Search Documents

By W. G. Davenport

A survey of world copper refining tankhouse .practices has been carried out. This paper compiles the results and examines changes in operating practices .since the similar 1987, 1991 and 1995 surveys. Continuing trends are the installation of ISA Process and Kidd Process stainless steel cathode technology, polymer concrete cells, anode preparation machines and automatic cranes. Instrumentation and automatic control are increasing, particularly for addition agent optimization; solvent extraction .and ion exchange techniques are being increasingly applied for electrolyte purification. The overall consequences of these changes have been 'improved cathode purities and enhanced tankhouse productivities.

Jan 1, 1999

By R. L. Player

"The Copper Isasmelt process has been developed over the past 15 years by Mount Isa Mines Limited (MIM) and the Commonwealth Scientific and Industrial Research Organisation (CSIRO). The first two commercial plants were commissioned in mid 1992.The results of four heat balances on the Mount Isa plant are presented. At a smelting rate of 98 t/hr of chalcopyrite concentrate plus 14 t/hr reverts, the total heat generated was -91MW. Approximately 39% of this energy came from coal, while 50% of the energy reported to the process waste gas. To a first approximation the furnace is near chemical equilibrium.The impurity distribution in the Mount Isa plant was presented. Approximately 91 % As, 85% Cd, 75% Bi, 68% Zn, 60% Sb and Tl, 45% Pb and 30% Te in concentrate was eliminated from the matte.The ""bubble"" frequency of the gas cavity below the foot of the lance was measured at -2. 1Hz. Side bands displaced by -l.lHz modulated the bubble frequency. This was consistent with radial gravity wave motion in the slag bath. The two processes, gas bubbling and wave motion appeared to be coupled together; the bubble frequency was twice the slop wave frequency. IntroductionCopper Isasmelt has been developed over the past 15 years by Mount Isa Mines Limited and the Commonwealth Scientific and Industrial Research Organisation. The process is based on the Sirosmelt lance, invented by researchers at the then Division of Mineral"" and ProcessEngineering ofCSIRO in 1973.The first two commercial scale copper furnaces were commissioned at Mount Isa and the Cyprus Miami Mining Corporation smelter at Miami, Arizona in August and June 1992 respectively.The process concept, the history of the development, and the Mount Isa plant have been described (1, 2, 3).This paper sununarises heat balances obtained on the furnace, the impurity distribution among the output streams and lance injection characteristics."

Jan 1, 1996

By David Hughes

The paper covers the utilization of on-line analysis in process control of solvent extraction in nickel leach solvent extraction processes in Finland and Australia and in copper heap-leach and solvent extraction in Chile. The goals of and requirements for controlling the solvent extraction stages of the processes are reviewed. The applications at three plants are compared. The development of the technology used is reviewed and design considerations are discussed. Requirements for on-line control and analyzer performance are compared. A new generation of analyzers and its effect on the set-up process of a project is introduced.

Jan 1, 2003

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to 107 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By A. F. Giamei, F. Landis, M. O. Duffy, R. J. Mador

"The directional solidification of complex advanced gas turbine airfoils must be carried out without the nucleation of undesirable grains and with minimal shrinkage. Such problems are typically eliminated by using a number of mold design and process iterations. A more efficient approach is envisioned where a solidification model is generated and utilized to accelerate process development. Towards this end, the directional solidification (DS) of simple geometrical shapes in a crystal grower apparatus has been simulated with MARC finite element nonlinear thermal analyses.The finite element models of cylindrical (2D) and rectangular (3D) cross-section bars in the DS environment are presented. Temperature dependent properties, the impact of latent heat of fusion and a time-dependent radiation boundary condition constitute the more salient features of the MARC models. Solidification zone thermal behavior is predicted during the withdrawal transient for the specific case of nickel based superalloys grown in ceramic shell molds. Comparisons of analytical results with experiments demonstrate notable prediction accuracy. INTRODUCTIONSingle crystal and uni-directional crystal turbine blades require tightly controlled conditions if metallurgically and mechanically acceptable parts are to be produced. Gated blade geometry and process parameters must be precisely determined if incorrect grain structure, orientation and shrinkage are to be avoided. Since purely experimental development programs designed to evaluate these parameters can be excessively costly and time-consuming, an effort combining engineering analysis and verification by experiment has been initiated at Pratt & Whitney. Comparison of analytical predictions and measured data for geometries simpler than a turbine blade, namely cylindrical and rectangular bars, comprised the initial stage of this effort. Subsequent tasks involve modeling geometries of increasing complexity and ultimately the simulation of the directional solidification of the turbine blade, shown schematically in Figure 1. This paper summarizes the results of the initial stage of the effort."

Jan 1, 1986

By N. A. Warner

Fundamental studies on the reaction of limestone or dolomite at high temperature with S02 are extended to the realm of large scale primary copper smelting. Whereas flue gas desulfurisation in the electric power utility industry is concerned with S02 concentrations normally less than 0.5 percent, high temperature smelting gases can have S02 levels approaching 100 percent. The reaction involved is very exothermic so proposals are made in this paper for returning the heat generated in sulfur fixation directly back to the copper smelting process. This integration leads to metal production with lower energy requirements than current technology. The anhydrite reaction product can either be disposed of locally with minimum adverse environmental impact or upgraded to a value-added product. It is assumed, of course, that no viable market exists to support sulfuric acid production.

Jan 1, 1996

By Kenichi Moriyama

The Sumitomo Toyo Copper Smelter started operation in 1971, as an epoch-making smelter at which 9996 of the charged sulfur could be captured. In the past ten years, the amount of treated copper concentrate has-been increased from 1,300 l/ day to 1;900 t/ day by the extremely effective application of the oxygen enrichment for a flash smelting furnace and converter furnace. The sulfuric acid production capacity at the acid plant has also been increased up to 1,900 t/ day corresponding to the increase of copper concentrate smelting rate without installing an additional acid plant. Furthermore the sulfur fixed ratio is kept at a high level, more than 99.996. despite the SO. strength fluctuation of the wide range of 596 to 1396 which is attributed to the combination of flash smelting furnace and, P.S. converter. These -operational results at the? acid plant were achieved by several modifications. and two examples are briefly described as follows; (1) Converter modifications in order to cope with the high SO, strength -gas (2) Introduction of the anodically protection shell and tube type acid coolers In addition. the quality of sulfuric acid has been positively increased. For example, the concentration of iron and arsenic, which were the main Impurities in ?sulfuric acid, was successfully .reduced.

Jan 1, 1995

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By S. Street

The Environment process, invented by Prof. H.K.Womer and developed at the University of Wollongong, simultaneously treats ferruginous and organic wastes via bath smelting. Conceived in the late 1980's, the patented process was originally developed using steelworks dust to settle solids from sewage, producing a composite material suitable for smelt reduction. Work began on the process in 1990 with the Australian patent having a priority date of February 1990. Early research focussed on settling of solids from sewage, while pyrometallurgical investigations examined smelting in small induction furnaces. By 1992 smelting trials had been undertaken in pneumatic and electric arc furnaces, the process being successfully demonstrated up to on 8 tonne scale. The success of this particular trial, and other smaller trials, resulted in construction of a 100kg DC arc furnace which was commissioned in 1993. By 1994 the main project focus was on development of the smelting technology. Over 3 years of trials on the DC arc furnace have identified and clarified many of the pyrometallurgical reactions. optimum operating parameters, as well as demonstrating the versatility of the process for treating a wide range of wastes. Currently the Illawarra Technology Corporation (lTC), the commercial arm of the University of Wollongong, is pursuing commercialisation of the process.

Jan 1, 1996

By L. M. Abrantes, A. P. Paiva

"A brief review of some innovative methods for the direct recovery of metals from loaded organic phases is presented; emphasis is given to electroreductive stripping and cementation, which are described and illustrated by examples: of current research. The recovery of silver using a two-phase electrolysis - by direct application of an electrical potential to a mixture of a metal loaded organic phase· containing Cyanex 471X, obtained by solvent extraction, and a stabilized sodium thiosulfate solution - is more extensively discussed. The overall efficiencies are analyzed and compared with data obtained by conventional stripping procedures. Some preliminary results achieved for the recovery of the precious metal using galvanic stripping, applied directly to similar organic solutions and involving zinc and iron powders as reducing agents, are also evaluated.Introductory ReviewThe application of hydrometallurgical methods to the recovery of metal values from ores and concentrates has been receiving a growing interest, either from researchers or from the mining industry [1].For the concentration / purification of the relatively low concentrated metallic solutions resulting from the leaching of those raw materials, solvent extraction (SX) is a well established technique [2]; the loaded organic solvent is then conventionally contacted with a suitable aqueous solution, the metal in its final form being usually recovered from this solution by electrowinning.As an efficient and / or selective stripping is sometimes difficult to achieve, depending on the specific characteristics of the system under consideration, some alternative procedures have been analyzed in order to overcome this problem. One of the chosen routes, mainly developed by Hirai and Komasawa, is to promote the reduction of the desired metal species in the organic phase, in such a way that the stripping stage becomes feasible; for the selective stripping of vanadium from a solvent containing a mixture of vanadium and molybdenum, the authors successfully used reductive [3], electro-reductive [4,5] and photo-reductive [6] techniques. The two latter methodologies have also been applied to the recovery of europium from a solvent containing europium, samarium and gadolinium [7,8].However, further processing is necessary to recover the metal in its solid state; therefore, methods causing the direct reduction of the metal species in the organic phase to their fmal metallic form would be of interest, as an intermediate step would be avoided"

Jan 1, 1997

By Sebastião Ribeiro, Leonardo Carneiro Sardinha, Alline Sardinha Cordeiro Morais, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

The glass tube of spent fluorescent lamps is contaminated with mercury, which might be a serious hazard in the case of conventional recycling by melting with other glasses. A possible solution could be its incorporation into a clay body to fabricate common fired ceramics such as bricks and tiles. The objective of this work is to characterize a type of fluorescent lamp glass waste to be incorporated into a clayey ceramic. The characterization was performed in terms of wettability tests to evaluate the interaction between the surface of the clayey ceramic and glass waste as a function of the firing temperature. The results showed that the contact angle decreased with increasing temperature, reaching a value of 79°, at a temperature of 1100°C, but not sufficient to completely wet the ceramic. However, compatible chemical composition and reduction of porosity by the flow of soft glass waste between the clay particles favor the consolidation of the ceramics structure above 900°C.

Jan 1, 2015

By Shinroku Matsuzaki

Data the measurement sensor installed with spatial distribution on the blast furnace were successively accumulated online from the process computer to the database system over a long period. This is a new system that accurately considers the relation with the installation position of each sensor, and picture computerization of the measurement data was developed. The overall operation state of a blast furnace, which skilled operators can see in their mind?s eye, was objectively visualized as pictorial information.

Jan 1, 2006

By Akira Nishikawa

During the twentieth century, the copper smelting industry achieved dramatic expansion corresponding to the vast growth of global economy. This was largely due to innovations in pyro-metallurgical processes, such as autogenous smelting and continuous smelting and converting technologies. However, as copper production capacity increased, its impact on the environment also could not be ignored, and thus with increasing global environmental awareness, many smelting operations either had to renew or rebuild their facilities. In addition to these changes, in places like Japan and Europe, with scarce primary resources, the treatment and recovery of metals from a variety of items such as car shredder dust, used electrical appliances and electronic devices, on top of scraps traditionally treated, is having a profound effect on the reduction of waste and the preservation of primary resources. Thus compared to the days when copper smelting focused on the environmental control in order to break with "Smoke Stack Industry", copper smelting today is making an important contribution to the sustainable development of human society.

Jan 1, 2003

By Akira Nishikawa

During the twentieth century the copper smelting industry achieved dramatic expansion corresponding to the vast growth of global economy. This was largely due to innovations in pyro-metallurgical processes, such as autogenous smelting and continuous smelting and converting technologies. However, as copper production capacity increased, its impact on the environment also could not be ignored, and thus with increasing global environmental awareness, many smelting operations either had to renew or rebuild their facilities. In addition to these changes, in places like Japan and Europe, with scarce primary resources, the treatment and recovery of metals from a variety of items such as car shredder dust, used electrical appliances and electronic devices, on top of scraps traditionally treated, is having a profound effect on the reduction of waste and the preservation of primary resources. Thus compared to the days when copper smelting focused on the environmental control in order to break with "Smoke Stack Industry", copper smelting today is making an important contribution to the sustainable development of human society.

Jan 1, 2003

By G. G. Richards

The zinc slag fuming process is used to recover zinc from molten iron-calcium silicate slags by treatment with pulverized coal and air. The rate of zinc fuming is controlled by the complex interaction of several kinetic factors including the rate of entrainment of coal in the slag, the extent of the coal-slag reaction and the rate of ferrous oxide oxidation to ferric oxide. This paper briefly outlines the mechanism of fuming and, on this basis, optimization of process parameters is discussed. Modelling analysis and recent industrial trials at Cominco show that coal entrainment in the slag, bath temperature, and bath depth are critical variables affecting process rate and efficiency. The first step in process optimization is to assess coal bypass of the bath. In general, changes which promote operation at a higher temperature, greater coal entrainment in the slag and extended residence time of the coal in the bath increase fuming performance. Coal entrainment is controlled by injection conditions whereas bath temperature is a function of coal combustion and ferrous oxide oxidation. Residence time of the coal is largely a function of bath depth. The implication of model predictions for continuous fuming is shown.

Jan 1, 1994

By S-L. Jämsä-Jounela

Fault diagnosis systems have attracted growing interest in a number of engineering fields. The number of applications has increased and successful results have been widely reported. The fault diagnosis system presented in this paper is integrated, and it monitors the states of the process and performs fault detection and diagnosis on the process equipment. The monitoring of process states is carried out by means of Kohonen Self-Organising Maps that is a powerful tool in visualisation and analysis of high dimensional data in engineering applications. This paper presents the results of SOM analysis carried out on the Outokumpu flash smelting process. The subsystems analyzed in more detail are the condition of the concentrate burner, the condition of the gas line on the basis of the pressure distribution in the process and the cooling water circulation of the waste heat boiler, and the condition of the furnace and furnace equipment on the basis of the temperature distribution in the furnace and gas line. Keywords: Fault diagnosis, Process monitoring, Kohonen Self-Organising Maps, flash smelting

Jan 1, 2001

By V. V. Satya Prasad, A. Sambasiva Rao

Electroslag melting technologies have recently been developed for recycling light scrap of valuable metals and alloys such as superalloys and oxygen free high conductivity (OFHC) copper at Defence Metallurgical Research Laboratory (DMRL), Hyderabad. Conventionally, electroslag melting processes use consumable electrodes. Because of the difficulty in compaction of scrap into a consumable electrode of satisfactory quality, non-consumable electrodes such as graphite and water-cooled copper have been designed. Electroslag remelting using a water-cooled non-consumable electrode was developed to melt scrap of a nickel base superalloy. Sound ingots with smooth surface finish and properties comparable to vacuum melted superalloys could. be obtained from scrap using this process. A modified electroslag crucible melting process using graphite crucible and graphite electrode was developed for recycling OFHC copper scrap. Copper ingots with less than 10 ppm oxygen and electrical conductivity"" 100% IACS could be produced. The same process was also utilized to produce copper-based alloys such as copper-chromium and copper-titanium starting from copper scrap.

Jan 1, 2000

By D. J. Webb, D. G. Reynolds, D. W. Ashman, D. W. Goosen

Cominco Limited operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Central to the successful operation of this complex is the treatment of zinc leach residues through the lead smelter. In 1997, Cominco started up a new lead smelter using KTVCET flash smelting, a state-of-the-art conventional slag fuming furnace, and a new drossing plant. The smelter has fully met the requirements for environmental performance, reduced energy consumption, and lowered labour costs. This paper provides a description of the new smelter and discusses the problems encountered during the start-up, as well as the solutions to those problems. Recent operating results are presented. Lead-Zinc

Jan 1, 2000

By Y. Ikeda

Typical electric appliances were dismantled into component pieces to study the recyclability of these discarded goods. Types and weight ratios of these component materials were investigated and characterized. The results showed that if they are dismantled properly, these goods could be classified into several groups of similar materials and/or structures, namely those consisting of single materials, metal-plastic combinations, metal-metal combinations and complex combinations of many different materials. By separating each combination into recyclable materials and isolating hazardous materials, it was found that the final waste for disposal could be reduced and the recycling efficiency could be improved markedly as compared to the conventional shredding method. The metal-metal combinations account for 60% by weight of the total metal contents in electric appliances, and therefore, it becomes important to segregate these metals. For the complex combinations, a process consisting of pyrolytic decomposition of plastic contaminants followed by smelting of the residue is proposed. It is anticipated that nearly zero-emission recycling of electric appliances will be achieved by applying this treatment process.

Jan 1, 1995

By N. Kanari

Reactivity of MgO towards C12+air, C12+N2 and C12+CO gas mixtures was studied up to 1000 °C. Carbochlorination of MgO occurs at temperatures lower than that of its oxychlorination. Effects of gas flow rate, temperature and partial pressure of the carbochlorinating gas mixture on the reaction rate were investigated. The apparent activation energy of MgO carbochlorination is 49 kJ1 mol between 425°C and 600°C. At 550 °C, the apparent reaction orders with respect to C12+CO, C12 and CO, are 2.37, 1.47 and 0.89, respectively. At this temperature, the maximum reaction rate was obtained using a C12+CO gas mixture having a Cl2lCO molar ratio equal to about 0.6.

Jan 1, 1998