Search Documents

By A. L. Hinde, P. J. D. Lloyd, A. R. Atkins, J. G. MacKay

The control of milling circuits by A. R. ATKINS, M.Se. (Elee. Eng.) (Visitor), A. L. HINDE, S.Se., Ph.D. (London) (Visitor), P. J. D. LLOYD, S.Se. (Chem. Eng.), Ph.D. (Cape) (Fellow) and J. G. MACKA Y, S.Se. (Chem. Eng.) (Visitor). The general behaviour of mills is described in an attempt to find a control philosophy that will permit milling circuits to produce a constant particle size. Although the experimental work has been confined to a single section of the milling circuit of one mine, it is felt that the findings are applicable to other milling circuits.

Jan 6, 1974

By D. J. Adams, R. G. Gürtunca

This paper describes the results obtained from a rock-engineering monitoring programme carried out at West Driefontein gold mine, where dewatered and classified tailings have been used as backfils for local and regional support. The in situ behaviour of these backfils and the surounding rockmass were determined, and it was found that the backfil used on this mine has provided significant regional support. The underground observations also showed less rockburst damage in backfiled panels than in unfiled panels, provided the backfil had been placed properly in the stopes.

Jan 1, 1991

By D. A. Viljoen

An account is given of the development of man's interest in the recovery and working of minerals from Palaeolithic times to the present. This is followed by a discussion of future production trends for the more important minerals, and of likely technological developments in the recovery of various minerals. The crucial importance of energy minerals is stressed, as are several other factors of significance to a flourishing minerals industry: manpower, education, financial climate, Industrial health and safety, and preservation of the environment.

Jan 1, 1979

By H. A. D. Kirsten

The paper reports on loading tests conducted on shotcrete reinforced with mesh and various types of steel fibre, and compares the results with the energy absorbing capabilities of 16 mm rebar shepherd's crooks. It is concluded that mesh-reit1forced shotcrete has sufficient energy-absorbing capabilities to contain rockbursts of significant magnitude, having greater energy absorbing capabilities, even at a thickness of 50 mm, than 16 mm rebar shepherd's crooks. Fibre-reinforced shotcrete has energy absorbing capabilities of the same order as, or better than, those of 16 mm rebar shepherd's crooks, but its performance is erratic.

Jan 1, 1995

By A. A. Bradley, K. H. Stanton, P. J. D. Lloyd

A theory for the dynamic balancing of centrifugal mills is presented that takes account of the mass and shape of the charge in a gyrated grinding tube and the way in which the charge lags behind the centrifugal force vector. predicts that a corresponding lag in the angular position of the counterweight centres of mass is necessary, and that the fractional filling should be increased if the ratio of gyration diameter to tube diameter is decreased. A worked example is given for a I MW centrifugal mill that was balanced adequately by the methods described.

Jan 1, 1983

By Adams. M. D.

Most of the cyanide lost in carbon-In-pulp plants is due to the reaction of cyanide with base metals and sulphides during leaching. Some cyanide is also lost in the adsorption tanks as a result of oxidative and adsorption reactions with the activated carbon. The high rates of cyanide loss in the elution and electrowinning stages are atributable to hydrolytic decomposition and anodic oxidation, respectively. However, the relative amount of cyanide lost during these two stages is small for a given amount of ore treated.

Jan 1, 1990

By N. O. Lotter

Evaluation errors and value frequency distribution models of the gold ore bodies in the Witwatersrand and Free State systems are reviewed. It is found that the low-grade sections of the data are prone to the largest evaluation errors, and that an understanding of the shape of the value frequency distribution is essential to the calculation of mean grade. The evaluation of a mineral process for a particular ore requires attention to mil-feed sampling, sample processing, and monitoring. In particular, the calculation of a representative mass of mill-feed sample (Ms) should take account of size-by-size value variance. Alternative Ms models are discussed.

Jan 1, 1995

By J. A. Tyser

The pumping of water from mines in the Central Witwatersrand by J. A. TYSER, Pr. Eng., B.Sc. (Min.) (Associate) This paper describes a system for the removal of underground water in the mines of the Central Witwatersrand, some of which are defunct. The water is pumped by a pump station on 24 level at E.R.P.M. to a surface lime plant and then to a surface treatment plant, where it is treated so that it meets the specification of the Department of Water Affairs relating to the deposition of water in public streams.

Jan 5, 1977

By A. B. Stewart, I. J. Barker

Traditionally it has commonly been believed that the only problem with inductive reactance in a submerged-arc furnace is that it leads to difficulties with the electricity supply as a result of the Iow power factor. This paper sets out to show that inductive reactance can also give rise to the following problems in the metallurgical operation of a furnace: (i) dead and live phases (fairly well known in openarc furnaces), (ii) lack of sensitivity to electrode movement, (iii) interactions between electrodes. These problems increase with increasing inductive reactance relative to resistance, and thus they increase with furnace size. Each of these effects is discussed in detail, and suggestions are made for their alleviation.

Jan 1, 1980

By L. Woollacott, R. P. King

Although several models for the carbon-in-pulp (CIP) or carbon-in-leach (CIL) processes have been published, most of these models do not consider in detail the way in which the carbon phase flows on large-scale plants. This paper illustrates the importance of these details if the CIP or CIL process is to be modeled correctly. An appropriate model, based on population-balance techniques, is then derived. Suitable mathematical techniques for the solution of the model equations are also described. Finally, a method for estimating the model parameters for a full-scale plant is described.

Jan 1, 1990

The support of stopes by means of yielding timber props, with or without hydraulic props, is common in the mining industry. This paper discusses the ability of these support systems to absorb energy during a rockburst, and further investigates their capability to withstand a range of ground velocities. It is found that the rate of stope closure prior to a rockburst strongly influences the behaviour of these support systems during the rockburst. It is recommended that hydraulic props be used in conjunction with yielding timber props in these conditions, and that yielding timber props with an increased yield range are desirable.

Jan 1, 1991

Measurements of the rates of penetration at various throttle air pressures are presented as a function of thrust for three different rockdrills when drilling quartzites with strengths of 45 000 lb/in2 and 39 000 lb/in2, The rate of penetration at optimum thrust is shown to agree well with the predictions of theory and curves of air consumption as a function of throttle air pressure are presented. Man-held machines are shown to be under-thrusted at throttle air pressures above 40 lb/in2g. Measurements of bit wear as a function of distance drilled are presented graphically and discussed in terms of the theory developed in Part 1.

The rising tide of environmentalism has adversely affected many mineral producers, but it has also provided them with a number of opportunities for mineral applications. These markets are as diverse as water treatment, waste disposal, and flue-gas desulphurization. Whilst legislation is forcing up the industry's environmental standards, the advent of environmental management provides an opportunity for producers to display its 'green' credentials. The picture painted of the extractive industry by environmentalists is undeservedly black, because the more efficient a producer is, the more effectively that producer conserves the very resources he exploits. The 1993 IM Forum examined these issues and how they affect the mineral producer, and this publication comprises the papers presented at that meeting.

Jan 1, 1995

By A. Whillier

Recovery of energy from the water going down mine shafts by A. WHILLIER, Pr. Eng., Se. D. (M.I.T.) (Fellow) The influence of energy-recovery systems on the rise in temperature of water going down mines is examined. It is concluded that the, cost benefit of such systems, deriving partially from the reduced temperature rise in situations where cold water IS sent underground from surface, would more than justify the installation cost.

Jan 4, 1977

By I. Wayland

Value added blasting is a process methodology that links tasks and processes, with the aim to improve/enhance the technical application of explosives technology and initiating systems, resulting in improved output. The phases and steps of a typical value added blasting intervention are discussed in this paper. Each step having distinct purposes, principles and methodology. The underlying philosophies and process steps of the programme are described for each step. This paper gives an account of projects that have been completed in two Anglo American Gold Mines. This will include a description of the projects that were conducted at Vaal Reefs 8 Shaft and Western Deep Levels South Mine covering: ? The need for blasting improvements ? The approach that was followed ? The result of the programme.

Jan 1, 1999

By G. B. Lundstrom

SYNOPSIS For some time, Vaal Reefs South has operated blindhole borers successfully as an integral part of the mining cycle of operations. To date, over 13 000 m of mechanized boxholing has been completed, and from time to time impressive performances have been achieved. The paper describes the machines, the modus operandi, and the structure of the boring organization at the Mine, with some of the results recorded. The Mine recently took delivery of two new machines with interesting design features. The introduction and early experiences with these two machines are also described.

Jan 1, 1985

By M. Sciarone, B. Collins

The production, properties, and selection of ferrosilicon powders for heavy-medium separation by B. COLLlNS. B.Sc Eng. (Rand) (Fellow). T. J. NAPIER-MUNN. B.Sc. (Eng.). A.R.S.M. (Visitor). And M. SCIARONE. M.Se. Eng. (Delft) (Visitor). There are basically two types of ferrosilicon powder available to operators of heavy-medium plants in South Africa spherical and milled grades. The production processes are described, and the properties of the two types are examined and compared. Guidelines are given for the selection of the correct grade of ferrosilicon for any particular application.

Jan 12, 1974

By P. C. Seligmann

Primary fracture from an array of shotholes by c. M. LOWNDS. B.Sc. Hons. (Rhodes). Ph.D. (Cape) (Visitor) and P. C. SELIGMANN. B.Sc. (Witwatersrand) (Visitor) The effects of stress on the directions of cracks that are propagating in a brittle medium are described. It is shown that the superimposition of stress fields from the holes of an array always adversely affects fragmentation. Consequently, the best fragmentation will result when holes are fired far enough apart in space or time for each to develop its whole crack pattern without disturbance from the others. This concept leads to a philosophy for the design of more effective blasting patterns, which has been verified on model scale and which explains many published, empirical results.

Jan 1, 1976

By J P. van Dyk

The dramatic strengthening of the rand against the dollar as well as a decline in quantity and quality of locally available concentrates have had a dramatic impact on Zincor?s operations during the previous two years. Zincor has responded with the implementation of a number of technical improvements to the process to decrease cost and increase revenue and plant flexibility. Among the initiatives is the pre-leaching and pelletising of the zinc concentrate, de-bottlenecking and process improvements in the leach and purification circuits, the introduction of cathode washing and automated cathode stacking in the cell house and the installation of a new furnace to produce pre-alloyed jumbos. This paper will describe these initiatives and others that Zincor have recently taken to stay competitive in changing global base metals market.

Jan 1, 2005

By A. Ball

A fully instrumented laboratory drilling machine is described. It is designed to produce realistic drilling conditions with diamond microbits of 20 mm diameter. A computer-controlled data-logging system records the net power consumption, rotational velocity, bit thrust, torque, and penetration rate. Tests can be conducted under conditions of set thrust and rate of advance. In the tests reported, there is a significant correlation between the rock drilability and the measured rock properties of relative abrasion resistance and uniaxial compressive strength. Wear of a diamond bit is a crucial factor that cannot be determined simply from rock properties. Realistic drilability testing with appropriately scaled microbits is a convenient and economical way of evaluating diamond-bit performance and determining rock drilability.

Jan 1, 1990