Search Documents

By S. K. Singh, J. Shepherd

"Feather edging"- a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar ('total') extraction coal mine.

Jan 1, 1999

By G. Deschênes

In Part I of the work, gold and silver were shown to be efficiently extracted from Kupol samples using lead nitrate in a cyanide leach system. In Part II, a comparison of the technical and economic merits of a new technology called CELP (CANMET Enhanced Leaching Process) was made with the cyanidation/AVR(Acidification-Volatilization-Recycling) process using 8 metallurgical variability samples as well as a large composite sample which represented initial two years of Kupol mill feed. The composite sample had 33.4 g/t Au and 289 g/t Ag. The metallurgical demonstrated that the CELP produced very similar gold and silver leach extractions compared to the standard Cyanidation /AVR leach conditions at 1/2 the cyanide concentration (1000 ppm NaCN in CELP vs. 2000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton, were approximately the same for the two technologies (total cost of the CELP with the use of Merrill-Crowe at $46.48/ton, with cyanidation/AVR at $46.13/ton). However, the implementation of the CELP would eliminate a capital expenditure of approximately $5 million. Eight variability samples used to confirm the previous results showed that on average the gold and silver leach extractions with the CELP and the feasibility leach conditions were very similar for gold extractions, but 4.6% higher for silver extractions compared to the conventional cyanidation. The decision was made to remove AVR cyanide recovery from the Kupol flowsheet and implement the CELP at Kupol. The ability to use conventional leach equipment with the CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2009

By C. F. Barter, H. G. Kreis, D. S. Weber

Before and during in situ mining at the Santa Cruz In Situ Copper Mining Research Project test site, hydraulic testing was conducted at injection and recovery test wells to characterize patterns of fluid movement in the 5-spot well field. Testing included borehole spinner flow meter surveys, single-well and multiple-well injection and recovery tests, straddle packer injection tests, and bromide pulse tracer tests. Results of hydraulic testing for determination of fluid flow regimes were used to modify well and mining zone hydraulics for the purpose of increasing fluid migration in flow pathways of the mining zone with higher copper grade.

Jan 1, 2000

Like the Summer Olympics and U.S. presidental elections, MINExpo comes along once every four years. More than 35,000 people attended the last MINExpo and there is talk that there will be more this time. Just about every company that has anything to do with mining, 1,822 to be exact, will exhibit their wares at the show, but it is the ones rolling in the massive equipment that make MINExpo the show that it is. The following is a glimpse at some of the companies and equipment that you can expect to see at this year?s MINExpo.

Jan 1, 2012

By H. Wesley Peirce

Arizona embraces portions of two major western-U.S. physiographic-geologic provinces and a smaller, local one. These exert fundamental control over the geologic framework and associated earth-material resources and potential. The Mogollon Rim diagonally crosses the State and separates the Colorado Plateau Province to the northeast from the Transition Zone and Basin and Range Province to the southwest. More than 90 percent of the population, production of nonfuel minerals, agricultural land, and water resources are in the Basin and Range part of the State. In 1981 Arizona was ranked number one in the Nation with respect to the value ($2.56 billion) of nonfuel-mineral production. About 8.2 percent of this amount ($212.9 million) can be attributed to nonmetallic (industrial) materials. Although a diversity of nonmetallic substances is produced and some are exported, the bulk is utilized within the State and is directly related to market growth. Since 1950 there has been a fourfold increase in Arizona's population, a concomitant twelvefold jump in sand-gravel production (tons), and a twentyfold increase in "stone" production. New industries developed during this time include cement, salt (and storage of liquid petroleum gas products in solution cavities in salt), zeolite, hydrofrac sand, vitrified clay pipe, crushed marble products (teed additive, pool sand, roofing granules, etc.), and "rock" wool. Most of these newer industries serve out-of-State as well as in-State markets. In 1981 at least 225 industrial mineral or rock deposits were being worked to produce about 10 tons of material per Arizona resident per year. In 1980 the relative values of basic industrial minerals produced in the State, by major group, were cement and lime (51.6 percent); gravel (26.5 percent); sand (11.8 percent); stone (4.6 percent); and others (5.5 percent). Detailed knowledge of the nonmetallic rock-and-mineral content of most Arizona ranges and basins is lacking. Exploration opportunities in this sun-belt growth region appear encouraging.

Jan 1, 1987

By A. Juganda, F. WILSON, H. PINHEIRO, N. SANDOVAL, J. F. Brune, G. E. Bogin Jr.

To evaluate methane explosion hazards in longwall coal mines, a CFD model was developed along with a 1/40th-scale, optically accessible model of an underground longwall coal mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met for accurately representing the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure, and gas concentrations. This research will help develop strategies for methane monitoring that prevent methane ignitions and explosions in longwall coal operations.

Aug 15, 2022

By A. Karami

It is well established that an ordered sequencing of charge initiations in a blast pattern is an important design consideration that affects blasting performance. Delay times must be chosen such that damage to the rock mass is controlled. The accuracy of delay detonators is also of major concern. A large scatter could lead to an incorrect blast sequencing that would lead to damage to the rock mass causing increased over-break, degraded fragmentation, increased fly-rock and poor vibration control. In this study, the effect of using accurate delay detonators on the explosive energy generated is investigated. For this purpose, power spectral density of the blast vibration for delayed shots are calculated and compared with the case where holes are shot at the same time (no delay). At the end the results are presented and discussed.

Jan 1, 2000

By Omid Asghari, Amin Mousavi, Arshad Ranjbar

Geometallurgical modeling of the production benches is an attempt to estimate the geometallurgical variables of the different ore domains, which leads to a better understanding of the ore and its properties. Having geometallurgical variables results in a more accurate prediction of ore characteristics, an improved drilling and blasting operation, and better efficiency of the processing plant. In this research, the geometallurgical variables required for the geometallurgical modeling of the extraction benches are discussed. Then, the relations between Bond work index (BWi), as one of the most important geometallurgical variables and the primary grindability index, and rock geomechanical properties are investigated based on the previously published studies. The BWi is the main parameter for measuring the resistance to the grinding of ore minerals. It represents the energy required for processing (e.g., crushing, grinding) ore rocks in the beneficiation plant. As a real case study, BWi of a production bench in Sungun Copper Mine, located in East Azarbaijan province, Iran, was estimated. The rock’s geomechanical properties were measured using laboratory tests, including uniaxial compressive strength, Brazilian tensile strength, point load strength, and hardness. Then, BWi was estimated using the proposed formulas in the literature and the results of the rock’s geomechanical properties. The selected bench consists of three ore zones and two dyke domains. The laboratory tests revealed that the first ore zone has a slightly higher compressive strength than the other two zones, while the compressive strength of the waste rocks is larger than the ore domains. Using the proposed equations in the literature, the predicted values of the BWi for the samples in ore zones are in the range of 6.36 – 14.44 (kWh/t), and therefore this wide range must be considered when the short-term production schedule is planned. In addition, variations are observed in the samples within a specific zone and between the ore zones, demonstrating heterogeneity in the selected bench. Finally, wide-open results obtained by different equations show a necessity to perform a geometallurgical program specifically for the Sungun mine.

Oct 28, 2021

By Taekhee Lee, Steven Mischler, Shawn Vanderslice

Diesel-powered equipment is widely used in the underground mining industry and their popularity results from properties including efficiency, versatility, reliability, and durability. In the U.S. approximately 7,700 diesel engines were used in 177 underground metal and nonmetal mines as of 2005 [MSHA 2005], and these numbers have likely increased since that time. Diesel engines have been shown to be a major contributor to submicron carbonaceous, respirable, and total particulate mass in the air of underground metal mines [Zielinska et al. 2002, McDonald et al. 2003], and their extensive use results in approximately 13,000 underground metal/nonmetal (M/NM) miners (MSHA 2005) in the U.S. being potentially exposed to aerosols and gases emitted by diesel engines (MSHA 2001, MSHA 2006). Exposure to diesel exhaust has been linked to adverse health outcomes including cancer, cardiovascular, and respiratory diseases (Attfield et al. 2012, Silverman et al. 2012), and in 2012 diesel exhaust was categorized by the International Agency for Research on Cancer (IARC) as a Group 1 human carcinogen (IARC 2012). Exposure to diesel particulate matter (DPM) is especially concerning for underground miners since underground mine environments have been shown to have some of the highest levels of diesel exhaust in the U.S. (EPA 2002, MSHA 2001, MSHA 2006, Pronk et al. 2009). Due to the potential for elevated DPM concentrations in mines, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/ nonmetal underground miners to DPM to an eight-hour time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, MSHA 2006, MSHA 2008). Since this rule went into effect, DPM exposures have been reduced, but are still elevated when compared to other occupations (Pronk et al. 2009, Noll et al. 2015). MSHA compliance data between 2005 to the present show that underground blasters represent 21% of all DPM overexposures in M/NM mines and are one of the highest exposed professions in mining often resulting from low ventilation in the area where blasters are working. Because mines have difficulty controlling DPM in these low ventilation areas, additional control technologies may be needed to reduce exposures. Administrative controls, where miners work on off schedules or upstream of diesel vehicles to avoid the exposures to DPM (Noll et al. 2015) is one possibility, but these types of solutions are not always feasible or practical. A canopy air curtain is another potential control technology to help reduce exposures of blasters to DPM. Listak and Beck (2012) showed that this control technology reduced respirable dust concentration under a roof bolter’s canopy by 67%–75% and recommended air velocities greater than 0.5 m/s for dust reductions of greater than 50%. Additional work showed that a canopy air curtain could be designed for a shuttle car, and some initial testing by the National Institute for Occupational Safety and Health (NIOSH) showed reductions of respirable mine dust between 66% to 70%. As seen in Figure 1, the canopy air curtain delivers clean air over the operator’s breathing zone. A fan draws in air through a filter to capture the dust and then supplies clean air beneath the canopy where a miner is working. The use of the canopy air curtain to reduce exposures to diesel particulate matter was first discussed by Noll et al. (2020). In this study the diesel canopy air curtain (DCAC) reduced the DPM concentrations under the canopy by up to 90%. For this research the DCAC was designed to attach to the basket cover of an ammonium nitrate fuel oil ( ANFO) loader (Figure 2) and provide clean air blowing over the miners as they work in the basket. The initial tests used clean air drawn from the mine’s intake and did not try to filter the DPM from the air. Filtering DPM has extra challenges when compared to filtering mine dust particles. The particles of DPM are smaller (submicron and nanometer) than dust particles (greater than 1 micron); therefore, the filtration system must be adjusted to capture submicron particles. A MERV 13 filter was used in previous canopy air curtain research on mine dust control, but this filter is only designed to capture 50%–75% of submicron particles, and this capture efficiency is too low for removing DPM, so a higher efficiency filter is needed. Higher efficiency filters increase the pressure across the filter media which results in decreased airflow or leaks around the filter and reduces the effectiveness of the control for protecting miners from DPM. The optimal filter needs to capture DPM particles at a high efficiency while still allowing the needed airflows to prevent contaminated air from entering the miner’s breathing zone. Listak and Beck (2012) recommended velocities greater than 0.5 m/s for dust reductions of greater than 50%. However, airflows too high have been shown to reduce miners’ thermal comfort; Roghanchi et al. (2016) suggest the optimal velocity for thermal comfort is between 1–2 m/s. Thus, airflow over the miner should be limited to the range of 0.5 to 2.0 m/s. This current study presents the results from research evaluating the reduction of DPM concentrations, under the DCAC, when using a higher efficiency filter (MERV 16) to remove DPM from the DCAC airstream.

Feb 1, 2024

By L Usoni

Collectors commonly used in flotation to date fall into two main classes: ionic and nonionic. The use of neutral or oily collectors is generally limited to the flotation of nonpolar minerals onto which they are adsorbed by forces of a physical or 'Van der Waals' type, while ionizable chemical collectors are utilized for all other types of minerals, adsorption in this case involving bonds essentially of a chemical nature. Though chemical adsorption is more selective than physical adsorption, even heteropolar collectors are active towards certain classes of minerals (sulphides for example) rather than towards one individual mineral. Thus, in order to float a given mineral from a mixture of minerals belonging to the same class, modifiers have to be used to render the action of the collector more specific. However, there are often considerable difficulties involved in this procedure and the desired results are not always attained, especially in the case of minerals of complex composition whose surface properties are not sufficiently well known. Hence the importance of seeking out collectors capable of linking selectively with given minerals. Selective linkage is possible if the collector structure incorporates active groups having specific affinity for certain cations characteristic of the mineral surface. The decision to investigate the possibility of utilizing chelate--forming reagents for flotation was based on the premise that phenomena which occur in solution and involve chemical reactions in the strict sense of the meaning and those which occur on the surface are closely correlated (1)

Jan 1, 1971

By Peter Loehr

Full-face tunnelling machines were introduced into German coal mines 12 years ago. It was aimed to utilize these highly efficient systems to drive mine tunnels in rock so that the large demand for development work in some mines could be met. A characteristic feature of coal deposits in Germany - and particularly in the Ruhr Area - is a thick overburden strata. Access is therefore only possible through vertical shafts. A network of horizontal drivages leading from these shafts open the deposits between the different mine levels. The hardcoal-bearing formations are multi-folded and heavily tectonically stressed. Apart from a few extensive fault zones there are many single faults of different natures in the carboniferous strata. During the course of decades coal mining has penetrated to ever increasing depths. Nowadays coal is mined from depths of between 600 m and 1,200 m. The effects of ground pressure in connection with extremely varying rock strengths and high temperatures are particular difficulties which have to be overcome during drivage work. The first full-face tunnelling machines to be applied in the mines had originally bee deigned and developed for tunnelling projects. Not only the machines themselves, but also the back-up equipment had to be adapted to meet the special demands of German coal mines.

Jan 1, 1983

By Jon A. Hummer, MICHAEL R. SHAHAN, Aleksandar D. Bugarski, Shawn Vanderslice

Occupational exposures to respirable dust and submicrometer aerosols emitted by diesel-powered equipment are a health concern for underground mining operators and regulators. A study was conducted in an underground mine with the objective to identify, characterize and source apportion airborne aerosols at the setup face and recovery room during longwall move operations. 

By H. C. Liang

Reverse osmosis (RO) and nanofiltration (NF) are widely regarded as being best available technologies (BATs) for removing contaminants of concern from water. In recent years, NF or RO treatment has increasingly gained more acceptance in the mining industry for treating mine water to remove a wide assortment of contaminants, either for meeting discharge standards or for internal re-use in mining processes. Consequently, the number of NF or RO membrane mine water treatment facilities has steadily increased. Although NF or RO membrane filtration can be a powerful tool in mine water treatment, especially when multiple contaminant removal is required, it also has many potential disadvantages. Besides the generally higher capital and operational costs for the high pressure membrane processes, organic constituents in mine water may foul the membranes, while inorganic compounds such as gypsum, calcite, or silica are liable to scale the expensive membranes if proper pre-treatment processes are not implemented. Additionally, because these membrane treatment processes generate a substantial reject or brine waste stream in addition to the clean treated water or permeate stream, brine management also needs to be considered carefully when deciding upon the viability of an NF or RO mine water treatment process. Because of these issues, it is important to conduct detailed analyses of the trade-off between selecting NF or RO vs. using chemical treatment processes when designing a mine water treatment facility.

Jan 1, 2012

By William Gleason

"The city of Denver, CO has experienced extreme growth in the past decade, with the population of the city topping more than 700,000 people in 2018. The current storm water drainage system was put in place in the early 1900s and has not been able to keep up with the growth of the city.When it rains north and east of the city, the runoff goes toward the South Platte River. With the dense population and sometimes severe thunderstorms in the summer, the city has experienced significant flooding that not only endangers lives of residents, but some of the storms have caused millions of dollars of property damage.The Platte to Park Hill Project is a $298-million nearterm, four-phase solution to the flooding that includes the Globeville landing outfall; an open drainage project in the Cole neighborhood in north Denver; an area for temporary water detention and another temporary water detention in Park Hill.The largest and most complex phase of the project is the Globeville landing outfall — a $70-million box culvert project that includes a pair of 157-m (515-ft) long, 243-cm (96-in.) diameter storm water tunnels that pass beneath a busy rail yard with 17 tracks for the Union Pacific Railroad (UPRR) and two Regional Transportation District (RTD) commuter rail tracks. The tunnels, which were installed parallel to a pair of existing 243-cm (96-in.) tunnels, were designed by Brierley & Associates as a client of Merrick & Company for the City & County of Denver, and Bradshaw Construction constructed the one-pass tunnels.From the start, it was evident that the tunneling portion of the project would be the most challenging because of the rail yards.“It’s a little bit more complicated because the railroads have such tight restrictions for settlement,” said Rebecca Brock, Brierley’s project manager. “We had a lot of meetings with Union Pacific and RTD to figure out what are prescribed versus tolerable settlements.”“The portion extending beyond the UPRR under the RTD rails was challenging, as RTD is new to tunnel installations under its tracks,” said Lester Bradshaw, president of Bradshaw Construction. “The RTD tracks employed a unique foundation of continuous concrete with integral raised concrete ties on rubber bushings. Minimizing settlement to these tracks was a critical requirement.”"

Jan 9, 2018

By Georgios Bartzas, Vasiliki Karmali, Konstantinos Komnitsas, Anna Kritikaki, Dimitra Vathi, Stylianos Tampouris, Arne Peys

Large volumes of slags, with varying mineralogical and geochemical characteristics, are produced annually by the ferrous and nonferrous metallurgical industry. Most of them are considered as potential secondary resources and may be valorized, following the principles of circular economy, for the recovery of critical elements, including energy transition metals. Apart from the economic benefits, valorization of slags may contribute to the competitiveness of the metal industry and the conservation of natural resources. Valorization also results in minimization of environmental impacts on soils and waters in slag disposal areas, due to the prevention of solubilization and subsequent migration of potentially hazardous elements. The present study utilizes ferronickel (FeNi) slag for the production of alkali-activated materials. The effects of the main experimental parameters, including sodium hydroxide (NaOH) molarity, silica/sodium oxide (SiO2 /Na2O) molar ratio in the activating solution, precuring and curing time, curing temperature and aging period on several properties of the final products, are assessed.

Apr 1, 2025

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By JOHN HOMER, Jacob L. Carr, Jonathan K. Hrica, Kathleen M. Stabryla, Iman Benbourenane, Jennica L. Bellanca

Given the recent focus on powered haulage incidents within the US mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the available research literature is timely. This paper describes a rapid review that identifies, characterizes, and classifies the research literature to evaluate the maturity of CXS technology through the application of a Technology Readiness Assessment. Systematic search methods were applied to three electronic databases, and relevant articles were identified through the application of inclusion and exclusion criteria. Sixty-four articles from 2000 to 2020 met these criteria and were categorized into seven CXS technology categories. Review and assessment of the articles indicates that much of the literature-based evidence for CXS technology lies within lower levels of maturity (i.e., components and prototypes tested under laboratory conditions and in relevant environments). However, less evidence exists for CXS technology at higher levels of maturity (i.e., complete systems evaluated within operational environments) despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for systematic peer-reviewed research to evaluate the performance of CXS technologies and demonstrate the efficacy of prototypes or commercial products, which could be fostered by more collaboration between academia, research institutions, manufacturers, and mining companies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions. However, this contrasts with haul truck fatal accident statistics that indicate that most haul truck fatal accidents are due to vehicle-to-environment interactions (e.g., traveling through a berm). Lastly, the relatively small amount of literature and segmented nature of the included studies suggests that there is a need for incremental progress or more stepwise research that would facilitate the improvement of CXS technologies over time. This progression over time could be achieved through continued long-term interest and support for CXS technology research.

Jun 17, 2022

By M. Paul

"INTRODUCTION In 1990, the uranium production of SDAG Wismut in East Germany was stopped. 45 years of inconsiderate destructive exploitation had scarred both landscape and nature. With the “Wismut law” which came into force in December 1991, the Federal Republic took responsibility of the remediation of the legacies from former uranium ore mining and milling in Saxony and Thuringia. A unique opportunity turned out in order to remove environmental damage, to enhance the life quality of the local population, to shape new landscapes and to advance the economic restart. (1) The results of nearly 25 years of remediation activity are evidence that this opportunity was used at all former SDAG (Sowjetisch-Deutsche Aktien-gesellschaft) Wismut sites. The reference project “Wismut“ has evolved into a joint project of all parties involved and radiates beyond the affected regions. This is particularly reflected by the Know-how transfer starting from Wismut and the increasing activities for third parties abroad.WATER MANAGEMENT AT WISMUT REHABILITATION Within the Wismut project, water management and conventional technical water treatment are by far the most cost-intensive long-term tasks of the remediation programme. Over the medium term, there is no viable alternative to the operation of active systems to catch and treat contaminated mine waters at the Ronneburg, Schlema, Königstein, Pöhla, Seelingstädt and Helmsdorf sites. Based on the status quo, this paper outlines the key issues of the Wismut GmbH water management strategy over the medium and long term. It is focused primarily on achieving protection goals for potentially impacted water bodies in the surroundings of Wismut sites and on optimising associated remediation expenditures as well as on creating the prerequisites for achieving low post-remedial care and maintenance or walk-away system status over the long term. (2) The applied mining practices during the active SDAG Wismut period have not been up to the high standards of modern mining operations and their requirement to leave former production premises and deposited residues in a condition that was not only physically but also chemically stable. Rather the emission of mine and seepage waters laden with high acidity, metal and salt content is a frequent corollary and difficult legacy of historic mining and processing operations (4, 5). As a consequence, the control or mitigation, respectively, of environmental impacts associated with contaminated mine waters ties up enormous public resources worldwide (6, 7)."

Jan 1, 2016

By R. E. McIvor, Brian Cornish, J. A. Finch, Yue Tan, Claude Gagnon

Fred C. Bond is recognized throughout the mineral processing world as the father of comminution equipment applied science and engineering. The Bond Work Index became a universal standard, and is the most widely used measurement tool for comminution energy consumption. This biography is the story of his lifetime of study, work experiences, experimentation, analyses and findings. His numerous published writings are reviewed. His legacy is one of comminution process engineering that will be used in perpetuity.

Feb 1, 2024

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993