Search Documents

By R. G. Reddy, A. E. Torma

Bio-treatment of uranium contaminated soils from Fernald using the bacterium Thiobacillus ferrooxidans was investigated. The experimental results showed that extraction of uranium upto 99 percent from soils were obtained with 10 percent pulp density suspension and with addition of iron (3000 mg/l) after bio-remediation time of seven days. Application of the results to industrial practices is discussed.

Jan 1, 1995

By C. O. Brawner

A recent advance in slope dewatering-depressurization and stabilization is the use of vacuum assist horizontal drainage. (Brawner and Pakalnis) Horizontal drains have been used for several decades to reduce water pressures in slopes to improve stability. The benefit from vacuum assist arises from an increased hydraulic gradient caused by an induced negative atmospheric pressure. A research program included a laboratory model whereby the effects of vacuum drainage were evaluated. Three case studies are described where the technique has been successful. The first is in a rock slope where flows increased from 0.1 1/min. under gravity drainage up to 1.2 1/min, upon vacuum. The second study involves installation of 17 drains placed at a slightly downward gradient to intercept and de- pressurize aquifers under a major tar sand deposit in Canada. The third study was on a large open pit copper mine in British Columbia where flow increased about 30 per cent.

Jan 1, 1984

By Jerry Williams

GEORGE WEINMAN: At this time, our co-chair, Jamie Davis from Phelps Dodge, will come to the podium. JAMIE DAVIS: Our next speaker is Jerry Williams from Phelps Dodge, Morenci. Jerry is the maintenance planning supervisor and is in charge of preventative maintenance and maintenance scheduling. Jerry's group uses predictive tools to monitor and predict the equipment failure throughout the mine, from pumps to shovels to motors, you name it. The title of Jerry's talk is "If You're Not Using Predictive Tools, You're Behind the Curve." I’ll turn it over to Jerry.

Jan 1, 1998

By Scott Burchmore, Jason Emery, Michael Melville

This paper presents best practice data management for monitoring of extensometers in Australian underground coal mines. This work is based on the combined experience of the authors and the available literature. The information and ideas presented herein are a culmination of many years of database development founded from mine site-based ground support design, underground inspections, extensometer data management and data analysis. Each author has more than ten years’ experience as a practicing geotechnical engineer at several operating industry wide research project focused on utilizing mechanical extensometer data for data analytics and machine learning. Principal hazard ground control management plans, stipulated in Australian coal mining legislation, outline the mandatory installation of ground monitoring devices during routine mining activities. After 20+ years of data gathering the barrier to implementing modern data analytics remains the challenges imposed by inconsistent data structure and data quality. This inconsistency is still routinely found between sites, companies and mining regions. Through the relatively simple application of a standardized database structure, the potential to shift from simplistic tracking of trigger levels, siloed at individual sites, to an industry standard method for compilation & comparison of monitoring data is enabled.

Jun 25, 2024

By John MacDonald

An unstable economy has shown businesses what the mining industry has known for decades ? a successful business location today may not succeed in the future. Unexpected expenses, natural events and workforce changes have a big impact on the costs of production. To help focus production and maintenance budgets, mining executives are increasingly turning to production metrics to make key decisions. Role of mine and mill data Companies employ a variety of information systems to allow employees to accomplish their operational tasks, and each worker is focused on the metrics, or key performance indicators (KPI), for his or her individual function. For example, machine operators monitor throughput and cycle time to keep the machines running continuously and to meet daily production quotas. Meanwhile, the maintenance teams monitor machine performance, overall equipment effectiveness (OEE) and meantime between failure to predict and help prevent downtime.

Jan 1, 2013

By Maria S. Adusmilli, Bhaskara A. Rao, Jorge G. C. Barros, Augusto F. Mendonca

Lateritic gold has been the object of study only for a very few years, though nuggets have been mentioned in earlier works even as early as 1984 by Hartt in Brazil. In Mato Grosso State, lateritisation is intense, as is common in all tropical forest areas of the world. Exploration has revealed the presence of recoverable "nugget gold" of variable sizes (30 - 200 gms) but frequently of good size (0 - 40 gms), especially near Cuiaba and Alta Floresta regions. In both of them the host system is a lateritised breccia indicative of a fault or shear zone breccia, though in different lithological domains. The Cuiaba occurrences are phyllitic and show a profile as follows, from top to bottom: 1) Compact ferralite crust. 2) Oolitic to pisolitic compact crust (+ some gold). 3) Mottled concretionary laterite crust. 4) Lateritised "eluvial material" (gold nuggets). 5) Mottled patchy to banded laterite. 6) Banded lateritised phyllite with lenticular to banded goethite. 7) Altered red goethitic phyllite, with quartz veins (+ fine gold). 8) Unaltered grey phyllite with quartz veins (Protore). The Alta Floresta-Juruena River occurrences are volcano-sedimentary and show a profile as follows: 1) Deep brown siltitic, argillaceous and arenaceous material with organic matter (+ gold). 2) Modular and concretionary laterite, compact and indurated, with arsenophyrite in quartz fragments (gold nuggets). 3) Band with silty-clayey matrix and arenaceous in nature. 4) Bedrock meta-arcosian arenite. 5) Volcano-sedimentary with rhyodacites and andesitic basalts, with intercalations of arkosic and greywacke nature. Breccias and quartz veins, and granites associated in different portions (Protore).

Jan 1, 1988

By Nicholas Tabor, Norbert Fuegenschuh, Richard Taylor, Jean-Marc Wehrli

The Plymouth Tunnel forms part of the 16-mile long route of the Purple Line Light Rail Project promoted by the Maryland Transit Administration. The tunnel is approximately 1,220 feet in length with a shallow vertical alignment located beneath a residential area. Challenging mixed ground conditions included surficial soils, decomposed Saprolite, and highly weathered to fresh rock requiring the use of the Sequential Excavation Method (SEM) for construction. This paper discusses innovative approaches implemented during construction as well as challenges faced during planning and installation of a spray-applied permanent concrete liner.

Jun 13, 2021

By M. G. Mudrey

Considerable potential for metallic mineral resources in the lower Proterozoic rock of the Lake Superior region exists (Mudrey and Kalliokoski, in press). Most of the identified resources occur within a 2.0- to 1.9-b.y.-old lithotectonic assemblage characterized by extensive sedimentary strata in the north and thick volcanic se- quences in the south, all deposited on a two-terrane, composite basement of Archean age (DeMattis, 1989). Since the late 1960s, measured resources of nearly 90 Mt (100 million st) of typical volcanogenic massive sulfide at eight localities in Wisconsin have been discovered. The largest of these, near Crandon, contains about 61 Mt (67 million st) of ore averaging 5.6% zinc, 1.1 % copper, and 0.5% lead. Although none of these properties are in production, estimates by Mudrey (1978) suggest that Wisconsin could become a major contributor of newly mined zinc and copper in the United States. These discoveries and uranium and gold discoveries in the Canadian Precambrian are what have led to in- creased metallic mineral exploration throughout the northern half of Wisconsin (Fig. 1). In this chapter, we discuss the geology and legal framework in which the Proterozoic volcanogenic massive sulfide deposits were found. Exploration activities for other metals have generally been negative, and have been background noise for the legislative activities related to the massive sulfide discoveries. Uranium exploration has been consistently negative, although several different environments have been assessed. Other metal discoveries. such as titanium/vanadium, have been subeconomic.

Jan 1, 1991

By A. T. Yu

Once exploration is complete, "winning" of the ore can be viewed as fundamentally a bulk handling proposition. Whether it is to strip, break, size, extract, load, haul, or even process, the success of each of these phases will depend upon how effectively one can utilize-the methods and tools that are available in bulk handling. Since as much as 30 to 60% of the total delivered price of raw materials can be attributed to handling and shipping (ref. 1), this expenditure may spell the success or failure of an entire mining venture. In fact, it has become increasingly evident that handling and shipping are so intimately associated with mining that only when they are duly considered throughout the mine-to -smelter master plan as an integral part of a total system can an optimum operation be expected and the most economical ton of ore obtained, this total systems approach should not only take in handling and haulage in and out of the mine, but also storage and transfer at the terminals (ref. 2,3,t), including ship and barge loading and unloading which are likewise a major consideration (ref. 5). Much has been developed during the past century in bulk handling, particularly in its expanding use in the mining industry. In view of the major role bulk handling has played and will continue to play in mining, in commemorating AIME's centennial, this paper will attempt to outline the state-of-the-art at this three-quarter point of the 20th century - one that is marked by its industrial revolution and rapidly accelerating technological advances. Bulk handling systems Although many developments in bulk handling are worth noting. The most significant during the past three-quarters of a century are: the total systems approach to solving problems, automation, the increase in speed and capacity.

Jan 1, 1971

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By Thomas W. Turk

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By A. S. Winters

INTRODUCTION Homestake Mining Co. owns and operates the Bull¬dog Mountain mine near Creede, CO. Lead-silver con¬centrates are produced from ores extracted from narrow veins which dip from 1.04 to 1.39 rad (60 to 80°). An¬nual mill throughput is approximately 90 700 t (100,000 st). Ore shoots average 2 m (7 ft) in width and the ore is often weak, muddy, and poorly consolidated. Walls can be either strong or highly fractured along the strike of the veins. Cut-and-fill methods were initially selected to mine the deposit and considerable overhand mining occurred during the initial stages of the mine. Because of un¬stable ground conditions, mine management recognized that other methods would have to be employed. Undercut-and-fill mining was adapted to extract the loose ore from narrow veins and is presently the primary method used. Approximately 80% of the annual pro¬duction is extracted by this system. Loading ramps are positioned along the strike of the vein on 90-m (300-ft) intervals to allow for 45-m (150-ft) long cuts in each direction from the extraction raise. This interval was selected for efficient slusher operation and stope cycling. Loading ramps rather than chutes were selected for ore movement into 4.5-t (5-st) Granby-type cars because of extremely sticky ore conditions. Mined-out areas are filled with deslimed mill sands. Sand is pumped from the mill into two mine storage dams where the water is decanted. Each dam has a 544-t (600-st) capacity. Sand is pumped into the mine at a 30 to 40% slurry through 2195 m (7200 ft) of 51-mm (2-in.) thick wall pipe. When called for, sand is reslurried within the dams to a density of 55 to 65% and pumped to the particular mine opening requiring fill. Dry cement is added to the slurry prior to pumping. The capacity of the mine fill system is 20 t/h (22 stph). DEVELOPMENT Vertical development below the main adit level oc¬curs on 61-m (200-ft) intervals from an internal winze. Main haulage drifts or laterals are 2.7 x 2.7 m (9 x 9 ft) in section and driven parallel to the vein structures. Ground conditions generally dictate that better progress can be realized in the footwall than in the hanging wall. A distance of approximately 21 m (70 ft) is maintained between vein and drift openings to accommodate a smooth 18-m (60-ft) radius curve for crosscuts which are driven on 91-m (300-ft) intervals. Approximately 18 m (60 ft) of tail room is driven past the vein inter¬section to accommodate train loading. Ore and waste are hauled using diesel or electric driven locomotives operating over 18-kg (40-Ib) rail [762-mm (30-in.) gage]. Loading ramps are established above each crosscut¬ vein intersection. Scram drifts are then driven in the vein to determine the width and grade of the ore. If a prior decision to mine the block had been reached, then the scram is driven only far enough [about 12 m (40 ft)] to establish a drawpoint and scraper tail room. In most cases, the drawpoint is a 2.1 x 2.1-m (7 x 7-ft) cutout driven about 2.4 m (8 ft) into the footwall. On the level above, a raise bore station is established in the footwall to one side of the crosscut-vein inter¬section. The station is of sufficient size to accommo¬date a Robbins 41R raise boring machine. Support for the station is accomplished with 1.2 and 1.8-m (4 and 6-ft) roof bolts and wire screening. Once completed, a 152-mm (6-in.) concrete slab is poured and the raise drill set in position to center the 1.5-m (5-ft) diam hole approximately 1.8 m (6 ft) from the vein footwall. A 229-mm (9-in.) pilot hole is then drilled to the scram cutout below and reamed back to full diameter (see Fig. 1). STOPING Initial mining in a typical undercut-and-fill stope be¬gins from the top of the borehole. The initial cut can be either immediately beneath the track level or the old scram drift depending upon the particular situation. Cuts vary but are generally 2.4 to 3 m (8 to 10 ft) high. Support is accomplished by square-set timber, overhead caps, or roof bolts and screening depending upon ground conditions. Once the initial cut is removed, underhand timber and screen is installed and cemented sand fill placed. The stope is then ready for undercut mining. Prepara¬tion work begins with sinking 4.5 to 6 m (15 to 20 ft) on the borehole plus cutting a slot to the vein. As sinking progresses, hanging sets are installed to provide man¬way and service facilities. Hanging sets 1.7 m (5 ft 8 in.) long and 1.6 x 2.2 m (5 ft 4 in. x 7 ft 4 in.) in section are installed with steel hangers similar to shaft sets. Framed 203 x 203-mm (8 x 8-in.) timbers are made up in advance and shipped to the stope during sinking operations. When manway and service facilities are completed to the floor of cut to be mined, generally 3.65 to 4.3 m (12 to 14 ft) below the previous sand fill, the ore is removed to the hanging wall plus a round each way along the vein. Levelers or long stringers are then installed over the raise opening to support the work deck, slusher, and grizzly opening. All waste and ore from the sinking process is fed by gravity to the raise (see Fig. 2). Once the stope is equipped, mining pro¬gresses outward in each direction from the grizzly open¬ing. Stope equipment consists of 907 kg (2000 lb) pull air tuggers, timber skips, 11-kW (15-hp) ventilation fans, 15 to 22-kW (20 to 30-hp) electric slushers, 762 to 1270-mm (30 to 50-in.) scrapers, 67-mm (25/a-in. ) jackleg drills, as well as other drilling and blasting supplies. In narrow stopes [generally less than 2 m (7 ft) wide], no support is required for the underhand caps of the previous fill. Where wide sections in the vein occur, segment braces are installed beneath the caps to insure that the sand support cannot slip away from the hanging wall. Sections as great as 6 m (20 ft) wide and 4.5 m

Jan 1, 1982

By Ronald Allum

Arizona leads all other states in the value of gemstones produced with an annual production which exceeds $3,000,000. Gemstones are an important component of the mineral wealth of the State. Turquoise, peridot, chrysocoll a, petrified wood, fire agate and crystallized mineral specimens are among the gemstones commercially mined. Numerous additional deposits are operated by hobbyists. The State's reputation as a source of gemstones and specimens for the collector and lapidary adds to the economy of the State by attracting tourists. Production of gemstones further adds to the State's economy through employment in the value added gemstone processing industries and by employment of Native American craftsmen.

Jan 1, 1988

By L. A. Ruth

Introduction The US Department of Energy's Office of Fossil Energy has begun a new approach for developing the ultra-clean energy plants. This approach will allow the nation to continue to use low-cost fossil fuel feedstocks during the early decades of the 21st century. The new approach is called Vision 21. The overall goal is to effectively eliminate, at competitive costs, environmental concerns associated with the use of fossil fuels for producing electricity and transportation fuels. Vision 21 is based on the following three premises: •The nation will need to rely on fossil fuels for a major share of our energy needs well into the 21st century. •It makes good sense to rely on a diverse mix of energy resources, including coal, gas,

Jan 1, 2003

By I. E. Odom

The rare magnesium-lithium clay mineral hectorite occurs at many places in the McDermitt caldera of Nevada-Oregon. Commercial development of several high purity deposits began in 1986. The hectorite was precipitated in a lake environment formed after collapse of the McDermitt caldera. Hectorite beds and lenses are associated with volcaniclastic sediments, limestones, dolomites, zeolites and locally sandy bentonites. The high purity deposits appear to be associated with hydrothermal areas. The hectorite consists of extremely small flake-shaped crystals, and Ca is the predominant exchangeable ion. Its color ranges from white to light green. Commercial uses developed to date include high brightness magnesium aluminum silicate products, organophilic clays, pulp retention, and ceramics. The MAS is used as a suspending agent, binder, stabilizer and thixotrope in aqueous solutions for cosmetics, household cleaners, pharmaceuticals and miscellaneous industrial applications. Organoclays are used in printing inks and paints.

Jan 1, 1992

By W. W. Wen

The objective of this investigation was to study the electrokinetic behavior of oxidized coals to indicate the feasibility of separating oxidized coals from ash materials and pyrite by an mine flotation process. The effects of soluble inorganic electrolyte products from coal oxidation were also examined. The electrokinetic behavior of coals of different rank and degree of oxidation were studied by an electrophoreses technique. Generally, increasing the oxidation increases the negative value of the zeta-potential and decreases the isoelectric point (IEP). Flotation results indicate that the flotation recovery increases with decreasing pH values, and that with ferrous sulfate at pH 6.5 the flotation recovery is optimum while the pyrite was depressed. Comparing the flotation results with the electrokinetic results verified that in the presence of ferrous sulfate, the maximum hydrophobicity of oxidized coal with dodecylamine and frother is near its IEP which is around pH 6.5 to 7.0.

Jan 1, 1976

By Robert L. Major

The expanded role which coal has been assigned in the energy future of the United States has raised numerous policy questions. The very complexity of these questions makes them suitable to analysis by econometric models. However, as the Wall Street Journal indicated in its recent article, business' success with such models have been mixed. I have been asked to present my views as to how coal producers can use such models and in what ways the industry is likely to be impacted by such models. I do not presume to speak for the whole coal industry, but only to share with you the personal observations of one who has worked "both sides of the street", having been employed' both by government and a consulting firm prior to joining the coal industry. In my opinion, the use of econometric models to analyze the coal industry will impact the coal producers in two main ways. First, their use by government will have a profound impact on future government policies related to the mining, transportation and utilization of coal. Second, such models, when properly calibrated and refined, may become useful tools for the coal producers in doing market research and long-range planning. While the former has already begun to impact on the operating environment or the coal industry, the latter is still in the embryo stage.

Jan 1, 1977

By M. A. Bartkoski

Today?s surviving companies are being pushed to a heightened level of excellence due to market changes. Therefore, new business strategies must be explored. This paper offers a sequenced plan to retool, empower, and organize the entire team for a common goal. Integrity Process is an operating system that is very comprehensive and is integrated in every part of the business. It relies on a detailed prevention concept intertwined with accountability that produces individual efficiencies and team effectiveness. Integrity Process focuses on the importance between working from commitment motives versus compliance fears. The results are balanced in priority and truly yield a win-win for the owners, management, workforce, and the community. Integrity Process can and is being used in any industry that is challenged to optimize the relationship between people and process.

Feb 23, 2014

By K. Sharman

Quintette Coal Limited (managed and 50% owned by Denison Mines Limited) operates an open pit coal mine located in northeastern British Columbia, in the foothills of the Rocky Mountains. (See Fig. l). Mining commenced in 1982. The mine currently produces 4.75 million tonnes of medium volatile bituminous coal per year from three pits (Mesa, Wolverine and Shikano), using a truck/ shovel operation. (See Fig. 2). Conveyors and trucks transport run-of-mine coal to the heavy media/froth flotation process plan t, where it is cleaned and loaded into rail cars for delivery to the Ridley Island port at Prince Rupert, British Columbia. All coal is sold to the Japanese steel industry under a long term contract. The coal seams mined at Quintette are contained in the Lower Cretaceous Gates Formation. Mineable seam thicknesses vary from 0.6 m to 10 m. The regional structure of the area is typical of foreland fold and thrust belts, with open to tight folds and imbricate thrust faulting. The range of structural features found in the three pits, and their effect on mining, forms the subject of this paper.

Jan 1, 1991

By James M. King

Analytical models for transient groundwater phenomena, such as those of Theis, Cooper, and Jacob, are important but often limited tools for aquifer evaluation and drawdown prediction. Most were developed using simplifying assumptions which compromise their treatment of complex boundaries and most also contain functions that are mathematically complex and difficult to solve explicitly. Examples of such functions are the Bessel functions, the exponential integral, and similar well functions for leaky confined and water table aquifers. This paper describes the joint use of simple numerical techniques and numerical approximations of these functions to extend many analytical models beyond their conventional applications. The enhanced analytical methods represent many hydrologic problems more easily and realistically, permit a wider range of application, and often provide insight into the response of pumped groundwater systems without the need to resort to more complex numerical flow models. Use of the enhanced analytical methods usually requires the use of microcomputers due to the large number of computations. Examples presented here are the development and extension of type curves and the determination of drawdown distributions.

Jan 1, 1984