Search Documents

By R. D. Hutchinson

I consider it an honour to be the opening speaker in this afternoon's session on "Canadian Exploration". I also think it most appropriate that this joint meeting of the MMIJ and AIME should consider this subject, because Canada is a major exporter of mineral products and Japan and the United States are our two largest customers. Clearly, therefore, both countries have a valid interest in developments on the Canadian minerals scene. I represent the Mineral Development Sector of the Canadian Department of Energy, Mines and Resources. I will therefore speak from the point of view of the Federal Government. At this point I would like to acknowledge the help and constructive criticism I have received from several of my colleagues in Mineral Development Sector in the preparation of this paper. In any discussion of exploration in Canada, it is essential to emphasize at the outset that Canada has a federal system of government, with powers shared between Ottawa and the provinces. Under our constitution, the federal government has jurisdiction over the north, and over offshore areas, while the provinces own the natural resources within their boundaries. They control the systems of land acquisition for exploration and the terns under which mining titles are issued, and are therefore able to determine the rate and conditions of exploration and development of these resources. It follows that the Federal Government can influence the exploration and development of the provincial resources only indirectly by consultation with provincial authorities. However, once the resources are developed and begin to flow to market, the Federal Government can exert a much stronger influence because of its constitutional right to control both inter-provincial and international trade, as well as through its general fiscal and tax powers.

Jan 1, 1976

By Jeffrey A. Holcomb

INTRODUCTION The passage of Comprehensive Environmental Response Compensation and Liability Act (CERCLA/Superfund) as well as the Resource Conservation and Recovery Act (RCRA) and state laws, have placed added regulatory pressures on the mining industry. These laws which focus on the regulation of hazardous substances and wastes for the protection of the public health and welfare and the environment, present the potential for tremendous financial impacts and liabilities on existing mine operators and owners and/or potential mine operators/owners. This paper takes a brief look at these laws and presents an environmental audit procedure to identify environmental liabilities prior to mine land transactions. The environmental audit approach presented is an overview of the procedures that could be used to document, evaluate and inventory existing and/or potential environmental concerns. This audit procedure can be applied to developed or undeveloped properties and at active or inactive mining sites. REGULATORY OVERVIEW Mining environmental liabilities have been addressed in RCRA, Superfund, the Clean Air Act (CAA) and the Clean Water Act (CWA). Even though the U.S. Environmental Protection Agency (EPA) has determined that mining wastes will be treated as solid wastes under RCRA and not as hazardous wastes, these wastes could still bring about a great deal of financial liability under Superfund. The catch is if the mine wastes generated contain hazardous substances such as the heavy metals arsenic, beryllium, cadmium, chromium, copper, lead, mercury, nickel, selenium, silver, thallium, zinc and others as well as cyanide. Thus, it is not only important for a mine operator/owner or a potential mine operator/owner to know if the mine wastes generated are hazardous, but it is important to know if the wastes contain hazardous substances. Following is a brief overview of RCRA and Superfund and their potential implications. RCRA RCRA, which provides the basis for the regulation of solid and hazardous wastes, is applicable to active mining and milling sites. Within RCRA the definition of a hazardous waste is provided. This definition applies to owners and operators of mining and milling sites if the operator has stored, disposed or treated hazardous wastes on-site. If this is the case and if strict process control and waste management activities are not adhered to, environmental liabilities may be associated with the site. Superfund The 1980 Superfund law can be applicable to inactive mining sites or to inactive sections of an active facility. The provisions of Superfund call for the regulation of hazardous wastes and hazardous sub- stances disposal and release not only by the existing owner, but also for any previous owner. This concept of joint and several liability means that one party, as among many, can be held totally responsible for the costs of hazardous waste cleanup (Haller, 1987). Furthermore, liabilities under Superfund have also been applied back to past acts; thus, several mining properties, active or inactive prior to the 1980 Superfund law, are at risk of being placed on the EPA's National Priority List (NPL) for cleanup. Last years amendments to Superfund, known as the Superfund Reauthorization Act of 1986 (SARA), provided some significant developments for the mining industry. The major requirement of the amendments as it pertains to owners or operators of mining sites is that the EPA must revise its present Hazard Ranking System (HRS). This is important be- cause in most cases the primary reason for several mining sites having been included on the NPL was due to the large volume of wastes generated. As is typical at most mining sites, large volumes of low toxicity wastes are generated and the current HRS model prejudices against this. It should be noted that this provision only applies to sites that are not already on the NPL or have not been proposed for inclusion on the list.

Jan 1, 1987

By Matthew Anderson, David Day, Paul Smith

"The Midwest is presently the focus for Combined Sewer Overflow (CSO) abatement in the United States (U.S.). Most of the EPA mandated utility and municipal long term CSO abatement programs in large metro areas in the Midwest such as Cleveland, Indianapolis, Columbus, Chicago, St Louis, Akron, Fort Wayne, Louisville, Kansas City, Omaha and Pittsburg use or will use deep tunnels for storage and conveyance of CSOs. This paper will compare design methods specified and implemented for tunnel construction in Midwestern geology such as soft ground and mixed face EPBM tunnels, hard rock TBM tunnels, drill & blast tunnels, road header tunnels along with tunnel lining systems. It will also review the performance of successful CSO systems that include design life cycle, vortex and drop shaft configurations, pump stations, storage and conveyance strategies and long term operation and maintenance criteria. HISTORY and BACKGROUND Prior to development of mandated wastewater treatment plants, collecting both wastewater and storm water runoff in a single-pipe system was an efficient and economical solution. The early combined sewer systems were typically designed and sized to carry several times the average dry weather wastewater flows and not designed to handle a mixed volume of waste water and storm water during a wet weather event. Beginning in the early 1970s, federal legislation (Clean Water Act of 1972, Clean Water Act of 1977 and the Water Quality Act of 1982) changed how municipalities and industries in the U.S. were required to treat and discharge wastewater into the nation’s surface waters. They were mandated to treat wastewater at federal regulatory standards for discharge into surface waters that is safe for humans, wildlife and aquatic life. The wastewater treatment facilities that evolved were initially designed and sized to treat only the peak volume of raw wastewater flowing during dry weather. Combined sewer system control sections or relief structures were installed upstream of wastewater treatment plants (WWTP) and were designed to protect WWTPs from potential damage that would be caused if peak volumes of raw wastewater mixed with storm water runoff reached and overwhelmed the WWTPs."

Jan 1, 2016

By A. B. Holland-Batt

In the 1960s and 1970s, incremental development rather than innovation was the norm for gravity separation. However, the last 15 years have seen a number of new developments in this area. The article reviews the traditional gravity-separation techniques and then examines the newer developments such as centrifugal separators. Emphasis is placed on novel devices or improvements that offer better control or improved performance.

Jan 1, 1998

By Norbert Patzelt

Today the standard method for grinding ore is the wet process. This is mainly due to the fact that the downstream process is wet and considering the total circuit dry grinding is not the most eco­nomical method for the comminution of the ore. Presently in gold ore processing dry grinding is only applied in cases where whole ore roasting is required downstream from the milling plant or if organic carbonaceous matters and sulfides are the primary reasons for the refractoriness. Since dry ore can be fed to the roaster, a dry grinding mill can advantageously be applied. In cases where d1y grinding could be applied advantageously for instance if the ore contains water soluble material and wet grinding is not possible there are serious concerns prevailing within the industty against this technology due to several reasons. Besides of the aspects as discussed later in this paper, there are several plants in operation with little success and considerable operational prob­lems. The reasons for this often lie in the fact that the several com­ponents of such a plant are bought from independent sources with­out considering the system requirements. It is essential that the dry grinding plants require accurate design between drying, pneumatic transport and grinding of the ore in the circuit. This paper will address some of these concerns raised in the industiy from a mill vendor's view along with discussing the development for the selection and configuration of the various dty grinding circuits.

Jan 1, 1998

By Vernon R. Shorter, Wayne N. Clark

Introduction Coal is the US's largest indigenous fossil fuel resource and is used to power 57% of this country's electrical generation (NCA, 1986). Congress, however, is focusing its attention on the acid rain issue and public sentiment is leaning toward further curtailments of SO2, NO, and particulates from utility and industrial coal-burning facilities. The Cool Water plant has proven that integrated-gasification-combined-cycle (IGCC) technology can reliably produce economical electrical power while limiting SO2, NOx, and particulates to a rate of only one-tenth of the federal New Source Performance Standards for coal-fired plants. Process water requirements at Cool Water are 40% less than those of a conventional coal-fired utility plant equipped with flue-gas desulfurization units for stack gas scrubbing, thus reducing waste water treatment requirements (Clark and Shorter, 1985). The IGCC technology employed at Cool Water has now been demonstrated to efficiently convert coal to electricity in an environmentally superior fashion. The Cool Water Coal Gasification Program is an unincorporated California association of six partners whose commitment is proving that the integration of gasification with combined cycle power production (IGCC) is commercially viable and environmentally safe. The 120 MW Cool Water plant began commercial production on June 24, 1984. The Program is operating it for a five-year commercial demonstration period. The Program is about halfway through this period. Much of that which was intended to be proven is now fact. In this mid-term assessment, the authors report that the com-

Jan 2, 1987

By Adrian Smith, Debra W. Struhsacker

13.1 INTRODUCTION Cyanide is, a generic term indicating the presence of the cyanide ion (CN-). Cyanide is a very common, naturally occurring compound produced by many biochemical reactions. Many plant species synthesize organic compounds which contain cyanide in the form of cyanogenic glycosides (Knowles, 1976). For example, trace amounts of cyanide are present in the seeds and leaves of many members of the Rosaceae (rose) family (Kingsbury, 1964). Many common items such as lettuce, maize, sweet potatoes, kidney beans, (Oke, 1969) almonds, and cigarette smoke contain cyanide. As examples, a recent chemical analysis of chocolate-covered almonds measured a total cyanide content of about two ppm (Steffen Robertson and Kirsten, 1987); and the U.S. Surgeon General (U.S. Department of Health, 1964) has shown that cigarette smoke contains up to 1,600 ppm total cyanide. The chemistry of cyanide solutions is complicated because the cyanide ion forms compounds and complexes with many elements. Some cyanide species are highly toxic whereas others are relatively inert and harmless. Molecular hydrogen cyanide (HCN) is the most toxic form of cyanide. Under most conditions, HCN exists as a gas which readily dissipates or reacts with the environment to form less toxic or nontoxic forms of cyanide. Thus HCN is an ephemeral toxin, and many naturally occurring geochemical processes reduce the HCN concentration of a heap system with time. As discussed below, free cyanide includes the two species, ionic cyanide (CN-) and molecular hydrogen cyanide. Free-cyanide toxicity in man, mammal s, and aquatic species is we1 1 documented (Doudoroff, 1976; Ecological Analysts, 1979; Towill et al., 1978). The lethal doses reported for human adults vary with the type of exposure as follows: • One to three mg/kg body weight if ingested; • One hundred to 300 ppm if inhaled; and • One hundred mg/kg of body weight if absorbed. Acute toxicity of free cyanide to freshwater invertebrates ranges from 0.028 to 2.295 mg/l, depending on species and test conditions. Generally, free-cyanide concentrations greater than 0.1 mg/l are expected to kill sensitive species in freshwater or marine environments (Doudoroff, 1976;

Jan 1, 1988

By V. J. Hucka

Coal, which was discovered in Utah in 1849, covers about 18% of the total area. Production in 1981 vas more than 14 million tons. However, some Utah coal mines are quite gassy. If longwall face technology is applied, then a release of a high volume of methane may be expected during the mining process. Investigations on methane content have been made by use of an isothermic bubble desorbometer. The desorbable methane content of 5 m3 to 16 m3 of methane per ton of coal mined has been determined.

Jan 1, 1983

By S. A. Tims

INTRODUCTION The Falconbridge mine ore body extends about 1.6 km (1 mile) in length and the deepest developed ore is on the 6050 level below surface. The ore zone varies in width from a few inches to over 30 m (100 ft) and the average width is 4.9 m (16 ft). Access levels are driven in the ore at 53.3-m (175-ft) intervals. The principal method of mining is overhand longitudinal cut-¬and-fill. Prior to 1962 timber square-set stoping as a secondary extraction method was used for about 15% of the total production. Undercut-and-fill was intro¬duced at Falconbridge in 1962 as a potential replace¬ment for the square-set method in heavy ground. The undercut-and-fill method was developed by Inco in the 1950s, its principal application being to transverse pillar mining. Falconbridge made modifications to this method. A feature of the mine is the No. 1 flat fault which dips 0.79 rad (45°) towards the northeast. The main characteristic of the fault is the presence of large swells of ore directly under the plane of the fault. The ground under the fault area is highly fractured and associated with massive sulfides. In the past, the ore under the fault was recovered, with difficulty, by either tight cut¬and-fill or square-set stoping. In the 1970s these meth¬ods were supplanted to a large degree by the under-cut-¬and-fill method. An advantage of the current undercut-and-fill method which uses cemented fill compared to the cut-and-fill and square-set methods is the reduction of dilution due to better control of the walls. At Falconbridge mine, it is estimated that the grade of ore produced by undercut¬and-fill is improved by approximately 10% over other methods. Where undercut-and-fill is used in very weak ground, a much greater improvement in grade can be expected. Table I shows mining production for 1974. The undercut-and-fill method was first used at Falconbridge during 1962. The first longitudinal stope was prepared for undercutting by laying down laminated beams the length of the stope and installing a lagging mat floor on top of the beams. Unconsolidated tailings fill was poured on top of the mat floor. As the cut ad¬vanced under the floor, heavy posts were placed under the laminated beams at 1.8-m (6-ft) intervals. During 1966, a radical change was made to the method when tailings fill, consolidated with portland cement, replaced the unconsolidated fill. This development eliminated the laminated beams and heavy mat floor and greatly im¬proved the stability of the stope. This system, with minor variations, is currently used at Falconbridge mine. APPLICATION The undercut-and-fill method is used to mine in¬competent ground, sills or floor pillars under mined-out levels, or a block of ore isolated between levels. It is occasionally used to advantage in sequencing produc¬tion from various mining blocks. This is done by mining a block of ore cut-and-fill method and at the same time mining the ore block directly underneath by the under¬cut-and-fill method. The undercut-and-fill mill holes at Falconbridge are either boreholes, stripped timbered raises, or steel mill holes. Boreholes and rock raises tend to slough in heavy and broken ground which increases dilution when sloughing exceeds the ore width outline and also in¬creases the difficulty of moving down to start the new cut. For example, in one installation, a 1.2-m (4-ft) diam borehole sloughed to a size of 3.7 x 5.5 m (12 x 18 ft). The undercut-and-fill method usually requires a mill hole extending from the level below the ore to the top horizon of the ore block. The customary methods of providing a mill hole are: 1) A borehole is driven from level to level through the ore block and a chute installed on the bottom level (Fig. 1). 2) An existing raise is used as a mill hole. If the raise is timbered, a steel mill hole is installed inside the timber and tailings fill poured around the steel mill hole (Fig. 1). 3) An existing steel mill hole, situated at one end of a mined-out stope, is used as the mill hole for an ad¬jacent undercut-and-fill ore block. The mill hole posi¬tion is determined when planning the mining sequence of the first stope (Fig. 2).

Jan 1, 1982

By Steven L. Webb

In 1965, Monsanto started planning of a new dike (No. 15) for use in disposing of ore tailings at its Columbia, Tennessee phosphorus plant. Generally, in the phosphorus industry only clay tailings are produced making it necessary to borrow fill for construction of a retaining dike. Borrow area investigations indicated that weathered shales and limestones adjacent to the dam site would provide adequate construction materials. It was proposed that the more clayey weathered shales would be used for the impervious core and the more granular weathered limestones would be placed in the outer shell of the dike. A dike section is shown in Figure 1 with gradation curves for core and shell materials in Figure 2. Figure 3 shows an aerial view of the tailings pond and dike during first-stage construction. Although the borrow area explorations indicated that the weathering of the sedimen-tary deposits was highly irregular, it was not considered necessary, at the time, to specify special excavation techniques that would ensure a thorough blending of the materials in the borrow pit. Instead, because of the short haul distance, a scraper operation for both clay core and granular shell materials was adopted as the most economical construction method. Using this materials-handling technique, variations in permeability could be expected in the compacted layers inthe embankment. Where continuous layers of less clayey limestones were placed in the core of the dam, extending from the upstream to downstream shells, seepage losses would be expected to increase substantially. Upon completion of the damn 1966, and shortly after reservoir filling, it was apparent that the construction technique used had resulted in the formation of pervious layers through the clay core. Excessive seepage on the downstream face of the dike was noticeable within a very short time. A monitoring program was established, using piezometric observations and flow measurements. These data indicated that seepage should be reduced and the application of an asphaltic emulsion

Jan 1, 1971

By Xuebin Liu, Yi Shang, Can Zhou, Hongqiu Zhu, Junbo Du

In the neutral leaching process of zinc hydrometallurgy, the pH value directly affects the leaching rate of zinc calcine. However, due to the complex mechanism of the leaching process and frequent fluctuation of working conditions, it is difficult to control the pH value by manual control. Therefore, this study proposes a fuzzy control method based on rule extraction under multiple working conditions, and analyzes the pH control performance. Firstly, the different operating states are classified according to process mechanisms and the Pearson method. Secondly, under the framework of the active learning algorithm, the approximate linear dependence (ALD) method is introduced to iteratively select samples with rule information in the original sample set for manual annotation. Then, the support vector machine (SVM) method is used to extract fuzzy control rules in different working conditions. Finally, a fuzzy rule set is established according to the samples mapped by the support vector. The simulation results based on industrial data show that the proposed method has better control performance than conventional fuzzy control and proportional–integral–derivative (PID) control.

Apr 1, 2024

By Drupad B. Desai, Alexander Rosenbaum

In recent years, there has been an increasing use of two-pass tunnel lining system consisting of segmental unbolted expandable precast concrete initial lining and cast-in¬place concrete final lining in the United States. Used so far in soft ground tunneling performed under free air, it often includes a waterproofing or gasproofing membrane placed between the initial and final linings. This paper describes the utilization of this two-pass system for an extension of the Baltimore Metro, constructed in part under compressed air. It offers a description of the extension project, known as Section C; addresses the tunnel lining selection process and the design of the lining elements; examines the effect of the adopted lining system and tunneling technique on the design of the project's major structural components; and describes design modification instructions in order to accommodate constantly changing field conditions.

Jan 1, 1993

By Clyde N. Garman

Historically, Vanadium and Uranium have been precipitated together in carbonate sill circuits. A separation of the salts of the two metals was then made on the basis of the fact that the reduced, salts of vanadium are more solo to and those of uranium lose soluble than the respective salts of higher valence. In practice this was carried out by fusing the precipitated combined concentrate with salt, sodium carbonate and sodium hydroxide with oil soaked sawdust mixed into the charge as the reducing agent. Generally the fusion was carried out batch wise and the resulting slag or glass leached in water. A good, fusion and three or four decantation washes resulted in almost complete recovery of the vanadium in the liquid phase and a very high recovery of the uranium as a dense black U02 solid.

Jan 1, 1962

By J. A. Boyle

In the Frick District of U, So Steel Corporation, we have had more than 37 years of experience in the use of multiple-fan ventilation systems, in our coal mines. In our Colonial field, with a long belt installation, we have mined 85 million tons of coal with the use of the multiple fan system of ventilation. In our Palmer field, with the use of the same arrangement, we have mined 90 million tons of coal--a total of 175 million tons without one accident attributable to improper mine ventilation. The same system, fundamentally, has been installed in our expanding Robena operations and at its present stage of development we are using eight fans to ventilate this area. To date we have mined 55 million tons of coal with very encouraging results and again without any accidents attributable to ventilation.

Jan 1, 1961

By U. F. Beichmann

INTRODUCTION The City of Oslo together with the neighbor municipalities, Baerum and Asker, are presently building a jointly owned sewage treatment plant located on the west side of the inner Oslofjord. The project is scheduled for completion late 1981. Because the location of the treatment plant is at a distance of about 20 miles (30 km) from the city center, a discharge of more than 13 yds 3/sec (10 m3/sec.) of sewage and storm water will have to be transported over considerable distances. The topography of the area and the geological conditions early indicated that the only realistic transport method had to be through tunnels. As planning proceeded, full face tunnel boring emerged more and more as a favorable alternative to conventional drill and blast medhods. Today the scheme comprises nearly 25 miles (40 km) of tunnels being excavated by full face tunnel borers. In addition a number of access tunnels and cross cuts are to be excavated by conventional methods.

Jan 1, 1979

By James J. Fallon

Last summer Larry Miller of Roberts & Schaefer told me that his AIME committee would like me to present some thoughts on the marketing of industrial mineral fillers and pigments to this illustrious group in Las Vegas. Shortly after, Brian Coupe of "Industrial Minerals" (the magazine) notified me that I would be presenting a paper to the Fourth International Industrial Minerals Congress in Atlanta this June. It seems to me now it might have been more appropriate to reverse the papers. Las Vegas, a town based on risk, might want to hear what we have to say in Atlanta. The subject for June is "Risk Philosophies of U. S. Industrial Minerals Companies". However, upon reflection, marketing of industrial minerals reflects risk philosophies to a considerable extent, so we'll cut the deck and deal on the subject of marketing.

Jan 1, 1980

By E. L. Schrader

Statistical Process Control (SPC) is a cooperative arrangement between a component or raw materials supplier and a manufacturing customer. The supplier must analyze his own manufacturing process and determine, predict, and control those variable elements in the circuit which affect finished product characteristics according to the customer's specifications. The results include: control of fluctuations in product characteristics to a narrow range, close communication between supplier and customer, and an increased responsibility for quality control placed on the supplier. In the mining and. processing of airfloated kaolin some unique problems arise with the SPC concept: 1) The SPC system was designed for manufacturing facilities that did not have to deal with natural variations in their raw material; 2) The airfloat process is relatively simple and offers limited opportunity to change processing steps or "fine tune" a circuit for special product needs; 3) Determining adequate sampling frequency for a plant which processes hundreds to thousands of tons per day is statistically difficult; and, 4) Due to the variety of customer industries served, different SPC programs must be set up to deal with widely varying specifications. For airfloated kaolin, SPC is "in line" process control, not after the fact "quality" control. The emphasis must be on statistically valid sampling of the kaolin ore and complete monitoring of its path through the beneficiation circuit.

Jan 1, 1987

By Paul Eimon

In the world of minerals exploration, computer-oriented data storage and retrieval methods are being talked about, studied and researched. The goal is to facilitate the recording, collating, indexing, recovery, and analysis of mineral deposit-prospect data. A survey has been made of the various report forms, suggested outlines, and computer coding forms that are currently used in mineral exploration to index and/or describe mineral deposits and prospects. These forms have a number of common characteristics: location, commodities, type of deposit, host rock, etc. Such basic mineral deposit-prospect "data units" are part of most exploration programs. "Data units" may be comprehensive bound published descriptions of mines or mining districts or 3x5 file cards or elaborate computer coding forms being developed in Canada. Initial attempts to develop computer-oriented information systems have run into the same roadblock: the lack of a body of organized, processible data describing the basic qualities of mineral deposits and prospects. To solve this problem, international committees are considering coding forms, world-wide semantics, and rules or standards for data collection and description. It appears that mistrust and lack of understanding of the computer; fear of loss of proprietary information; and disagreements over terminology are distorting the picture of what has to be done if the mining industry is to grow into more meaningful information systems for mineral exploration.

Jan 1, 1969

By W. Irwin

As a consequence of the oil crisis of the 70?s, the commercial value of coal increased very sharply and an upward trend in coal prices although now less pronounced, continues today. The graph shown in figure 1 illustrates the trend in the F.O.B. price of U.S. metallurgical coal. This trend occurs during a time when mechanized mining is firmly established as a means of production throughout the coal mining world. With modem methods of mining, mechanical cleaning is a necessity and quality control is no longer entirely dependant upon coal face practice. The efficiency of fine coal recovery is of vital economic importance to present day operations and good practice in this field contributes significantly to improving profitability. Numerous processes are available for the duty and this paper discusses one such system, namely the practice of froth flotation.

Jan 1, 1980

Since gold was first discovered in Colorado in the late 1850s' mining has been a major part of the state's economic history, according to Stanley Dempsey, chairman and chief executive officer of Denver- based Royal Gold Inc. While the mining industry has seen some lean times throughout the past century, it has always bounced back. Today, dozens of major gold companies are headquartered in the Denver area. The state's coal mines produced record amounts during 1996. And even some of Colorado's uranium mines are resuming production. Dempsey joined other speakers in addressing the state of Colorado's mining industry during the Colorado Mining Association's (CMA) National Western Mining Conference. Some 800 people attended the CMA meeting, held Feb. 2-5 in Denver. The meeting was the association's 100th since it was incorporated in 1897.

Jan 1, 1997