Search Documents

By A. Torrance, M. G. Seo

Velocity of detonation (VOD) is an important variable when evaluating the performance of mine blasts. Typically, for a VOD measurement, individual probes have to be loaded into each blast hole that requires a measurement, which increases the loading time and is not representative of the whole blast. Experimental studies of electromagnetic pulse (EMP) from the detonation of explosive charges show that electric and magnetic field signals are observed when chemical explosions occur in the air, at the ground surface, and in the underground. EMP has the potential to evaluate VOD of the whole blast without impeding the loading process. Due to a variety of physical causes which make the electromagnetic effects complex, measuring EMP of the detonation of explosive charges has not been fully studied yet. Five different antennae were tested with explosives, which are commonly used in mining industry. Among the five antennae, aluminum and copper tape, and wire were successful to detect the EMP. INTRODUCTION The measurement of the velocity of detonation (VOD) helps in evaluating and comparing relative performance of explosives in mine blasts. A VOD of an explosive is usually predicted by empirical mathematical equations or measured in-hole by VOD meters. However, conventional methods to measure a VOD have constraints: only a limited number of holes can be measured because cost of consumables for such systems is very high, and systems only allow a certain number of holes to be measured. The measurement cables have to be placed into the holes prior to loading with explosives which means that preparing to take the measurement is time consuming and has to be well coordinated with the mine. In order to evaluate VOD for a whole blast, there is a possibility of using electromagnetic pulse (EMP) from the detonation of the explosives. As there are many parameters that affect the generated EMP from explosive charges, measuring EMP of the detonation of explosive charges has not been fully studied yet. Most studies conducted relate to military related explosives, not the ones frequently used in mining industry. This research has been performed to have a better understanding of EMP from the types of explosives which are commonly used in the mining industry. To discover a way to detect EMP efficiently, five different types of antennae have been studied in the air and in the underground blasting conditions: coil, monopole rod, log periodic, wire, and aluminum and copper tape. LITERATURE REVIEW Conventional methods of measuring VOD Over the years, demands for more accurate theoretical predictions and physical measurements of the effects of the explosives have increased. Especially when both demand and commodity price decline, mining companies are keen to understand the effectiveness of explosives since it has a direct relationship with fragmentation, which influences their production rate. Since the 1940s, various methods have been devised to determine VOD of explosives.

Jan 1, 2019

By James M. Peay

This paper discusses the recently completed organizational development research project, which was addressed to the underground mining industry. The three specific purposes of the project were as follows: (a) to determine whether Organizational Development approaches are feasible in the mining industry, (b) to provide a demonstration that Organizational Development methods can successfully contribute to the safety of underground mines, and (c) to compare the efficacy of classical Organizational Development methods, which are highly trainer- intensive, with trainer-nonintensive management development approaches. The term "Organizational Development" (OD) is here broadly defined as a management intervention for the purpose of assisting an organization with the solution of problems, which are seen by the organization as important. More specifically, we can define OD as a planned effort to improve the effectiveness of an organization through (a) team building and problem solving, which concentrates on the issues of immediate concern to the organization, and (b) efforts to improve organizational communication at all levels of the organization.

Jan 1, 1983

By D. W. Park

Longwall Strata Control and Maintenance System (LoSCoMS) is a software and data communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels including excessive shield load, low setting pressure, leg leakage and poor shield performance, eminent maintenance problems, etc. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems of their longwall panels. Two years of experience with this system is covered in this paper.

Jan 1, 1998

By W. J. Atkinson

Since the inception of the Ashton (formerly Kalumburu) Joint Venture in 1972 the parties have expended 524 million in exploration for diamonds in the Kimberley region. This has resulted in the discovery of the currently subeconomic Ellendale deposits in 1976/77 and the economic Argyle - Smoke Creek Deposits in 1979/80. In addition to Argyle and Ellendale some 90 kimberlitic and lamproitic bodies have been discovered grouped broadly into three provinces, on the west, east and north margins of the Kimberley block. These bodies range in size from dyke-like features less than one metre in width to pipes with a surface area of 128ha. The bodies with larger surface area are volcanic crater deposits, infilled with air-fall and water deposited tuffs and epiclastic sediments.

Jan 1, 1984

By J. Seifert, L. Hunter, P. W. Conrad, S. Rosenthal

"The goal of the protocol for reclaiming in-pit tailings ponds to exceed federal and state regulations was to develop a series of steps that can be followed to design, operate, and reclaim a tailings disposal pond that will develop into grazing land with a wetland for open pit sand mines in warm dry climates. By incorporating a wetland into the reclamation design, the post mining land use gives back to both the wildlife as a source of water as well as providing for a diverse range of post mining land use including but not limited to livestock grazing and ranch land use. An example design was completed using this protocol to demonstrate how the protocol can result in in a well-designed, reclaimed tailings disposal pond. BACKGROUND In an industry plagued with decaying historic mine sites, the public’s perception of mining appears to be poor. While modern mines are closely monitored and generally managed by ethical professionals, history still influences how the public perceives the mining industry. From collapsing abandoned underground workings to historic tailings dam failures, the failure to account for the environment in the past seems to affect public perspective on mining today. In a 2013 “Opinion Former Survey,” a survey conducted through interviews with a diverse range of stakeholders in various gold companies, it was noted that the most serious challenges facing the mining industry were environmental concerns and the permitting challenges associated with them (Council). In another article, this time focusing on Australian citizens and their perspectives of the mining industry, it was found that the majority of those surveyed had a big concern over the environmental impacts of mining especially when it comes to water quality and quantity (Scan). The statistics portrayed in these articles illustrate that today’s mining engineers needs to make more of an effort to change the public’s perspective of mining by being more environmentally aware. These engineers should be continuously asking themselves what they could be doing better from an environmental perspective to ensure that history is not repeated and that natural resources are used as efficiently as possible."

Jan 1, 2018

By S. G. Malghan

Flotation is the primary method for copper minerals separation from porphyry ores. The need to process difficult-to-float porphyry copper ores presents challenges to engineers and scientists in several areas. This paper is concerned with summarizing generalized problems faced in the processing of porphyry ores and treatment methods to overcome the specific problems. Though some of the problems are interrelated the problems have been classified into three broad catagories. The case studies of some of the successful applications of innovative methods to solve problems related to ore mineralogy, metallurgical aspects of ore treatment and process variables show that quite often the problems are solvable by a judicious choice of flotation variables.

Jan 1, 1984

By R. R. Givler

Since the 1860's the good ole days, oil has been nozzle fed to burners under pressure atomizing the oil into droplets -- 1960's has produced vaporized oil that burns oil with the flame color and consistancy of gas -- If you can tell the difference by looking at the flame, gas or oil I?ll buy the lunch. First, we must ask, "Why all the excitement about Blue Flame?" This question is best answered by you after you have studied the principle of operation and see the result. I will attempt to explain both of these so that you can draw your own conclusions.

Jan 1, 1975

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By C. A. Rowland

Introduction Rod mills are horizontal, cylindrical, rotating, tumbling mills in which steel rods, that are usually about 6 in. shorter than the length of the grinding chamber, are used for grinding media. Fig. 33 shows a cutaway view of a rod mill. Rod mills were first used around 1910 because of their ability to grind in open circuit, consistently produce a uniformly sized prod¬uct, give greater continuous availability, and give lower maintenance costs. They have basically replaced roll crushers and coarse grinding ball mills in comminution flowsheets. The present 20-ft limit on rod length, based on rod manufacturing methods, and the pulp flow char¬acteristics, that influence mill capacity, have established the maximum rod mill sizes' of 15 x 21 Vs ft using 20-ft rods and drawing from 2,200 to 2,300 hp. Rod Mill Uses. The principal uses for rod mills are: preparing feed for ball or pebble mills, grinding gravel or aggregates to the size analysis required for making concrete sand, preparing coarse agitator feed for leaching operations, and for primary grinding circuits, particularly in industrial mineral applications. Wet grinding is the most frequently used grinding process for rod milling. There are a few special cases where dry rod milling is used. Preparing feed for ball or pebble mills is the most common use for rod mills. In ferrous and nonferrous ore concentrators, wet open-circuit grinding is used to prepare ball-mill feed. Figs. 34 thru 37 show the four basic grinding circuits used in these concentrators. In rod mill-ball mill grinding circuits, where the rod-mill discharge contains 25% or more of the grinding circuit product-size material, the rod-mill discharge can be fed to the ball- or pebble-mill classifier as shown in Fig. 34. This is the most frequently used rod mill-ball mill circuit in the nonferrous ore concentrators. In a few concentrators such as Anaconda's Weed concentrator,55 the rod mill discharges to one classification stage which makes the same or a slightly coarser particle-size cut as the classifiers used to close the ball- or pebble¬mill circuits, as shown in Fig. 35. In concentrators where rod mill-ball mill circuits are used to grind low grade magnetic iron ores such as Reserve Mining Co., Silver Bay, Minn.; Erie Mining Co., Hoyt Lakes, Minn.; Eveleth Taconite Co., Forbes, Minn.; US Steel, Mt. Iron, Minn. and Atlantic City, Wyo.; Inland Steel-Jackson County Iron Co., Black River Falls, Wis.; and The Cleveland-Cliffs Iron Co., Adams mine, Kirkland Lake, Ont., the rod mills discharge to rougher magnetic separators (cobbers), the concentrates from which are fed to a ball milling stage as shown in Fig. 36. The same basic circuit is also used with gravity concentra¬tion methods such as spirals (Hanna Mining Co., Groveland, Mich.), tables (St. Joe Minerals, Bonne Terre, Mo.), and jigs. When the rod-mill discharge contains less than 25% of the grind¬ing circuit product size, this indicates an ore that does not readily produce the fines needed to help carry the coarse feed into the ball charge. When this occurs, the fines in the rod-mill discharge are needed in the ball mill or pebble mill so the rod-mill discharge flows direct to the second-stage mills as shown in Fig. 37. Rod mills are used to make feed for open-circuit ball mills such as those used in wet grinding cement raw material (American Cement, Brennan Ave¬nue plant, Detroit, Mich., and Port Huron, Mich., plant, and at the South Dakota State Cement plant, Rapid City, S. Dak.). Grinding gravel or aggregates to the size analysis required for making concrete sand is used in areas where natural sand of the proper particle size gradation required to make concrete is not availa¬ble. Three-quarter inch crushed aggregate is ground to 4 mesh using center peripheral-discharge rod mills (Fig. 38) operating in open circuit. US Corps of Engineers specifications state that the sand product be 93-100% passing 4 mesh and contain no more than 3-7% passing 200 mesh. It may be necessary to classify the rod-mill discharge to remove any excess -200 mesh sand produced in the rod mill. Particu¬larly when processing aggregate with high abrasion indices, center peripheral-discharge rod mills are used instead of hammer mills, fine bowl crushers, and crushing rolls for the production of specification sand. If the -4 mesh size fraction of the rod-mill feed is removed

Jan 1, 1985

By Karin Bäppler

A new polyhalite fertilizer mine is currently being developed in the UK by Anglo American Crop Nutrients. The project includes the construction of a Mineral Transport Tunnel almost 37 kms long to house a conveyor belt that will move polyhalite from the production shaft at the mine to a materials handling facility at the port. The project sets a new standard in terms of an ultra-long tunnel drive and sustainable, environmentally friendly and efcient material transport. The paper highlights in particular the . m diameter TBM in use for the construction of the ultra-long tunnelling section.

Jun 23, 2024

By M. Duane Lackey

Electric drives hire done outstanding job in many-fields that are related to the mining industry. The equipment that is offered for electric-trucks was developed from the traction equipment which is used on the diesel electric locomotive. Rotating equipment available for use on electric trucks is identical in principle to that which is used on these locomotives. In as far as it is practical, similar controls are used. Another descendent of the diesel electric locomotive can be found in the oil well drilling industry, Here, locomotive traction motors and. electric controls have been modified to fit the particular requirements of the drilling industry, One 2400 H.P. diesel electric drilling rig drilled a 24,000 Ft. well in West Texas with an electrical maintenance cost in the order of 7¢ per hour This was a new rig and the costs are less than the average maintenance costs will be for the life of the equipment, Even soy since it took one (1) year to drill this well, this 7¢ per hour has real significance. Electric shovels use a similar type of electrical equipment; they too have shown real savings over the equipment they replaced. Since electric drives have done so well, in other fields, they warrant consideration for use in high horsepower, large capacity trucks.

Jan 1, 1961

By Gy. Deák

The Romanian mining industry, especially salt mining, is going through a restructuring phase taking into account the Environment Acquis of the European Union1. In order to preserve the centuries-old salt mines and to develop new ones, in the same salt rock deposit, the long term stability assessment of the saline complex is very important. This case study refers to the Praid salt mine, which includes old salt mines, with impressive sizes, located above the new mines, with activity in progress, in order to provide the means and solutions for efficient conservation and sustainable exploitation for the salt resources. The DKRControl method and FLAC 3D code were used in order to assess the confidence level for the computed prediction of the stability of the salt mine complex salt.

Jan 1, 2008

By P. I. James, M. R. Baker

Este artículo analiza la nueva producción de cobre a partir de "minerales de desecho" de baja ley usando la tecnología de Blue Planet Strategies DEMET™ (Dynamic Electrode Mining Effluent Treatment, por sus siglas en inglés), que tiene como objetivo salvar la brecha de procesamiento entre la solución débil de lixiviación en operaciones de extracción por solventes/electrowinning (SX/EW), removiendo electroquímicamente los metales a partir de corrientes débiles y a la vez generando productos concentrados en metales objetivo en un análogo funcional de extracción por solventes (SX). Se estudió el tratamiento de la débil solución de lixiviación pregnant (PLS por sus siglas en inglés) y se usó para estimar los impactos económicos y de producción para una hipotética lixiviación en pilas de cobre brownfield y una operación aumentada DEMET usando SX/EW para tratar el "mineral de desecho." Se presenta la remoción de cobre a un 86% de eficiencia en las placas por debajo de 0,1 g/L de cobre con un consumo de energía de 0.55 kWh/lb de cobre y una concentración del producto mayor a 10 g Cu/L. El modelamiento arrojó aproximadamente $2/ lb para la producción total de cobre y costos de tratamiento menores o iguales a $1/lb con un inmediato aumento del margen bruto de operación del 12% para el brownfield incrementado. Se indicó también un aumento de la vida de la mina con un margen bruto promedio de 38% en la producción aumentada de "mineral de desecho" con valores de cobre de $3.25/lb.

Jan 1, 2014

The Australian states of New South Wales (NSW) and Queensland, because of their endowment of black coal resources, dominate the production and export statistics for Australian coal. NSW produced 86 million tonnes of saleable coal in 1994, representing a doubling of output since 1980, or a growth of 5% per annum. Asian demand for thermal and coking coal has, of course, driven this growth in NSW. This high Asian demand is forecast to continue and NSW will seek to secure its share. This paper focuses on some of the issues facing NSW in the future, and in particular, examines some of the major new and proposed mining projects.

Jan 1, 1997

The Gosowong epithermal quartz-adularia vein, in the Halmahera magmatic arc, is a new discovery in an area of primary tropical rain forest with no history of gold mining or mineralization. The newly recognized mineral district also contains a number of other epithermal vein systems, two centres of porphyry Cu-Au mineralization, and a number of argillic and advanced argillic alteration zones that may be related to underlying mineralization. Gosowong was discovered and tested through the application of basic exploration techniques including drainage sampling, soil sampling, trenching, magnetics, IP, and diamond drilling. Lapse time from the initial reconnaissance discovery of a stream sediment anomaly to the release of inferred resource estimates of approximately 1.0m ounces was just over 3 years.

Jan 1, 1997

By J. M. Beck

Mineral property appraisers engaged in eminent domain actions on properties for which mining is the highest and best use must be fully competent in all phases of mineral resource estimation, mine project development, and mine operations (or retain the requisite competent assistance), as well as educated in eminent domain appraisal (USPAP Competency Rule). Failure to ensure such triggers the issue of appraisal competence and demonstrates a flagrant disregard of the myriad code(s) and guidelines to which the appraiser is subject. The cavalier assertion of some vague, undefined “latitude” in the valuation process does not exonerate the appraiser from a disregard of the USPAP Competency Rule. Lack of independence (i.e., “advocacy”) in mineral property appraisal is the usual result of a weak background in mining and/or appraisal theory. While it is readily apparent to those able to recognize it in reports and testimony, judges and juries cannot be expected to detect or recognize purposefully misleading (or even fraudulent) valuation concepts or testimony. Purposeful deception by the appraiser can lead to specious over-compensation of the property owner (thus victimizing the taxpayer); or, a failure to provide appropriate and just compensation to the property owner – yet, the purpose of an eminent domain proceeding is to leave the property owner no richer or poorer as a result of the taking. This paper highlights some of the deceptive practices encountered in litigation settings and raises issues of competency, professional ethics, and the effectiveness of the inherent enforcement capabilities within those institutions awarding professional certifications. INTRODUCTION The practice of eminent domain mineral property appraisal requires (particularly with respect to undeveloped mineral properties) that the appraiser possess the requisite level of competence in all phases of mineral resource estimation, mine project evaluation, mine development, and mine operation (through closure). To the extent the appraiser lacks such competence, it is incumbent on the appraiser not only to divulge this lack of expertise but also to seek competent assistance in the performance of the appraisal. This competence or expertise can only be obtained through a combination of appropriate and relevant technical education and direct mining industry experience. There exist a number of professional certification and/or credentialing authorities that speak to such competency. In a similar manner, eminent domain mineral property appraisal (as the term implies) also requires that the appraiser possess the requisite level of competence in the practice of eminent domain appraisal. This competence or expertise can only be obtained through appropriate and relevant education, direct knowledge of appraisal theory, particularly as it relates to the concept of eminent domain, and licensure.

Jan 1, 2019

By Quansheng Li

Large-scale coal mining will cause environmental problems such as aquifer damage, land excavation and occupation, soil erosion, vegetation damage, and regional landscape damage. The existing coal mine environmental restoration technology is relatively simple, and there is a lack of systematic research on environmental total factors. Based on the mechanism of coal mining damage and the laws of environmental natural succession, the concept of “coal environmental protection mining” is proposed, which combines damage reduction mining and environmental element system restoration. In accordance with the environmental protection principle of “source protection, process damage reduction, and systematic restoration,” a technical system of “coal environmental protection mining” is constructed for the two types of mining damage scenarios: underground mining and open-pit mining. In view of the damage characteristics of underground mining, source environmental protection technology based on optimization of mining process parameters, stability maintenance and damage reduction technology for overlying rock bearing arch shell structure, zoning and time-sharing treatment of surface cracks, and direct drainage irrigation technology for mine water have developed. In accordance with the damage characteristics caused by open-pit mining, land-saving and source reduction damage technology, near-natural stratigraphic reconstruction, topsoil improvement, and environmental storage and utilization technologies for seasonal precipitation have developed. By applying the technology in this paper, the maximum surface settlement value of 12401 working face in Shangwan coal mine was relatively reduced by 25%, the surface cracks have been adjusted from step-type cracks to dynamic small cracks, and since the technical implementation of the Shendong mining area in 2010, the vegetation coverage has increased loss and crushing decreased by 0.06 km2 every year, the environmental restoration period of the dump site was advanced by more than one year, and the vegetation coverage rate increased by 41.78% compared with the background value in the semi-arid area of the victory open-pit coal mine demonstration area. A surface reservoir with a water storage capacity of 400,000 cubic meters has been built, and the seasonal and graded utilization of mine water has been realized. An underground reservoir with a water storage capacity of 1.22 million square meters has been built in the Baorixiler open-pit coal mine.

Jun 25, 2024

By J. Zhai, Z. Yin

"The electrokinetic and flotation behaviors of ilmenite using lead ions as the activator and sodium oleate as the collector were studied. The results of microflotation show that the flotability of ilmenite can be improved by lead ions obviously. The isoelectric point of ilmenite increases from 5.32 to 7.7 after the addition of lead ions because of the adsorption of Pb2+ and Pb(OH)+. The results of zeta potential measurements and the collector adsorption density calculation show that the adsorption of sodium oleate on the ilmenite surface via chemisorptions in addition to electrostatic interactions. Besides, the adsorption density calculation results show that as the addition of lead ions as the activator, the adsorption amounts of collector are greater than those without activation which is in aggrement with the flotation behaviors. INTRODUCTION Ilmenite, as an oxide mineral of formula FeTiO3, is usually used as the main resource of the extraction of titanium (Bulatovic and Wyslouzil, 1999). There are many researches showing that the conventional methods, such as gravity separation, magnetic separation and flotation, do not work efficiently as expected (Mehdilo et al., 2015; Zhu et al., 2011). Nowadays, to produce ilmenite concentration feasibly and efficiently, these separation methods above are combined for a reason that the raw ilmenite ores are characteristic of poor, fine and complicated. Moreover, surface modification, such as surface dissolution method, microwave irradiation and oxidation roasting, is applied to improve the flotability of ilmenite currently (Welham and Llewellyn, 1998; Zhang and Ostrovski, 2002). Generally, fatty acid salts are used as the collector for the flotation of oxide minerals and sodium oleate is usually used as the collector for the flotation of imenite ores (Fuerstenau and Pradip, 2005). The mechanism, such as individual ion electrostatic adsorption, chemical adsorption, ion–molecule dimeric complex adsorption, and the coadsorption of ion and molecule, have not been discussed systematically using sodium oleate as the collector in the flotation of ilmenite (Somasundaran, 1983). Under the activation circumstance using the lead ion as the activator and sodium oleate as the collector, the interaction mechanism seems to be still unclear. In the present study, the interaction mechanism between ilmenite and sodium oleate using lead ion as the activator are studied by microflotation, zeta potential measurements and adsorption density calculation. EXPERIMENTAL Materials and reagents Pure ilmenite minerals were obtained from Panzhihua, Sichuan province, China. The minerals were ground in a porcelain mill with an agate ball. Following that, the prosucts were sieved, and the samples of -0.074+0.038 mm size fraction were used for the microflotation experiments. The results of XRF show that the content of titanium element is 30.58%, showing that the purity of ilmenite is above 90%. On the basis of the results of XRF, it is determined that the purity of ilmenite is very high and meets the needs of microflotation"

Jan 1, 2017

By Gerald A. Zicg

The Sheep Creek project area lies between 15 and 20 miles north of White Sulphur Springs in west central Montana, on the southern flanks of the Little Belt Mountains. The Sheep Creek project is a joint venture in which Cominco American Resources, Inc., has a 50% operating interest and BHP-Utah International, Inc., has a 50% participatory interest. The property consists of over 40,000 acres of leased fee land and lode claims. Modern exploration of the Sheep Creek area began in 1973 and 1974, when Homestake Mining Co. examined the extensive Sheep Creek gossans with soil sampling, trenching, and drilling. Cominco American Inc. began exploration in the area in 1976. Between 1978 and 1985, Anaconda Copper Co., Exxon Minerals Co., and Freeport also conducted exploration programs in the area. In 1985, Cominco completed consolidation of the district, gained BHP-Utah International, Inc., as a joint venture partner, and the joint venture drilled the first significant copper mineralization on the property. Of six bodies of copper mineralization so far located, the best defined are an upper copper zone, which includes a probable resource of 4.5 million metric tonnes grading 2.5% Cu and 0.1 % Co, and a lower copper zone which includes a possible resource of 4.5 million metric tonnes grading 4% Cu. Exploration drilling of the property is in progress.

Jan 1, 1991

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003