Search Documents

A kinetic model for leaching of various metals with different lixiviants in a batch system has been developed. Material balances for reactants and products at the solid/liquid interface were formulated and solutions to these balances were obtained in view of practical conditions. Special emphasis has been given to examine mixed controlled reaction systems where both heterogenous reaction and mass transfer play important role on the overall rate expression. The resulting kinetic expressions for either powder or rotating disc are discussed in light of experimental findings for various metals. Examples of the metal dissolution systems considered in this study include cobalt, nickel, copper and gold in acid, cyanide or ammoniacal solutions.

Jan 1, 1992

By G. S. Austin

New Mexico produced 83% of domestic potash and 27% of domestic consumption in 1992. The potash industry of New Mexico produces sylvite (KCI), langbeinite (K2SO4-2Mg(SO4)2), and artificial K2SO4. Average sylvite grade in New Mexico today is about 14%. The average grade of langbeinite is 8-10% Kp. Commercial potash occurs in the middle or McNutt Member of the Salado Formation (Upper Permian Ochoan Series). The 120-m-thick McNutt Member dips about 1° east and contains 11 of 12 potential ore zones in the Salado. The mineralogy and proportion of clay minerals, up to 7% of the ore, influence optimum milling procedures and ore grade cutoff.

Jan 1, 1994

By R. E. Scheffel

In February, 1976, Ranchers Exploration and Development Corporation obtained an option from Foote Minerals, Inc., to evaluate reprocessing of two uranium tailing piles. Foote received ownership of the Naturita and Durango tailing piles in 1967 through the purchase of Vanadium Corporation of America. The option was exercised in November, 1976, after initial testwork proved that a viable extraction technique existed. Preparation for production at Naturita began immediately with engineering and en¬vironmental permitting proceeding simultaneously. Production began in December, 1977, just 22 months after acquisition of the property and-was completed 17 months later.

Jan 1, 1981

By Boyd Eisenbraun, Dennis Murr, Milton Rojas

Approximately since 1925, the phenomena of grinding and classification of minerals with screens have been studied. In the U.S. iron ore mining operations located in the so-called “Mesabi Iron range,” magnetite processing plants have made progress in the application of high-frequency screens that have allowed them to process low-grade Taconite ores and successfully achieve the economic benefit of these minerals. In the particular case of magnetite minerals disseminated in the siliceous matrix, the main objective is to reduce the generation of particles called “middlings” with high silica contents. Commonly the primary challenge of the metallurgical task is to achieve high recoveries and iron concentrates with low impurities. To achieve this, several studies and industrial applications have shown success in this regard and not only in iron ores, but also in other minerals around the world. The study described in this paper attempts to describe some key aspects that helped develop an effective solution and list the benefits associated with this modern process design by using industry-proven technologies for minerals in Chile that have similar characteristics to the minerals of the iron belt in the United States.

Feb 1, 2025

By H. K. Lin

Elemental sulfur is founded to be the predominant sulfur-containing species in a leaching residue resulting from ferric chloride leaching, under given conditions, of a chalcopyrite concentrate. The mineralogical study of the leaching residue which consists of 52% elemental sulfur reveals that the sulfur formed at the end of leaching process is in the form of discrete crystal rather than coating film. Flotation has been applied to recover the sulfur successfully using xanthate as a collector. Dispersants arc needed to prevent the mechanical entrapment of silicate and quartz by sulfur. Very high recovery of sulfur with satisfactory grades can be achieved with a relatively simple notation scheme.

Jan 1, 1991

By M. D. Bishop

Early solvent extraction circuits in the uranium industry utilized bona fide kerosenes as diluents for extractant chemicals. These kerosenes were used successfully in the uranium industry; however, at least one plant was destroyed by fire resulting from the use of a low flash point kerosene. Although the term "kerosene" is used throughout the solvent extraction industry, the authors have been unable to find any use of kerosene in copper solvent extraction circuits. A term that is occasionally used with reference to diluents is "metallurgical kerosene." Such a term is unrecognizable in the petroleum industry. Kerosene [or kerosine] is a flammable hydrocarbon mixture that is less volatile than gasoline. It is produced for combustion purposes and may have variable compositions of organic compounds including alkanes, alkenes, alkines, and aromatics. Diluents are constant composition hydrocarbon mixtures developed specifically for use in solvent extraction processes. These products usually have much lower vapor pressures and higher flash points than kerosene. In solvent extraction systems, they typically comprise 70 to 95 v/o percent of the circuit organic. The primary purpose of the diluent is to adjust the extractant concentration to the working range of the operation. The diluent and extractant must be completely soluble or miscible with each other. Secondary diluent effects are to promote transfer kinetics, optimize phase disengagement, and minimize both organic in aqueous and aqueous in organic entrainment.

Jan 1, 1996

By B. Waterman, D. Ramey, L. Schlink

"Water is a primary commodity for most industrial processes. It has become a global focus in light of climate change and population growth. Reuse of process water has two major benefits - minimize the amount of fresh water added now and minimize the amount of discharge water that requires treatment later.Mining and mine product processing has its share of reused water. For example, reclaim water from a tailings impoundment, overflow from thickeners and leach solution to raffinate and back again all demonstrate the use and reuse of water in mining circuits. Eventually, a mine reduces production or ceases operations completely, eliminating the option to reuse the impacted water and, thus, requires treatment of the remaining water.Current methods of water treatment remove the impacts, providing clean water for discharge, but leaves behind a concentrated waste that requires further treatment or disposal of a hazardous waste. Freeport- McMoRan is currently testing three water treatment technologies specific for sulfate and/or metal removal from mine impacted water with the approach of transformation not concentration. These technologies provide clean water for alternative use while creating byproducts that could be marketable, or disposed as a nonhazardous material, thereby reducing the cost and longterm liability of disposal.The selection of a water treatment process is site-specific. The volume of water, contaminant to be removed, disposal options, length of time for treatment, location of plant and reagents and discharge requirements are some of the factors that need to be considered when selecting a water treatment process. Common water treatment technologies for mine impacted water consist of low- or high-density sludge (LDS/ HDS), reverse osmosis (RO) and evaporative technologies. In addition to operating costs, these processes require additional handling of the concentrated sludge or brine. Advanced water treatment technologies include ion exchange, solvent extraction and metals precipitation with or without the aid of a biological system. Some of the more complex systems have a series of unit operations to achieve required discharge regulations."

Jan 1, 2014

By L. K. Holder

The White King / Lucky Lass Superfund site consists of two former uranium mines in south-central Oregon. The remedy included consolidating two large mining overburden stockpiles that contained low levels of radioactivity and heavy metals by moving over 700,000 cubic yards of material and then capping the combined stockpile. An innovative armored cap design was used to minimize the stockpile footprint and thereby prevent disturbing existing wetlands. In addition, the stockpile was designed to merge into the surrounding topography. The remedy also included stream restoration and development of new wetlands. The stream was returned to its pre-mining channel, with the addition of hydraulic features to create new wetlands. The wetlands have greatly enhanced the ecological value of the remedy and the site.

Feb 23, 2014

By Magnus Ericsson

The unexpectedly quick recovery in world crude steel production in the second half of 2009 was due almost entirely to increased production in China that began in late 2008. Previous peaks in monthly production in China were matched by April 2009. The rest of the world had still not reached pre-crisis production rates by May 2010. Chinese production drives growth, but there has been some growth in most other larger crude steel producing countries as well, compared to production in 2009. If the production rate of the first four months of 2010 continues, the total output of crude steel in 2010 will be somewhere around 1,410 Mt (1.5 billion st), the same as in the record year of 2007.

Jan 1, 2010

By Charles E. Michener

This paper deals with the occurrence of basic and ultrabasic rocks and their relationship in space and time to major structures of the earth. In order to introduce the paper properly, I must go back a little and try to put the subject in perspective. In the brief time that geology has been a scientific occupation, ore deposits have been grouped and classified in various ways depending on the theories that happened to be popular at the time. Some of the early scientists said that ore came from fire, other schools argued that ore originated from water. Then came the lateral secretionists and in later years the hydrothermalists led by the Lindgren school and the latter has largely been accepted as the modern concept of ore deposits. It now seems apparent that the hydrothermal school is being seriously challenged by other schools of thought. It also seems that we have reached the point where we should be willing to admit that we do not really know in most cases how the ore got to its present position. However, for practical purposes, we can classify ore deposits as to the environment in which they do occur. This is not difficult and gives the field geologist and the mining engineer something to work with and to believe in, and it gives them a basis for carrying out their field work. On the screen, Figure 1, there is a classification of ore deposits based on the environment. Under each classification is listed the more prominent metals which are characteristic of that

Jan 1, 1971

By Daniel E. Walsh

A pilot scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2"), crushed ore from Ester Dome, Alaska. 9.04 tonnes (9.94 tons) of crushed ore were sampled and processed through a Pan-American jig -Wifley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/tonne (22.4 oz/ton). The feed grade to the plant was calculated at 1.71 g/tonne (0.050z/ton). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/tonne (0.042), 1.30 g/tonne (0.038), and 5.47 g/tonne (0.16 oz/ton) respectively. Significant, coarse, free milling gold values were shown to remain in the jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1991

By J. W. Hawkins, K. B. C. Brady, M. W. Smith

The Pennsylvania Department of Environmental Protection (PaDEP) has been issuing surface mining permits since 1984 that authorize remining in areas that will affect preexisting pollutional discharges. These permits require the mine operator to employ best management practices to reduce pollution loading from abandoned mine discharges. A total of 110 completed mining operations with 233 discharges were evaluated to determine the impact to water quality. Overall, acid loading from these discharges was reduced by 7, 200 kg (15, 900 lbs) per day or 61%. Metal loadings were also reduced. For acidity, 49% of discharges improved or were eliminated, 52% showed no significant change and fewer than 1 % got worse. Loading reductions resulted from a combination of reduced concentrations and lower flows.

Jan 1, 2003

By Celeste Powell

Liquid carbon dioxide can be used as a replacement for organic solvents in the extraction of anionic PGM complexes from an aqueous phase. This can be achieved only if highly carbon dioxide-soluble chelating agents are developed because conventional chelating agent-metal complexes, such as trioctylamine-gold chloride, are not soluble in liquid carbon dioxide (although trioctylamine is CO,-soluble). Our novel CO,-soluble chelating agents have a fluorinated tail and a conventional amine head group. Both the chelating agent and the chelating agent-metal complex are soluble at ambient temperature at pressures between 7-35 MPa. Equilibrium constants in the 105 range have been measured (in Freon 113, a low pressure screening liquid for carbon dioxide), indicating that these compounds will strongly bind the metal chloride. For example, 93% of Pt-chloride was extracted into Freon 113 using a 3.5:1I ratio of a double-tailed fluoroalkyl amine chelating:metal chloride. 88% recovery of Pt-chloride into liquid carbon dioxide was achieved using the same chelating agent at a 3.5:1 ratio.

Jan 1, 1999

By Tung Vu, Michael Harrington

"The Regional Connector project is a complex subway light-rail project that runs through the heart of downtown Los Angeles, CA. The design-build contract was awarded in April 2014 to the Regional Connector Constructors (RCC), a joint venture between Skanska USA Civil West California District Inc. and Traylor Brothers Inc., and their designer team consisting of Hatch Mott McDonald (HMM) and subconsultants. The project broke ground on Sept. 30, 2014 and is expected to be completed in winter 2021-2022. The main components of the project consist of 6.4-m (21-ft) diameter twin-bored tunnels, three crosspassages, a 87-m (287-ft) long crossover SEM cavern, three new underground stations, and cut-and-cover tunnels along South Flower, Alameda and 1st Streets. The project map is shown in Fig. 1. The design and construction challenges associated with each of these main components are discussed in the following sections.Project designTunnels. The Regional Connector tunnels are located primarily within the Fernando formation consisting predominantly of extremely weak to very weak, massive, clayey siltstone. About 305 m (1,000 ft) of tunnels on the eastern end are in alluvium and mixed face of Fernando formation and alluvium. The tightest curve of the tunnel alignment is 178 m (583 ft) in radius. The tunnels were designed with a reinforced precast concrete tunnel lining (PCTL) to be used with an earth balance pressurized (EPB) tunnel boring machine. The PCTL ring is 5.5 m (18 ft-10 in.) inside diameter, 27 cm (10.5 ft) thick, 1.5 m (5 ft) long, and consists of five segments and a key. The segments were designed with 6,500 psi concrete, 80 ksi yield strength wire rebar, convex joint surfaces to enhance seismic performance, and a dosage of 1.7 lbs polypropylene microfibers per cubic yard of concrete for fire resistance. The rings are designed with a right ring and left ring pattern and a taper of 3.8 cm (1.5 ft) to allow for alignment curve negotiation. Figure 2 shows typical sections of the PCTL. The structural lining design was modeled using FLAC 3D. Four consecutive rings were modeled with 32 dowel connection. Loading considered in the lining design includes temporary ground load during excavation, long-term ground loads, seismic loads and train loads. The seismic loads on the PCTL were simulated with the racking deformation applied at vertical boundaries of the model. Due to variation of geologic condition along the tunnel alignment and different surcharge requirements, three different types of reinforcement (typical, heavy and extra heavy) were designed. The typical type PCTL was required in Fernando formation, the heavy type was required in alluvium or mixed-face condition, and the extra heavy type was required in alluvium and underneath the Japanese Village Plaza where a surcharge of 1,000 psf was required."

Sep 1, 2019

By M. Gunter, M. Buzon

"Talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic, and lacking in amphiboles. In southwest Montana, talc formed from hydrothermally altered dolomitic marbles, and is still actively mined. These talc deposits are typically in contact with quartzofeldspathic gneiss and marble. Accessory minerals vary between these rocks and the ore producing body; the identification and characterization of such minerals requires carefully selected analytical methods. Recent litigation and ensuing confusion over the petrology and asbestos content of these deposits challenges the talc mining industry in Montana, and elsewhere in the world. INTRODUCTION Commercial talc has been mined from the deposits in southwest Montana since the 1940s, and by 1956 the region had output 200,000 tons of talc ore (Chidester et al., 1964). Commercial talc refers to rocks containing more than 20% of the mineral talc (McCarthy et al., 2006); the ores from Montana typically contain upwards of 90% talc. This region remains the leading domestic source of talc in the U.S. partly due to the reserves in the area, and partly due to the diagnostic purity of the ore compared to that of other regions, some of which are no longer actively mined. The mineral talc, a sheet silicate, is expressed by the formula Mg3Si4O10(OH)2, and therefore can form in geologic environments that are rich in Mg, Si, O and water. The protolith for the talc deposits in southwest Montana is a dolomitic marble, but other common protoliths include ultramafic igneous, mafic igneous, and siliceous dolomites (McCarthy et al., 2006). Physical properties such as hardness of 1 on Mohs hardness scale, white streak and slippery feel are among some of the reasons why talc is so widely used as fillers in a number of industries. In decreasing order, ceramics, paper, paint, roofing, plastics, rubber, and cosmetics are the leading domestic industries that use talc despite the decreasing trend in U.S. talc use and production since 1994 (Virta, 2015). The purpose of this paper is to describe the mechanism of talc formation in southwest Montana by focusing on talc deposits and surrounding rocks in the Ruby, Greenhorn, and the Gravelly Ranges, and to relate the mechanism of formation to the composition of talc ores. The compositional data show mineral content of selected ores, and the major and trace element content of those minerals, specifically talc. Our electron microprobe (EPMA), powder x-ray diffraction (XRD) and x-ray fluorescence data for samples from five mines in these three ranges provide continued evidence of the purity of these ores despite claims made during recent litigation that these ores contain asbestos. The five mines that we discuss include the Beaverhead, Treasure, Regal, Willow Creek, and Yellowstone Mines (Figure 1.)"

Jan 1, 2016

By M. Deutsch

A common casualty of modern open pit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can really be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period. And grade control polygons may be ragged, narrow, and not minable with realistic equipment. In this paper all of these problems are addressed by encoding these three fundamental open pit mine optimization problems as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are non-linear and may guarantee the optimality that metaheuristics cannot. INTRODUCTION Open pit mines are large and complicated operations, which require significant initial and ongoing investment. A single mine may employ hundreds or thousands of people and creates substantial benefits for both the surrounding and global communities. Planning an operation of this magnitude requires a lot of effort and cannot be done optimally by hand. Mining engineers today rely on many techniques from operations research to guide decision making, and to maximize the value of the mine. Techniques including linear programming, metaheuristics, and network algorithms are all used to solve different problems throughout mine design and optimization. However, techniques based on Boolean satisfiability, including the optimization extension of maximum satisfiability, have not seen much use in mining despite being used in many other fields including electronics design, scheduling, and artificial intelligence. We claim that maximum satisfiability is a useful and meaningful way of expressing and solving optimization problems in mine planning. However, this technique does not come without challenges; the problem is NP-hard, and modern techniques for solving these problems can struggle with the number of variables and clauses that a typical mining problem requires. Also, some of the constraints that mining must contend with do not fit nicely into the satisfiability paradigm. Despite these challenges, we believe that maximum satisfiability provides a useful framework for considering operational constraints and expressing some problems that other techniques can't easily express. Maximum satisfiability can be solved exactly, yielding the true optimal answer which metaheuristics cannot guarantee. In this paper we show the applicability of maximum satisfiability to mining by specifying three fundamental problems in open pit mine optimization. We show how these fundamental problems can be formulated and how they can be extended within the framework of maximum satisfiability. For the remainder of the paper we first give a brief background on common elements between the three problems and an introduction to satisfiability. Then we tackle the three problems; the Ultimate Pit Problem, the Block Scheduling Problem, and the Grade Control Polygon Problem. In the Ultimate Pit Problem we specifically show how to extend the problem to support a minimum mining width – a coveted result for many mining engineers. We then discuss some of the complexities and shortcomings of this framework and possible research directions.

Jan 1, 2019

By J. Creamer

Pumping plays a major role across multiple process and facility applications in the mining world. Examples include: raw water supply, leach solutions, chemicals, dewatering, and mine drainage, and process water for metal recovery. Mining operations such as grinding, classifying, separating and concentrating minerals all have pumps at the heart of the operations Special purpose pumps such as dewatering, process water and slurry pumps are at the heart of many of these processes. Unfortunately the pumps themselves are often overlooked in terms of energy savings potential as they are often embedded into these sophisticated processes which are the ultimate operational focus.

Feb 23, 2014

By Emily Adelsohn, Robert Winn, Anthony Iannacchione

"Over 600 longwall panels have been mined in Pennsylvania in the last 50 years. Of those 600 panels, 25 panels undermined interstate highways. Despite this quantity of panels, much is still unknown regarding the detailed effects of undermining highways. The Gateway Mine, the Emerald Mine, and the Cumberland Mine undermined I-79 with 17 panels between 1982–1989 and 2003–2008, respectively; mine Eighty-Four undermined I-70 with 4 panels between 1987–2000.Through the examination of the panels that undermined I-70 and I-79, it is possible to determine which factors have most impacted the highway alignments. In some locations, the highway intersects with panels at angles ranging from 45 to 80 degrees, and at others, it runs between two panels, which simulates the effect of gateroads on the subsidence. The panels width to overburden ratio varies between 0.64 and 1.7, meaning that the interstates were influenced by both subcritical and supercritical subsidence basins. The face advance rates and overburden depths also vary between the panels.Unfortunately, specific information detailing highway impacts associated with unique characteristics of the subsidence basins are limited. However, using the profile function model and influence function model within the Surface Deformation Prediction System (SDPS), the effects of overburden, panel size, and orientation of the road to highway can be indirectly assessed by profile and influence models of subsidence basin formation.INTRODUCTIONCoal mining has been an integral part of Pennsylvania’s history. Room-and-pillar mines have been active since the late-1700s when coal was extracted from outcrops. By 1830, the city of Pittsburgh alone consumed more than 400 tons of bituminous coal each day for domestic and industrial use (PADEP, 2019). In the late 1960s, the face of mining in Pennsylvania changed with the development of full extraction longwall mines. Since that development, over 600 longwall panels have been mined in the Pittsburgh Coalbed in Pennsylvania alone (PADEP, 2019).As longwall mining and other forms of full extraction mining have increased in popularity, the amount of planned subsidence impacting the surface has also increased. The stresses and strains induced by longwall subsidence can cause damage to the surface as well any structures, water supplies, or water bodies that lie above the panel. Since the behavior of soils and structures vary, one way to study the surface effects of longwall mining is to analyze the impact on flat, rigid, pavement surfaces. Examining factors that vary the impact of subsidence with respect to highway alignment can demonstrate the favorable orientation of an alignment to avoid or mitigate damage and critical impact zones in a subsidence basin."

Jan 1, 2019

By H. Hoberg, M. Langen, B. Hamacher

Since the term "abandoned hazardous sites" was first coined in the 1978 environmental report of the Council of Environmental Specialists, a number of different types of technology has been developed in the Federal Republic of Germany for the remediation of contaminated soils /l/. At former sites of the mining industry, such as metallurgical and coking plants whose soil has been contaminated by organic and inorganic pollutants over decades of industrial activity, there is an exceeding necessity for soil remediation. Also, many former locations of metal processing works, battery factories or scrap yards have been contaminated in particular by heavy metals. Wet mechanical soil decontamination has proven successful over the past 10-15 years in the purification of these soils The process goal is the enrichment of the pollutants in certain plant products and the separation of a pollutant concentrate from the decontaminated soil. Table 1 lists the steps of the highly advanced wet mechanical soil decontamination process to achieve this process goal. Table 1 lists both the name of each process step and its goal in terms of a direct separation of the pollutant or the preparation of the soil for subsequent separation steps. For the separation of heavy metals, density sorting and separation techniques utilising flotation were specifically used. The use of chemical auxiliaries such as acids and lye is limited to special cases because these in themselves produce additional environmental impact and the economical effficiency of these techniques compared to conventional methods is lowered by supplementary process steps for water purification. The subject of this presentation is to consider how soil decontamination processes can be effectively improved through a description of the material properties of soils contaminated by heavy metals, and through carrying out basic investigations about the adsorption of heavy metals. Soils of different origins, especially those from former mining and metallurgical sites, were used for the experiments.

Jan 1, 1995

By Kostas Kaklis, Zach Agioutantis, Robin Flattery

Pillars are used as the primary support structures for underground mining to maintain stability by supporting the over laying strata. In the case of horizontal seams, the pillars are typically subjected to axial loading due to the weight of the overburden and/or abutment stresses, while in the case of inclined seams they are subjected to oblique loading due to both the vertical and horizontal in-situ stress.