Search Documents

By Ryan P. Sullivan, Ben D. DiFiore, Robert J. Auber, Michael A. Piepenburg, Lisa M. Smiley

Pollution to Lake Erie will be significantly reduced by the Westerly Storage Tunnel (WST) system, which is mainly comprised of a 10,000-ft long tunnel and a dewatering pump station in the downstream tunnel shaft. Separate construction contracts for the tunnel and pump station required careful management of the interface risks. A key decision was to decouple the projects by relocating the mining shaft away from the pump station. The need to receive the tunnel boring machine (TBM) in the pump station shaft was eliminated by dismantling the 28-ft diameter TBM in the tunnel then carrying it back through the tunnel and up the mining shaft. This paper discusses how interface risks were successfully managed during design and construction to limit overall schedule impacts.

Dec 1, 2022

By M. L. Free

Acid consumption in copper heap leaching is determined by the minerals present in the ore. Gangue minerals such as biotite and chlorite consume acid together with copper-bearing minerals such as chrysocolla and malachite. Acid consumption is affected by the rate of acid application and the particle size. Some gangue minerals undergo alterations and cause precipitate formation during acid leaching. Other minerals form due to precipitation as dissolved ion concentrations from a variety of mineral sources combine to exceed saturation levels. Copper recovery is related to all of these events. This study presents information on acid consumption of various gangue minerals as well as data for copper recovery from an associated copper ore.

Jan 1, 2010

By S. C. Termes

As part of an effort to provide basic data on the fundamental scientific and engineering principles of minerals beneficiation, the Bureau of Mines is conducting research on the flocculation of mineral fines. This paper presents results of studies using crosslinked starches containing carboxyl, diethanolamine, iminodiacetic acid, and xanthate groups to flocculate hematite, goethite, chromite, manganrte, pyrolusite, cuprite, and cassiterite fines. The carboxyl and xanthate derivatives flocculated all minerals except cassiterite; the latter was flocculated by only the diethanolamine derivative. The iminodiacetic acid derivative flocculated hematite, goethite, chromite, cuprite, and pryolusite fines. Zeta potential measurements were made to help define the reaction mechanism responsible for flocculation. These measurements indicate that electrostatic attraction probably is not involved, except possibly in the case of the diethano lamine derivative. The separation of hematite from quartz by selective flocculation with chelating cross- linked starches under two pH conditions and with two dispersing agents is described. Best recoveries and grades were found when either the carboxyl or xanthate derivatives was added at the natural pH of the pulp in the absence of a dupersing agent.

Jan 1, 1983

By J. B. Hiskey

Thiourea is a reagent capable of complexing gold and silver. With the proper oxidant, thiourea can effectively dissolve metallic gold and silver. A thiourea leaching system possesses potential advantages over conventional cyanidation including acidic solutions instead of alkaline, cationic complexes in contrast to metal-cyanide anionic complexes, and faster leaching rates with acidic solution of thiourea. Generally, the rate of metal dissolution in thiourea solutions is fastest when ferric ion is employed as an oxidant. Acidic thiourea solutions for certain applications could offer a nontoxic and noncorrosive option for processing gold and silver. This paper provides information regarding the fundamental chemistry of the acidic thiourea system, and reviews the dissolution of both silver and gold in acidic solutions of thiourea. The recovery of gold and silver from acidic thiourea solution is discussed.

Jan 1, 1981

By T. Dombrowski

Acid-activated montmorillonite is used worldwide as a catalyst and as a sorbent for the enhancement and purification of petroleum products as well as vegetable and animal-based fats. The solid-acid character of the activated montmorillonite is imparted by the manufacturing process, giving it unique properties that are exploited in these industries. Several international companies and a multitude of local clay producers are focusing on improving the efficiency of their standard and specialized products. This paper will describe the use of acid-activated montmorillonite in traditional sorbent applications, as a solid acid catalyst, and other new uses.

Jan 1, 1997

By G. A. Gruber

A flotation process has been developed to successfully treat ore from the Santo Domingo phosphate deposit in Baja California Sur. The ore contained less than four percent P205 with quartz, silicates, and carbonates as gangue minerals. Flotation of the low grade feed In sea water required that the conventioinal Crago Process, comprising direct anionic flotation, deolling, and inverse cationic flotation be augmented by an anionic cleaner flotation step, phosphate depression, and a calcite flotation step.

Jan 1, 1986

By Gordon T. Clark, Stephen H. Gleaton

This paper discusses the conceptual design of cut-and-cover tunnels currently being considered as one of the replacement options for the earthquake damaged, elevated double-deck highway and seawall built in downtown Seattle 50 years ago. The 4.8 km (3 mile) long, 6-lane improvement consists of 1.6 km (1 mile) of at-grade roadway with aerial interchanges, 1.6 km (1 mile) of large two-level cut-and-cover tunnels along the Elliott Bay waterfront, and retrofit of the 50-year old, 1.6 km (1 mile)long Battery Street tunnel and north transition to grade. Construction of deep cut-and-cover tunnels, in complex glacial geology overlain by hydraulically placed fill immediately adjacent the existing sea wall, will require extensive use of concrete diaphragm walls, ground improvement and dewatering. The potential liquefaction and lateral spreading of the fill materials in this active seismic region pose significant design challenges and risk.

Jan 1, 2003

By Frederick McNeill, Mahmood Khwaja, Benjamin Lundsted, David Polcari, Michael S. Schultz, Timothy Clougherty

The City of Manchester, New Hampshire, is embarking on one of its largest public works projects in history to construct a 12,000 foot long, large-diameter, conveyance tunnel through downtown Manchester. This area has challenging geology with undulating bedrock (granite, schist, and gneiss) profile overlain by fluvial deposits. Understanding the subsurface conditions is key to mitigating project risks, establishing plan and profile for the tunnel, and selecting the most cost-sensitive and technically appropriate tunneling method. This paper presents the project team’s approach for conducting the ground investigation, developing preliminary subsurface profile, and the considerations for selecting the tunneling method.

Jun 13, 2023

By J. S. Lewis

Beneficiation and physical and chemical processing of non-terrestrial materials borrow strongly from terrestrial experience, but also involve the necessity of handling literally un-Earthly feedstocks, reagents, and environmental conditions. The present state of scientific and engineering understanding of the processing of non-terrestrial minerals, gases and hydrocarbons is reviewed with the production of rocket propellants, life-support fluids, structural metals, and refractories as the goal.

Jan 1, 1992

By Robert G. Beverly

INTRODUCTION Standards limiting the annual exposure of United States uranium miners to radon daughters were established in 1967 at 12 Working-Level-Months (WLM). The standard was reduced by a factor of three, to 4 WLM, in 1971. Currently, the standard is again being examined to determine if it should be changed. Since 1967, Union Carbide has calculated individual monthly exposures in company and contract-operated mines located on the Colorado Plateau. Although it has been possible, by extensive ventilation control measures and accurate routine sampling, to meet the current exposure standard, there are many miners whose exposures closely approach the 4 WLM standard for any given year. However, it was noted that for miners who work for any extended period of years the [average] exposure was much less than the standard. The primary purpose of this paper is to show that, in effect, any annual exposure standard to radon daughters results in a long-term exposure considerably below that standard. Further, most miners, due to their job assignments and/or employment habits, only receive a small fraction of the standard. HISTORY OF EXPOSURE STANDARDS Prior to 1967, radiation protection in uranium mines was fundamentally based on a radon daughter concentration guide. In 1960, the American Standards Association published mine and mill radiation protection standards (ASA-1960). The Colorado Department of Mines, in 1961, adoped a standard which followed the ASA Standard and provided that if concentrations exceeded 10 Working Levels (WL), the area was to be shut down until corrective action was taken; if between 3 and 10 WL, corrective action was to be initiated; between 1 and 3, additional samples were to be taken and individual exposures evaluated; and if below 1 WL, conditions were considered to be controlled. In 1967, the U.S. Department of Labor issued the first exposure standard which called originally for limiting annual exposures to 3.6 WLM but which was later changed to 12 WLM. The complicated regulatory developments leading to this standard have been described elsewhere (Beverly-1969, Rock & Walker-1970). Effective July 1, 1971, this exposure standard was lowered to 4 WLM per year, which is the current standard. Over the past year, there has been speculation about the potential risk to uranium miners working at the present standard. A recent NIOSH Study Group Report (NIOSH-1980) concluded: "There is also strong evidence that a substantial risk extends to and below 120 WLM of exposure." The 120 WLM corresponds to a miner working in uranium mines for 30 years, a rare occurrence, at an exposure rate of 4 WLM per year, an even rarer occurrence. On the other hand, the General Accounting Office, in a recent Report to the Congress (GAO-1981), was very critical of reports by NIOSH on general low-level radiation risks. The GAO recognized that”...important questions remain unanswered about the cancer risks of low-level ionizing radiation exposure;" and recommended that Congress enact legislation giving statutory authority to an interagency committee to coordinate Federal research on health effects of ionizing radiation exposure. The International Commission on Radiation Protection at its March, 1980 meeting recommended limiting the inhalation of radon daughters to 0.02 J per year, equivalent to 0.4 WL, which on an annual basis would be 4.8 WLM and noted it is common to reduce this figure by 20% for allowance in the case of uranium miners for external and/or dust exposure(Sowby-1980). This is essentially equal to the present standard of 4 WLM. As earlier uranium miner exposure studies are reevaluated, and as new studies are conducted, it is important that the relationship between regulatory standards and the resulting actual exposures be recognized. UNION CARBIDE URANIUM MINING EXPERIENCE Union Carbide started mining Colorado Plateau uranium-vanadium ores in the late 1920s for the contained vanadium values. In the early 1950s, the Atomic Energy Commission contracted Union Carbide to produce uranium at mills located in Uravan and Rifle, Colorado. The company now has over fifty years of mining experience in the area. Some mines are operated as company mines and others are operated by private mining companies under a contractual arrangement. Ventilation, sampling, and exposure calculations are carried out the same in contract mines as in company-operated mines. Data presented in this report do not differentiate between company or contract employees and include all employees who worked underground any portion of a year in Union Carbide mines from 1967 through 1980. At the peak of uranium mining activities in 1970, there were 577 miners employed at year end (285 company employees and 292 contract) and 52 mines in operation (8 company-operated and 44 contract mines). Contract mines varied from two-man operations up to 15 employees. Company mines were generally the larger operations and employed from 20 to 100 miners.

Jan 1, 1981

By Anand Kumar, Debasis Deb, A. K. Mishra, M V. N. S. PRASAD.

In the Adriyala project, shield-leg pressure data from all shields and shearer location with time stamp from a mechanized longwall face are monitored and recorded in a surface computer. The data contain random noise due to power failure, leakage of legs, bad sensor readings, and other maintenance or geomechanical problems. An algorithm has been developed to detect mining cycle parameters such as setting and final pressures and duration of the cycle from these data for the analysis of periodic roof weighting phenomena. The intensities and persistence of periodic roof weighting are vital information for mine management to make judicious decisions on longwall operation.

By J. Morris

Petro-diesel is a common collector for fine coal froth flotation but partitioning of diesel range organics (DROs) in process streams has not been widely studied. Preliminary research suggested that under normal dosing schemes total residual DRO in process waters should be limited to the sub-ppm water-soluble fraction (WSF). Further, polycyclic aromatic hydrocarbons (PAHs) should partition proportionately with DRO. The purpose of this study was to confirm these findings in laboratory flotation tests. Total DRO and specific PAHs were measured in tailings and concentrate streams, and coal recovery and ash rejection were tracked. Results show that concentrate waters consistently had higher DRO than tailing waters, and DRO in both streams generally increased with increasing diesel dosage. DRO again appeared to be limited to the WSF and PAHs tended to partition proportionately with DRO. Results indicate optimal flotation performance should generally coincide with minimal DRO partitioning to process waters. Under typical operating conditions residual DRO should not present an environmental concern; however, conditions should be avoided that allow significant overdosing of diesel.

Feb 23, 2014

By David X. Zhang

This paper describes the results of using shear flocculation and flotation known as aggregative flotation technique for the enrichment of coal-derived char produced from mild gasification process. Aggregative flotation is a separation process which involves the use of suitable aggregating liquid under the action of high shear forces to render hydrophobic surface of coal-derived char particles to aggregate in an aqueous slurry. The fine carbonaceous particles are aggregated into larger floes while the impurities remain hydrophilic. In subsequent flotation process, the char aggregates are then separated from mineral matters by aeration in the flotation cell. The floatability of char aggregates and removal of mineral matters from chars are studied in a lab scale flotation column cell. The effect of various operating parameters on the aggregative flotation responses is presented. Emulsification of aggregating liquid using high intensity agitation and ultrasonic energy provides excellent aggregating liquid dispersion and increases selectivity for char aggregation. In subsequent flotation process, it results in significantly increasing the flotation rate of char aggregates. The microscopic examinations of bubble attachment to coal-derived char particles under various aggregating liquid dispersion levels were conducted by induction time measurement. The distributions of hydrophobicity of char particles and char aggregates prepared under various aggregating liquid dispersion techniques were measured by film flotation. The char particles prepared under high intensity emulsification attach at significantly faster rates to air bubble and with lower mean critical wetting surface tension than that of char with direct aggregating liquid addition. An interrelationship of increasing in flotation rate/combustible recovery with decreasing in induction time, mean critical wetting surface tension and dispersion of hydrophobicity on the char particles and char aggregates were obtained.

Jan 1, 1992

By V. R. Burkhart

Pennsylvania Power & Light Company is an investor-owned public utility which was incorporated under the laws of the Commonwealth of Pennsylvania on June 4, 1920, with general offices at 901 Hamilton Street, Allentown, Pennsylvania. At the present time PP&L is operating five coal-fired steam electric stations, two hydroelectric stations and one steam heat plant which is being converted from anthracite to oil fired. In addition, PP&L is a partner in both the Keystone and Conemaugh mine mouth bituminous coal-fired steam electric stations in Central Pennsylvania and also part owner of a company which operates another hydroelectric station. PP&L plants, other than the two mine mouth stations, are located in Central Eastern Pennsylvania. (Figure 1) The company derives about 99% of its operating revenues from supplying electric service, while the balance is from the one steam heat plant serving the city of Harrisburg. The entire service area covering 10,000 square miles in 29 counties, has a population of approximately 2,300,000 people. The area served is mostly suburban. It includes 109 communities each having a population in excess of 5,000 people. The largest cities served are Allentown, Bethlehem, Harrisburg, Hazleton, Lancaster, Scranton, Wilkes-Barre, and Williamsport which range from 50,000 - 120,000 in population. So you see our service area does not include any major cities. The area has industrial, commercial, residential, agricultural and recreational activities that are linked with the Eastern Megalopolis by an extensive interstate limited-access highway system and railroad networks. We consider this Central Eastern Pennsylvania area we serve as the "heart of the market" -- an area with great growth potential.

Jan 1, 1973

By R. D. Rein

The Henderson mine is a large continuous panel caving operation in central Colorado. The orebody is roughly 760 m by 910 m and will be extracted from two production levels. Each level is divided into three north - south panels 244 m to 317 m wide. The general arrangement of a production level and its associated undercut drifts is shown in Figure 1. The production drifts (3.6 m by 3.7 m) are spaced 24 m apart center to center and have undercut drifts (3.4 m by 3.8 m) 17 m directly above them. The production drifts are interconnected with drawpoint crosscuts (4 m by 4.3 m) driven on 12 m centers. Drawpoint crosscuts receive substantial brow steel and concrete support prior to undercutting. The brow steel is a 15 cm by 46 cm wide flange beam with a 2.5 cm wear plate to box in the 'cave' side of the beam. The concrete is a minimum of 0.3 m thick and the batch design results in 27 500 kPa strength. The finished drawpoint opening is 3.7 m by 3.2 m with a choke area of 3.7 m by 2.4 m. (Figure la) Undercutting and bell formation is accomplished by blasting rings of 7.6 cm holes drilled from the undercut drifts. The rings have a burden of 2.0 m and six rings develop one complete bell.

Jan 1, 1985

By W. M. Lewis

Product losses to tailings ponds have long been a source of frustration for the mining and utilities industries. The utilization -of the Lewis Econosizer to recover lost products has proven to be very cost effective through reduced acreage requirements, cleaning costs and increased production. The unit is successfully operating in coal, aggregates, industrial minerals, clay, fly ash, heavy minerals and many other ores. Utilizing an upward flow of slurry in a free settling environment, particles stratify within the unit according to settling velocities and are removed as sized products. Ultra fines or clarified water is removed off the top of the unit. The Econosizer requires no power and only minimal maintenance.

Jan 1, 1998

By Joseph W. Mullan

The today status of air pollution control legislation and regulations can best be described as an exaggerated state of environmental limbo. The '70's began but one and one-half months ago yet it already has been very appropriately named "the decade of the environment." This certainly will be the decade for new legislation - new regulations and hopefully "Clean Air." Already Washington is faced with legislators playing "pollution politics" to the crowds. Students have redirected their efforts from Vietnam to the cleansing of the environment and everyone including the man on the street has become an environ¬mental expert. This is the decade we all face, but where are we today? Pollution is not a new problem. It has been with us for centuries and while much is left to be done, much has already been accomplished. I will try to make some comparisons of what I believe to be the good and bad points in the national air pollution control picture and hopefully will generate within each of you sufficient concern as to which comparisons are sound.

Jan 1, 1970

By Jean-Michel M. Rendu

Increasingly, geologists use geostatistical methods to evaluate drilling programs. The complexity of the methods varies with the nature of the available sample information, the objective of the statistical analysis and the geologist's experience. Occasionally, estimating the average sample grade is all that is required. In other instances a semivariogram calculation may be considered. If sufficient data is available, the geologist may wish to estimate blocks or panels of complex shape, using the kriging method of evaluation. Historically, the use of geostatistics by geologists has been limited by a number of factors, most significant being the difficulty in accessing and using computer programs needed to complete the necessary studies. Geologists are often working in remote areas from which electronic communication is unreliable, if not impossible. Even when access to computer programs is technically possible, the costs incurred in accessing and using these programs are often considered prohibitive. In many instances using the programs requires an understanding of computer systems far beyond that which a field geologist can justifiably be interested in acquiring and maintaining.

Jan 1, 1984

By W. Burger

For the development of deep, hard rock, mines fast access to the orebody is critical. In some cases the mineralized area is more than 1,500 m (5,000 ft) below surface. Excavation of shafts or declines is typically on the critical path of the project schedule. Saving time on those activities can significantly increase the net present value of the mining project. Mechanical excavation methods are a step-change in excavation performance and labor safety compared to drill-and-blast operations. In hard rock conditions, roadheaders cannot be used effectively, so disc cutting is the first choice. For excavation of declines, tunnel boring machines (TBM) can be used in many cases. These provide, in certain rock conditions, considerably higher production rates com-pared to drill-and-blast excavation. Herrenknecht AG has developed a vertical shaft sinking machine (VSM) that is able to excavate shallow shafts in soil and medium soft rock. The ground is excavated by a roadheader boom. The muck is removed by a slurry system or a pneumatic system in combination with hoisting of skips. These machines have been applied successfully on shafts down to 100 m (300 ft). A pre-sink for a deep mine shaft has been excavated by this technology. For deep, hard rock shafts, a new shaft boring system has been developed by Herrenknecht AG in collaboration with Rio Tinto. Based on proven technologies, the system uses a unique arrangement of existing proven technologies. The system integrates excavation, mucking, primary rock support, installation of the final lining and shaft infrastructure. This new system improves the health and safety of shaft construction. Detailed performance estimates indicate significantly higher shaft construction rates are possible compared to conventional shaft sinking methods.

Jun 1, 2010

By Robert L. Sundeen, Richard V. Wenberg

INTRODUCTION Shotcrete can be defined as spray-applied concrete with a maximum size aggregate in excess of 9.5 mm (0.375 in.). The concept evolved from guniting, which uses smaller aggregate and generally produces concrete with poorer physical properties. The larger aggregate used in shotcrete requires less water in the mix, while offering larger bonding surfaces, thus imparting greater tensile and compressive strengths. TYPES OF MACHINES Two basic designs of shotcrete machines in general use are the wet or prehydrated zero slump and low slump type, and the dry or nozzle hydrated machines. Fig. 1 shows a typical zero-slump machine in a con¬figuration commonly used for small-volume require¬ments. The prehydrated zero-slump machine mixes exactly proportioned batches in a sealed pressurized chamber. "Slugs" of hydrated shotcrete mix and com¬pressed air are sent through a distribution hose to the nozzle where the wet mix emerges as a spray. The spray is directed onto the rock surface by the nozzle operator. The low-slump machine is similar, except that a thick slurry mix of aggregate is delivered throughout the distribution hose to the nozzle. Fig. 2 shows a typical low-slump shotcrete machine used in moderate-volume applications. The nozzle-hydrated shotcrete machine accepts a premixed "dry" (4 to 6% moisture) batch of aggregate and cement. A constant feed of this mix is directed by compressed air through the distribution hose to the nozzle. At the nozzle, water for hydration is introduced into the emerging spray. The hydrated mixture is di¬rected onto the rock surface by the nozzle operator. Fig. 3 shows a typical dry-mix machine. The major difference between the two basic machine designs is the consistency of the shotcrete quality. Pre¬hydrated machines have high degrees of consistency and produce high-strength concrete, resulting from their ability to produce exact mixtures of zero or low-slump concrete within the machine. Nozzle-hydrated machines tend to produce poorer quality concrete because of the difficulty in controlling the water content at the nozzle. Water input essentially is an art. As such it is not precise, and the shotcrete produced is of variable quality. MATERIALS HANDLING Materials handling presents a problem to either type of shotcrete machine. At times considerable quantities

Jan 1, 1982