Search Documents

By Bror Nyman

Wide settlers are a way to decrease the linear velocities of advancing liquid phases. It has, however, been found unnecessary to risk a proper settler performance by building shallow settlers in order to avoid a so-called interface turbulence due to a too big difference between the linear velocities of the organic and the aqueous phase. This conclusion has been reached from tests using a large transparent settler model, where the behaviour of a clean interface between two advancing liquids has been investigated. Also in a more realistic case, making an organic in aqueous or an aqueous in organic dispersion to move between the liquid phases, no obstacle has been found to use a somewhat more deep and correspondingly ore slowly t10wing aqueous phase. Based on above findings, support can be given to a new trend to build the settlers slightly deeper than what has been typical for the so-called low-profile design. In this way, it is much easier to avoid an excessive air introduction and other severe difficulties, like those caused by crud moving from one stage to another. It is further shown, how gravity can be used to slow down and distribute a dispersion being fed into a settler of a VSF unit. Entrainment levels have been found to be reduced by a careful design of primary dispersion distributors and picket fences of the settler. Finally, it is demonstrated, how outlets from the side of the settler can be used to simplity interstage pumping and to decrease the rotation speed of any pumping device.

Jan 1, 1996

By Eugene F. Eisemann

This paper is concerned principally with the competition between fuels for industrial use in the United States. Total energy consumption in the U. S. is allocated between industrial and other uses The industrial volume is divided into two classifications (1) where-there is competition between fuels and (2) where there is no competition. The pattern of fuel consumption by electric utilities was studied because there, is competition between fuels and because it is the fastest-growing industrial market. Electric utilities fuel consumption is discussed by geographic area. The growth of each fuel in several areas is investigated. The analysis of these areas, includes the study of the relationship between prices where fuels are in, competition:- (1) on the East Coast where price competition occurs between oil and coal, and (2) in the southeastern states where competition exists between coal and gas..

Jan 1, 1961

By A. Noble

For the past 30 years, process flowsheet design has been accomplished largely through modeling and simulation. This approach provides circuit designers the freedom to test various separation approaches while minimizing physical and human resource requirements. The Limn® software provides a unique approach to process simulation, through a Microsoft Excel interface. While the software comes with standard process models for numerous unit operations, the Excel calculation environment and the accompanying VBA platform provide a convenient interface for custom model integration, even for non-experienced programmers. This feature is especially useful for university students in introductory process modeling and simulation-assisted flowsheet design courses as well as experienced practitioners with proprietary process models. This paper shows how the Limn® software may be used to solve basic process engineering problems as well as more comprehensive circuit design challenges. Industrial examples as well as opportunities for training and education are presented.

Feb 23, 2014

By J. Kretschmann, R. Amiri

"The Sangan iron ore mines (SIOM) in Iran are located in a remote area near the Afghanistan border. The SIOM deposit contains a geological resource of 1.1 Gt (1.2 billion st) of mostly magnetite with an iron (Fe) grade ranging from 27 to 61 percent. The Iranian government plans a stepwise development of SIOM in cooperation with private companies to satisfy the growing demand of the Iranian steel industry. Sustainable development is an influential ethical concept in mining all around the world. However, a successful realization of a sustainable development plan is not possible without a foundation on the core values and regarding the specific circumstances of the individual mining country. This paper introduces SIOM and describes sustainable development activities undertaken during its development. From the early stages, these activities have been realized to secure the acceptance of the stakeholders in the region. To evaluate their effects, indicators were filtered to the ones with the highest priority for the stakeholders. Moreover, Islamic values and Iranian regulations and their influences on SIOM were analyzed.Mining industry in Iran The Islamic Republic of Iran holds 68 types of minerals, including salt, sand and gravel, gypsum, chrome, lead, zinc, copper, coal, gold, iron, etc., with 33.5 Gt (37 billion st) of proven reserves and more than 51.7 Gt (57 billion st) of potential resources. Iran is ranked among the 15 major mineral rich countries (1). In accordance with the statistics published by Statistical Center of Iran (SCI), there were 5,316 active mines and 84,922 employees in the whole country in 2012-2013 (2) and, according to the statistics published by Central Bank of Iran (CBI) in 2011, the share of this sector in the gross domestic product (GDP) of the country was 1.2 percent (3)."

Jun 1, 2016

By Brianna Eiter, Max Barham, Tim Bauerle

Fatigue-related risk is a persistent safety concern for the mining industry. However, fatigue and sleepiness are often treated interchangeably, which can lead to confusion and potentially less effective reduction of safety risk. To provide clarity, we present an overview of similarities and differences between work-related fatigue risk and sleepiness including definitions, theories, measurements, and mitigation strategies. As a supplement, a summative visual model which highlights these similarities and differences is presented. Expanding industry knowledge in this area will assist safety professionals in crafting more targeted risk management practices appropriate for work-related fatigue risk, sleepiness, or both.

Dec 19, 2023

By J. R. Schafler, J. L. Brinkman

"The US coal mining industry has suffered a recent decline in profits caused by a combination of decline in commodity demand and more restrictive government regulation, forcing coal mining companies to cease production in numerous mines. A 40% decrease in the total number of coal mines occurred from 1994 to 2000. The number of mines remained relatively constant until 2008 when a change of government sparked a series of new environmental regulations which have contributed to another 15% decrease from 2008 to 2016. In contrast, production has only decreased by 3%, increasing from 1994 to 2008, and then decreasing since 2008. However, this value is skewed by large increases in sub-bituminous coal production and decreases in other coal ranks. Several aspects assist in executive decisions on mine longevity and economic worth. Studies of open source mine data collected by mandated government surveys coupled with commodity history can be used to find relationships between mine closures and these elements, which include statistics on production tonnage, seam height, coal rank, etc. This paper looks at coal mining trends since 1994 by comparing mine, market, and regulation factors that may influence mine closure. INTRODUCTION The US coal mining industry is currently experiencing a decline in both demand and commodity price while facing implementation of more stringent air and water pollution regulations. Company profits have decreased significantly, forcing several major companies to declare bankruptcy. The industry was required to adapt to survive. Many of these companies have adjusted by abandoning mines; the last two decades have seen a drastic decrease in the number of mines. To discover the primary causes of this downturn, three major aspects must be studied: properties of abandoned mines, commodity history, and regulatory impact. TRENDS SINCE 1994 Each year, US coal mines are required to submit data on a wide variety of categories to the Mine Safety and Health Administration (MSHA) and the US Energy Information Administration (EIA). This data includes administrative records, production values, and information regarding the attributes of the mined material and the mine itself. Each year since 1996, EIA has released a report summarizing the data from two years prior. Additionally, MSHA maintains a database containing a collection of all the most current data. These resources are the primary sources for the following figures."

Jan 1, 2017

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using an untreated rock dust and a rock dust treated with an anti-caking additive. Using PDM 3600s and 3700s, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine (BEM) using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device. INTRODUCTION Two factors have combined to renew concern regarding respirable dust measurements and compliance. This renewed recognition is due to two regulations that have modified operators’ rock dust schedules. First, the 80% incombustible requirement in intake entries has increased both on-section and outby-the-section rock dusting. Secondly, the recent respirable dust regulation change that has increased the number of respirable dust samples taken per sampling cycle. Previously, when only 5 samples were needed bi-monthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule. The significant number of samples now required under new regulations combined with the need to maintain 80% total incombustible content in active mining areas require the schedules for respirable dust sampling and rock dusting to intermix. This raises concerns about the amount of rock dust that potentially is included in the sampler weight gain. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 (effective August 1, 2016) increasing concern that rock dust contamination may be an issue. Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application or to schedule rock dusting during a maintenance shift when the number of miners present is lower. NIOSH’s research examining the quality of rock dust has led to the development of hydrophobic rock dusts."

Jan 1, 2017

By C. Zhou, J. Srednicki

Electronic systems have been increasingly used in underground mines to improve mine safety. These electronic systems emit electromagnetic (EM) energy which can adversely impact the performance of other electronic systems nearby and thus should be characterized. Researchers at the National Institute for Occupational Safety and Health (NIOSH) characterized the magnetic fields emitted from devices that can potentially interfere with the performance of proximity detection systems (PDSs) and compared the emission levels of these devices to the susceptibility of PDSs. In this paper, we present our measurement results pertaining to this effort. Particularly, magnetic fields emitted from the different orientations of a powered air purifying respirator (PAPR) and two lite trackers are evaluated based on the RE101 protocol specified in the MIL-STD-461G standard. The results show that both devices emit strong magnetic fields which strongly depend on the orientation of the devices. At some frequencies, the maximum emission levels from the two devices exceed both the emission limit given in MIL-STD-461G and the maximum magnetic fields that a PDS can withstand without a failure. The results and findings in this paper can help the mining industry better understand electromagnetic interference (EMI) underground and provide critical scientific data that support mining-specific recommendations to address EMI-related challenges.

Feb 1, 2023

By Ashish Ranjan Kumar, Barbara Arnold, Luis Sanchez Gonzalez

The health and safety of miners is critical in the industry. Prolonged exposure to dust-laden air results in irreversible ailments like pneumoconiosis that have a severe impact on their lives. Operations use various personal protective devices (PPEs) to alleviate their exposure to respirable dust. Powered Air Purifying Respirator (PAPR) is one such device that uses high- efficiency filters and positive pressure masks to shield miners from airborne contaminants. Used in the medical and other industries, these respirators efficiently protected healthcare workers during the COVID-19 pandemic. Recently, the mining industry has shown a growing interest in adopting this PPE to ensure safe working conditions for the miners. We present an introduction to the PAPRs and discuss their dust capture efficacy in this manuscript.

Feb 1, 2025

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By Ravindra M. Chhatre

Uranium associated with phosphate deposits has been the subject of numerous investigations (1-8). In the land-pebble phosphate deposits of central Florida, uranium is found in the phosphate matrix (ore) and in the leached zone between the over-burden and matrix (1). Between 0.01 to 0.02 percent uranium is found in the leached zone, which consists of apatite and aluminum phosphate minerals (crandallite, wavellite, millisite) (Z). The primary phosphate mineral in the matrix is apatite, and the 0.005 to 0.01 percent uranium typically found in the matrix is associated with this mineral (1). It is generally believed that uranium substitutes for calcium in the apatite structure (3-5). Clay and quartz phases associated with phosphate deposits contain little uranium (1, 6), and no descrete uranium minerals have been detected in these deposits (4). A typical phosphate matrix consists of quartz, slimes (-150 mesh material) and recoverable phosphate. When the matrix is beneficiated, partition of uranium and radium takes place (9, 10). Although considerable data exists on how uranium is distributed in the phosphate deposits, no systematic study has recently been reported on the distribution of uranium during phosphate rock beneficiation. The purpose of this study was to determine how uranium is distributed in the various strata which comprise the overall land-pebble phosphate deposits, as well as how the uranium is redistributed during beneficiation of phosphate matrix. To obtain this information studies were carried out on matrix samples obtained from three different mines in central Florida. Using pilot-plant scale beneficiation, an analysis was performed on how uranium in the matrix is distributed among the pebble fractions, flotation concentrates, flotation tails, and slimes. The uranium level profile for an active mining area was also obtained. Also, since thousands of acres of slime ponds may someday become a source of both phosphate and uranium, a depth versus uranium content profile was determined for an inactive slime pond.

Jan 1, 1978

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dozer operators are frequently exposed to whole-body vibration (WBV) during the execution of their work. Occupational exposure to WBV in Indian surface coal mines was evaluated by measuring vibration intensity and duration of exposure. A triaxial accelerometer was placed on the operator seat surface for taking the readings. Based on frequency-weighted root mean square acceleration equivalent to 8-hr shift duration, i.e., (A(8)) all dozer operators have exceeded an Exposure Action Value (EAV) of 0.5 m/s2 , and 90% of dozers did not exceed Exposure Limit Value (ELV) of 1.15 m/s2 . Based on Vibration Dose Value (VDV (8)), all dozer operators have exceeded Exposure Limit Value (EAV) of 9.1 m/s1.75, but no dozer operators have exceeded Exposure Limit Value (ELV) of 21 m/s1.75. Further, an epidemiological study was performed for identifying the extent of musculoskeletal disorders (MSDs) among dozer operators. For the detailed study, 42 dozer operators and 22 controls were selected from 2 surface coal mines. The control group was not exposed to WBV. It was seen from the cross-sectional study that pain in the lower back was predominantly higher (83.33%) in the exposed group when compared with the control group (31.81%). Likewise, pain in the neck (47.61%), shoulder (42.85%), knees (42.85%), and ankle (11.90%) was higher in the exposed group than that of the control group (22.71%, 0%, 45.45%, and 4.54%). A significant observation among the exposed group was that there was degradation in the quality of life. The outcome of the study would assist in monitoring and mitigation of machinery-induced vibration diseases (MIVD) in India and generally applicable to most of the mechanized mines as well. However, comprehensive studies are still needed to enunciate the magnitude extent.

By James S. Browning

In 1975 bituminous coal and lignite production in the United States reached an all-time high of 637 million tons, an increase of 6 percent over production in 1974. The output, valued at $11.9 billion f.o.b. mines, was produced at 5,100 mines in 24 states (6). Coal mining is the largest mining industry in Alabama. Production from Alabama's mines in 1975 was over 21 million tons, and present projections forecast a steady increase in production, with tonnages almost doubling by 1985 (5). Of the total quantity of coal produced, about 16 million tons were consumed in electric power generation and the remainder was used for metallurgical coke production, extraction of chemicals and petroleum based products, and power for industry. The fact that 75 percent of Alabama's power is generated by burning coal attests to the importance of this fossil fuel to the State. Approximately 14 million tons of coal were produced by strip-mining methods in Alabama during 1975 and about 7 million tons were produced by underground mining during the same period. Surface mining is expected to continue at about 14 million tons per year, but by 1980 underground coal mining is expected to increase to about 25 million tons (3). About 7 million tons of surface-mined coal in Alabama is subjected to some means of washing or cleaning. The methods used are screening accompanied by heavy media separation, jigging, tabling and flotation. Some of the simpler approaches employ screening and jigging, or tabling. Except where flotation is used, the screen undersize fraction (finer than 0.25 inch) is rejected, with the result that 10 to 15 percent of the coal is lost. Thus, in the State of Alabama an aggregate of about 1 million tons of coal is wasted annually in the fines which are impounded from treatment of surface-mined coal. The use of the Humphreys spiral to concentrate fine coal was practiced as early as 1947. At that time the Hudson Coal Company (1) used Humphreys spirals to concentrate anthracite fines. In 1950, the use of spirals to treat fine-size

Jan 1, 1977

By J. A. Botín

Investment decision for large mining projects imply an enormous financial risk and therefore, require a more complex risk evaluation methodology taking into account all sources of uncertainty from each process in the project value chain. Generally, the main sources of risk are those related to uncertainty on grade and other techical variables of the orebody. In this study, conditional simulation is applied to develop a risk management model to quantify and to manage financial risk associated to uncertainty on the grade of the orebody. The model was validated in case study on a real porphyry copper orebody in Chile.

Feb 23, 2014

By E. B. Fitch, D. A. Dahlstrom

Liquid-solids separation is common to practically all mineral and coal processing as the bulk of beneficiation plants employ water as the major processing vehicle. The growing usage of hydrometallurgy has increased the importance of liquid-solid separation as acidic and basic solutions result in greater amounts of colloidal solids, with their consequent greater difficulty of separation, the economic need for chemical recovery to minimize this operating cost, and the usual necessity of employing more costly construction materials. The three processing steps covered in this section have significant capital costs. Drying, particularly, has an important operating cost because of the obvious need for energy to evaporate the water or solvent. Several common factors influence all three liquid-solid separation steps. Particle Size and Size Distribution. In general, finer particles have slower settling and filtration rates. The specific surface area is increased, which means a lower solids concentration in the thickener underflow and discharged filter cake as well as a grater moisture content to be evaporated in the drying step. Therefore, overgrinding or excessive attrition should be avoided. Consideration should be given to optimum particle size consistent with entire plant operation performance and recovery. Solids Concentration. Increased feed solids concentration will generally minimize required equipment size and costs in all three liquid-solid separation steps. Most thickeners are designed on the basis of unit area required, expressed as square feet per short ton of dry solids per day (square meters per metric ton per day) which will usually decrease with increased feed solids concentration. Filtration rates also increase as the required flow through the capillaries of the filter cake decreases. Dryer capacity increases and less energy per ton of final product is required to evaporate the associated moisture. Particle Shape and Surface Characteristics. Generally, optimum shape is a spherical particle of zero porosity. As either of these factors degrade away from the desired state, difficulty increases. This is particularly true in drying, where porosity can decrease drying rate significantly if the moisture must first reach the particle surface by diffusion

Jan 1, 1985

By F. L. Bazzanella

Cyprus Pima has two concentrators, one with a conventional crushing-grinding circuit and the other using semi-autogenous grinding followed by ball mills.

Jan 1, 1978

By Mustafa Akser

Dwindling economic deposits of rutile (TiO2) prompted research on recovering it from secondary sources. One such resource is in Southwestern Turkey feldspar mining rejects that contain 5%-6% TiO2 mostly rutile. Previous studies could only upgrade the TiO2 to 36% TiO2 grade, claiming that the leftover flotation reagents on the surfaces of rutile and host minerals detrimentally affected upgrading of the rutile. As a potential remedy to this concern, a laboratory sample (from an operating feldspar mine in Milas, Turkey) was first caustic scrubbed, then air calcined at 400°C to evaporate the oily reagents. Subsequent physical separation of rutile included wet screening, gravity, magnetic, and electrostatic separation technologies. Such processes indeed improved the grade of the rutile concentrate up to 83 % TiO2 Low recovery of the TiO2 (<20%), was attributed to lack of full liberation of rutile, even at 125x44 micron range; interference with impurity minerals such as sphene and zircon; and simply the process inefficiency in upgrading the fine grains through conventional separation technologies for heavy minerals.

Jan 1, 1999

The role of ZnSO4 in activation of sphalerite (ZnS) and deactivation of lead-activated sphalerite has been investigated. Adsorption of metallic ions at the solid-solution interface, electrokinetic results for sphalerite under different chemical conditions, and thermodynamic calculations were used to elucidate the mechanisms involved. It is shown that flotation response of sphalerite in absence of activators is rather weak and that adsorption of ethyl xanthate on the mineral mainly electrostatic in nature. Zinc sulfate is found to activate the mineral but only in a narrow acidic pH range. This is attributed to the increase of zeta potential as well as the possible increase in amount of negatively charged bulk precipitated zinc xanthate. Lead ions activate sphalerite in a wide pH range and the lead activated mineral assumes a flotation behavior similar to that of galena (PbS). However, addition of ZnSO4 depresses the lead-activated sphalerite by replacing lead ions at the mineral/solution interface.

Jan 1, 1999

By Apostolos Vrakas, Georgios Anagnostou

"INTRODUCTION The small strain assumption routinely made in tunnel analyses remains sufficient from an engineering point of view as long as convergences do not exceed 10%. More specifically, small strain theory assumes that deformations are so small (in relation to the size of the underground opening) that any geometric change in the continuum can be disregarded (Fig. 1a). In fact, however, the geometry is updated during loading (or unloading) according to large strain theory and thus equilibrium and stiffness are evaluated on the deformed configuration of the continuum (Fig. 1b).In problems involving large deformations, where the undeformed and the deformed tunnel geometry differ significantly, small strain theory leads to erroneous and sometimes even nonsensical results (i.e. it can predict wall displacements even greater than the excavated radius under conditions of very low stiffness and strength, high in situ stress and low support pressure). This can easily be verified from the widely applied relationships for the ground response curve. For example, in the ideal case of linearly elastic behaviour, the convergence of an unsupported opening equals (1+?) s0 / E (where E, ? and s0 denote the Young’s modulus, Poisson’s ratio and initial isotropic stress, respectively) and is greater than 100% for E < (1+?) s0. Although convergences are less than 10% in the great majority of tunnelling projects, very large deformations may take place when tunnelling through weak rocks under a high overburden (Fig. 2). This paper will first present a very simple and practicable way to account for large strains, based entirely on the results of routine small strain analyses, and will subsequently show the importance of addressing large strains in tunnel analysis and design with reference to three typical case studies of tunnelling in squeezing ground."

Jan 1, 2016

By Güldane Atesoglu, İsmail Atilgan

The changes in the elemental contents and the structural properties of chalcopyrite concentrate when roasted were studied, and the main reactions contributing to the leaching process revisited. Firstly, TG/DTA measurements were performed to identify the roasting temperatures that influenced the type of species reacting with sulphuric acid leaching liquor. The temperatures of main reactions, whose output may affect the subsequent leaching process, were analysed for the concentrate at hand, and concluded to be generally lower than those reported in literature. Secondly, the obtained results were confirmed by images and XRD measurements on the roasted concentrate at temperatures in between 350 and 600 °C with increments of 50 °C. Finally, the leaching behaviour of the roasted specimens in a stirred sulphuric acid solution examined and the Cu/ Fe selectivity investigated that the maximum Cu/Fe ratio in the pregnant solution would nearly be achieved for the roasting temperatures lower than 500 °C, since the oxidation temperature of iron sulphate is found lower than that of copper sulphate.

Aug 11, 2022