Search Documents

By J. L. Bowlby

TWO years ago, at the annual meeting of this Society, the writer presented a paper dealing with various aspects of the water problems existing in the Cape Breton coal-mining area. Much of that paper was of a theoretical nature, in that an attempt was made to get at the fundamental principles underlying the problems, in order to establish a sort of background against which future results could be laid. Up to that time, only Central power plant in Glace Bay had been under observation, and, since the work had been in progress only a year, it was recognized that there were strong possibilities that certain variations in procedure might have to be introduced as w; became better acquainted with our problem. We were by no means certain that we had covered all the facts of the case. The present paper will therefore be of the nature of a progress report, rather than a formal contribution to the Society. Subjects of a theoretical or academic nature will be avoided as far as possible, attention being confined chiefly to the results obtained during the past two years. In looking over the work with low-pressure boilers, there are certain general conclusions that can apparently be safely drawn. Wherever possible, proper operating conditions will be expressed in terms of appropriate units. Absence of corrosion in boilers where the alkalinity has been maintained within the pH range 11.0 to 11.4 forces one to the conclusion that these are safe working limits. Previous experience had shown that corrosion would occur if the alkalinity were much reduced. Higher alkalinities are un-necessary, more expensive, and are said to introduce the possibility of pitting. We made no attempt to obtain quantitative data in respect to pitting. It is said to occur at pH 12.0. Consequently, conditions of alkalinity were main-tained well below this figure. In the above paragraph, the pH range 11.0 to 11.4 applies to boiler waters which have received the lime and soda treatment. The general practice, when this treatment is employed, is to use 1.0 lb. lime to 7.0 lb. washing soda. At Central power plant, soda-ash is at present substituted for washing soda, the equivalent proportions being kept the same. But not all the plants are on the lime and soda treatment. At Waterford Lake, a 1: 1 mixture of soda-ash and trisodium phosphate is satisfactorily employed, and in Sydney Mines and at No. 3 power plant in Sydney, good results are being obtained at a somewhat greater cost with a commercial phosphate treatment.

Jan 1, 1936

By Andrea Koschinsky

Numerous hydrothermal vents occur along the Earth?s oceanic spreading axes documenting the reaction of seawater with hot magmatic rocks. The circulation of seawater through the oceanic crust, the interaction with hot rocks in the crust, and the subsequent discharge of hot metal- and gas-rich fluids into the ocean have significant implications for the cycling of material and energy on Earth. Until recently, hydrothermal activity was unknown from the Mid-Atlantic Ridge (MAR) south of the Equator where the MAR is offset by about 1000 km at the St. Paul?s and Romanche fracture zones. During a British cruise in February/March 2005, the first active hydrothermal vent field was discovered on the southern MAR at 5°S. During our follow-up cruise M64/1 in April 2005, the first samples from this vent field were recovered with the ROV QUEST (Univ. Bremen) and analyzed onboard. The high-temperature vent field is situated in a water depth of 2990 m along a line of collapse pits within a large basaltic sheet flow. A diffuse, low-temperature field occurs in a jumbled sheet flow few hundred meters to the east with warm water streaming out of cavities between lava blocks. Here we show for the first time that boiling fluids of ~400°C are emanating from sulfide-bearing vents at a depth of about 3000 m at a slow-spreading Mid-Atlantic Ridge segment. Although this segment is composed of thick basaltic crust, these fluids are dominated by hydrogen relative to methane. Whereas the active chimneys consist of pyrrhotite, chalcopyrite, and isocubanite, the mineral association hematite-magnetite-pyrite occurs in the inactive chimneys suggesting that the fluids became more reducing in present times. The high hydrogen contents and the high temperature of the fluids as well as the change to more reducing conditions are most likely related to a young volcanic eruption event some 300 m east of the hydrothermal field. The presence of hematite and magnetite may indicate that the upflow zone or even the reaction zone at 5°S used to be more oxidized then at other MOR sites, where the hydrothermal fluids are commonly buffered by the pyrite-pyrrhotite-magnetite (PPM) buffer. Consequently, high iron contents and high hydrogen/methane ratios occur in high temperature fluids from basaltic host rocks rather than being restricted to ultramafic host rocks. Faunal communities at the South Atlantic vents largely resemble those from the North Atlantic vents implying that the large Equatorial fracture zones do not inhibit or obstruct faunal exchange along the Mid-Atlantic Ridge.

Jan 1, 2005

Some Otago quartz veins display spectacular open-space filling textures indicative of shallow formation. Fluid inclusions in some such veins show that fluid immiscibility occured before or during mineral deposition. This immiscibility or 'boiling' occured at depths ranging from about 3 km to within as little as about 100 metres of the paleo-surface. Temperatures of mineralization range from 190 - 250¦C. Metals deposited in these veins include: Au(+Ag), Hg, Sb and As. Hydrothermal alteration is confined to minor silicifation of immediate wall-rock schist, less than about two metres from the veins. These veins have some similarities to classical epithermal systems elsewhere in the world, although wall-rock alteration is much less developed in Otago. From analogy to these classical epithermal systems, it is speculated that gold mineralisation may be found beneath Otago stibnite and cinnabar localities.

Jan 1, 1987

By Harvey W. Parker

Our industry has developed to the skilled, experienced and productive industry that we now enjoy as a result of the visions of great engineers throughout history, but, in particular for their visions in the last 1 centuries. Unfortunately for our forefathers, the technology lagged so far behind that these exceptional visions could not be realized for decades, sometimes for a century. All that has changed in recent time and many bold and visionary projects can now be constructed and operated because of dramatic advances in technology. Before, say, 1950, tunnel technology developed very slowly. However, technology is now developing at such a fast rate that planners and decision makers are challenged to stay ahead. Moreover, new technology will develop during the lifetime of any project that can dramatically improve under-ground space projects. One of the best examples of this technological advancement is that of closed-face TBMs which now make tunneling feasible in previously impossible ground conditions. Since it usually takes a decade or more to plan, overcome environmental and political issues, construct, and put into service major projects, planners and designers are challenged by the changes in technology that occurs during the long time span of planning and construction. This is particularly true of large infrastructure projects such as transportation, water and wastewater systems and other major underground schemes. Also, since the serviceable life of many of these tunnels is often over one century, planners must consider not only lessons learned from the past but also what new concepts and innovations may develop over an extremely long time. These and other issues create a great challenge to planners and illustrate the great importance of careful but creative vision and flexibility during planning of long-term tunnel and underground space projects.

Jan 1, 2008

By Theo Lehner

"The Boliden Rönnskär Smelter operates in the European Context of tight EH&S limits, with ever increasing regulations and tribulations. The near future promises to bring new burdens in the form of C02 trading, miners and pre-treaters increased appetite for a larger share of contained values, and changing compositions and competition in raw materials. On the other hand, European Smelters such as Rönnskär, Harjavalta have demonstrated an astonishing power of survival. This presentation lists and comments on current challenges but opportunities for increased survival power are also presented. One example of the latter is the ongoing investment into increased treatment capacity for e-scrap.UPDATE ON RÖNNSKÄR OPERATIONSThe Rönnskär Smelter has achieved 80 years of age with no signs of retirement. The smelter is most active in spite of its age! And it has undergone some face lift operations to maintain its attractiveness.Raw material, processing facilities and a market for the products are some essential prerequisites for a viable operation. To justify long term survival, economic terms such as return on investments and positive cash flow need to be considered. Below, we illustrate how the Rönnskär Smelter complies with these terms. To update the reader on current operations, our current flow sheet is depicted in Figure 1. The figure summarizes our current input and output."

Jan 1, 2012

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By Björn Lindquist

Boliden has developed a number of specialised technologies for smelter gas handling and effluent treatment. These technologies will be described. Special attention will be given to the high-pressure venturi, Editube wet electrostatic precipitator, mercury removal processes, and two-stage effluent treatment.

Jan 1, 2002

By T. Robyn

The Bolivar Cu-Zn skarn deposit in the Piedras Verdes mining district of Chihuahua is one of many base and precious metal deposits in the north-northwest trending Sierra Madre Belt extending across the states of Chihuahua, Durango and Sonora in northwestern Mexico. The information presented here is drawn from two papers on the Bolivar property1,4 plus new information. Historical mining and exploration for polymetallic Cu-Zn-Pb-Ag-Au deposits in the Sierra Madre Belt dates to Spanish Colonial days. Access to the Bolivar Property (Figure 1) is by paved road (approximately 305 km southwest from Chihuahua) and approximately 80 km by all-season gravel roads to the villages of Cieneguita (population ~1,000) and Piedras Verdes (population ~500) adjacent to the property. [ ] The Bolivar property comprises an old Cu-Zn producer (the Bolivar Mine), exploration concessions adjacent to the Bolivar Mine, and a new camp at the mine that supports mining, exploration and maintenance. From 1980 to 2000, former operators extracted approximately 300,000 tonnes of ore that was hand sorted to an average grade of 5-6% Cu and 25-30% Zn. From 2005-2010, Dia Bras produced from the mine just over 600,000 tonnes at an average grade of 1.7% Cu and 8.6% Zn. Dia Bras transported mineralized rock 275 km by truck and rail to its Malpaso mill, located about 30 km west of Cuauhtémoc in central Chihuahua, from 2005 until October 2011 when the new Piedras Verde mill was commissioned only 5 km from the mine. (Note: the Company cannot use the term ?ore? because it has never completed a feasibility study.)

Jan 1, 2012

Bolivia, due to its turbulent past with a history of constant military coups, has given an image of complete instability to the foreign investor. The effects of this have been several fold, the major one resulting in a complete lack of exploration in modern terms since their revolution in 1952. What was overlooked by the foreign investor was the fact that revolution produced Agrarian Reform which is the foundation of the stability which Bolivia enjoys today. Another factor that is overlooked is the fact that its past history is one of vast mining fortunes having being made. Their political problems resulted in economic chaos in 1985 with an annual inflation rate of 26,000 percent. This resulted in the collapse of the government but the democratic process continued. Then came the so-called"South American Miracle" in 1986 when the government of Dr. Paz Estenssoro enacted an extremely harsh austerity program which consisted of the abolition of wage and price controls, the abolition of monopolies, the right to hire and fire, the weekly auctions of dollars and the free convertibility of currency which yielded a stable government with 8 percent inflation. This was followed by massive personnel reductions in the various mines and other industries.

Jan 1, 1991

By Johnston, T. L.

BISMUTH is found as native metal associated with tin, copper, cobalt, silver, gold, or other metals and in a variety of ores. The more important ones are: bismuthinite (bismuth glance), Bi2S3; bismite (bismuth ochre), Bi2O3.3H2O; and bismutite (bismuth carbonate), Bi2O3CO3?H2O. Of lesser importance are the arsenate, telluride, and vanadate. The sulfide is the most common; the others are often oxidation products from this mineral. Bismuth minerals have been found in various places in the United States, principally in Colorado and Utah, but no ores are mined solely for bismuth. In the Granite mining district of Beaver County, Utah, a stratum of limestone about 6 ft. thick has been almost completely replaced by contact minerals in which bismuthinite associated with pyrite and molybdenite was found intergrown with silicate minerals. In the early days a few small lots of ore assaying 7 to 10 per cent bismuth were shipped from this district. Native bismuth has been found in the Clifton and Tintic districts of Utah. Bismuth is produced as a byproduct in the refining of lead, copper, gold and silver ores, it being recovered from the anode mud from the Betts process. Deposits of bismuth minerals exist in Argentina, Aus¬tralia, China, Japan, Germany, Spain, Peru, Bolivia, and Canada, but Bolivia is the principal, producer and could easily supply all of the present world's demand.

Jan 1, 1933

Load transfer capacity and failure mechanism of a fully grouted bolt installed across joints in shear is evaluated both experimentally and numerically in five types of bolts (low strength steel, rebar bolt and high strength steel). The strength of the concrete, bolt profile configuration, bolt mechanical properties and bolt pretension load play significant influence on the shear resistance, shear displacement and failure mechanism of the reinforced medium. Failure location moves towards the bolt joint intersection due to the increasing shear load, shear displacement and axial load developed along the bolt. Finally bolt failure occurs as a result of the induced axial and shear stresses acting between hinge points on either sides of the shear joint plane.

Jan 1, 2006

By Steve Bessinger, Steve Signer, James Pile

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining affected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied. This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

By Steve Signer

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining effected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

Jan 1, 2004

By Naj Aziz

Both bolt profile shape and spacing (rib spacing) have been found to influence the bonding capacity of the grouted rock bolt. The bolt surface profile configuration has greater importance to rock bolting in strata reinforcement in mining than the steel rebar used in civil engineering construction. This is because a rock bolt in mining usually is subjected to greater dynamic loading than the steel rebar in civil engineering construction. The increased bonding capacity of a bolt is important when supported ground is either heavily fractured, faulted or the supported ground is of soft formation, typically that of coal measure rocks. Past laboratory studies have identified the bolt profile spacing as of significant relevance to bolt resin rock bonding increase, however, no attempt has been made to determine the optimum spacing between the bolt profiles spacing. Accordingly, a series of laboratory tests were carried out on 22 mm core diameter bolts, commonly used in Australian mines, installed in cylindrical steel sleeve. The study was carried out using both push and pull testing methods. The push test was carried out in 150 mm long sleeves while the pull testing was conducted in 115 mm long sleeves. Profile spacing tested include, 12.5, 25.0, 37.5, and 50 mm lengths. Additional studies undertaken include modelling the profile of the load-displacement data of pull testing. Bolts with a profile spacing of 37.5 mm were found to provide optimum load bearing capacity as compared to other tested profile spacings.

Jan 1, 2009

A series of laboratory based push and pull tests were carried out to investigate how surface profile influence the load transfer mechanism of bolt/resin interface. Tests were carried out in both 75 mm and 150 mm long steel sleeves. Three types of bolts were examined, they were bolts most commonly used for strata reinforcements in underground coal mines in Australia. The bolts had near equal core diameter but of different profile configurations. The change in the length of the encapsulation sleeve was examined in light of the small number of profiles encapsulated effectively in short 75 mm long sleeves. The results showed that peak loads and displacements were directly related to the height and the spacing of the bolt surface profiles. Profile spacing appears to have greater influence on load transfer capacity than the profile height.

Jan 1, 2006

By Kikuo Matsui

Standing supports such as steel arches or square work supports along with the necessary struts and lagging have been traditionally employed in the longwall gateroads of the Japanese underground coal mines. Miike Colliery has newly introduced the interpanel-pillar mining system and the strata bolting system in gateroads to raise productivity levels and reduce operating costs. The Department of Mining Engineering, Kyushu University, in cooperation with the Miike Colliery and the Coal Mining Research Center, Japan (CMRCJ), has been conducting research into the optimum design of strata bolting as a primary support system in longwall gateroads. This paper presents a brief overview of the current state of strata bolting technique being applied in longwall gateroads at the Miike Colliery and discusses some problems in employing bolting.

Jan 1, 1993

By E. Stone, R. Reagan

Risk of hand injury is very real for operators carrying out conventional bolting operations with power torque tools, reaction arms and backup wrenches. Bolting operations of this type are common today in the installation and maintenance of heavy mining machinery and equipment. Newer solutions have become available that have the potential to dramatically reduce the risk of hand injuries in mining applications. MINING APPLICATIONS Within the scope of mining operations, various types of equipment are used such as tunnel boring machines, bucket wheel excavators, draglines, material handlers, screens, pumps, crushers, continuous miners and longwall systems. Design of these machines typically includes larger diameter bolts for strength and durability. Due to rugged use all machines require frequent maintenance and service which requires the use of heavy industrial bolting tools and methods. Those engaged in bolting operations include technicians working for end-users, equipment manufacturers, general contractors and others who provide services in mining operations. Most all personnel involved with these activities are engaged with use of high power bolting tools and procedures. Training is essential to raise the awareness of bolting safety and to avoid accidents. However improved bolting tools and procedures can play an even more significant role in further improving the safety of all those engaged with bolting in the mining industry. SAFETY CONCERNS Professionals working in the mining industry are constantly looking for ways to further reduce risk to health and safety. Bolting operations which are fundamental to service and maintenance of mining equipment are often overlooked as a potential area for improvement. Several areas of bolting operations offer potential for improvement in safety and avoiding accidents during equipment maintenance. This paper addresses the safety concerns associated with reaction arms and backup wrenches in conventional bolting applications (Figure 1).

Jan 1, 2019

By Compiled by Staff

"INTRODUCTIONThe U.S. Bureau of Mines (USBM) was established in the public interest to conclude inquiries and scientific and technologic investigations on mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increaseee efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the U.S. Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, USBM reports the findings of its research and investigations in its own series of publications and also in articles that: appear in scientific, technical, and trade journals; in "" proceedings of conventions and seminars; in' reference books; and in other non-USBM publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make this kind of list both necessary and valuable.This edition describes reports and articles published during calendar years 1992 and 1993. It supplements the 50-year list of Bureau publications from July 1, 1910, to January 1, 196O 2; and these 5- year lists of publications and articles: from January 1, 1965, to December 31, 1969 4, from January 1, 1970,to December 31, 19745 , from January 1, 1975, to December 31, 1979 6 , from January 1, 1980, to December 31, 1984 7 , and from January 1, 1985, to December 31, 1989 8."

Jan 1, 1994

By Rita D. Sylvester

"This compilation lists and summarizes publications by Bureau authors published in the regular Bureau of Mines series, in scientific, technical, or trade journals, or in other media; those available from the Bureau of Mines are indicated. Patents issued to Bureau personnel are also listed, and instructions are given on how to apply for permission to use them. One of the outstanding features of this Special Publication is an exhausive subject and author index. IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and present their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries, The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminar's; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1970, to December 31, 1974. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;3 and the 5-year lists of Bureau publications and articles from January I, 1960, to December 31, 1964,4 and from January I, 1965, to December 31, 1969.5 It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1970, to December 31, 1973."

Jan 1, 1975

By Rita D. Sylvester

"THE BUREAU OF MINES was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve mineral resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with that directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau sources. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented III this special publication both necessary and valuable. This issue describes Bureau reports and articles published during the period January 1, 1960 to December 31, 1964. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960,2 and the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960.3 It supersedes the annual lists of Bureau publications and articles from January 1 to December 31, 1960/ from January 1 to December 31, 1961,5 from January 1 to December 31, 1962,6 and from January 1 to December 31, 1963,1 The leading general and technical libraries of the United States maintain files of the Bureau's publications. A list of these libraries appears immediately following this introduction. BUREAU PUBLICATIONSBecause some series of Bureau reports contain both free and sales publications, and because the cost of sales publications varies, prices are indicated in the individual listings of all publications for which charges are made."

Jan 1, 1964