Search Documents

By P. T. Bissert, L. Yan, M. D. Klein

"Since 2008, the U.S. Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines (MSHA, 2008). MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. In its 2006 report, the West Virginia Mine Safety Technology Task Force (2006) recommended an apparent temperature limit of 35 °C (95 °F) for RAs. In Title 30 Code of Federal Regulations Part 7.504, or 30 CFR 7.504, MSHA specifies a maximum apparent temperature of 35 °C (95 °F) inside an occupied RA (MSHA, 2016). The apparent temperature is calculated using both air temperature and relative humidity (Steadman, 1979).Calculations can be used to deter-mine if the air within an occupied RA will reach the apparent temperature limit. In these calculations, the mine temperature could be assumed to re-main constant. With this assumption, the effects of the mine strata thermal mass and thermal conductivity on the heat buildup in an RA are ignored. Re-search conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) shows that the mine air and strata temperatures surrounding an RA increase when subjected to the heat of an occupied RA (Yantek, 2014). Thus, calculations performed with the assumption that the mine temperature is constant would underpredict the resulting dry-bulb temperature and apparent temperature for a given RA occupancy. The mine air temperature has been used as the basis for RA temperature calculations. However, there has been no research to confirm that the mine air temperature is the appropriate basis."

Apr 1, 2017

By M. P. Roy, P. K. Singh, A. K. Mishra, Ashish K. Vishwakarma, Vivek K. Himanshu

Ground vibration is one of the major hazards produced by rock-blasting operation. The accurate prediction of vibration is necessary for designing controlled blasting parameters. The existing vibration predictors consider maximum explosive charge weight per delay and distance as the parameters responsible for ground vibration. These predictors are based on the assumption that the geometrical parameters of the blast will be constant for a site. However, the mining sites with bigger production targets have varying geometrical parameters to suit the excavator utility. Accordingly, the other blast design parameters will also have an impact on ground vibration intensity. A principal component analysis is a dimension reduction technique. This technique along with multivariate logarithmic regression has been used in this paper to predict the ground vibration. The technique has classified the blast design parameters into four principal components. The regression with the scores from these principal components has been carried out. The evaluation of the model performance of predictors along with the existing empirical predictors has been carried out using R2 and RMSE values. The evaluation suggests that the predictor with logarithmic regression followed by principal component analysis gives better performance with respect to the existing empirical predictors.

Jul 30, 2022

By A. Haghighat

The Missouri University of Science and Technology?s (Missouri S&T) Experimental Mine is a teaching and research facility which has been excavated in limestone by mining engineering students over almost 100 years. The mine is currently being extended to a second level. Available fans for ventilation are two surface fans of 24 kW and two underground booster fans of 12 kW. The design of a ventilation network in conjunction with multi surface fans and booster fans entails a complex procedure. Ventsim Visual software modeling has been used for network analysis to determine the optimum surface and booster fans locations, blade settings, and speeds. Both natural and mechanical induced ventilation pressures have been taken into account. Three working faces on each level have been designated as target points that minimum air quantities are required. The model has been calibrated against a pressure and quantity survey. Design of ductwork, door/stopping positions and different fans characteristics have been examined. The optimum flow rate at identified working faces, efficiency and minimum energy losses and annual network power cost determine the best scenario. The optimum design has been determined for the ventilation network for the next 100 years. The optimum flow rate across working faces is the key criterion selected.

Feb 23, 2014

By F. S. Knoll

Electrostatic separation is one of the most misunderstood physical processes used to beneficiate minerals. Nonetheless, millions of tons of titanium ores, iron ores and other minerals are processed every year economically, efficiently and safely. Over the past ten years major advances in electrostatic separation and its application have occurred. New processes include dewatering clay slurries, separating halite and sylvite, and shape separation of vermiculite and gangue minerals. Electrostatic separation techniques are based on one of two methods, electrophoresis or dieleccrophoresis -- processes involving charged and uncharged particles respectively. In some cases, the combination of these two techniques has proven quite useful. The purpose of this paper is to provide a basic understanding of the physical processes collectively called "electro- static separation" in order to enhance one's ability to define and consider new possibilities in mineral processing and other fields.

Jan 1, 1984

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024

By A. J. Basu

Geotechnical design plays a key role in mine design. I A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches I) judgmental, based on observational and experiential facts, 2) empirical, based on empirical design formulae, and 3) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools was addressed earlier (Basu and Kuruppu, 1995). The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing structures applicable to mining geomechnics. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis application in excavation design.

Jan 1, 1996

By Harold J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The scooptram that is used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine the effect of exhaust pipe location and time spent out of the drift, as well as to determine if a relationship existed between CO2 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that has the capability of predicting changes in source strength as well as source location. It was also determined that four relevant factors include effective heading height, apparent longitudinal diffusion coefficient, transverse concentration gradient at the face, and average dispersion width of the exhaust jet. As these factors change with heading geometry and ventilation configuration, they were determined experimentally, Carbon dioxide was used as a tracer to calibrate the model; since, knowing the fuel flow rate, it is possible to calculate CO2 production. The above four factors in the computer model were calculated using a regression analysis, comparing predicted local concentrations to measured local concentrations. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field. A parametric analysis shows that the exhaust pipe location can have a significant impact on operator exposure to exhaust gases. It was also shown that NO concentration varies directly with C02 levels. Predictions using the dynamic model are contrasted with constant source strength (pollutant flow rate) results. An analysis of these predictions for computing time-weighted average NO shows the dynamic model predictions of operator exposure to this pollutant to be less than one-half of the value predicted using a constant source model.

Jan 1, 1981

By F. W. Jessen

The production of salt through brining operations and the recovery of potash salts by means of solution with water constitute, in large measure, processes which have been used for many years. And although the salt industry has utilized dissolution techniques for years and years it has been only recently that a better understanding of the mechanism of solution has emerged. Greater adaptability of solution mining processes for recovery of valuable salts from ore bodies found at greater and greater depth has resulted in increased adoption of such methods. Because of the high costs of mining in beds of limited thickness, modifications probable when extracting mixed halites, and restrictions (mostly self-imposed) regarding the extent of cavern development to minimize or eliminate subsidence more information is needed on the solution mechanism. It is the purpose of this paper to present the fundamental aspects of the problem of total solution of salts and to point out the developments of certain solution mining techniques.

Jan 1, 1971

By S. A. McGhee

Introduction ASARCO's Ray Operations include an open-pit copper mine in the Mineral Creek Mining District of Pinel County. The district is located in east central Arizona, 132 km (82 miles) southeast of Phoenix, AZ, and 126 km (78 miles) north of Tucson, AZ. The mine lies 8 km (5 miles) north of the Gila River in Mineral Creek Valley, between the Tortilla Mountains to the west and the Dripping Springs Range to the east. The rich copper deposits of the Mineral Creek mining district were first noted by a US Army Officer in 1847. The Ray Copper Company was the first major operation in the area. The company was named after the Ray mining claim, which was one of the earliest recorded claims. After decades of sporadic and unsuccessful mining ventures, the Ray Consolidated Mining Company was formed in 1910. The company introduced one of the first successful block caving operations in the world. In 1933, the Kennecott Copper Corporation acquired the Ray Consolidated Mining Company and continued operation of the mine under the same name until 1943, when the property was renamed the Ray Mines Division of Kennecott. Underground mining continued until 1955, when the mine was converted to an open pit operation. In November 1986, ASARCO Inc. purchased the Ray Mines Division and related facilities from Kennecott. The purchase also included the Hayden concentrator and the Ray Smelter, located approximately 32 km (20 miles) from the Ray Mine. This paper summarizes the 54,400 tpd (60,000 stpd) in-pit crusher and overland-conveying system and the 24,200 tpd (30.000 stpd) copper SAG concentrator and tailings disposal system constructed at ASARCO's Ray Complex - Ray Operations. General description of facilities The Ray concentrator includes a sulfide SAG concentrator, a "relocatable" in-pit primary-crushing plant and overland-conveyor system, a concentrator tailings-disposal system and plant ancillary facilities, The major elements of the project include: • A relocatable Fuller-Traylor in-pit 1524-mm (60-in) x 2261-mm (89-in) primary gyratory crusher at the 442 m (1450 ft) mine elevation. The crushing plant has a nominal capacity of 54,400 tpd (60,000 stpd) of sulfide ore. • A 1524-mm (60-in) wide x 1253-m (4110-ft) long overland belt conveyor, which runs from the in-pit crushing facility to a transfer station serving both the Ray Concentrator and the existing Hayden concentrator railroad load-out facility. • A 1524-mm (60-in) wide x 152-m (500-ft) long stackerbelt conveyor, which delivers a nominal 27,200 tpd (30,000 stpd) of ore from the transfer station to a 23,600 t (26,000 st) live-capacity coarse-ore stockpile serving the Ray Concentrator. • A nominal 27,200-tpd (30,000-stpd) concentrator, including semiautogenous grinding, flotation, copper concentrate filtration and associated plant ancillary facilities. • A tailings disposal system. Flotation tailings are pumped from the Ray Concentrator to a 122-m (400-ft) diam. thickener, located 4.8 km (3 miles) southeast of the Ray Concentrator site. The thickener overflow is pumped to two 76.2-m (250-ft.) diam. concrete process-water reservoirs. The thickener underflow, at 45% solids, is pumped to a new tailings disposal site located at Elder Gulch. • An HDPE-lined temporary-containment area to collect material from Ray Concentrator plant upsets and local storm-water run-off from a 100-year, 24-hour rain event. •A reclaim-water system from the Elder Gulch tailing pond area to the Ray Concentrator. • A 610-mm (24-in.) diam. x 31.9-km (19.2 mile) long fresh-water pipeline from the Hayden fresh-water-well field system to the Ray Concentrator. The overall process design criteria for the new Ray Concentrator is based on a nominal throughput of 27,200 tpd (30,000 stpd) of ore at 90% plant availability. However, based on the maximum performance capacity of the installed grinding equipment, it may be possible to achieve a sustained operating level in excess of 36,300 tpd (40,000 stpd) when processing soft ores. The balance of this paper will cover the major process systems including:

Jan 1, 1995

By MOHAMMAD R. H. GORAKHKI, Christopher A. Bareither, MANUEL APARICIO, Joseph Scalia IV

The focus of this study was on the evaluation of hydrologic and environmental behavior observed in GeoWaste and waste rock test piles. GeoWaste is a mixture of fast-filtered tailings and waste rock prepared as a tailings-dominated mixture. The two test piles included potentially acid-generating (PAG) waste rock and were operated for 26 months to evaluate whether GeoWaste can suppresses sulfide oxidation and production of metal-rich acid mine drainage relative to PAG waste rock. The test piles were constructed in the shape of truncated 5-m-tall pyramids with 25-m base sides and flat 5-m × 5-m top surfaces. Water content, temperature, electrical conductivity, and oxygen concentration were monitored in four layers and at five locations within each layer in both test piles. In addition, 5-m × 5-m lysimeters were installed at the base of each pile to collect leachate. Approximately 2660 mm of water was added to the surfaces of the test piles via precipitation and irrigation (irrigation ≈ 1050 mm applied at an approximately constant rate for 70 days). The measured saturation, oxygen concentration, electrical conductivity, and temperature in the GeoWaste and waste rock piles suggest more sulfide oxidation occurred in the waste rock pile compared to the GeoWaste pile. Observations from the pile experiments suggest that co-managing mine waste in the form of GeoWaste reduced acid generation compared to waste rock alone due to the lower permeability and unsaturated state of the GeoWaste pile that reduced downward migration of moisture and inhibited drainage.

Mar 31, 2021

By John C. Draper

Little precise information is available on the effect of mining on the surface topography. It is often assumed that after mining the surface will simply sink. This is not an infallible conclusion as is well illustrated in two of the three examples herein. This paper describes the results of an attempt to precisely measure the surface movement in the area around coal pillars left in place for three oil wells in a completely mined and caved area at the Harwick Mine of the Duquesne Light Company. The dates when the various measurements were made are shown on the data sheets and indicate the rate of surface movement. These oil wells are identified as wells Nos. 2, 3, and 6. This mine property is located on the north side of the Allegheny River at Cheswick, Pennsylvania, and extends in a northerly and westerly direction about five miles. The three well pillars are situated on the westerly side of the Bessemer and Lake Erie Railroad some 2,000 feet from Rural Ridge, Pennsylvania (Fig, 1).

Jan 1, 1964

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020

By D. D. Xu

A novel system for the depression of pyrite and the ash-forming minerals has been developed. A metal ion, including but not restricted to Fe+2, is added to form a hydroxide coating on the pyrite or ash-forming mineral. A polymeric depressant is then added to attach to this re-surfaced mineral. Nearly 200 flotation tests with a 11 different coals indicate the effectiveness of this system. Many of the important process variables such as the coal source, frother-collector system, grind size and procedure, pH, metal ion, and depressant type and concentration have been studied.

Jan 1, 1994

By Lorraine Brandt Yde

This paper describes development of a cost report that is descriptive, logically oriented, and concise. Since the costs involved relate to mining, this reporting technique could help bridge any possible communications gap between "mining men" and computer personnel, at the same time giving the computer-oriented mining individual information to assist him in his job performance. As computers become entrenched in the mining world, meaningful report assimilation becomes a major task. No one should be more capable of defining required results than the man requesting a report. If he is able to clearly state his needs and has researched his problem, it will be reflected in the computer output. During 1970, The Anaconda Company's Berkeley Pit Operation, at Butte, Montana, received many different computer-generated equipment cost reports. Up to thirty-six different components for each type (class) of pit equipment contributed cost data to the Berkeley Pit cost system files for both operating and repairs during current month, year-to-date and accumulation-to-date time periods. This reporting approach was taken to facilitate analyzing this voluminous data. SUMMARY A Major Component Cost Analysis (Exhibits 6-A thru 6-C) developed by arranging the top ten operating and repair percentages (component cost divided by total cost) in descending order, and then accumulating these percentages to a possible one-hundred percent. While tabulating the operating and repair cost percentages by equipment unit number in the current month, year-to-date and accumulation-to-date time periods, a frequency chart is constructed for each equipment

Jan 1, 1971

By D. Van Orden, Y. Kamiya, R. Lee, E. Ilgren

Crocidolite is a well-known causative agent for mesothelioma. However, studies have shown that the pathogenicity of the fiber from different mines varies considerably and it has been postulated the parameter that appears most likely to account for this variation is fiber width although this has never been formally confirmed. To date, crocidolite appears to be the only asbestos mineral for which an epidemiological study comparing the risk of mesothelioma in a population exposed to ‘thin’ fibers with another exposed to ‘thick’ fibers of the same species may be carried out. Finnish anthophyllite, South African amosite, and African Transvaal crocidolite can also be classified as thick fibers, and there is a paucity of mesotheliomas in populations exposed to them compared to those exposed to thin Cape crocidolite. No thin occurrences of these minerals are known. Our previous study looked at crocidolite from several sources. The present study considers the amphibole anthophyllite found in many places in the world. This mineral, regardless of source, does not show the same variation in fiber width found with crocidolite from different areas. All anthophyllite fibers that have been mined may be classified as thick and populations exposed show very low levels of mesothelioma. We suggest the most likely explanation is related to the fiber width distribution and a concomitant reduction in the ‘Stanton fiber size’ fraction.

Jan 1, 2012

By Scott Rosenthal, David Gilkey, Michael McGivern, Lorri Birkenbuel, Daniel Autenrieth, Ty Murphy, Hadi Aldossari

A safety climate case study was carried out at a surface metal mine where investigators administered the Liberty Mutual Short Scale Safety Climate Survey to 365–368 miners to measure safety climate in consecutive years. Following the baseline safety climate survey in 2019, Foundations for Safety Leadership (FSL) training was conducted with 81 middle to upper management employees at the mine site. Investigators found statistically significant differences in the pre vs. posttraining FSL assessment scores of the middle to upper management employees who attended the training. The follow-up safety climate evaluation was compared to baseline scores and revealed no significant improvement. The overall baseline company safety climate score of 76.38 increased minimally to 76.50 (p-value = 0.616). Investigators also evaluated differences in safety climate between the company’s three major divisions (operations, maintenance, and administration). Both years administration had the highest mean score and operations had the lowest mean score. The authors attributed the statistically significant differences found among the three major divisions to various dissimilarities in their work environments.

Aug 13, 2021

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

During harsh weather conditions, the presence of fog, dust in the environment degrades the image’s quality, which affects the visibility of drivers of heavy earth-moving machinery in opencast mines. Due to low visibility, mining operations cannot be carried out as drivers are easily prone to accidents. This paper proposes a technique that includes developing a vision enhancement system called perceptive driving assistant system for increasing visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery at opencast mines during harsh weather conditions to overcome the problem. The system consists of high-quality Internet Protocol cameras and thermal cameras for real-time image processing and other well-defined devices, which is quite capable of enhancing the visibility of the image, outlining edges of the road, and detecting obstacles present on the path of operators for smooth driving and reducing threat of accidents. A high-speed graphical processing unit has been used for quality-performance parallel computing, which is well suited for real-time operations to empower fast real-time operations. The calculated frame per second (fps) of image enhancement, object detection, and edge detection is 17.91, 15.91, and 25.09 fps, respectively. The actual frame rate is 26.07 fps, and after applying the algorithm, the final frame rate is 19.65 fps. The calculated accuracy of the object detection model is 81.23%. Field trials indicate that the developed system has performed adequately during foggy weather.

Sep 21, 2022

By Ramiro da Conceição do Nascimento, Horst Guenter Feldhagen, Rafael Piumatti de Oliveira

Mixed hydroxide precipitate (MHP) is a nickel intermediate product that has economical benefits to downstream leaching of lateritic marginal ores. Usually, this product is subsequently processed and refined to produce nickel by hydrometallurgy, but an alternative route can be made integrating hydrometallurgy and pyrometallurgy. Assessing the overall consumption of ferroalloys to obtain stainless steel, as an increasing practice performed in China, the synergy of nickel extraction from laterites by leaching and precipitation asMHP with the production ofMHP agglomerates applied as rawmaterial to furnaces of ferronickel production is a very attractive practice. This work aims to further the technological development of an agglomerated product feasible to hydro-pyro integration. The agglomeration experiments were performed by traditional pelletizing (firing the pellets) and cold bonded pelletizing (aging the pellets by appropriate stocking). Appropriate compositionswere prepared withMHP, additives and binders for each of these routes. A specific study of binder composition was made to find an adequate melting point. The produced pellets were tested to prove their properties by crushing strength tests. The standardization applied to iron ore was followed. The best result of crushing strength was 98.52 daN/pellet. The agglomerates with approved crushing strength for use in electric furnaces were smelted to produce alloys containing nickel; the agglomerates were characterized by scanning electron microscopy. The alloy obtained was metallic ferronickel with sulphide precipitates. Therefore, MHP pellets can be precursors of nickel alloys, which have to be refined to obtain the desirable composition.

Jul 6, 2020

By Eric Lutz

"Great effort has been expended for more than 40 years to improve the workplace safety and health of surface and underground miners across the United States. When looking at the past decade, withstanding the 2010, Upper Big Branch (UBB) disaster that took the lives of 29 miners, this effort has resulted in a generally decreasing trend from 57 fatalities (22 coal; 35 metal/non-metal) in 2005, to 45 (16 coal; 29 m/ nm) in 2014. Through August of this year, there have been 23 mining-related deaths (eight coal; 15 m/nm). These results reflect continued diligence and perseverance on the part of miners that stay true to our legacy; and demonstrate significant investments from mine-site leadership, mining corporations, and state and federal regulators. However, over the past five years there have been an average of 32 fatalities per year, with a low of 36 (2011 and 2012) to a high of 45 (2014). If we know that there will be somewhere between 30 and 50 mining related deaths next year, which of us will volunteer to be counted as one of the numbered? Clearly, we all agree that one fatality is too many; and as evidenced by changes following UBB, deaths in any sector are deaths reflective of all mining across all sectors.The impact of each miner death touches us all. Miner’s deaths are felt deeply by family and friends, most significantly the children; their communities in which they served, supported, and worshiped; and by society that has lost a hardworking, dependable contributor. Further, to take a slightly cynical, but realistic view, miner fatality events impact the financial vitality of mining and contracting companies and broadly diminish investor confidence. Just as important, these events significantly impact our communities and result in negative public perceptions, which ultimately drive regulatory policy and related compliance pressures. This resulting pressure forces operations to broadly address safety and health gaps in very specific ways (i.e., see U.S. Mine Safety and Health Administration (MSHA) regulations regarding lids for trash cans) minimizing a mine site’s opportunities for operational flexibility. To break this cycle that is the operational reality, mining companies are focusing tremendous efforts on fatality prevention and specifically on dedicated investment to prevent multiple fatality events."

Jan 1, 2015

By J. F. Brune

This is a shortened version of the paper ?The Methane-Air Explosion Hazard Within Coal Mine Gobs published in the 2013 volume of SME Transactions (Brune, 2013). This paper analyzes the explosion hazard resulting from the formation of methane-air mixtures in the mined-out gobs of underground longwall coal mines. Evidence from numerous mine explosions suggests that explosive methane zones can form within longwall gobs. Explosions and fires resulting from these methane accumulations have led to severe and fatal injuries to the miners, including the explosion of the Upper Big Branch mine in West Virginia, where 29 miners lost their lives. The paper also reviews current research on numerical modeling of gas flows in longwall gobs and outlines how targeted injection of nitrogen into gobs can effectively reduce the volume of such explosive methane zones. The paper concludes that comprehensive monitoring of gas compositions along the accessible fringes of the gobs along with inertization, improved ventilation schemes and further research are necessary to control this explosion hazard and make mining operations safe.

Feb 23, 2014