Search Documents

By Heiner J. Sander

Stanford University operates the National Research Facility which is located at the Stanford Linear Accelerator Center (SLAC) in Menlo Park, California. In order to improve and allow for enhanced experiments, the current facilities required expansion. A1500 foot long tunnel (20 ft wide by 21 ft high) and a 220 foot long underground cavern (49 ft wide by 32 ft high) were excavated through the Ladera Sandstone formation which is an intermediate geo-material with week rock properties. The overburden between surface and crown of the structures varies from 10 to 80 feet. The underground structures were excavated according to the principles of the NATM (New Austrian Tunnel Method). This paper addresses the challenges that were encountered during the construction phase of the project and how construction issues were resolved mutually by the owner, engineer and contractor. The implementation of geotechnical instrumentation, recorded data and interpretations, soil conditions and behavior encountered during construction are also presented.

Jan 1, 2008

By Ray L. Tobie, Douglas E. Julin

GENERAL DESCRIPTION Block caving is a distinct caving method applied mostly to large, massive, ore bodies because of its in¬herent low cost and high production capabilities. Areas of sufficient size are removed by undercutting so that the mass above will cave naturally. Drawing of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling. When properly applied, block caving results in a lower mining cost per ton than any other under¬ground method. There are three distinct forms: (1) dividing the horizontal area into rectangular or preferably square or nearly square blocks, drawing evenly over the entire area to maintain an approximately horizontal plane of con¬tact between broken ore and caved capping; (2) divid¬ing the horizontal area into panels across the ore body, retreating by undercutting manageable areas from one end of the panel to the other and maintaining an in¬clined plane of contact between the broken ore and caved capping (thus the name panel caving); and (3) no division of horizontal area of the ore body into defi¬nite blocks or panels (this is termed mass caving). Undercutting may be from wall to wall, retreating from one end of the ore body to the other, maintaining an inclined plane of contact between the broken ore and caved capping. The total active caved area is deter¬mined by the size of block that will not produce undue stress on workings below the undercutting level and by total production requirements. This type of operation is also referred to as panel caving at some properties. SUITABLE ORE BODIES Block caving in its various forms is applicable to deposits of various shapes and ores of various strengths. Its success is governed by rigid requirements and limi¬tations. In unsuitable deposits or where improperly em¬ployed, the loss of ore may exceed that of any other mining method. Good planning, systematic work pro¬cedures, careful supervision, and good judgment con¬tribute to its success. Ore Characteristics Included as a necessary characteristic in an ore body suited to a successful block-caving operation is a proper fracture pattern. Ore hardness should be another gov¬erning factor, and the toughness or softness of the ore should be considered. There must be sufficient horizon¬tal area available for expansion of the undercut, if neces¬sary, to start the caving process. Large, massive, ore bodies usually meet these conditions. Veinlike deposits must be wide and dip rather steeply to conform to the block-caving limitations. The capping must be of such a nature as to cave when the underlying ore is being removed since the weight of the overburden aids in crushing the ore. The most favorable capping character¬istic is that it breaks into coarse pieces and resists attrition as the block is drawn. Soft capping, by breaking into fine pieces and sifting into the ore or channeling through the ore to the drawpoints, can seriously dilute the ore and hinder the extraction of clean ore from the blocks. Types of Ore In block caving, a fairly uniform distribution of val¬ues in the ore is necessary. Grade values may range from low grade to high grade, but most often the sys¬tem is applied to low-grade ores. Wide veins, thick beds, or massive deposits of homogeneous ore overlain by ground which will cave constitute suitable ore bodies. The ore must be such that it can be supported while blocks are being developed and undercut but breaks up readily when caved. Some applications include porphyry copper, disseminated molybdenite, hematite in the Lake Superior iron district, limonite deposits in northern Spain, the diamond mines of South Africa, asbestos and nickel in Canada, and massive magnetite in Pennsylvania. Size and Shape Outline of the ore body should be fairly regular, and the sides of the ore body should dip steeply. It may not be economical to mine small portions of ore extending into the walls of the deposit, and low-grade inclusions in the ore cannot be left unmined. Some dilution of the ore, as mining progresses, by low-grade or barren cap¬ping is inevitable and, unavoidably, some clean ore is left between drawpoints. Determining Cavability The use of rock mechanics is sometimes advantageous in helping to determine the cavability of an ore deposit. The US Bureau of Mines has information and testing ability which can assist in determining the cavability of ore types. Several competent consulting orga¬nizations knowledgeable in rock mechanics can also as¬sist in evaluating the cavability of an ore body. Some recent work has been done to better define the cavability index of various ore bodies; an example of how this was determined is discussed by McMahon and Kendrick (1969). The intensity of the fracture pattern is a critical parameter to be analyzed. The question to be answered is, "How intense must the fracture pattern be?" Table 1 is a tabulation of the size of rock fragments that appear at the drawpoint of various block-cave mines around the world. These are indicative of the fracture-pattern spac¬ing and, as can be seen, they vary substantially from the almost sandy material at the Mather mine to fairly sizable blocks at the Grace mine. Several sets of fractures are essential to promote good caving. Ideally, two vertical sets at nearly right angles to each other and a third set nearly horizontal are required to insure a good caving ore body. Since initial caving of an ore mass is almost always by the action of gravity acting on these planes of weakness, it is doubtful

Jan 1, 1982

By D. A. Lindsey

Gravel lithology affects the quality of aggregate because different rock types in gravel have different physical and chemical properties. The lithologic composition of alluvial gravel reflects the composition of its source terrane and the variable effects of weathering and transport on each rock type. This report discusses lithologic controls on aggregate quality in the mountain-front environment of the Colorado Front Range. Lithologic controls on aggregate quality of gravels were evaluated using pebble count data. Gravel lithology along the Front Range shows both temporal and regional variation. The principal variable in gravel lithology is quartz plus quartzite, of which quartzite is commonly more abundant. Large quantities of metaquartzite derived from the mountain front southwest of Boulder, Colo., were dispersed northeastward during deposition of the oldest Front Range gravels. Average quartz plus quartzite is greatest in the oldest gravels. Aggregate quality is probably enhanced by large quantities of quartzite. Abundant volcanic rocks in gravel may enhance aggregate quantity, but such occurrences are local in extent. Abundant sedimentary rocks in gravel, mainly sandstone near the mountain front, may decrease aggregate quality.

Jan 1, 2002

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By Pat C. Hautala, J. R. Hoskins

This is a new era for the minerals industry. Never before has there been more need for effective communication. So said Robert Anderson, chairman and chief executive officer of Hanna Mining Co. He was speaking to the American Mining Congress's Communication Workshop. The question is whether there is enough industry concern to meet the challenge. Anderson observed that increased workshop attendance, in continuing tough times, reflects the industry's concern for communication. But, why were students, faculty, engineers, supervisors, and managers not at the conference? Communication applies to every manager, Anderson said. But he was the only operating manager present. And only one company sent operating supervisors. The remaining conference participants were public relations personnel, generally with nonmining backgrounds. And the program dealt mostly with public relations issues. Role of Communication in the Minerals Industry. It is well known that the minerals industry faces economic, political, and social problems. Economic shifts and foreign competition have created an international minerals industry and an international marketplace. This, in turn, calls for worldwide communication. Other factors effecting communication are: • Governmental protectionism as well as regulatory reforms call for increased interaction with governing officials. • Changing social values have created environmental issues and anti-industry attitudes. This intensifies the need for improved public relations. • Traditional work values are shifting towards self-actualization and humanistic movements. The work force is better educated and more informed. Employees demand more satisfaction, equality, and job autonomy. • The mining industry's task of managing its human resources is complicated by layoffs, job uncertainties, and bleak outlooks concerning employee morale and motivation. Technology and Information for a New Era As noted, this is a new communications era, one propelled by technology and information. Technology has led to reduced demand for raw materials by developing substitutes. Copper demand, for example, will never fully recover. Copper cables are replaced by fiberoptics; copper transmission lines, with aluminum. Technology has shifted the US from traditional to high tech and service industries. The speed, frequency, and scope of information transmission have greatly increased. But the most significant characteristic of this information is not the pace of advancing technology. It is the dramatic increase in the importance and frequency of our personal transactions. Knowledge has replaced raw materials and capital as the strategic resource. Information has replaced energy as the transforming resource. And the game against nature has become an interpersonal game (D. Bell, Post-industrial society, Physics Today, '76). In Megatrends, John Naisbitt says that information will soon double every 20 months. So, professionals will become "information workers." And communication will be the life channel of the information age. Thomas Wolfe said you can't go home again. Hanna Anderson said we are, indeed, facing a new day. It will never again be "business as usual." We must move into the information age with the rest of society. We cannot trust that the world will continue to rely on our products. Nor can we place the responsibility and control for problems and solutions outside the minerals industry. Improved communication is not a panacea. But, Anderson said, it is critical to the minerals industry. What is Communication? The word communication is overused. It is applied to every aspect of our lives. Satirist Tom Lehrer got sick of hearing about the need to communicate. He said, "It seems to me that if someone is having all that trouble communicating, the very least he can do is shut up!" Obviously, we cannot follow that advice (though we might wish that some others would do so). Communication is always going on. It is inevitable. Yet we have many misconceptions about com-

Jan 1, 1985

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, the National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By B. K. Blashich

In responding to mine fires and explosions, accurate and timely analysis of the mine atmosphere is critical in making decisions regarding firefighting, mine rescue and mine recovery operations. For many years instantaneous analyses were available to rescue workers using handheld or portable gas detection equipment, including infrared, electrochemical, or catalytic measuring devices for a limited number of specific gases such as oxygen, methane, carbon monoxide and carbon dioxide. Instantaneous sensing technology is not available for all gases, such as nitrogen and hydrocarbons, found in a mine fire atmosphere and cross-sensitivity can be a problem with this technology. For these reasons, air samples are collected for injection into a gas chromatograph for a complete and accurate analysis for all gases including oxygen, nitrogen, methane, carbon monoxide and carbon dioxide, as well as ?fire gases? such as hydrogen, ethylene, ethane, and acetylene. This method requires additional time for transporting the samples to the laboratory near the mine, as well as an instrument operator to inject the samples for analysis. The use of a portable micro gas chromatograph with a continuous and automatic injection system has been implemented by the Mine Safety and Health Administration (MSHA) during mine recovery operations. The device directly samples the mine atmosphere from an underground location every twelve minutes and automatically analyzes the samples for all of the mine fire gases. The portable unit utilizes micro technology and the operating software has been modified to perform the calculation of sample results in and Excel® spreadsheet without user interaction. This paper describes the micro gas chromatograph system and its use at a recent mine recovery operation. The automated remote operation of the micro gas chromatograph has been shown to be a good alternative to infrared and electrochemical sensors used for mine atmosphere analysis.

Jan 1, 2009

By CHRISTOPHER D. HEBERT, SCOTT W. HOFFMAN

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2019

By V. McLemore, A. Fakhimi, K. Donahue, D. Sweeney, V. Viterbo

In order to evaluate the relationships between weathering and durability and strength of rock samples from the Goathill North rock pile at the Molycorp Questa mine, NM, we conducted slake durability and point load tests. Slake durability index (ID2) values ranged from 84 to 98%. Point load strength index (Is50) averaged for all rock units ranged from 1.1 to 5.7 MPa. Results show a slight positive trend between ID2 and paste pH. Two populations of data are distinguishable when ID2 is plotted versus the percentages of chlorite, illite and internal friction angle. In general, Is50 values increase toward the interior of the rock pile. Preliminary conclusions indicate that the durability and strength of the rock pile material generally increase toward the interior of the rock pile. Pre-rock pile alteration and post-rock pile weathering history have affected the durability of the GHN rock pile samples.

Jan 1, 2007

By R. Zunich, E. Rybinski, M. Grondin, B. Flintoff

It is uncommon these days to read a business magazine or newspaper without finding a reference to Knowledge Management (KM), and its critical importance to corporate success. One definition of KM is: “getting the right knowledge to the right people at the right time and helping them to put information into action in such ways that strive to improve organizational performance.” In the minerals processing industry we could assert that we have been practicing this for years through effective operator training. In most cases we would probably be wrong. Training has certainly filled the need of addressing safety and basic operational issues, but we must collectively focus on education (learning), and the difference, as measured in outcomes, is not at all subtle. This paper briefly examines the history of training and education in the mining industry, and looks in more detail at the impact of one company’s approach to empower its workforce, while keeping the ultimate goal clearly in mind: “The great end of knowledge is not knowledge, but action.” (T.H. Huxley)

Jan 1, 2001

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several stages —basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP increased by 3.5 percent from 2004 to 2005. The nominal GDP was $12.5 trillion at the end of 2005. Housing starts were up by more than 5 percent for the year, and the unemployment rate decreased to 5.1 percent in 2005 from 5.5 percent in 2004. The prime interest rate increased from 5.25 percent at the beginning of the year to 7.25 percent at the end of the year. The value of minerals mined in the United States in 2005 rose significantly because of increased unit prices for some metals —particularly molybdenum — and significantly increased production for some industrial minerals, mainly cement, construction sand and gravel, and crushed stone.

Jan 1, 2006

By J. Warmbrodt, D. Apel, D. Nutakor, L. Grayson, M. Hilgers

MinerSIM is an augmented reality system with integrated hypermedia that is suitable for training underground miners in the basics of using a jackleg drill to install rock bolts. While statistical evidence shows that rock bolting with such a drill has an inherent level of risk, it is conjectured that this can be mediated with adequate safety training outside of the actual mine environment using a variety of educational media including interactive three-dimensional images, games, animations, and videos to describe the mechanics of rock bolting and its principles. Ultimately, trainees will install rock bolts in an immersive environment mixed with real and virtual images generated via a gaming graphics engine. This paper will discuss considerations, implementation issues, and evaluation methodologies of the MinerSIM system.

Jan 1, 2007

By R. Owen, T. Canty, C. Marks

The industrial vision system provides on-line 2D particle size analysis for aggregate slurries in both the overflow and underflow of hydrocyclones. This paper covers required vision system features allowing CCD cameras to function in the harsh environment of a mine milling area. The study conducted demonstrates the system’s capacity to obtain particle size distributions for controlling hydrocyclonic separators. The particle size distribution is obtained within seconds and immediately updated to allow for process adjustments. Results are then provided as a graphical computer generated display or output as a 4-20mA current loop for process control. The primary use of the vision system is in classifying particles in cyclone overflows which are often a few microns in size. Typical size information for actual mine slurry samples are presented and possible control schemes discussed.

Jan 1, 2002

By J. W. Davis

In the last few years major industrial companies have begun to realize the importance of Reliability as an enterprise strategy that, properly implemented, will improve financial performance. Typical results of an effective Enterprise Reliability Strategy include a 20% -50% reduction in maintenance cost accompanied by a 5% - 10%increase in real production capacity, with no capital investment in production equipment. One factor fueling the race to acquire and implement enterprise reliability is the pressure for companies to be increasingly cost-effective and competitive in global markets. In a recent study, Asset Productivity: The Next Wave, the Boston Consulting Group (BCG)stated that, “In order to compete for funds, companies must offer investor returns that are competitive with other opportunities. Alternative investments such as dot-com and others with non-traditional business models have raised the bar.” (APDF version of the study can be downloaded at www.bcg.com). BCG views asset productivity as the most powerful mechanism for increasing shareholder return. The author believes that the most effective way to increase Fixed Asset Productivity is to maximize asset utilization by increasing the Reliability of the Assets and the associated processes. Developing and implementing an ERS requires significant effort and knowledge. Most companies have difficulty finding a sufficient supply of these valuable commodities to implement an ERS Program internally. Many companies also struggle with figuring out how to get started and what direction to proceed.

Jan 1, 2003

By Victor Romero, Steve Redmond

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2011

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy

By B. R. Stewart, L. W. Zelazny

The exclusion of coal fly ash from regulation as a hazardous waste has led to increased interest in returning ash to the coalfields for co-disposal. A multi-year column study used coal refuse with high potential acidity (4% total-S), and two alkaline ashes in various bulk-blends. The unamended refuse acidified rapidly, producing acidic (pH 1.7) leachates, high in dissolved metals. Treatments blended with sufficiently high amounts (20 to 33%) of alkaline ash produced alkaline (pH >8.4) leachates with low metal levels, while lower ash blending rates acidified over time to produce metalliferous leachates. Examination of solid materials indicated that pyrite oxidation was occurring to some extent in all treatments. A regression equation (r2 = 0.95) was developed to estimate time to net acid release for mixtures of these materials. Ash alkalinity and refuse potential acidity must be balanced to insure water quality for co-disposal environments, or the ash materials should be isolated away from acidic drainage waters.

Feb 24, 1997