Search Documents

By C. M. Sellars, W. E. Stumpf

SYNOPSIS The effects of concurrent recovery, prior creep deformation and concurrent high temperature fatigue on the coarsening of some carbides in steels have been studied. It was found that concurrent recovery enhances the coarsening rate by orders of magnitude and prior creep deformation causes an enhancement of about two times. Finally, concurrent fatigue causes an initial greatly enhanced coarsening rate but after prolonged cycling dissolution of the carbides occurs.

By P. S. Turner

After a brief account of the differences between the control of underground fires and those on the surface, the paper describes the analogue detection system used on the mines of the Anglo American Corporation of South Africa Limited. The system comprises Spanair gas analysers, Becon combustion-particle detectors, a telemetering system, a surface signal-recording and-processing system, and an alarm system. The use of the system is described and illustrated.

Jan 1, 1982

COLLOQUIUM PRACTICAL APPLICATIONS OF INSTRUMENTATION IN THE MINING AND METALLURGICAL INDUSTRIES Rapporteur: J. Laschinger A colloquium and general meeting of the Institute held jointly with the Instrument and Control Society of Southern Africa at Kelvin House, Johannesburg on 18th October, 1972, had as its theme "Practical Applications of Instrumentation in the Mining and Metallurgical Industries" Dr J. P. Hugo (President) was in the chair and about 200 members and visitors were present.

By A. O. Filmer

A study of the dissolution of gold from a pyrite concentrate and from various calcines is reported. The percentage extraction of gold was found to decrease with increasing sulphur content in the material leached because of the porosity of the materials, and particularly because of the passivation of the anodic dissolution of gold when the gold was In contact with other conducting minerals. This is explained in terms of the current-potential curves for the oxidation of gold and the reduction of dissolved oxygen.

Jan 1, 1982

By P. van Niekerk, V. J. Solomon

Improvements in the drilling and blasting techniques used in the stopes of narrow reefs have caused the clearing of broken rock to become the major cause of delay in the achievement of a regular cyclic operation. This paper discusses the development of a scoop in accordance with a predetermined set of performance parameters. The test results obtained to date have shown that the basic objectives have been achieved within tolerable limits of variation.

Jan 1, 1979

By Z. Zitron, G. J. de Korte, D. W. Horsfall

This paper summarizes work carried out on the treatment of fine coal, nominally classified as minus 0,5 mm (wedge-wire screen), which is removed from the raw coal prior to the treatment of the plus 0,5 mm sizes. The minus 0,5 mm coal divides, for treatment purposes, into fines, nominally between 500 and 150 !tm, and ultrafines, nominally minus 150 !tm. Studies on processes for the treatment of minus 0,5 mm coal are discussed, and the lower size limit beneficiated is indicated for each process. The installation and operational results from a pilot froth-flotation plant treating minus 150!tm coal are described.

Jan 1, 1986

By B. Strohmeier

The role of large, ultra-high-powered arc furnaces in a fully integrated steelworks for the production of flat products is outlined, and an account is given of the technological improvements that have been implemented over the past few years to enable the arc furnace to remain competitive against the conventional route using blast furnaces and top-blown-oxygen steelmaking (LD). Modern secondary refining facilities have been installed, enabling the arc furnace to operate at high production rates in the manufacture of high-quality flat products.

Jan 1, 1985

The relationships between backfill-transportation parameters (solids concentration, velocity, and pipe diameter) and the wear rate of backfill-transportation pipelines is well understood. However, the degree of wear experienced by a pipeline depends not only on the transportation parameters, but also on the characteristics of the solids making up the backfill, i.e. the particle-size distribution, hardness, shape, and sharpness of the particles. Therefore, unless data corresponding to the specific wear rate of the solids are available, the determination of the wear rate for pipes transporting an uncharacterized backfill is largely guesswork. This paper describes an evaluation of particle characteristics with special reference to particle sharpness so that pipe wear rates can be correlated with solids of different size distributions and sharpnesses.

Jan 1, 1993

By M. G. Demmer

South Africa ranks among the top three mineral producing countries in the world, and yet the country's teaching and student population have a very limited knowledge of the mining and metallurgical industry. This is probably one of the major reasons why so few scholars elect to study mining-related disciplines at local universities, or to consider a career in the industry. Small mines Much interest in the development of small mines has been evident in the past few years, with junior companies taking the bull by the horns and moving in where larger companies found it uneconomic to tread or, indeed, where large companies are foresighted enough to see the advantage of smaller operations. Examples of small mines are to be found from Europe to Australia, in the Americas, and in

Jan 1, 1986

By R. R. Mankowski

The work described here is an extension of current theory applied to obtaining the power dissipated at the wavefront of a transverse disturbance traveling along a mine hoisting cable. A previously derived empirical relation is adapted to the present problem, and is solved by use of a Lagrange-type reference frame moving with the wavefront. As a result of tie limitations inherent in the original relation, only a lower-bound for the domain of predicted power losses is defined. A qualitative assessment of conditions leading to the undesirable effects of internal frictional losses at the wavefronts are discussed in terms of the operating environment found on typical mining installations

Jan 1, 1990

By M. D. Prendergast

Research into the ferrous metallurgy of Rhodesian Iron Age societies M. D. PRENDERGAST (Visitor) Iron-working was a widespread economic activity in Iron Age Rhodesia, and merits historical and metallurgical investigation. However, the research done so far has been incidental and poorly disseminated. This paper reviews the available evidence and the ways in which it can be interpreted by archaeologists and historical metallurgists. Particular attention is paid to smelting techniques and current metallurgical research, and brief suggestions are made for future research. v074n06p254.pdf

Jan 1, 1974

By R. Hemp

The first part of this paper describes the collection of barometric pressure measurements in a mine and their statistical analysis, which shows the effect of variations in barometric pressure, both on the primary emissions of methane gas into the workings (whether from fissures or from the surrounding strata), and on the flow of air to and from large unventilated, or poorly ventilated, areas. The second part of the paper deals with a study, based on computer simulations, of leakage flows of air into and out of sealed areas, and the reduction of such flows by the use of adequate seals.

Jan 1, 1994

By M. Timucin

High-temperature phase relations in the Pb-PbS system were established by the quenching of samples equilibrated in evacuated and sealed silica capsules. The liquid-miscibility gap seen in some previously published phase diagrams was not observed. The thermodynamic activities of PbS in liquid solutions of this system were derived at 1473 K from the isopiestic equilibration of samples belonging to this solution series with Cu2S-PbS melts of known PbS activities. The behaviour of Pb-PbS melts was found to be compatible with a subregular solution model. This model also made it possible to obtain an analytical liquidus for PbS that was in excelent agreement with the experimental determination.

Jan 1, 1988

By A. J. Jager, G. R. Adams

The pattern of mining-induced fractures ahead of stope faces in deep-level gold mines, as revealed by petroscopic observations, is described. It is shown that there are zones of fractured and unfractured rock ahead of the face, which are about I m wide and continue as discrete entities for at least 12 m parallel to the face and at least 5 m vertically. These zones do not form continuously as mining progresses, but develop from time to time, leaving a solid zone between the fractured zones. The maximum depth of fracturing ahead of the face depends on the rate of energy release.

Jan 1, 1980

By J. J. Geldenhuys

Premier of the North-West Province, Mr Molefe, foreign dignitaries and guests, ladies and gentlemen. It is a pleasure and also a special honour for me to have been invited here this morning to make this address. The xv Congress of the Council of Mining and Metallurgical Institutions is, by its very nature, an extremely important event for the international minerals industry. But I believe that this specific Congress assumes an even greater significance because of the profound and far-reaching changes that have taken place in South Africa this year. These are exhilarating times, a period when so much in our country has altered and when so much has to be done so quickly to build positively on our bold political decisions.

Jan 1, 1994

By B. M. Van Vliet

SYNOPSIS This paper outlines the principles involved in the regeneration of activated carbon for renewed use in the recovery of precious metals or the purification of water. While chemical methods are effective in restoring the activity of spent activated carbon containing only single or defined adsorbates, thermal methods have to be used when the spent carbon is loaded with a heterogeneous mixture of adsorbates such as those normally present in industrial process streams or effluents. The steps involved in thermal regeneration are described, together with the operating conditions that can be controlled to give the required degree of activation. Finally, an account is given of the structural changes that occur in a new or spent activated carbon during thermal treatment.

Jan 1, 1991

By F. P. A. Robinson, C. R. Thomas

Stress-corrosion studies on materials used for surgical implants * by C. R. THOMAS and F. P. A. ROBINSON Samples of Vitallium (a cobalt-chromium alloy), 316L stainless steel, and titanium T318 were subjected to the boiling magnesium chloride test so thattheir susceptibility to stress-corrosion cracking could be determined, and their behaviour under service conditions was then assessed. Stress-corrosion cracking was confined to the stainless-steel samples, while gross pitting was detected in the samples of forged Vitallium. It was concluded that the use of stainless steel should be avoided for long-term surgical implants. Surface imperfections on the stainless steel are generally the cause of pitting, from which stress-corrosion cracks are sometimes propagated.

Jan 11, 1976

By H. J. E. Hamel

Some aspects of the deformation behaviour and temperature rise during instantaneous compression loading of high purity aluminium By H. J. E. HAMEL The influence of deformation speed on the deformation behaviour of high purity aluminium was investigated. By varying the initial height-to-diameter ratio a considerable influence on the deformation behaviour could be noticed. Lubrication of the specimen end faces was found to have an influence on the flow behaviour and on the roughness of the specimen interface at pressing platens. The results of temperature measurements during deformation agree with work-hardening behaviour of the specimens. Flow curves calculated with the measured temperature rises do not agree with results obtained at lower strains by other workers. The possible reasons are discussed.

Minerals and Manpower - PRESIDENTIAL ADDRESS given by R. P. Plewman, Pr. Eng., B.Sc. (Eng) (Wits), M.A. (Oxon.) INTRODUCTION What I want to discuss is the future pattern of manpower in the mining industry, and I should like to begin by examining some relevant statistics. There are four areas that must be examined. Firstly, the future rate of production of different minerals must be estimated. Secondly, an assessment must be made of the balance of different mining technologies likely to be used for each mineral. Thirdly, the manpower requirements for each technology must be determined. And, fourthly, the future manpower resources of the country must be explored. NIM report Report No. 1646 Examination of the methods of analysis for calcium fluoride in fluorspar.

Jan 10, 1974

By K. M. Banks

Multiple-pass hot-strip-rolling schedules of carbon steels and niobium-microalloyed ferrite-pearlite steels were simulated on a Gleeble 1500 thermomechanical test apparatus. The effects of finishing temperature, coiling temperature, and chemical composition on the as-deformed ferrite grain size and hardness of the steels were determined. Low finishing temperatures and low coiling temperatures both contributed to ferrite grain refinement. Good agreement was found for the microstructure and hardness of the steels between the as-ruled condition and the results obtained from rolling simulations. The progress of recrystalization and precipitation was followed from examinations of the flow-stress curves during the hot-rolling simulations. The flow-stress behaviour during the finishing passes was consistent with the resulting changes in final ferrite grain size. It was found that the no-recrystalization temperature, TNR, is raised by increased additions of niobium.

Jan 1, 1993