors. The mathematical formulas were then applied to longer longwall face mining scenarios to predict the methane emissions from these faces.

Jan 1, 2006

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to make these questionnaires as complete as possible.

Jan 1, 1963

By Martin Smirlock

A novel instrumentation system has been developed which enables simple, quick, and accurate measurement of vehicular dynamics within low speed ranges. The system, consisting of a microwave transceiver and microprocessor data acquisition and reduction system, measures the deceleration dynamics of low-speed mining and construction equipment. It makes the basic measurement, calculates key parameters such as average deceleration, initial velocity, stopping distance, and brake system delay time, and produces autoscaled graphs of velocity, acceleration, and displacement versus time.

Jan 1, 1981

By Parry. V. F.

"SUMMARY This report reviews the status of the packaged-for industry as of 1941. A field study was made of 35 representative plants to obtain technics and economic data on different types of processes used to make packaged fuel in the Central States. The report includes a classification of processes, photographs of typical operations, designs of different plants, an analysis of costs of manufacture, and a study of the physical and chemical properties of fuel cubes.It was observed that many of the smaller plants were having troubles in the manufacture of packaged fuel as the price of materials and costs of labor advanced toward the higher levels of 1942. In some instances, the total cost of manufacture was as high as $5.00 per ton, while in the better, medium-sized plants it was approximately $3.25 per ton. The direct manufacturing costs, excluding investment and depreciation, ranged from $3.17 to $2.37. These costs permit almost no profit at small plants when packaged fuel sells for the same price as competing lump coal under conditions existing in 1941-42.It was found that the predominant troubles in plants were due to inadequate drying and insufficient mixing of the starch binder. It was ob¬served that in the better plants, where proper mixing of binder was attained high-quality packages were made if 50 to 70 percent of the moisture was removed in the drying ovens. Experimental data obtained in the laboratory show the relationship between the temperature of dry air and the time required to remove different percentages of moisture in wrapped orunwrapped coal cubes.The average physical and chemical properties of fuel cubes made by five processes are listed, and tentative standards for minimum physical qualities and methods for measuring quantity are giver."

Jun 1, 1944

By M R. Stevens

The Kauri Block (Hauraki Hill) andMatawai Valley epithermal vein systems, near Coromandel township, are hosted by hydrothermally altered Miocene andesites and Mesozoic greywackes of the Coromandel VolcanicZone. The hydrological setting of both geothermal systems was probably that of an andesitic volcanic arc. Two types of veins are recognised: 1. Simple veins composed of fine comb quartz, and 2. Complex (breccia) veins composed of vein fragments of sulphide-bearing, chalcedonic silica cemented by saccharoidal and fine comb quartz.   Pyrite, arsenopyrite, marcasite, and gold form the ore minerals. Both deposits historically exploited hypogene and supergene bonanza gold.   At Hauraki Hill, breccia veins up to 7m wide contain abundant fragments of recrystallised colloform banded-crustiform textured quartz veins ('Golden Cross' style) and were probably major channels for ascending deep mineralising fluids. Alteration assemblages are zoned with the higher elevations of Hauraki Hill-Bunkers Hill characterised by strong kaolinite alteration whereas deeper levels are dominated by illitic clays.   At Matawai, complex veins and hydrothermal breccias pinch and swell, and inflect, within a total width of veining and alteration that exceeds 50 m. The greywacke host rocks are altered to an assemblage of illitesmectite, quartz, chlorite and pyrite although there are pockets of kaolinite.   The proposed genesis of veins and ores in both deposits invokes episodic rapid mixing (quenching) of hot mineralising reservoir fluids with cool acid condensate waters, whilst acidification and increased fO2 triggered gold deposition. These hydrothermal systems heated up during their later stages and at Matawai visible gold was deposited from a late mesothermal stage. The main conclusion is that the northwest CVZ has excellent potential for large gold deposits (= 30 tonnes contained gold).

Jan 1, 1993

By G. H. Keith

Electrowon tungsten powders were investigated with respect to consolidation, fabrication, and mechanical properties. Sheet, 0.03 inch thick, was produced and its tensile strength measured between 250° and 1,935° C. The large particle size of electrowon tungsten effectively precluded sintering to a density sufficient to allow hot working to sheet or bar. The powders were consolidated by die pressing to 70-percent density, sheathing in molybdenum, and high-energy-rate extruding to either round or sheet bar of 100-percent density. The material was then rolled conventionally to sheet. The mechanical properties of the sheet prepared from the electrowon powders compared favorably with those reported in the literature for sheet prepared from commercially produced hydrogen-reduced powder.

Jan 1, 1970

By J. F. Barkley

To reduce fuel consumption in industrial and commercial fuel-burning plants throughout the Nation, cooperative efforts of thousands of individuals are required. These individuals are scattered over the country and hold various positions in thousands of independent establishments. To accomplish as much as possible on this problem during the Second World War, it was decided that personal contact with fuel users was absolutely necessary; publicity, although an important factor, could not by itself give satisfactory and needed results. It was planned to have qualified engineers visit commercial establishments to go over with them the problem of reducing their fuel consumption. The specific plan, toward which all efforts aimed and around which the rest of the program revolved, consisted in brief of 1. Conference of visiting engineer with management to obtain cooperation. 2. Appointment by management of a plant employee as fuel "waste chaser." 3. Work of engineer with "waste chaser" and, if appropriate, with plant operators on most efficient operation of equipment.

Jan 1, 1948

By R. Karl Zipf, Francois E. Heuze

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINETAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress-strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory-scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle () for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

The poor reconciliation between the values of estimated and actual grades can cause major economic losses to the mining industry. In a mining operation grade reconciliation is comparing the values of estimated grade calculated in exploration stage with actual grade obtained from blastholes' data. Many different factors affect the degree of reconciliation in a mining operation. In this paper we investigate the factors related to estimated grade which affects the reconciliation process in the exploration stage of the orebody. These factors are the sources of uncertainty in the rest of mine life. In this area the most important factors are inherent variability, statistical uncertainty and systematic uncertainty. A probabilistic model was presented to model each source of uncertainty. The implementation of proposed model was checked and its validity was investigated using real data in an iron open pit mine in Iran.

Dec 6, 2010

By A. Ochieng

Solids suspension influences the quality of mixing and energy requirement in a solid-liquid system, both of which determine the efficiency of industrial processes such as nickel precipitation. Nickel solids concentration distribution in a stirred tank was investigated using computational fluid dynamics (CFD) and experimental methods. The concentration distribution of the nickel solids was compared with that of sand and glass. The laser Doppler velocimetry (LDV) method was used to measure the velocity field for the liquid-only system and an optical technique was employed to determine the axial solids concentration distribution. Regions of in homogeneity in the tank were identified. It was found that, for a given solids loading, the solids concentration distribution depended on both particle size and particle size distribution. High solids loadings were investigated and a difference in the concentration distribution pattern was obtained with nickel, flint glass and sand particles. The CFD simulation results highlighted problems that could be associated with some conventional experimental methods of determining solids concentration distribution in a stirred tank. Keywords: nickel; CFD; simulation; mixing; solids suspension.

Jan 1, 2010

By Yiming Sun

The 5-mile long Bay Tunnel is a major water supply facility to be constructed under the San Francisco Bay and adjacent marshlands between the San Andreas Fault to the west and the Hayward Fault to the east. The tunnel will have a two-pass lining system consisting of a watertight precast concrete segmental initial lining and a welded steel pipe final lining. Considering the Bay Tunnel?s location between two major active faults, the design earthquake produces a significant peak ground acceleration estimated at approximately 0.6g. To develop a design that can achieve the seismic performance objectives, full dynamic seismic analyses were performed using site-specific earthquake time histories. The analyses considered soil-structure interaction and an evaluation of the transverse and longitudinal effects of the design earthquake. This paper describes the seismic analyses and the design measures recommended to minimize potential adverse effects of the design earthquake on the tunnel final lining.

Jan 1, 2008

By I. Fedotov

One of the most effective methods of metal surface heat treatment is through laser hardening. In most cases, laser parameters are determined experimentally, which is expensive and time-consuming. A mathematical model for the surface heat treatment process will allow a significant decrease in costs, and reduce the time required for optimization. In the present work, the authors present a mathematical model for laser heat treatment with forced cooling which can be applied to medium carbon steel. The model is based on a three-dimensional heat transfer equation using Green?s function. The model allows one to calculate the temperature of the treated steel at different depths below the surface with and without cooling, for set values of the laser power and travelling speed, when the heat transfer coefficient is a known constant. It also takes variations in the radiation adsorption coefficient on the metal surface and laser beam spot size into account. The model was illustrated by comparing calculated and experimental temperature profiles of mild carbon steel with 0.5% C with and without cooling. A reasonably good agreement was achieved between experimental and predicted values to ensure that a high enough austenizing temperature with short enough cooling time was reached for direct martensite formation. It also predicted the depth of treatment accurately. The incorporation of cooling in the model substantially improves previous models based on heat transfer only. It delivers a tool that can with a reasonable accuracy predict the depth of surface heat treatment and cooling time required from operational parameters, such as laser power, speed of motion, and distance between laser and cooling source, that can be controlled in the work set-up. This can eliminate trial and error efforts and result insignificant time and cost savings. Keywords Laser, surface treatment, martensite transformation, carbon steel, heat treatment.

Jan 1, 2011

By S. Ngidi

Palabora Mining Company operates a low grade underground copper mine situated in the Limpopo Province, South Africa. Full production was first reached in May 2005 after a successful transition from an open pit operation to an underground block cave operation. The operation faces a number of technical and operational challenges, not the least being fragmentation of a competent rock mass and external dilution. The cave is subdivided into three main sectors being the east, the west and the central sectors. Caving was initiated from the weaker central sector, which has the majority of its drawpoints located directly under the open pit bottom currently filled with about 130 million tons of waste material from the pit wall failure incurred in 2004. About 48% of the ore reserve has to be extracted from the western sector, which has a much courser fragmentation compared to the other two sectors and only 25% from the central sector with the finest fragmentation. The main constraint during the ramp-up stage has been secondary breaking of drawpoint blockages. Ground-breaking secondary breaking and cave management initiatives and practices have made it possible for Palabora to realize and sustain high production rates.

Jan 1, 2007