Search Documents

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

Jan 1, 2006

By Steve Kral

Reducing the cost per ton and increasing productivity are key factors in a mine’s profitability. Mining companies can do little about commodity prices. So to keep a mine operating at a profit, management must reduce costs and improve worker and equipment productivity in every facet of a mining operation. From mining to crushing to processing, mine management is constantly seeking new methods and technologies to improve the way it mines minerals. And it is willing to borrow techniques used by other operators.

Jan 1, 2002

By D. McBride

Representative samples are required from process streams in order to accurately measure chemical and physical characteristics. This information can then be used by process operators and metallurgists to evaluate the process and effect control actions for the operation. The capture and presentation of representative samples can be critical to measuring values, such as elemental analysis and particle size, with on-line or near-stream analyzers. A comprehensive multi-physics model has been developed and used to better understand the effects of slurry flow and particle segregation under certain operating parameters. An algebraic slip model coupled with a free surface algorithm is used to track motion and position of particles and phases within a specified geometry.

Jan 1, 2009

By Christopher J. Bise

INTRODUCTION Traditionally, the purpose of mine ventilation has been defined as diluting, rendering harmless, and sweeping away hazardous gases which may accumulate in the mine workings. In addition, the ventilation sys- tem must keep the mine air as close as possible to the composition of the outside air in order to provide a healthy environment for mineworkers and to prolong the useful life of mine equipment. When plans are being developed for opening a new mine, sound engineering dictates that a calculated estimate be made of both the maximum air quantity requirement and the accept- able mine pressure (head) loss related to the under- ground layout and projections. For efficient mine ventilation, the two problem areas that demand constant attention are (1) the control of fugitive air (through short circuiting or leakage) and (2) the provision of ample airway capacity. Fugitive air is that quantity of air which enters the mine but short-circuits the mine ventilation system through improperly constructed stoppings, doors, overcasts, etc.; it represents an investment in power consumption (to move the air by the fan) while providing little, if any, return on the investment. Typically, efficient mines are those that can deliver 50% of the air handled by their fans to the working faces. Paying close attention to a new mine's ventilation system at the outset can provide numerous benefits during the later stages of mine development. It has often been noted that the main cause of trouble in many mine ventilation systems can be found within a radius of 2500 ft from the fan installation. Ample airway capacity is essential to maintain the mine's head loss within manageable limits. Similar to an industrial ventilation setting, the mine's headings are the ductwork for the handling of air. The difference between normal industrial ventilation and mine ventilation is apparent when more capacity is needed; a plant can install new or larger ductwork, but it is difficult for a mine to install new entries or enlarge existing entries. Air velocities are usually maintained under 800 fpm to limit the stirring up of dust in the intakes. With this in mind, it is usually simple to estimate the number of entries required in the ventilation system. The problem that often arises, though, is when the system's capacity is overestimated and the required head loss to achieve the desired quantity is excessive. Experience has shown that problems are often encountered when the mine's condition requires much more than three inches of water gage to ventilate the mine on a day-to-day basis. Thus, if proper attention is not paid to these parameters in the preplanning and initial development of a new mine, it may take an extremely high water gage to achieve the ultimate quantity. This chapter will not delve deeply into the theory of mine ventilation; many other books have been writ- ten on that subject. Instead, the following sections will point out the important considerations that should take place before the development of a mine ventilation system, as they relate to normal industry practice. FUNDAMENTALS OF AIRFLOW Volume Versus Water Gage The common method of measuring ventilation pressure is in terms of inches of water gage (wg); one inch of water corresponds to a pressure of 5.2 psf (pounds per square foot). Further, airflow follows a square-law relationship between volumes and pressures where, as shown in the previous section, a doubling of quantity requires a quadrupling of pressure. Table 1 shows how heads and quantities are related. Using Table 1, it is readily apparent that, for the same mining conditions, an increase in pressure from one inch wg to three inches wg results in only 34,640 cfm when the initial quantity is 20,000 cfm. Pressure Losses Pressure losses in mine ventilation systems are caused by friction between the heading walls and the air stream and by shock losses due to abrupt changes of the air stream caused by obstructions. The common pressure-loss formula for mine ventilation is: [ ] where H is the pressure loss in inches of water gage, K is the coefficient of friction, L is the length of the airway in feet, 0 is the airway perimeter in feet, V is the air velocity in feet per minute, and A is the cross-sectional area of the airway in square feet. Table 2 lists the US Bureau of Mines schedule of friction factors (K) for mine airways. Recent research indicates that the values of K are slightly less for coal mines than those presented in the USBM Schedule, and Table 3 should be consulted in this instance. It should be

Jan 1, 1986

By R. P. King

The MODSIM mineral processing plant simultor is used to find optimal combinations of target separation specific gravities in a typical modem coal washing plant. A plant that is set up with these optimal targets can deliver up to 10% more yield at the same ash content as the same plant set up with separation targets chosen by conventional methods. MODSIM is the only simulator currently available that can simulate the liberation of pyrite and other mineral matter during open- and closed-circuit grinding operations. The simulator can therefore be used to assess the benefits of grinding operations in the flowsheet.

Feb 24, 1997

By R. A. Franks

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system?s ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system?s ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2008

By Steve Kral

The mining industry in Colorado faces the same problems the industry faces throughout the United States and the world — record low commodity prices and increasing regulatory and environmental restrictions that seemed designed to curtail mining activities. Despite those obstacles, the mining industry in Colorado still contributes about $8 billion annually to the state’s economy in the form of base and precious metals, industrial minerals, coal and associated service businesses and jobs. So the 300 attendees at the102nd National Western Mining Conference felt reason-ably positive about the industry in their state. The meeting is the Colorado Mining Association’s annual conference and was held at the Broadmoor Hotel in Colorado Springs in November. The theme was “Mining in the New Millennium — Achievement + Innovation = Survival.” Experts from Colorado’s mining industry and abroad discussed the challenges faced by the mining industry as it enters the new millennium. They offered insights into how the industry will operate during the early years of the 21st century and how it will survive low prices and increased regulatory restrictions.

Jan 1, 2000

By Richard E. Thill

Engineering properties of rock are essential in most phases of mining from site reconnaissance through mineral processing. Review of the literature indicates, however, that property data is scarce for most coal measure rocks in the United States. The Bureau of Mines, U.S. Department of the Interior, has undertaken a wide-ranging testing program to provide more complete property data for coal strata in the U.S. coal basins. The property data are expected to have application in geophysical exploration, the development of pre- mining and hazard detection probes and instrumentation, mine design, engineering and rock mass classification, subsidence engineering, and ground control. This paper describes the comprehensive program encompassing in situ geological, geophysical, and geotechnical properties and laboratory determinations of acoustic, electromagnetic, physical, mechanical, and index properties and discusses results for 500 ft of coal measures at a minesite in the Northern Appalachian, Eastern Coal Province.

Jan 1, 1982

By Georgene Renner, William R. Yernberg, Steve Kral

Agapito Associates (AAI) provides consulting services in geo-engineering, mining engineering and related disciplines. Founded in 1978, the firm operates out of offices in Grand Junction, CO, Golden, CO and Lombard, IL. Members of the staff include mining, civil and geological engineers, physicists, geologists, numerical analysts, computer specialists, instrumentation specialists, plus administration and technical support personnel. AAI has provided consulting and engineering services to mining companies producing base metals, precious metals, coal, potash, trona, limestone, oil shale and salt, and to defense and nuclear-waste disposal industries. AAI also provides services for measuring in situ horizontal stresses using an advanced biaxial overcore stress downhole measurement system developed by Sigra of Australia. Since 1978, AAI has measured in situ stress in copper, oil shale, molybdenum, trona, limestone and coal mines, and in tunnels and concrete structures. Since 1994, the staff has completed 527 overcore stress determinations. AAI has the equipment and personnel for overcoring, sample coring and instrumentation installation in limited access, surface and underground mines. Portable Longyear CP-65 drills, borehole deformation gauges and strain indicators are used for difficult-access overcoring and are permissible for use in gassy mines.

Jan 1, 2006

By Hyung-woo Kim, Sup Hong, Sung-Soo Kim, Chang-Ho Lee

A deep-seabed integrated mining system, which consists of four subsystems such as riser pipe, buffer, flexible riser, and tracked vehicles, is presented in Figure 1. In order to collect more manganese nodules, multiple tracked vehicle systems should be used in a deep-seabed integrated mining system.

Sep 1, 2014

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

By Bradford F. Townsend

A study was made on six collapses that occurred during large-diameter tunnelling through weak sedimentary rocks and soil using SES methods in three stages?top heading, bench and invert. The collapsed lengths are between 20 m and 277 m. The collapses were re-mined using essentially the same tunnel-ling method with larger excavation profiles to accommodate the designed remedial measures consisting of ground treatment, pre-support and stronger initial support/outer lining required to carry higher ground loads acting in the collapsed lengths. The paper presents information on the collapses and the design and execution of the remedial measures.

Jan 1, 2008

By William R. Yernberg

The current state of the copper industry was the topic of discussion at the Copper 99 — Cobre 99conference held Oct. 10 to 13, 1999, in Phoenix, AZ. More than 700 copper-industry engineers, executives, consultants, academics, vendors and other interested parties attended. This successful and well-organized conference was the fourth in a series of international conferences devoted to the mineral processing and extractive metallurgy of copper. The 1999 meeting marked the first time that the conference was held in the United States. The meeting was co-organized by the Minerals, Metals and Materials Society (TMS); the Chilean Institute of Mining Engineers (IIMCH) and the Metallurgical Society of the Canadian Institute of Mining, Metallurgy & Petroleum(CIM). The meeting was also sponsored by The Society for Mining, Metallurgy and Exploration Inc.

Jan 1, 2000

By Manuel Arnáiz, Pedro R. Sola, Rogelio Baudot, Manuel Herrera, Carlos S. Oteo

The aim of this paper is to describe and analyze the ground treatment performed between January and May 2002 in order to increase safety during excavation and reduce instability problems along 180 m of tunnel, during the construction works associated with line 10 extension to the Madrid Metro. The tunnel was excavated using the traditional Madrid Method and in the section considered in this paper layers of sand were detected around the tunnel crown area with a significant presence of water, the in?ow of which needed to be controlled with a minimum impact on the surrounding environment.

Jan 1, 2003

By D. J. Duck

INTRODUCTION Construction of the 3,600,000 kilowatt Third Powerplant at Grand Coulee Dam started in late summer 1967 approximately one year after authorization by Congress. The project was made possible by a treaty with Canada providing for cooperative development of the Columbia River which was signed in 1961 and ratified in 1964. Description of the Work The existing Grand Coulee power complex consisted of a dam and two powerplants with a switchyard serving each plant, one on each bank of the river. See Fig. 1. The switching facilities were connected to transformers at the powerplants by overhead 230-kilovolt and 115-kilovolt tie circuit conductors. [ ]

Jan 1, 1997

By T. C. Souza Pinto

Because shape is an assessment of the three-dimensional form of a particle, it may be described in terms of sphericity (?), which is a measure of how closely a particle approaches a spherical configuration. In this study, Darcy?s law and the Kozeny-Carman model for fluid flow through porous media were applied to packed beds to determine the sphericity (?) of apatite particles. The beds were composed of glass spheres or particles of apatite (igneous from Brazil and sedimentary from the United States) of three classes of size (Class 1: -297 +210 µm; Class 2: -210 +149 µm; Class 3: -149 +105 µm). Glass spheres were used to validate the model because of its known sphericity (? = 1.00). Apatite particles, either igneous or sedimentary, showed very close values for particle sphericity (? ? 0.6). Observations on particle images conducted by scanning electron microscopy illustrated that igneous (? = 0.623) and sedimentary (? = 0.644) particles of apatite of Class 2 predominantly exhibit elongated shape. The close value of particle sphericity (? ? 0.6) showed by either igneous or sedimentary apatite may be justified by the similarity in particle shape.

Jan 1, 2009

By A. Adu-Acheampong

The Mid-Tennessee Zinc (MTZ) mines, comprised of the Gordonsville, Elmwood, and Cumberland sites, last operated 4 years ago and are undergoing rehabilitation to begin production in 2008. The mines utilize a random room-and-pillar mining method that results in complex ventilation networks. Upon decommissioning, the mechanical ventilation units were removed and disposed of and several shafts sealed. In an effort to re-open the mines and operate in compliance with imminent Mine Safety Health and Administration (MSHA) diesel particulate matter (DPM) regulatory limits of 160TC µg/m3, a new ventilation system was required. The new ventilation system was developed primarily based on the diesel equipment required to meet production. Particular emphasis was placed on the DPM, diesel equipment utilization, main fan sizing, and fan locations to enable the mines to meet MSHA?s ventilation requirements in a cost efficient manner.

Jan 1, 2009

By D. S. Saxena, Jack K. Tuttle

Lack of understanding of useful applications of explosives on construction work stem primarily from the fact that explosion is commonly associated with destruction. On rock excavation and other construction works a certain quantity of explosive is harnessed to perform useful work at the source e.g. blasts to disintegrate rock. Development in rock blasting techniques, including the use of multiple-row blasting with short delay ignition, have made it impossible to excavate rocks close to or below buildings even in closely built-up areas. To permit the use of explosives on construction projects, in ways that will not damage existing structures, guidelines have been developed from careful measurements of intensity of ground vibrations. Accurate electronic instruments are now available for doing this. PLANNING AND CONTROL Blasting operations must be carefully planned and carried out to avoid discomfort to persons or damage to property. This increase in the use of rock blasting in city areas alone has led to a number of problems due to ground vibrations, air shock waves, and the psychological effect of noise. While the latter seldom if ever causes damage, it does create irritation and discomfort to persons living or working near the blasting sites. A result of this is a steady increase in the number of complaints in respect of damage to houses and other premises. Many such complaints are genuine and damage may undoubtedly be caused when incorrect blasting techniques are used.

Jan 1, 1997

By R. A. Pyper, J. L. Hendrix

Laboratory leaching experiments were conducted to ascertain the effectiveness of acidic solutions of thiourea, CS(NH2)2, for dissolving gold from finely disseminated gold ores. The ore tested was from the Chipmunk ore body of the Northumberland mining district in Nye County, Nevada, USA. Extractions of up to 90% were attained from the ore. Extraction was shown to be dependent on thiourea concentration, ferric sulfate oxidant concentration, acid concentration, and leaching time. Optimum conditions were an ambient temperature leach near pH 1.0 utilizing 100 to 200 kg/ton thiourea and 50 kg/ton ferric sulfate for 8 to 24 hours.

Jan 1, 1981

By L. J. Moore

Introduction Hydrometallurgical solvent extraction (SX) processes – featuring large quantities of combustible or flammable organic solvents - are common in the mining industry for recovering non-ferrous metals such as copper, nickel, cobalt, uranium, tungsten, iodine and lithium. Recent fire loss incidents and the widespread use of sub-grade tank farms and piping trenches, plastic piping, poor drainage, and closely spaced buildings demonstrate opportunities to improve the use of Inherent Safety (IS) in this industry. The mining industry has designed and constructed facilities with an emphasis on personnel safety, production efficiency and cost effectiveness. The use of IS to eliminate or minimize property fire exposures has not seen widespread practice. Lessons learned from the mainstream CPI have not been communicated or applied. As an example, copper SX plants have consistently used design of gravity flow as a cost and production-effective solution for transferring liquids and minerals through the process. In fact, Jergensen1 recommends to “utilize gravity to the fullest extent possible” in design of SX plants. This philosophy has been achieved by laying out SX plants with process equipment at different grade levels so that solutions can flow “downhill”. Because of the use of large quantities of flammable liquids and the potential for these liquids - if released – to flow unimpeded into other areas – gravity SX processes represent severe inherent fire consequences unless costly barriers, drainage and channeling are also provided. It appears that little thought has been given to the fire protection consequences and challenges of this design feature during the evolution of SX plants and most copper SX plants constructed today use some form of a sub-grade processing area (tank farm) and one-way gravity flow. While this layout is used to assure a cost effective operation it has resulted in significant exposures to high value production. The use of sub-grade production units is an inherently unsafe layout where flammable liquids are used and is a layout that would rarely if ever be used today by the mainstream CPI. Gravity-assist layout is only one example where copper SX plants have been designed and constructed without IS in mind. The use of combustible and frangible corrosion-resistant materials – such as glass, wood and plastic - for flammable liquid storage, processing and piping systems has significantly increased the hazards of these facilities. These materials of construction are not rigorous and allow for rapid failure and release of flammable contents during fire exposure. The use of combustible or frangible systems to handle or transport flammable liquids is not a practice seen today in the CPI.

Jan 1, 2006