Search Documents

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996

By Wouter Hartman

Xuandong Coal Mine is mining coal in one of the most challenging underground environments in the world. This work has found that it is not only challenging but it also has the composition for some interesting rock mechanics and ground control conditions. The paper highlights the extreme mining and rock mass behavior conditions encountered when mining coal at 900 m below surface. It was found that the ground control environment associated with geological weakness, low coal material strength and stiffness, was reasonably well controlled; however, the chain pillar geometry and design did not take these geological weaknesses into consideration. Some of the chain pillars employed were quite large, which resulted in floor punching and secondary floor heave, which causes extreme difficulty for production. No barrier pillar has been employed except for the center 164-m-wide main headings pillar with a w/h ratio in excess of 40. After assessing the location and geometry of a 200-m-thick dolerite sill overlaying the coal measures, we found the probability of it breaking up into to smaller fragments and producing a larger goaf to be low. Therefore, the influence of the dolerite sill on chain pillar loading is considered small compared to the low coal, immediate floor and roof rockmass strength. It is further recognized that horizontal stresses could be locked up within the dolerite sill, which would likely result in regional bending that would be distributed through the chain pillars. This has, to some extent, already occurred, and the effects have been seen and felt through excessive floor heave, pillar punching, and coal bumps (seismicity). We?ve also found that there was a need to employ basic rock mechanics principals in assessing the stability of future multiple seam mining layouts.

Jan 1, 2012

In this paper a numerical formulation is presented for determination of the axial load along a cable bolt for a prescribed distribution of rock mass displacement. Results using the program CABLE indicate that during excavation, the load distribution that develops along an untensioned fully grouted cable bolt depends on three main factors: (i) the properties of the cable itself, (ii) the shear force that develops due to bond at the cable-grout interface (i.e. bond stiffness), and (iii) the distribution of rock mass displacement along the cable bolt length. In general, the effect of low modulus rock and mining induced stress decreases in reducing bond strength as determined from short embedment length tests, is reflected in the development of axial loads significantly less than the ultimate tensile capacity even for long cable bolts. However, the load distribution is also dependent on the deformation distribution in the reinforced rock mass. Higher cable bolt loads will be developed for a rock mass that behaves as a discontinuum with deformation concentrated on a few fractures, than for one which behaves as a continuum, either due to a total lack of fractures or a very high fracture density. This result suggests that the stiffness of a fully grouted cable bolt is not simply a characteristic of the bolt and grout used, but also of the deformation behavior of the ground. In other words, the same combination of bolt and grout will be stiffer if the rock behaves as a discontinuum than if it behaves as a continuum. This paper also explains the laboratory test programme used to determine the constitutive behavior of the Garford bulb and Nutcase cables bolts. Details of the test setup as well as the obtained results are summarized and discussed.

Jan 1, 1996

By Mike Faure

Hercules cribs make use of timber loaded parallel and perpendicular to the grain. Maximum use is made of the orthotropic properties of timber resulting in crib- having superior strength, high initial stiffness and controlled post yield deformations. Blocks and timbers can be combined in many different ways resulting in thousands of different geometries. Each geometry has a specific combination of block on block, timber on timber and block on timber contact area which results in a unique performance. Each crib can be fingerprinted by defining four parameters relating to its load/deformation curve. If the geometry is known, the performance can be predicted with a high degree of accuracy. If the mine support requirements are known, the crib geometries can be designed which met theme requirements in the most cost effective manner Hercules cribs come closest to satisfying mine support requirements. Due to the flexibility of the concept and their superior strength, they can be employed in most mining situations to enhance safety, improve productivity, reduce working costs or improve profitability.

Jan 1, 1993

By A. W. Khair

This paper presents an analysis of fracture depth and intensity due to subsidence over the longwall panel. Sonic reflection techniques were utilized to determine fracture depth, and a variation of p-wave velocity was used as an indication of the fracture intensity. Instrumentation has been tested for consistency and accuracy first in the laboratory using small scale models, then applied in the field in two mine sites with different mining geometry and geologic conditions. A new sonic viewer was utilized for sonic velocity measurements. Regular hammering method was on acoustic source. The results were concurrent with monitored horizontal strain profiles and measured open fractures over the longwall panels.

Jan 1, 1989

By André C. Zingano

The coal pillars in room-and-pillar mining method are subjected to vertical stress due to overburden rock mass and horizontal stress relieve due to entries excavation around them. Some coal mining companies are applying rock bolts and steel straps to improve the pillar strength, consequently to reducing the pillar size and increasing coal recovery. This kind of approach deserves some discussion, whether it is pillar reinforcement or just rib support. The efficiency of pillar reinforcement (or rib support) is directly related to the initial load capacity of coal pillar, the type of excavation, and the width to high ratio of the pillar. The objective of this paper is to understand the mechanism of pillar reinforcement (or rib support) using rock bolts and steel straps on pillar ribs. Numerical simulation taking into account the relations listed above. The results showed that the increase of coal pillar strength is very short, and there is no influence on improvement of load capacity of pillar. However, the rib support avoids block falling, rib failure, and displacement, reducing the pillar failure propagation into the pillar center. Keywords: coal, pillar reinforcement, room and pillar.

Jan 1, 2006

By Tara Bajpayee

Modern, highly productive underground mining operations need to assure the safety of their workforce by understanding where major strata fractures and roof failures could occur. Mines depend on a host of tools to assess ground instability. In-mine microseismic monitoring systems with sufficient number of sensors have also been used to provide this information. These in-mine systems must be robust in design and moved regularly to keep up with the mining advancement. System performance issues depend on maintaining ever increasing cable runs, preventing component damage from mining activities (scaling, blasting, etc.) and avoiding signal degradation due to interference from mining equipment (fans, trucks, electrical equipment, etc.). A potential solution is to use a surface based monitoring system having sensors placed in boreholes above and adjacent to the underground mine workings. These sensors must be capable of detecting and locating strata fracturing associated with rock failure events. A great advantage of a surface based monitoring system is its independence from the underground mine infrastructure. There is less concern with cable maintenance problems, signal degradation by interference from mining activity, or loss of power from the mine?s power grid. The disadvantages include the cost of drilling boreholes and challenges associated with placing sensors in the boreholes, maintaining radio communication and solar power, and public interference (vandalism, etc.). This paper describes a case study where a surface based microseismic system, using triaxial geophones in boreholes drilled from the surface, was deployed at a large limestone mine. The system was operational during a roof fall that occurred in October 2007. It detected the first rock fracture event 17 minutes before the rock fall event. The geophone array was sensitive enough to identify all large rock fracture, impact, and blast events as well as medium size rock fracture events occurring close to the geophone array.

Jan 1, 2008

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

By Keith A. Heasley

Numerous different instruments and techniques have been developed for the purpose of measuring rock stress and stress changes around excavations. The interpretation of the output from many of these instruments has often been problematic. This paper covers the research performed in attempting to analyze one particular stress measuring instrument called the Borehole Platened Flatjack (BPF) . The approach used in this analysis was to combine the analytical solution for the displacements around a borehole and the analytical solution for the bore- hole-platen interaction with the empirical stiffness behavior of the flatjack. The resulting model of the BPF response was then verified using measured laboratory data with very good results. In addition, techniques for applying the method to the field are briefly discussed. The major accomplishments of this comprehensive modeling and testing program are; 1) the establishment of the critical installation and site parameters of the hydraulic pressure cell and 2) the development of a systematic procedure for calibrating the cell based on the given values of these critical parameters.

Jan 1, 1989

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

By Shuangsuo Yang

Based on field observations and physical modeling of simulated materials, the dynamic equilibrium principle on the whole interaction process between the surrounding rocks and support of large deformation roadways in coal mines has been developed. It explains the methods of forming the bolted strata and its changing load capacity with deformation. It also points out the factors and conditions for forming the bolted strata as follows: (1) many entries in coal mines are subject to large deformation. During their service life, it goes through the following process, elastic > plastic > fiacture > broken > loosening, etc. During this dynamic process, the mechanisms of supporting structure are changing and therefore the interaction between support and rocks experiences a process of dynamic equilibrium. Furthermore, the required supporting force for stabilizing the surrounding rocks shows overall decreasing trend; (2) the bolted strata is a special supporting structure consisting of bolt, rock skin protection devices and rock strata within the bolted horizon. As deformation increases, the supporting structure of the broken strata within the bolted horizon experiences a process of periodic change, from equilibrium > not equilibrium > equilibrium. Corresponding to this change, the supporting capacity of the bolted strata also fluctuates and gradually decreases; (3) under the bolted strata, the stability of a large deformation roadway is dynamic and step-wise; and (4) the formation of bolted strata, especially bolted broken strata depends on the existence of compressive force. Supporting the bolted strata is not constrained by the quality of the surrounding rocks. It has broad range of application.

Jan 1, 2005

By Mark K. Larson

Calibration of LaModel for deep coal mines begins with adjustment of overburden stiffness for load transfer distance. This calibration determines whether mining induced stresses are concentrated in the immediate abutment of the gob, or spread over a wider area. In the absence of site information, an empirically-based estimate is often used. Where data is available, a recommended calibration procedure can be followed, as is done in this case study at a deep western longwall mine, with minor modifications and extensions. In this case, data sources included borehole pressure cells, flatjacks installed in series with support Cans, and observed changes in ground conditions. Calibration was based on the first detection of mining-induced stress from the advancing longwall. Detection was found to depend on the type and sensitivity of measurement. Borehole pressure cell data with a 20-psi-increase detection threshold were chosen as the standard, in accord with data used in deriving empirical relationships. Application of this standard produced a load transfer distance estimate roughly four times the empirical relationship developed by Peng and Chiang (1984). This is a significant deviation with important implications for panel design at this site. Data from flatjacks, ground condition observations, and borehole pressure cells with higher threshold values, were tightly clustered and show load transfer distances from two to four times empirical guidance. Ratios between various measurements can be used to adjust measurements to the standard (although they may depend on mine geology). Once established, ratios can be used to adjust estimates, say from support flatjacks or ground observations, to the standard, where borehole pressure cell data is not available.`

Jan 1, 2012

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

By Ming Ju Liu

China has been suffering from the most serious coal and gas outburst accidents. The situation has become worse than ever with the mining of deeper coal seams at higher production rates in a more complex underground mining environment, in order to meet the huge national demand for coal-fuelled power plants. In the year 2007 alone, more than 30 outburst accidents occurred in underground coal mines with a death toll of 258, and in the year 2008, as of May 22, nine outbursts have already occurred in Henan, Hubei and Chongqing, killing 68 workers. At the same time, China also experienced new trends of coal and gas outburst accidents since its coal production boom in the year 2001. These trends are of great importance for government agencies, coal mine owners and operators to take initiative and effective measures to prevent and control the occurrence of coal and gas outbursts in China?s widely spread outburst prone mining areas. This paper presents outburst data of China coal mines since 2001 and describes new trends of outburst occurrence in recent years, which include outbursts coupled with shocks or rock bursts of competent roof, outbursts in mines under development, outbursts in new mines and mines that have never suffered outbursts before, outbursts in mines that are believed to be of low gas content as well as outbursts in more long-wall faces. Based on the observation of outburst occurrence in China in the period from 2001 to 2008 as well as mining and geological conditions, detailed analysis of the possible causes that led to those new trends of outburst accidents is conducted. The analysis helps shed light on possible future remedies and the necessary measures to alleviate or eliminate outburst accidents in underground coal mines. Suggestions are put forward on future studies that could be of interest to national and provincial government agencies regarding strategic policies, proper technical management practice, identification of outburst prone coal seams, online monitoring of impending outbursts as well as prevention and control measures.

Jan 1, 2008

By Anthony Iannacchione

Coal mine bursts have represented a major hazard for U.S. mining operations for more than 90 years. During this time, many prevention controls have been developed and tested. This paper reviews 11 prevention control techniques. Although coal mine bursts are not common events in most underground coal mines, their occurrence almost always requires a change in mining practice. Over the many years of dealing with these hazards, specialized requirements for layouts and novel extraction sequences have been developed on a site specific basis. The keys to mitigating risks are to properly assess the coal burst hazards and to possess the knowledge and skills to prevent or remediate their occurrence.

Jan 1, 2008

By Xu Lin Sheng

During the mining course, when the roof above coal seams is constituted by thick and hard sandstone (conglomerate), sudden roof movements often take place with great force and de¬struction which is the biggest danger to the safety and production. Such sever movements of the roof in mining directly relate to the rock mechanical properties which are the main fac¬tors that influences the regularity of hard roof movement and its destruction form. A significient work and important technical way for applying rock mechanics into mining en¬gineering is studying the rock mechanics of the hard roof and altering some of the rock me¬chanic parameters which induce the improvement of the rock properties in order to efficiently control the movement of the hard roof.

Jan 1, 1989

By Jeff Whyatt

Deformation of underground salt, trona and potash mines is generally time dependent, providing for gradual adjustment of strata to mining induced stresses. Time dependence can allow for higher extraction ratios provided eventual failure can be tolerated. However, this eventual failure can be violent if creep deformation can shift stress and potential energy to strong, brittle geologic units. The mine failure case studies reviewed here illustrate this process. Yield pillars and defects in bridging strata figure prominently in these cases. Yield pillars provide local and temporary support to the roof, temporarily delaying the cave; and allowing extraction ratios and overburden spans to increase beyond the long term capacity of overlying strata. Defects (faults, voids, thinning) of strong overburden strata reduce the critical span, sometimes to less than panel width. Analyses of many of these cases have focused on a cascading pillar failure mechanism, but recent work and this review point to failure of strong overburden strata as the essential element. The suddenness of failure and attendant seismic events pose hazards to miners and, in some cases, to those on the surface. Characterizing these failures is a first step towards recognizing and managing the risk of catastrophic collapse in underground mines.

Jan 1, 2008

By Holger Witthaus

Various seam conditions had been examined during longwall production at RAG German hard coal mines. Based on the field data a prediction method was developed considering separation planes as influencing factors for roof falls at the face. The characteristics, orientation, and density of separation are important factors on the occurrence of roof falls. In addition to geological influences, the performance parameters and geometry of support must be considered and optimized for the prediction and prevention of roof falls in a longwall face. Based on detailed macro- and microscopic investigations of e coal seams considering various ranks of carbonization, the origin and characteristics of separation planes are determined and a strata-specific influence on roof fall is interpreted. It was assessed that the coal face fracturing and displacement caused by the stress depend on the floor and roof strata conditions due to activation of the existing separation planes. Field studies are shown giving an idea of influences by advance rates of the longwall face, support delay and hydraulic pressure to the roof control in longwall faces in depth of more than 3000 ft. The analysis includes the application of specific software developed for longwall roof fall prediction as a result of a European research project. The software allows a laminar graphic display of roof fall probability, which is used for recognition of risk areas and risk management.

Jan 1, 2009