Search Documents

By K. Ohmori, K. Takeya, S. Yoshizawa, A. Kawamoto, T. Ishikawa

"High performance Sm2Fe17N3 magnet powder is developed nitriding Sm2Fe17 alloy that 'is made using a reduction and diffusion method. Typical remanence, coercivity and maximum energy product of the fine powder are 1.40 T, 1.13 T and 323 kJ/m3, respectively. Decreasing samarium content, oxygen content and the amount of a-Fe are found to be the important factors to realize high-energy product.High performance injection molded Sm2Fe17N3 anisotropic magnet is also developed using the powder and an original binder system developed in order to mold at low temperature. Typical remanence, coercivity and maximum energy product obtained are 0.77 T, 0.78 T and 103 kJ/m3, respectively in the density of 4.77 Mg/m3The temperature coefficient of remanence is -0.07 %/K and that of coercivity is -0.54.%/K. The initial irreversible flux loss of the magnet that has a permeance of two is -5 % at 100 °C and the irreversible .flux loss of it is -4.4 % exposing it at 80 °C for 1000h.IntroductionSm2Fe17N3 alloy powder is expected to be very useful for a bonded magnet. The reasons are as follows. The magnetization is as large as the Nd2Fe14B alloy. Curie temperature is even higher than the alloy. The uni-axial anisotropy is comparatively higher than the alloy. Consequently it is possible to obtain high coercivity after just milling the powder and therefore possible to obtain high-energy product in a bonded magnet as it is realized in the SmCo5 bonded magnet. On the other hand, sintering is difficult because it will be decomposed into samarium nitride and a-Fe when heating it up to 500°C:"

Jan 1, 2000

By Shaohua Ju

Siderite ore is abundant around the world, due to its inert properties of low grade, mudding when milling and low magnetic, and it is very hard to be beneficiated. Nowadays, decomposition by roasting becomes the main process for utilization of the siderite ore. The methods of energy input for roasting are normally electrical heating, coal or gas combustion. Because traditional roasting methods owns some disadvantiges, such as low energy utilization, high cost and/or large exhaust pollution, only about 10% of the siderite ores in China were used as iron concentrate. In this work, the possibility of roasting siderite ore with microwave energy is studied by both laboratory and pilot experiments. The result of laboratory experiments showed that the optimized condition is roasting for 20 min with a power density of 3 W/g, and the Fe content of the final sample obtained is about 59.12%. The pilot experiments result showed that the decomposition is thoroughly, and the main phases of the roasted material are magnetite and wustite, and the energy consumption of the roasting process is 695.8 KWh/t.

Jan 1, 2014

By B. G. Thomas

"Mathematical process models can be applied in several different ways to serve industry by inducing beneficial changes to process operation. This paper attempts to summarize the different uses, types, and attributes of these models, and to offer some ideas to consider when developing, using, and reporting on them. Process models range from empirical to mechanistic in nature and vary in complexity from simple analytical solutions to coupled, 3-D transient numerical simulations. They are classified here according to the way in which they are implemented in practice, viz. fully-online models, semi-online models, off-line models, and literature models. The purpose of the model should dictate how choices are made during its development. Ways to validate and compare the model with experiments are suggested. Examples are taken in the context of the author's experience in modeling the continuous casting of steel.IntroductionThe objective of this paper is to provide a partial introduction for this symposium by discussing some basic aspects of the application of mathematical process models in industry. Essentially, the aim is to explore how process models are used to benefit industry, and to offer some general comments and suggestions, based on the experience of the author, on how models can best meet this goal.This work is concerned with process models, which consist of systems of mathematical equations and constants that are solved on a computer to make quantitative predictions about some aspect(s) of the process. The specific variables required as input data and generated as output data are important features of the model. The equations often derive from a numerical solution to one or more differential equations and their boundary conditions. The model also includes the constants, which represent material properties, empirical relationships, and other knowledge about the process, and usually require considerable effort to obtain. Thus, general purpose commercial software packages, (ie. finite-element or finite-difference based codes), are not models in this context. They are useful tools, however, serving as frameworks for the development of process models."

Jan 1, 1994

By J. W. Holzenthaler

Teams continue to play a major role at the Phelps Dodge Mining Company El Paso Operations, especially during the present time of low copper prices. The El Paso Operations' teams have taken the initiative during this copper market downturn and have helped reduce operating costs significantly. Because of this, Phelps Dodge El Paso Operations has continued to grow within the team process by creating a total, non- exempt salaried workforce. In the last year alone, the El Paso Operations have implemented three major initiatives to accommodate the team process. The first was the creation of "guiding principles", a policies and procedures handbook. Second was the "zero and beyond" safety initiative. Third was team compensation. In addition, the Copper Products Company has now adopted a work-team environment, following the lead of the refinery.

Jan 1, 1999

By Jr. Napolitano, Jr. Sanders

"Morphological evolution of a dendritic growth front in a binary alloy is simulated using a cellular automaton approach to establish the feasibility of modeling such growth with a local rule-based scheme. The motivation for this work is derived from the need to predict the development of solidification structures within real components of complex geometry, where significant constraint of the thermal and solutal fields may exist. Such cases present complex boundaries and large domain sizes, which may preclude the effective use of more conventional methods. In this work, a model is presented which couples a two-dimensional alternate-direction-implicit finite-difference diffusion solution with a cellular automaton growth algorithm to simulate morphological evolution in alloys solidifying under directional growth conditions. Temperature, composition, and interface curvature are incorporated into a local growth potential which is used by the automaton, allowing the interface to evolve. Alloy solidification is simulated over a range of experimental conditions, producing various structures. Issues addressed include morphological instability, primary spacing selection, interface curvature, microsegregation, and tip conditions.IntroductionThe development of dendritic structure plays an essential role in alloy solidification. Virtually every microstructural feature, within a cast alloy component, is related to the interface morphology present during solidification. Conventional solidification theory, describing dendrite tip kinetics and mushy zone phenomena, provides a means for estimating overall microstructural parameters for an alloy solidified under steady-state conditions. Microstructural prediction for actual components, which are finite in size and complex in geometry, requires a description of the evolution of the interface morphology under transient conditions and geometrical constraint and an understanding of how the structure propagates through the mold. Any useful simulation tool must be equipped to handle these circumstances within the limits of computational feasibility."

Jan 1, 1998

By Joseph C. Milbourne

Tetra Technologies CCIX? (continuous countercurrent ion exchange) system has been involved in a wide range of uranium concentration, separation and purification applications over the past 40 years. Uranium ion exchange applications have ranged from the treatment of copper heap leach solution containing 5 parts per million of uranium to the treatment of high strength sulfuric acid solutions containing several thousand parts per million of uranium. The flexibility and the countercurrent mode of operation and other unique features of the CCIX? have resulted in successful uranium recovery from these solutions and many others.

Jan 1, 1995

By D. S. Barr

Mineralogical, lithological, and metallurgical studies were conducted on various gold ore deposits currently controlled by Freeport-McMoRan Gold Company. Ore samples were first lithologically and mineralogically categorized, then subjected to chlorination, roasting, and autoclaving pretreatments to determine their effects on gold recovery in a subsequent alkaline cyanide carbon-in-leach extraction. The studies indicate that, while organic carbon and sulfide sulfur are the primary refractory components, their effect on process response must be interpreted with respect to the deposit's geology and mineralogy. This approach has proven to be an effective method for evaluating metallurgical alternatives and fore-casting future mill performance.

Jan 1, 1987

By Go-Gi Lee, Jae-Young Jung, Myung-Duk Seo, Hyun-Na Bae, Seon-Hyo Kim

"Bubbles form at the anode during the electrowinning of magnesium and cause hydrodynamic acceleration and electrical field disturbance. A three-dimensional computational model was developed to investigate the effects of the geometry of the electrochemical chamber and the size distribution of bubbles on the fluid flow in the pilot plant. The results are validated by measurements of the surface characteristics of molten salt and the bubbles formed. Fluid flow at the surface was recorded with a high speed camera, and the distribution of bubble size is determined by inspecting the video images frame by frame. The measured size distribution of the bubbles is entered into the computer simulation of a multi-phase flow. A sloped roof is installed above the electrodes, to enhance the flow of the molten salt, thus resulting in higher current efficiency, lower energy consumption, and higher quality of magnesium metal.IntroductionTitanium's excellent properties of low density, high specific strength, high temperature strength, and exceptional resistance to corrosion are highly beneficial to diverse applications including aerospace, automotive, construction, and medical implants. Although the Kroll process[l] and Hunter process have been used for the extraction of titanium in the 20th century, their complicated engineering stages and high production cost, have led to further research into new processes such as FCC Cambridge, Armstrong and TiRO. Despite these intense research efforts, no process has yet been developed that is more economical than the Kroll process, by which most of the global commercial titanium is still being produced."

Jan 1, 2011

By Baohua Li, Yanhui Liu, Shengping Li, Xuewei Lv, Yun Chen

There are almost ten billion tons of vanadium-bearing titanomagnetite in Panzhihua-Xichang area. However, iron ores in Hongge, which has the most abundant reserves in the four mine areas in Panzhihua, have not been utilized sufficiently so far. The reason behind this is the relatively high Cr2O3 in the ores (0.49 %~0.82 %), that due to its high melting temperature will negatively influence the blast furnace reduction and slagging process. Therefore, in the blast furnace process, Cr is hope to be reduced into molten iron, which can reduce slag viscosity problems. Slag iron reduction experiments were conducted to quantify the Cr reduction. Experimental results shows that with the increase of TiO2, the content of Cr in the hot metal is decreased when balanced. And during the initial stage of the reduction reaction, the reaction kinetic model is a first-order reaction.

Jan 1, 2016

By Thomas F. Hagelien, Stein Tore Johansen, Svend Graadahl

"The dross appearing at the surface of an aluminium melt consists, in addition to aluminium, of mainly oxide films but also other non metallic inclusions. The inclusion particles are often poorly wetted by the metal and accumulate at the metal surface. However, in impeller stirred reactors for melt refining stirring may be exceedingly strong and inclusions accumulated at the metal surface may be entrained into the bulk metal. Concerning inclusion removal, such effects may deteriorate the effectiveness of melt refining.In this paper we investigate the surface entrainment of buoyant particles in a water model of an impeller stirred refining reactor. Under varying operating conditions the particle concentration in the bulk liquid is measured by laser light attenuation. The observed entrainment of particles is explained theoretically and metallurgical consequences of the findings are discussed.IntroductionIn the modern cast house continuos metal refining and casting is well established. One of the most distinct advances in metal refining has been the introduction of degassers which introduce bubbles into the metal. The bubbles act to remove dissolved elements together with nonmetallic inclusions. In the most efficient degassers stirring by different kind of rotors is applied to increase mass transfer and inclusion removal. However, it has been known from experience in the cast house that for violent stirring the concentration of some types of inclusions may increase from inlet to outlet of the reactor. This phenomenon has so far been attributed to production of dross in the reactor due to oxidation of metal. Due to removal of inclusions by bubbles the dross layer inside the reactor must be expected to increase in thickness by time. The removed inclusions and produced oxides due to strong stirring is removed at regular interval by the operators of the degasser. However, a fundamental understanding of the phenomena which take place in and below the dross layer is lacking. In the present work we add buoyant particles to the surface of a refining reactor and investigate how these particles may be entrained and dispersed into the liquid depending on the flow conditions. Similar investigations for gas stirred ladles have been performed by Taniguchi et al [1] who found that below a critical gas flow rate all particles are trapped at the surface. Above the critical gas flowrate the surface velocity are sufficiently high to entrain the particles. In this situation it looks like all particles are ready for the melt and a balance between terminal velocity and turbulent dispersion determine the concentration in the liquid."

Jan 1, 1999

By N. Kanari

The thermal decomposition studies of two zinc basic carbonate samples were carried out up to 400 "C by thermogravimetric analysis, boat experiments and differential scanning calorimetry measurements 'DSC'. The initial samples and the solid decomposition products were analyzed by scanning electron microscopy, x-ray diffraction and laser particle size analyzer. The thermal decomposition of both samples started at about 150 "C and the rate of decomposition became significant at temperatures higher than 200 "C. The apparent activation energies 'Ea' in the temperature range 150-240 "C for sample decomposition were between 132 and 153 kJ1mole depending on the sample origin. The XRD analyses of the intermediately decomposed samples and the DSC results up to 400 "C suggest that the decomposition reaction probably occur in a single step.

Jan 1, 2002

By Cecil Harriss

Philip Environmental Services Corporation's (Philip's) innovative fluidized bed thermal desorption system recovers mercury from contaminated soil. Referred to as the Thermal Recycling System, Philip has constructed a mobile thermal desorption system that has a processing rate up to five tons per hour. The system includes a continuous-feed system, all radiant heat, inert gas atmosphere, hot gas filter, two-stage cooling, and a water treatment system. Based on treatability studies, the processed soil can meet cleanup objectives as low as two milligrams per kilogram and passes the mercury toxicity characteristic leaching procedure test.

Jan 1, 1996

By K. J. Murphy, A. R. Smith, A. P. Odorski

"The need for large quantities of oxygen for use in metallurgical processes was a major driving force in the commercialization of tonnage air separation plants. Oxygen, nitrogen and argon impact the quality, energy efficiency and environmental aspects of metals production. Cryogenic air separation processes have been used to supply most industrial requirements, however, newer technologies are available or under development to meet the needs of today's and tomorrow's metallurgical processes. This paper reviews the technical features and state of development of adsorption, chemical, cryogenic and membrane technologies. The technologies are compared in terms of plant size, oxygen purity and pressure, nitrogen and argon co-production, product use pattern and back-up requirements. Computer control systems are described that optimize operation over varying load patterns and ambient conditions; substantially lowering energy consumption. IntroductionOxygen production totalled 390 billion cubic feet in 1987. Although current production is lower than the peak of 455 billion cubic feet reached in 1979, oxygen remains the fifth leading chemical product manufactured in the u.s. (1) Metals manufacturing and fabrication accounts for sixty percent of the oxygen consumed in the u.s. Oxygen use in the steel industry consists of air enrichment for conversion of iron ore, purification of the iron in basic oxygen or other furnaces, and for cutting and welding the finished steel product. Nonferrous ores are smelted in oxygen enriched atmospheres to reduce energy consumption and increase capture of sulfur compounds to meet environmental requirements. In the future oxygen usage is expected to become even more important in metals production as energy costs increase, environmental standards become more stringent, and as new coal based processes become commercialized. Oxygen usage per ton of metal in the new direct reduction processes can be up to ten times higher than traditional steel making."

Jan 1, 1988

By Jun Zhu, Jilai Xuel, Tao Li

"Coal gangue is industrial waste containing Al2O3 and SiO2 with great recycling and reuse values. This work is aimed at extracting Al2O3 content in the coal gangue by a process of carbonthermal reduction - alkaline leaching. The Al2O3 and SiO2 contents first became a mixture of SiC and Al2O3 in the process of carbonthermal reduction, and then Al2O3 was separated by leaching in NaOH solution, thus producing the sodium aluminate solution for Al(OH)3 precipitation. The products generated at various stages in the process were inspected using XRD and chemical analysis. The effects of parameters such as reduction temperature, carbon ratio, NaOH concentration, leaching time, leaching temperature, stirring speed, etc were investigated in details.IntroductionCoal gangue is an industrial residue resulted from the process of coal mining and washing, accounting for 100 - 150 kg with 1 ton raw coal mined. The existence of coal gangue in large quantities has become a serious problem for environment pollution. On the other hand, the chemical compositions of coal gangue are Si02 and Ah03 primarily. In China, the accumulation storage capacity of Ah03 in coal gangue is not less than 600 million ton at a rough estimate, which should be considered as an abundant second resource [1]. If the alumina can be recycling and reused effectively from coal gangue, it will not only reduce the imperilments caused by coal gangue, but also yield good economic returns.Generally, the processes of extracting Al2O3 from coal gangue can be divided into acid leaching (vitriol or hydrochloric acid) and alkaline leaching (mostly NaOH) [2]. The acid leaching processes have many problems, such as lower leaching ratio, corroding the equipments, recycling the spent acid hardly, etc. The primary matter of alkaline leaching process is silica dissolving with alumina, which brings perplexing desilication process, alumina loss seriously and higher energy consumption."

Jan 1, 2011

By Neeraj Saxena, Madhu Huggahalli, Jerry Bednarski, Ken Grieshaber, David Stoffel

"The use of oxy-fuel burners in secondary aluminum melting applications offers several advantages over air-fuel burners including reduced fuel consumption, faster charge to tap times and lower NOx emissions. Their successful, safe and economical use in a furnace depends on several factors and considerations such as burner and flue placement, metal circulation, charge practices and the type of refractory used in the furnace.These factors required in the successful conversion of furnaces from air-fuel to oxy-fuel based burners are discussed in this paper. Critical parameters are identified and examined using computational fluid dynamics (CFD) simulations. Parameters are estimated via laboratory testing and validated through trials performed at commercial installations. Guidelines and a simplified approach to estimate a priori the economic impact of converting from air-fuel to oxy-fuel are presentedThe final products of this research are simplified and validated tools for modeling aluminum furnaces. These include improved heat and energy balance models and parameterized CFD solutions which provide rapid customization to individual furnace configurations. These tools provide field engineers with immediate and accurate predictions of performance, allowing for repeated precise scenario analyses."

Jan 1, 2001

By Metehan Erdogan, Furkan Özdemir, Ishak Karakaya, Mustafa Elmadaglı

Tungsten is mainly produced by H2 reduction of WO3 which makes its production difficult and costly. A promising method was recently reported for direct electrochemical production of tungsten from CaWO4 (scheelite) which is estimated as the seventy percent of the all tungsten reserves of the world. This paper investigates the application of pulse current in the electrochemical reduction of CaWO4 pellets attached to a current collector. The electrolyte was composed of calcium chloride and sodium chloride salts at eutectic composition (48 pct mol NaCl at 873 K). The reduced samples were cleaned with dilute hydrochloric acid solutions and characterized by X-ray diffraction and scanning electron microscopy. Examination of the results revealed that metallic tungsten was obtained by pulse current reduction.

Jan 1, 2016

By A. G. Cecutti

A brief overview of the known significant health effects of both Nickel and Cobalt will be presented. Some time will be given to the current research activities, especially for Nickel. Emphasis will be placed on some of the controversial issues associated with their health effects.

Jan 1, 1988

By Tracie Zoeller, G. Paul Neitzel, Jr. Sanders

"As-cast aluminum alloy microstructures are highly segregated. Coring occurs when solute is rejected during solidification resulting in a non-uniform solute distribution across the dendrite arms. Furthermore, coarse constituent phases are formed in the interdendritic channels as a result of coring. These constituents are either soluble or insoluble and can form from the major solute elements, or the impurity elements iron and silicon. The dissolution of these constituents, or precipitates, is an important consideration in determining the microstructural evolution of an alloy. The properties of an alloy are significantly affected by the morphology of the precipitates. Precipitates can be either beneficial or detrimental to the properties of the alloy. Regardless of the nature of the precipitates present, it is useful to understand the dissolution process. A diffusion-limited dissolution model for planar precipitates is presented and compared to an analytical solution and to models in the literature. Experimental data for the dissolution of AhCu precipitates in a dilute alloy are compared to the proposed model, and found to have good agreement.IntroductionDuring the processing of precipitation hardening alloys, beginning with the solidification step and ending with the final solution heat treatment step, there are a variety of particles that form. Some of these particles must be dissolved and solute redistributed and re-precipitated in a more homogeneous distribution than as it first appears in the as-cast microstructure. The particles can be classified by size as microstructure develops during processing. Coarse particles that form during solidification can either be soluble, partially soluble or insoluble. These particles can be the result of coring of the major solute elements as well as the limited solubility of elements such as iron and silicon. Iron and silicon can combine with the major solute elements such as copper in 2xxx alloys forming coarse phases often referred to as constituents. Figure l(a) shows the as cast microstructure with the constituent phases, Al2Cu and the insoluble phases containing Al-Fe-Mn-Cu-Si [7]. During preheating the soluble phases such as AhCu that were formed by eutectic decomposition must be taken back into solution, whereas the insoluble phases remain essentially unchanged by most thermal operations. Figure l(b) and (c) show some of these constituents after subsequent preheating steps. In Figure l(b), AhCu platelets are shown and in Figure l(c) the remnants of the AhCu phase are noticeable, along with Mn-bearing dispersoid phases. Reduction in the volume fraction and size of these phases improves the ductility and fracture toughness as well as reducing the inhomogeneities that occur during coring. Also adjacent to the dendrite arm boundaries are smaller AhCu phases that precipitate by a solid-state transformation on cooling to room temperature."

Jan 1, 2004

By S. L. Pohlman

Physical characteristics of possible importance in the acid leaching of Chrysocolla have been evaluated. Surface area studies and pore size distribution indicate: 1) a large surface area (350 m /gm); 2) an average pore size of 13 or 16 Å , depending upon use of the adsorption, or desorption, branch of the Type IV isotherm in the evaluation; ) the presence of a significant fraction of pores of size less than 15 Å determined by the accumulation surface area method. The initial structure is micro- crystalline on the basis of x-ray powder patterns; the silica leach residue is amorphous and has only 24 m2 /gm surface area, and loses integrity when dry. However, readsorption of copper onto the wet leach residue gives a product with integrity and 100 m2 /gm surface area. Visual observation of the leach residues supports evidence of a non-protective diffusion mechanism of leaching which is well correlated by the shrinking core model previously presented.

Jan 1, 1976

By Bo Yan, Jiaquan Zhang, Haibo Sun

"Based on the validation of steady-state isothermal mathematical model by a 0.4-scale water model for the single-strand slab casting tundish, the effect of varying pouring temperature on the flow, temperature field, and residence time distribution(RTD) of the liquid steel was studied by a transient hydrodynamic model. Due to the decreasing temperature of ladle stream over a casting period of 50 min, the direction of vortex flow at the downstream side of dam changes to clockwise from the anticlockwise at 4 min after the new teeming, and reverts to anticlockwise direction again at 43 min. Meanwhile, the melt flow state in the dam hole is also varying with time. For conventional isothermal water modeling, the RTD parameters obtained are much different as compared with the non-isothermal ones. For the flow control devices(FCD) design, however, the identical optimal scheme can be concluded from the point of view of isothermal modeling.IntroductionOriginally, tundish was adopted as a buffer and distributor to hold and allocate molten steel for sequence casting upon ladle exchange and to provide a desired steel flow rate to the mould below. With the increasing demand to strand quality, the tundish has become a critical metallurgical reactor to enhance inclusions removal, avoid reoxidation of molten steel, and prevent slag entrapment. The general trends to obtain these metallurgical effects are to optimize steel flow pattern and to extend the residence time of molten steel in the tundish through increasing the volume of tundish and/or using FCDs in the interior of the tundish."

Jan 1, 2012