Search Documents

By H. Walqui, S. K. Kawatra, C. H. N. Jeltema, T. C. Eisele

"The literature contains many cases where the shape of hydrocyclone efficiency curves vary from the ideal “S” shape. These often appear as changes in slope, or inflections. These inflections can be divided into two categories: “coarse” inflections, which are caused by differences in the density of the minerals being separated, and “fine” inflections, for which there are a number of competing hypotheses concerning their cause. The existing literature addresses either the fine inflection or the coarse inflection, but no studies have reported both types of inflection occurring at once in a single hydrocyclone test. This paper presents hydrocyclone results from both in-plant studies and laboratory experiments that show both coarse and fine inflections. The industrial significance of both types of inflections is discussed. Hydrocyclone efficiency curves show the probability of any given particle reporting to the hydrocyclone underflow as a function of its size. Selectivity functions, S(d), are used to represent the fraction of the feed material in size fraction “d” that reports to the hydrocyclone underflow. Plotting this selectivity function against particle size leads to the standard S-shaped efficiency curve shown in Fig. 1. In the “uncorrected” curve, the tail of the curve does not go through 0%, because a portion of the solids are bypassing classification. This happens as a result of their being carried along by the water, and is most important for the finest particles. The curve can be “corrected” based on the fraction of the feed water that reports to the underflow, represented by the bypass fraction, Rf. The corrected curve then normally passes through 0%, as shown in Fig. 1.The act of correcting the curve shifts the value of the d50 size, which is the size that has an equal probability of reporting to either the overflow or to the underflow. Correcting the curve to account for the bypass fraction makes it easier to compare cyclone performance under conditions that cause the quantity of water in the underflow to change, but that do not alter the actual corrected cut size (d50c).The corrected efficiency curve can be expressed closely by equations such as Plitt (1976):"

Jan 1, 2015

By A. Gungor

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By R. H. Grau, C. D. Taylor, A. L. Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Mine Improvement and New Emergency Response (MINER) Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the National Institute for Occupational Safety and Health (NIOSH) Bruceton Experimental Mine was pressurized using a 1.1-m (42-in.) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

By C. L. Molina

The U.S. Geological Survey (USGS), in cooperation with the Bureau of Land Management (BLM), Geological Survey of Wyoming, and U.S. Bureau of Mines (USBM), will produce an estimate of the amount of available coal in an area about 55 Ian (35 miles) south of Gillette, Wyo., where the Wyodak coal bed is 8-27 m (25-90 ft) thick. Available coal is coal that actually is accessible for development under current regulatory, land-use, and technologic conditions. Local coal-development considerations include roads, ranches, railroads, pipelines, power lines, wildlife and archaeological sites, alluvial valley floors, cemeteries, and the Hilight oil and gas field and gas plant. Some of these considerations would be mitigated so that surface mining may proceed; others presently preclude mining in their vicinity.

Jan 1, 1995

Anomalous geologic or stress conditions ahead of the longwall face can cause great harm to both the individual miner and the mining operation as a whole. The U.S. Bureau of Mines has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of a field effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure, and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration, likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with laboratory measurements.

Jan 1, 1995

By A. Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970's. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator's area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator's hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By D. Malhotra

The effect of some of the reagents, namely hydrocarbon oil, Syntex (sulfated coconut oil surfactant), pine oil, sodium silicate, and lime, used at the Climax mill on the recovery and grade of molybdenite and gangue minerals has been investigated experimentally using factorially designed test approach in the laboratory. The results of the investigation are presented in two dimensional plots. The lower additions of lime (equivalent to a pH of 8 to 8.5) were desirable for maximizing recovery subject to constraints on grade. Higher additions of pine oil improved recovery, but only at the expense of grade. A mathematical model of the objectives of an operating plant was formulated and optimum reagent conditions obtained.

Jan 1, 1977

By Emily Sarver, Cigdem Keles, Jonathan Gonzalez

The study re-examines respirable coal mine dust samples using scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). It finds that SEM tends to overpredict the abundance of dust from rock strata and underpredict coal content, possibly due to coal-mineral microagglomerates (MAGs). The findings suggest that MAGs could be valuable in improving dust controls in mines.

Feb 10, 2022

By J. Brooks

The use and application of shotcrete for ground support in the Asia Pacific Region is as diverse as the countries that make up this region. This paper will attempt to describe the many methods used on selected projects within that region. The project description(s) will include project logistics, equipment, mix design, products and application methods utilized along with specifications and performance results (where available). The author will attempt to reach a conclusive opinion on the success, or nonsuccess, of the various shotcrete methods employed and the development of shotcrete within the Asia Pacific Region.

Jan 1, 1999

By Terry O. Arney

This paper is a description of the digital Data Acquisition and control System that is installed at Cities Service's Pinto Valley Concentrator. Pinto Valley Concentrator ? The Pinto Valley Concentrator (5, 41 is located approximately seven miles west of the town of Miami, Arizona. The Concentrator is situated south of the open pit mine and was designed to process 40,000 tons of ore per day with an average grade of .45% copper. The comminution process consists of primary, secondary, and tertiary crushing, and single-stage closed-circuit grinding 161. Concentration of the copper sulfides is by means of froth flotation. Concentrates are transferred to the Inspiration Consolidated Copper Company smelter in Miami, Arizona through a slurry pipeline.

Jan 1, 1976

By D. Boreck

The Bureau of Mines is conducting research on the feasibility of incorporating in situ stope leaching into active underground metal mines. Stope leaching, a modified in situ leaching technique, proposes to recover metals by leaching fragmented ore in existing underground openings and collecting and processing the metal-bearing solution to recover the valuable metals. If leaching solutions escape from the stope, either through geologic discontinuities or highly permeable zones in the rock, valuable metals dissolved in the solution may be lost. Escaping solutions may also contaminate ground waters. Consequently, in fractured rock, the characteristics of the fractures in the vicinity of the leaching stope must be understood before introducing actual leach solutions into the stope. Effectively characterizing a rock mass requires the integration of several disciplines including structural geology, borehole geophysics, hydrology, geochemistry, and mining engineering. This paper will focus on the general geologic and geophysical techniques that can be used to characterize the rock mass at an underground simulated stope leaching site. The results of several geophysical logging methods, tested at the site, are compared to the geologic core descriptions. Then, the? effectiveness of the different geophysical techniques in delineating fracture zones will be assessed. Knowledge gained through the geologic and geophysical analyses can be used to supplement results from hydrologic testing. This information can also be utilized in designing blast patterns and developing strategies for controlling or blocking movement of escaping leach solutions.

Jan 1, 1991

By K. A. Wheeler

To evaluate the effects on groundwater of a proposed in-pit disposal operation at an east Texas lignite mine, the local geologic, hydrogeologic, and geochemical features were thoroughly characterized. Resultant data were used in a flow and transport model (SWIFT) to simulate migration of the ash leachate. Computer simulations indicate that the leachate plume will travel 61-152 meters from the disposal area in 100 years after resaturation of the spoils. A 61-meter buffer zone of mine spoils without ash will surround the disposal area. The proposed landfill operation received regulatory approval and is currently operating as a Class 2 non-hazardous landfill.

Jan 1, 1994

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

By M. S. Prasad

This paper presents the process methods of beneficiating various copper-cobalt and copper-zinc ores mined by Gecamines in Zaire. Geology and mineralization of both sedimentary and vein type deposits are described with special emphasis on the production of oxide, dolomitic and sulfide concentrates. Description of different types of concentrators and their treatment methods are discussed for the production of sulfide, oxide and dolomitic concentrates. Production of concentrates, their consumption and stocks are briefly reviewed. Modernization of the concentrators with substantial investments on grinding, classification, flotation methods and tailings treatments are also discussed to improve the metallurgical efficiency of the concentrators with a view to improve the production of concentrates both qualitatively and quantitatively.

Jan 1, 1990

By R. Thorpe, M. Dosbaba, A. Kopriva, A. Niiranen, J. Ruokanen

"Automated Mineralogy (AM) is an important diagnostic tool in flotation plants as it adds ore and particle mineralogical properties to traditional mass and chemical data. AM is used in project development, for future ore studies and for diagnosing concentrator operations. With the exception of operations who own central laboratory or on-site systems, the use of AM is often limited to the analysis of a comparatively small set of samples. Metrix Plant Technologies has partnered with TESCAN to integrate TIMA AM technology into the implementation of Performance Assessment Campaigns (PAC). Routine daily composite samples from the mill are analysed mineralogically on a size-by-size basis over several weeks. All the relevant metallurgical, process control and mineralogical data is combined into a single large database for mass balancing and interactive examination. This paper describes the implementation and results of a PAC at the Agnico Eagle Kittilä gold mine in Finland. Although challenging, the addition of mineralogical data as dependent variables in multivariate analysis leads to a much deeper understanding of the root cause effect of events driving the flotation performance. INTRODUCTION TO STUDY The Kittilä mine, owned by Agnico Eagle, is Europe’s largest primary gold mine, with annual production of approximately 180,000 Oz. The operation is located in Lapland in northern Finland, and is currently expected to operate until 2035. The location of the operation is shown in Figure 1. Historically, the mine was an open pit, although in recent years ore is sourced solely from underground operations. The processing plant features crushing and grinding, followed by carbon flotation and sulphide flotation. Carbon concentrate is a waste stream, and sulphide concentrate reports to pressure oxidation (autoclave) and CIL circuits for gold extraction. The final flowsheet is shown in Figure 2. Following commissioning in late 2008, the operation achieved commercial production on May 1st 2009. Gold recovery in flotation gradually increased to a 92-96% range at a throughput of ~3500-4000 tonnes per day. In late 2014, the operation commissioned a plant expansion to ~5000 tonnes per day. Following a commissioning period, the operation stabilised with recoveries in a 90-94% range, which over any given period was determined to be ~2% lower with statistical significance. The trends from start-up of gold recovery in flotation and throughput are shown as follows in Figure 3. In early 2016, Agnico Eagle Kittilä mine, along with Agnico Eagle Technical Services (AETS) partnered with Metrix Plant Technologies and TESCAN, to perform a Performance Assessment Campaign (PAC) at Kittilä, involving automated mineralogy on five key streams at Kittilä on 40 days selected from a 50 day period between February 15th and April 4th 2016, when plant operations were stable. In addition to the mineralogical data, metallurgical and operational data were pooled into a single, powerful database to explore opportunities for the operation to improve recovery in a sustained manner, ideally to the levels pre-expansion."

Jan 1, 2017

By E. A. Twichell

An entirely new concept in the effective utilization of magnetic, energy has resulted in a major break-through in the design of magnetic separation equipment. One of the first applications of this concept has resulted in the development of a Permanent Magnetic Wet Drum Separator with strength .and operating characteristics equal to Electro Wet Drum Separators. Prior to this development when strength and adjustability were required, electro wet drums were specified even with all their drawbacks. The electros, by nature, are subject to coil failure or burnout, over-heating and loss of strength, high power consumption and generally high maintenance. Now the high strength and the adjustability, formerly the exclusive property of electros, has been engineered into permanent wet drum separators. These units combine maximum field strength in the separation zone with strength adjustment to suit changing conditions. Adjustment can be effected while the drum is in operation without stopping either the feed or the drum.

Jan 1, 1967

By Nelson Alonso Portal Ravichaua, Melissa Esther Mendoza Tirado, Raúl Arévalo Saavedra

This study analyzes the implementation of an integrated strategy for environmental education and community awareness in Cajamarca, Peru—an Andean region affected by climate variability and the public perception of miningrelated water shortages. In collaboration with the Interactive Water and Earth Museum and the Newmont ALAC Foundation, three-month campaigns were conducted in schools and local communities. Key topics included the water cycle, climate change, and water availability, linked to urban infrastructure projects that improved flow rates through strategically located tubular wells tapping underground aquifers. The initiative addressed the challenge of communication in a context where mining is often blamed for scarcity, fostering scientific understanding of contributing factors. The study highlights how science-based outreach and institutional collaboration can strengthen resilience and promote sustainable water stewardship in mining-influenced regions.

Feb 22, 2026

By J. A. Hartlage

Four years ago, Ashland Chemical Company introduced a new copper solvent extraction reagent for hydrometallurgical utilization. The reagent, an alkylated 8-hydroxyquinoline, is called Kelex 100 ®(1). Since the time of introduction, the reagent has been investigated by several workers for its solvent extraction utility in the separation and purification of transition metals (2-7). In the following text, those factors which are essential to the optimum performance of Kelex 100 on concentrated copper solutions will be discussed. To date, the reagent has been found useful in active concentrations of from 1 to 20% Kelex 100. In order to achieve the best performance for Kelex 100, it has been found that a phase modifier is essential. Various alcohols and phenols have been evaluated in order to improve phase performance and stripping characteristics of the solvent system. Modifiers and diluents are especially important when solvent activities between 3 and 20% Kelex 100 are employed. A 15% Kelex 100 solvent, for example, containing 15% nonyl phenol in Escaid 100 (Exxon) can be utilized to remove greater than 33 grams per liter of copper from an aqueous feed without interstage neutralization, and in the same process scheme the reagent can be stripped to less than 1 gram per liter barren organic producing a pregnant electrolyte containing greater than 40 grams per liter copper and less than 120 grams per liter sulphuric acid. The unusually efficient stripping of Kelex is accomplished by protenation of the extractive molecule during the stripping process.

Jan 1, 1974

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

By J. L. Workman

The stability of spoil and highwall slopes are important to successful strip mining. This paper discusses soil parameters of importance in stability analysis. The common mechanisms of spoil failure are discussed. Modes of highwall failure are also outlined. The importance of water to stability is presented. Dragline mining methods most suited to creating spoil and highwall profiles that address stability needs are provided. It is concluded that groundwater and surface runoff must be well controlled, and that it will often be necessary to modify spoil and highwall configurations to achieve a stable overall slope angle.

Jan 1, 1996