Search Documents

By Rob G. Jeffrey, Ken W. Mills, Jesse W. Puller

"A coal mine in New South Wales is longwall mining 300m wide panels at a depth of 160-180m directly below a 16-20 m thick conglomerate strata. As part of a strategy to use hydraulic fracturing to manage potential windblast and periodic caving hazards associated with this conglomerate strata, the in situ stresses in the conglomerate were measured using ANZI strain cells and the overcoring method of stress relief. Changes in stress associated with abutment loading and placement of hydraulic fractures were also measured using ANZI strain cells installed from the surface and from underground. This paper presents the results of in situ stress measurements and stress change monitoring undertaken as part of the hydraulic fracturing program.Overcore stress measurements have indicated the vertical stress is the lowest principal stress so that hydraulic fractures placed ahead of mining form horizontally and so provide effective pre-conditioning to promote caving of the conglomerate strata. Monitoring of the full-scale hydraulic fractures has confirmed the hydraulic fractures grow horizontally.Stress changes monitored during hydraulic fracturing formed part of a broader program to investigate fracture geometry and growth rates to confirm the characteristics of the hydraulic fractures placed. This monitoring showed that vertical stress in the conglomerate strata was being increased by up to 1 MPa in close proximity to the hydraulic fracture and had the effect of tending to promote asymmetrical growth of subsequent fractures about the injection borehole.Monitoring of stress changes in the overburden strata during longwall retreat was undertaken at two different locations at the mine. The monitoring indicated stress changes were evident 150 m ahead of the longwall face and abutment loading reached a maximum increase of about 7.5 MPa. The stresses ahead of mining change gradually with distance to the approaching longwall and in a direction consistent with the horizontal in situ stresses. There was no evidence in the stress change monitoring results to indicate significant cyclical forward abutment loading ahead of the face consistent with the observations of face conditions underground adjacent to both measurement locations. The forward abutment load determined from the stress change monitoring is consistent with the weight of overburden strata overhanging the goaf indicated by subsidence monitoring."

Jan 1, 2015

By Fangting Dong

The broken rock zone (BRZ) and the tunnel support theory are investigated. The relationship between the BRZ and the related factors, the interaction between the BRZ and supports, and the function of supports are analyzed in detail based on the authors' underground observations and model taste. A summary of the application of the BRZ theory in the past is also presented.

Jan 1, 1988

By Thomas M. Barczak

Wood cribs have been the dominant form of supplemental support in coal mining for many years. Recently, there has been a renewed interest in prop supports as a replacement for wood cribbing due to the increasing cost of mine timber and engineering advancements in prop design to improve their stability and yield capability. Prop supports generally consume less material, can be installed in less time with less labor, and provide less restriction to mine ventilation than wood crib supports. Several prop supports are now available or under development'. These include: (1) Strata Products Propsetter? Support System; (2) Heintzmann ACS and Super Prop; (3) MBK-Hydraulik MEGA prop; (4) Advanced Mining Technology Inc. (AMTI) BTS Mortar prop; (5) Dywidag Coal Post; (6) Western Support Systems YIPPI support; and (7) "The Can" support by Burrell Mining Products. A comparison of the performance and cost of these support systems to wood cribs is made to provide mine operators with information needed to assess their application potential. Examples of current underground installations are discussed. Included in this assessment are full scale tests of these supports conducted in the U.S. Bureau of Mines' Mine Roof Simulator.

Jan 1, 1995

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By Timothy Batchler

"Standing roof supports help to provide a stable working environment in coal mine gateroads. NIOSH participates in the development of these support systems by conducting full-scale tests in their Mine Roof Simulator. These tests have established the performance characteristics of every coal mine support system currently in use in the United States. Through these tests, mine operators and regulatory officials have acquired a fundamental understanding of the various types of support performance that guides the assessment and use of these support systems. However, some little known factors that influence support behavior can lead to misconceptions and, perhaps, a poor assessment of support behavior at times. This paper highlights several of these factors and discusses their significance. The paper also examines a current longwall tailgate support and discusses the inefficiency with this approach. Finally, the NIOSH Mine Roof Simulator (MRS) is the world’s most powerful load frame built specifically to test full-scale roof supports, including longwall shields. are addressed in this paper to provide a more in-depth assessment of the limitations of the MRS and what the MRS testing protocol is designed to do. INTRODUCTION Over the years, considerable research has been conducted to develop standing support technologies and to evaluate their performance characteristics. The load and displacement characteristics of the standing supports have been determined from full-scale testing conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) (Barczak and Tadolini, 2008) located in Bruceton, PA. Performance traits, installation patterns, and ground responses are observed in various geological and mining conditions and are evaluated to determine the support performance in the field (Dolinar, 2010; Campoli, 2015; Zhang et al., 2012). Despite widespread use of standing supports, not every aspect of their performance and resulting ground support capability are always well understood. This paper discusses 10 factors, several of which are surprising, that impact standing support performance."

Jan 1, 2017

By Elia Elias, Alan Crosky, Paul Hagan, Damon Vandermaat, Serkan Saydam, Peter H. Craig

"The University of New South Wales (UNSW Australia) had been involved in the study of premature failure of rock bolts in Australian coal mines from the initial identification of the problem in 1999 (Crosky et al 2002). Rock bolt steel changes over the last decade appear to have not reduced the incidence of failures. A broadened UNSW research project funded by the Australian Research Council (ARC) and Industry has targeted finding the environmental causes through extensive field and laboratory experiments. This paper describes the field studies conducted in underground coal mines, in particular attempts to measure the contribution to corrosion from groundwater, mineralogy and microbial activity. Various underground survey techniques were used to determine the extent of broken bolts, with the presence of both stress corrosion cracking (SCC) and localized deep pitting making no single technique suitable on their own. Groundwater found dripping from bolts across various coalfields in Australia were found to be not aggressive and known groundwater corrosivity classification systems did not correlate to where broken bolts were found. In-hole coupon bolts placed in roof strata containing claystone bands confirmed the clay as being a major contributor to corrosion. Microbes capable of contributing to steel corrosion were found to be present in groundwater, and culturing of the microbes taken from in-situ coupon bolts proved that the bacteria was present on the bolt surface. An ‘in-hole bolt corrosion coupon’ development by the project may have multiple benefits of 1) helping quantify newly developed corrosivity classification systems, 2) providing an in-situ ground support corrosion monitoring tool, and 3) for testing possible corrosion protection solutions.introductionThe problem of premature rock bolt failure in Australian coal mines was published in 2002 and 2004 by UNSW Australia from Australian Coal Association Research Program (ACARP) funded projects. The majority of the broken bolts examined had steel Charpy impact toughness values of 4 – 7 Joules, and the failure mechanism was most often stress corrosion cracking (SCC). Steel fracture mechanics predicts that an increase in impact toughness will increase the length of the crack before sudden brittle failure. In the final report of 2004, anecdotal evidence from one coal mine indicated that the problem may be eliminated in some environments by a change to steel grades with higher Charpy impact values of ~16. (Crosky et al, 2002 and 2004)"

Jan 1, 2015

By Morgan M. Sears, Gamal Rashed, Jim Winfield, Brent Slaker

"Over the past decade, ground falls have resulted in five fatalities, representing over 40% of all fatalities occurring in underground stone mines in the United States. In conjunction with recent high-profile pillar collapses, the need for further ground control research in the nation’s stone mines is evident. Ground conditions are growing more difficult. Therefore, this research is focused on deep cover, steeply dipping, and multi-level underground nonmetal mines. The objective of this paper is to introduce a geomechanical study of pillar development in a steeply dipping limestone deposit. To accomplish this, a numerical model was developed using input from modified laboratory test data and in situ stress measurements provided by the mine to simulate the development of a pillar under these conditions. The model was then verified against field observations and stress mapping. The calibrated model was then used to calculate the estimated stresses in the pillar and immediate roof as development progresses around an instrumented pillar.INTRODUCTIONGround falls represent a significant hazard in the nation’s underground stone mines. In response to recent large-scale pillar collapses, as well as stakeholder interactions, researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at mines operating in challenging operational environments. These include deep-cover, steeply dipping, and multi-level mines where there is the potential for an increased risk of ground failure. The Pleasant Gap Mine, shown in Figure 1, operates in the Valentine Formation, which is typically light grey, extremely fine-grained limestone, and approximately 21.3 m (70 ft.) thick. The Centre Hall Formation makes up the immediate and main roof members and is approximately 9.1 m (30 ft.) thick, consisting of medium-dark-gray limestone (Murphy et al., 2018). Situated in a syncline, the top of the Valentine Formation dips at approximately 19° with a strike of approximately N54E in the area of interest (see Figure 2)."

Jan 1, 2018

By C. A. Vining, J. R. Nopola

"Evaporites, such as salt and potash, pose unique problems to ground-support designs not encountered in other rock types. Evaporites are subject to continual creep and no amount of ground support can successfully arrest this process. Common ground-support techniques that are useful for most rock types may reduce the effective life of bolts in evaporite mines and can create unseen hazards. A different approach to ground support must be applied to provide long-term support in areas where high creep rates are present. The goal of effective ground-support designs in these situations is not to contain the rock and prevent it from moving; rather, the ground-support design must be able to move along with the rock and contain any fully detached slabs until additional remediation measures can be undertaken. The most appropriate ground-support designs will consider both the expected movement of the rock and the duration that the area needs to remain accessible.INTRODUCTIONEvaporites, such as salt and potash, pose unique problems to ground-support designs not encountered in other rock types. The factors that must be considered in design stem from the deformation behavior of salt, which can fail in a brittle manner, akin to most rocks, but can also deform in a slow, ductile manner, resembling the stretching and elongation of steel. The deformation behavior of salt has been well established in technical circles where it has been studied for decades (Hardy and Langer, 1984). Much of the research in salt mechanics is related to repository science, specifically at the Waste Isolation Pilot Plant (WIPP) in southwest New Mexico. RESPEC has been continually involved in the WIPP from the initial design considerations (Gnirk, Grams, and Zeller, 1977) to the current day (Keffeler, 2016) and has been able to leverage cutting-edge research of salt mechanics into practical solutions for mining operators. While a detailed description of salt mechanics is not provided in this document, Fossum and Fredrich (2002) include a fine overview of salt mechanics. The following list paraphrases their chapter on basic facts about salt to provide some context for the reader unfamiliar with salt mechanics:"

Jan 1, 2018

By Jun Lu, Greg Hasenfus

"In this paper, the mining experience and challenges for the first right-handed longwall panel in the Pittsburgh seam are introduced. The longwall headgate T-junction experienced very high face convergence (up to 2 feet), accompanied by roof sag, floor heave, and rib loading. The headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded.Different underground instruments, such as a roof scope, de-gas drill, tell-tale, laser meter, and Borehole Pressure Cell (BPC), were employed to explore the roof geology and to monitor the entry convergence and the stress changes in the pillar. In addition, the impact of other geologic factors, such as large overburden depth, laminated sandstone roof geology, soft floor, and large headgate equipment, were also analyzed. Subsequently, geotechnical solutions were provided to avoid or mitigate the impact of these challenging geologic factors.INTRODUCTIONIt is well known that high horizontal stress will affect the stability of roof, floor, and ribs within underground mines. In general, the headgate entries will experience stress concentration for the right-handed longwall face. On the contrary, the stress concentration will be in the tailgate entries for the left-handed longwall face (Hasenfus and Su, 2006). Without the stress shadow, the stress concentration in the headgate for the first longwall panel may be more significant (Figure 1).A mine in the CONSOL Pennsylvania Operation was extracting the first right-handed longwall panel in the Pittsburgh seam, which created high horizontal stress concentrations at the longwall headgate. Because of concern over soft wet floor within the syncline, floor coal had been left in place on development. Early on, upon retreat, the longwall headgate T-junction experienced very high face convergence, accompanied by roof sag, floor heave, and rib loading. The floor heave was exacerbated by the presence of floor coal, which buckled upward near the center of the beltline. Roof movement was occasionally aggravated by laminated roof conditions, but was kept in check by aggressive supplemental support including cable bolts, yielding props, cribbing, and roof mesh. Rib bolting and rib mesh helped to further maintain the entryway stability by keeping sloughage at a minimum. Nevertheless, despite the heavy support, headgate convergence was so large that, in a few places, it threatened longwall retreat and ultimately required the bottom to be re-graded."

Jan 1, 2018

By Meng Xiao, Peng Huang, Lizin Lan, Feng Ju, Shuai Guo

"Through changing the axial load on backfilling material compaction test to reflect different overlying strata pressure on backfilling material, the stress-strain relations in the compaction process of backfilling material under the geological condition can be obtained. Based on the characteristic of overlying strata movement in backfill mining, a model of roof thin plate is established. By introducing the stress-strain relation in compaction process into the model and using RIZT method to analyze the bending deformation of roof, the bending deflection and stress distribution can be obtained. The results show that the maximum roof subsidence and maximum tensile stress occurring at the center are 255mm and 5 MPa, respectively. Tensile fracture of roof under the geological condition of Dongping mine did not occur. The dynamic measurement results of roof in Dongping mine verify the theoretical result from the aforementioned model, thereby suggesting the roof mechanical model is reliable. The roof thin plate model based on the compaction characteristic of backfilling material in this study is of importance to research on backfill mining theories and application of backfilling material characteristics.INTRODUCTIONSolid backfilling mining (SBM) is a green mining technology in which the solid waste materials is placed into the gob to support the overlying strata and to control roof's subsidence and movement (Miao, 2012; Miao et al., 2010, 2015). SBM has been successfully used in several mines to solve many problems, including coal extraction under buildings, water bodies and railways, surface subsidence, and environmental problems. Good results have been obtained in many mines (Zhang et al., 2009). The key in the application of SBM technology is controlling strata movement. However, the critical factor influencing the controlling effect of strata movement is compaction characteristics of backfilling materials. Thus, a roof model of SBM is built based on the filling materials' compaction characteristics. A subsidence equation and the critical failure condition of roof was given and field verification was performed at Panel 15061 of Donping Mine."

Jan 1, 2016

By Donovan J. Benton

Photogrammetric methods are advancing rapidly and show considerable promise as a ground control research tool. The ability to quickly capture three-dimensional geometry, especially changes in geometry, in underground and laboratory settings is a significant advance from point distance measurements. Photogrammetry is being applied in both of these settings as part of the NIOSH ground control research. This paper describes these applications and the equipment and software being employed. It also describes tests conducted to quantify the accuracy of these systems. Accuracy varied with system specifics and procedures. A factory-calibrated camera produced results within 1/32 of an inch, plus 0.04%. A user-calibrated camera was found to be less accurate, at 1/20 of an inch, plus 0.24%. These calibrations demonstrate that photo grammetry can produce research quality measurements in laboratory and mine settings.

Jan 1, 2014

By David W. Evans

"Induced hydraulic fracture of strata during roof bolt installation is a potentially prevalent, but masked phenomenon within the underground coal industry. Previously reported resin testing programs (McTyer et al., 2014) examined the relationship between resin mixing effectiveness and varying bore hole diameter. The methodology employed within this earlier test program facilitated a further critical area of research – the measurement of back pressures generated within the bore hole during standard rock bolt installation practices. Experimental data has indicated that fluid resin can be pressurised to levels where it exceeds the compressive strength of the strata, inducing hydraulic fracture within the immediate area of the bolting horizon. The routine cycle of roof bolting serves to propagate this effect, progressively fracturing and delaminating the roof during mine advancement. This masked phenomenon can lead to a perception of difficult ground conditions - mining efficiencies and costs are therefore affected, with increased needs for additional support subsequently required to restabilise the inadvertently damaged roof.Further analysis of the parameters associated with resin bolt installation has now been conducted, assisting in the development of an empirical relationship between bore hole pressure, bore hole diameter and bolt insertion times. This relationship has been analysed for 15:1 ratio resins and 2:1 ratioresins, within 28mm and 30mm boreholes. Further to this, load transfer performance has been comparatively assessed for both 28mm and 30mm boreholes, suggesting that for 2:1 resins, acceptable resin mixing and load transfer can be obtained within a 30mm bore hole. The combination of 2:1 resins, utilised within a 30mm bore hole, may well provide the optimal solution to reduce the risk of hydraulic fracture in weaker strata during resin bolt installation.INTRODUCTIONA growing number of industry papers have previously investigated areas of concern associated with the performance of cartridge style resins in roof bolting, predominantly focussing on the effects of plastic film gloving, inadequate resin mixing and the pressurisation of resin within the bore hole. These three effects have a critical influence on the load transfer of the steel bolt element, through the cured resin and into the surrounding strata.Gloving occurs due to the plastic film of the resin cartridge partially encasing or wrapping around the steel roof bolt element – a known phenomenon over many years (Pettibone, 1987). The plastic film creates regions of discontinuity between the bolt, cured resin and borehole, reducing effective load transfer into the strata. Experimentation conducted into the effects of bolt ends fully encased by plastic film (Pastars and MacGregor, 2005) revealed that load transfer can be reduced by 85 to 90% in worstcase occurrences. It is also known that the aggregate filler size used within the resin can assist in shredding and breaking up the plastic film – this effect was observed in a previous study on resin mixing effectiveness (McTyer et al., 2014)."

Jan 1, 2015

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Aleksander Wrana

"The Carboniferous coal measures, mined across Europe including the major European underground coal mining countries of Poland, UK, Germany, and Czech Republic, suffer from increasing extraction depth. This results in major geomechanics problems associated with ground control and support design.With production being concentrated into ever fewer high performance longwalls, located at greater and greater depth, pressure to ensure the roadways’ functionality (required dimensions) continues to increase. Mining in deeper and more highly stressed mining environments creates several problems. The high stress and deterioration in geological and mining conditions in many cases causes problems with gateroads maintenance (due to excess convergence). That leads to costly production gaps, longwall slowing, transport problems, an increase in the methane hazard and in the general health and safety of the workforce, and deterioration in climatic conditions with major economic risk associated with interruption of the revenue stream. Time—and thus production—delays due to maintenance often result from insufficient geological and geotechnical data acquisition and misinterpretation combined with inadequate support for the type of rock mass.longwall face on the gateroad stability (described by the gateroad convergence, support load, and shape and height of the fractured zone around the longwall gateroad) are presented. The investigations were carried out in the longwall panel with roof caving located at the great depth, in conditions of the Upper Silesian Coal Basin in Poland.The measurement results showed that the gateroad fractures in roof strata began to occur at the distance of about 1000 m ahead of the face. Additionally, the load on support and gateroad convergence increased as the longwall face got closer.It is very important for coal mining research institutes and mine operators to investigate and develop practical solutions and apply innovative support technologies at a great depth (particularly for reinforcement and stabilization of roadways and other openings).Underground measurements of stability conditions around the gateroad is of great importance to mining practice, especially in planning and designing supports for longwall gateroads.The influence of the front abutment pressure results in an increase of support load, gateroad convergence, and shape of fractured rock zone."

Jan 1, 2015

By Douglas Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

By Rocky Wu

Rock bursts are one of the greatest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost-effective yielding rock bolt. This paper introduces a new yielding rock support: the Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150?250 mm (6?10 in) of deflection at 8?10 metric tons (MT) (7.9?9.8 t) loads for every 16.4kJ (12,096 ft lb) energy input. The bolt?s performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described; the dynamic testing results are discussed; and the features and application of the bolt are presented.

Jan 1, 2011

By Ashok Kumar, Rajendra Singh, Arun Kr. Singh

"A simple analysis of site conditions and capability of the mechanised depillaring (MD) operation found that this approach is suitable to address the strata control issues in coal pillar extraction under the weak and laminated roof strata of Pinoura mine. A continuous miner (CM) with a ram car and quad-bolter are used for single pass pillar extraction (first time in the country) to achieve a relatively faster rate of depillaring. A total of eleven panels are depillared under weak and laminated roof strata with a fair-rated rock mass rating (CMRI-RMR). It is observed that there is less influence of roof caving over the surrounding mining structures, especially those located out-bye the side of the extraction line. An attempt is made to quantify the goaf influence by field studies, which show that the maximum value of mining-induced vertical stress is 2.83 MPa, and the range of influence remains limited to around 15 m from the line of extraction. However, the problem of roof instability under the influenced zone was experienced due to the inherent nature of the weak roof strata. The chances of trapping of CM under weak and laminated roof strata of the panels is reduced by deriving a threshold value of the roof dilation, on the basis of a simple statistical analysis of the obtained field results. However, few incidences of roof collapses are observed over the CM due to the unpredictable behaviour of the geological structures below the freshly exposed strata, which also caused an obstruction in the speed of the extraction. This paper presents results of the field and laboratory studies, conducted for a successful application of the single-pass pillar extraction method, along with details of some CM trapping cases below the weak and laminated roof strata.INTRODUCTIONCoal is the major natural resource to meet the growing energy demand of India and this trend is likely to continue for the next 20 years in the country. A major part of the Indian coal belongs to Gondwana period, and only a small part belongs to Tertiary period. The estimated coal reserve in India per the exploration work done up to a maximum depth of 1200 m is 315.149 billion tonnes, including the proven coal reserve of 143.058 billion tonnes (CMPDIL, 2017). Even in presence of these huge resources of coal in India, there is a considerable gap between production and the users’ demand of coal. Most of the mines are operated by conventional semi-mechanised Bord and Pillar (B&P) methods; thus, the mining industry has gained a considerable amount of operational experience (Singh, Singh, and Dhar, 1996) and knowledge about strata behaviour (Singh and Singh, 1999; Singh et al., 2008) using this method. However, recently, the Indian coal mining industry has introduced some mechanised depillaring (MD) operations, where the level of production is relatively high. This approach of depillaring improves safety along with the production and productivity of a depillaring operation (Ram et al., 2017). The nature of the overlying strata of these depillaring operations vary greatly: from highly laminated, weak, and easily caveable to massive, strong, and difficult to cave."

Jan 1, 2018

By Shuren Wang, Wenbing Guo, Paul C. Hagan, Yanhai Zhao

"The overlying strata is often destroyed in large scale during shallow coal seam mining, and the sliding instability of the caved roof seriously threatens the safety of the mining field. The typical shallow coal mining in Shendong Mining Area in China was used as engineering background; the load distribution characteristics of the overlying strata were analyzed based on the monitoring data of the support resistance. Through theoretical analysis and numerical simulation, the formation and changing process of the pressure-arch in the overlying strata were studied, and the instability mechanism of the overlying strata was revealed by focusing on the accumulation and release law of the elastic energy in the pressure-arch. The results show that the continuous pressure-arch was formed when the horizontal stress exceeded the primary vertical stress of the mining field, and the elastic energy of the roof was released by the mining unloading effect. The elastic energy was accumulated in the pressure-arch, and the energy arrived the highest at the front arch foot. The accumulated energy at the arch foot was released by coal mining, and the shear zone could be formed. Therefore, the sliding of the caved zone along the shear zone induced strong roof weighting. The concentrated stress and the released energy during each mining increased with the panel advancing, and the height of the shear zone also increased. The conclusions obtained in the study are of important theoretical value to direct similar engineering practice.INTRODUCTIONThe instability of overlying strata during shallow coal mining, such as the large-scale roof falling and step-like ground subsidence, is a key problem that can restrict the safety mining in the mines (Ju and Xu, 2015). The self-bearing structure of the pressure-arch can form in the overlying strata after coal mining, and this structure can support the load of the upper strata and soil layer, so the weighting intensity of the panel is determined by the caved rock in the unloading zone under the inner boundary of the pressure-arch. A large amount of elastic energy is accumulated in the pressure-arch under the concentrated stress, and the released energy for mining is the internal cause of rock failure (Wang et al., 2017). It is an important problem to reveal the distribution characteristics of the stress and energy fields in the mine and to analyze the stability of the overlying strata during shallow coal mining based on the evolution characteristics of the pressure-arch."

Jan 1, 2018

By Peng Zhang

In a recent research effort, a laminated overburden loading model (as implemented in LaModel3.0 was compared with the results of ARMPS 2010, and the laminated overburden model was found to more accurately classify a ARMPS database of 52 deep cover case histories by a factor of 60% versus 54%. However, the LaModel analysis of each case study required several days to complete, as compared to a requirement of only several minutes for each ARMPS analysis. In the research presented in this paper, a computer code (ARMPS-LAM) has been developed to effectively implement the laminated overburden model into the ARMPS program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition and then automatically develops, runs, and analyzes a full LaModel analysis of the mining geometry to output the stability factor on the Active Mining Zone(AMZ), all without further user input. The present laboratory version of ARMPS-LAM can be run in batch mode; therefore, the ARMPS 2010 database of 645case histories can be analyzed very quickly. In an initial logistic regression analysis of this database, the ARMPS-LAM program was seen to be slightly more accurate than ARMPS 2010 by a factor of 71% versus 63%.

Jan 1, 2013

By Bo-Hyun Kim, Mark K. Larson

"While faults are commonly simulated as a single planar or non-planar interface for a safety or stability analysis in underground mining excavation, the real 3D structure of a fault is often very complex with different branches that reactivate at different times. Furthermore, these branches are zones of non-zero thickness where material continuously undergoes damage even during interseismic periods. In this study, the initiation and the initial evolution of a strike-slip fault was modeled using the FLAC3D™ software program. The initial and boundary conditions are simplified and mimic the Riedel shear experiment and the constitutive model in the literature. The FLAC3D model successfully replicates and creates the 3D fault zone as a strike-slip type structure in the entire thickness of the model. The strike-slip fault structure and normal displacement result in the formation of valleys in the model. Three panels of a longwall excavation are virtually placed and excavated beneath a main valley. The characteristics of stored and dissipated energy associated with the panel excavations are examined and observed at different stages of shear strain in the fault to evaluate bump potential. Depending on the shear strain in the fault, the energy characteristics adjacent to the longwall panels present different degrees of bump potential, which is not possible to capture by conventional fault simulation using an interface.INTRODUCTIONThis paper is part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bump-prone potential in highly stressed ground conditions. More specifically, this paper reports an exploratory effort with an unconventional approach using a numerical tool to try to better understand a possible scenario where bump risk might be increased—that is, a scenario involving a strike-slip fault. The objective is to assess whether a numerical tool might be useful or practical in forecasting bump potential associated with a strike-slip fault for a typical, structural geologic setting."

Jan 1, 2018

By Deno M. Pappas

The purpose of this U.S. Bureau of Mines study was to determine the material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining. Photographs of actual mine gob were used to approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted on simulated gob material from 3 different rock types. The study found that the nonlinear stress-strain curves obtained from the three materials were similar, and could be represented in terms of moduli as follows: Es = 2.36s + 1,360 (1) Et = 0.00181s2 + 9.33s + 294 (2) where Es = secant modulus, psi Et = tangent modulus, psi and, s = stress level (due to overburden), psi. These curves correlated well with the theoretical solution curves developed by Salamon. Other effects on gob behavior were attributable to these studied factors including void ratio, thickness-to-width shape ratio, and rock compressive strength. The generated equations should provide numerical modelers with a practical means of estimating gob modulus as a function of stress level.

Jan 1, 1993